Post-thermal Treatment Research Articles

Influence of Modification with Iodine and Thermal Posttreatment on the Structure and Electrical Conductivity of Graphene Oxide

Influence of Modification with Iodine and Thermal Posttreatment on the Structure and Electrical Conductivity of Graphene Oxide

Degradation and Migration in Olive Oil Packaged in Polyethylene Terephthalate under Thermal Treatment and Storage Conditions

The research addresses challenges in food safety related to the migration of contaminants from plastics to food. It focused on the physicochemical and sensory degradation of olive oils packaged in polyethylene terephthalate (PET) and subjected to thermal exposure at 40 °C and 60 °C for several weeks and a subsequent 12 months of storage, as well as the stability and migration of compounds from the PET packaging itself. Olive oils (OO) from Spanish supermarkets (a mixture of refined and virgin, with commercial identifications of mild and intense) were selected and subjected to thermal treatments at 40 °C and 60 °C for 1, 2, and 3 weeks, followed by 12 months of storage. The treatments were conducted through the following two independent experiments: Experiment A focused on immediate analysis post-thermal treatment, while Experiment B included a 12-month storage period post-thermal treatment. The presence of antimony (Sb) was analyzed using acid digestion with nitric acid (HNO3) and high-resolution inductively coupled plasma mass spectrometry (HR-ICP-MS), while the metals cadmium (Cd), copper (Cu), lead (Pb), and iron (Fe) were analyzed using inductively coupled plasma mass spectrometry (ICP-MS). The PET characterization was assessed using Fourier transform infrared spectroscopy in the mid-infrared range (FT-IR/MIR), carbonyl index, and differential scanning calorimetry (DSC). The results showed increases in the acidity index by 0.29%, the peroxide value by 25.92%, and the K268 coefficient by 51.22% between the control sample and the most severe treatments, with more pronounced effects observed after 12 months. Sensory quality declined, with reduced intensity of the “fruity” attribute and increased presence of the “rancid” defect. PET degradation was reflected in an increase in the carbonyl index and greater structural amorphization. Fe was the predominant metal, and Sb concentration increased after thermal treatments. The lack of studies on the raw consumption of oils packaged in PET and the concerns about the migration of compounds from the packaging to the food highlight the relevance of this research. This study provides new insights into the effects of thermal exposure and storage on the migration of PET contaminants into oils, contributing to the development of strategies to ensure food safety and product quality.

Characterisation of alkali-treated novel cellulosic fibres derived from Dombeya Buettneri plant as a potential reinforcement for polymer composites

ABSTRACT The present study evaluates the influence of alkali treatment using 2, 4, and 8 wt.% sodium hydroxide concentration solutions on novel cellulosic fibres manually extracted from the bark of dombeya buettneri plant (DBF). Alkali-treated fibres were characterised through physical and mechanical properties determination, Fourier transform infrared spectroscopy, X-ray diffraction, quantitative chemical analysis, thermogravimetric analysis, and scanning electron microscopy. Quantitative chemical analysis revealed a significant increment in cellulose content, reaching 67 ± 1.7% in DBF treated with 4 wt.% NaOH solution, accompanied by substantial reductions in lignin and hemicelluloses as confirmed by FTIR spectroscopy. XRD analysis showed an improved crystallinity index of 80% and crystallite size of 2.64 nm for 4 wt.% alkali-treated DBF. Additionally, 4 wt.% alkali-treated fibres yielded peak values of breaking force (40 N) and breaking tenacity (181 cN/Tex). SEM analysis confirmed enhanced surface roughness post-treatment, an indication of enhanced fibre/matrix interlocking during composite fabrication, whereas TGA analysis reported improved thermal stability post-treatment. EDX analysis confirmed that the C/O ratio is proportional to alkali solution concentration, indicating effective removal of non-cellulosic contents. In conclusion, treating DBF with 4 wt.% NaOH concentration improves their physical, mechanical, and chemical properties, suggesting their potential for polymer composite applications.

Influence of post-thermal treatment on characteristics of polycrystalline hybrid halide perovskite nanoparticles thin film

A three-dimensional organic–inorganic hybrid halide perovskite (CH3NH3PbI2Br) nanoparticle film was synthesized using solution process in one step. Precursors’ stoichiometry was used to prepare methylammonium bromide and lead (II) bromide in dimethyl formamide. The synthesized CH3NH3PbI2Br solution was spin coated on cleaned ITO prepatterned glass substrate at 2000 rpm. In addition, the influence of post-thermal treatment on the deposited nanoparticles films was evaluated by studying the structural, optical and morphological properties using X-ray Diffraction (XRD), Fourier Transform Infrared (FTIR) spectrometry, UV–visible spectrophotometry, Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM). The average crystallite sizes were calculated to be ~ 8.0, ~ 9.4, ~ 11.3 and ~ 13.1 nm of as-prepared and annealed films at 400, 500 and 600 °C, respectively. Besides, the bandgaps of 2.22 eV, 1.96 eV, 1.89 eV and 1.63 eV were extrapolated for as-prepared and annealed films at 400 °C, 500 °C and 600 °C, respectively. From J–V curves, the Jsc values of 9.4, 10.6, 11.7 and 12.8 mAcm−2, FF values of 56.99%, 57.25%, 58.94% and 59.26% and PCE values of 2.99%, 3.49%, 3.96% and 4.39% were calculated for as-prepared and annealed CH3NH3PbI2Br films at 400 °C, 500 °C and 600 °C, respectively. The percentage enhancement values of 14.32%, 24.49% and 31.89% compared to as-prepared CH3NH3PbI2Br film. Hence, post-thermal treatment of organic–inorganic halide perovskite material improved its photoconversion efficiency without sacrificing its dimensionality.

UV-random lasing of ZnO films decorated with Au nanoparticles and modification of lasing threshold by surface plasmon effect

Threshold energy values for random lasing action are determined from spectral and temporal coherence studies in systems with incoherent feedback. Zinc oxide films with and without their surface having been decorated with gold nanoparticles stand simultaneously for the active and the scattering medium, whereas pumping is carried out by a conventional laser system operating at the picosecond pulse regime. The influence of the gold surface on both the threshold and the intensity of the optical response is investigated. Whenever localized surface plasmon resonances are supported, electron mobility at the gold boundaries facilitates reinsertion of the trapped electrons into shallow defect levels to the conduction band. In consequence the characteristic visible emission from ZnO (green) due to transitions from such levels is suppressed, thus lowering the pumping threshold prerequisite for random lasing emission. The tunning of the random lasing threshold is achievable by means of control on the morphology and size effects of the gold nanoparticles. This contribution shows that specific post-thermal treatments could be exploited to adjust the lasing properties of novel metal decorated systems, which already feature random lasing before decoration. In principle, the extension of the decoration should be rather small to minimize response losses due to screening side effects of the metal phase, which obtrudes direct contact of the pumping photons with the semiconductor system.

Understanding the electronic structure and transport properties of A-site SrTiO3-δ ceramics with enhanced configuration entropy

Since SrTiO3 is attractive due to its versatile electronic properties ranging from dielectric to semiconducting behavior, the effect of systematic co-substitution of various A-site cations on the electronic structure and transport properties of oxygen-deficient SrTiO3-δ bulk ceramics was analyzed. The materials were synthesized by reverse co-precipitation method and densified by spark plasma sintering (SPS) in a vacuum, followed by a post-thermal treatment in a reducing atmosphere (5 % H2/Ar). The phase purity was confirmed by X-ray diffraction (XRD), different microstructures were revealed by scanning electron microscopy (SEM), and characterization in terms of electrical conductivity (σel) and Seebeck coefficient (S) were performed. The largest power factor was obtained with Sr0.25Ca0.25Na0.25La0.25TiO3-δ by maintaining electrical conductivity while increasing the Seebeck coefficient. Density Functional Theory (DFT) calculations were applied to obtain information on band structures, the projected density of states (PDOS), and electron density differences (EDD). Band structures indicated that oxygen deficiency essentially changed the conductive nature of the studied materials by shifting the Fermi level to the conductive zone, while PDOS plots define the role of each element located at the A site. The electronic structure is affected to the greatest extent in the cases when Nd and Pr are present at the A-site. However, the obtained experimental and computational (DFT) results could not completely match and explain all phenomena since understanding the effect of different cations at A-site on oxygen vacancy formation seems to be a challenging task, and therefore, some hypotheses are proposed. This work attempts to understand the role of a particular cation at A-site on the electronic band structure and its relevance to the formation of oxygen vacancies, thereby providing valuable insights for future high-entropy perovskite titanates with improved transport properties.

Study of the effects of heating on the physical, optical, and electrical properties of NiO thin films synthesized using a low-cost sol-gel method

Developments in low-cost techniques for growing high-quality nickel oxide thin films (NiOTFs) are critical enablers for the fabrication of NiO-based devices, particularly solar cells, light-emitting diodes, lasers, and many other applications. In this study, it has been demonstrated that the optical, electrical, and structural characteristics of NiOTFs coated on glass substrate employing a low-cost solution method are strongly influenced by post-thermal annealing treatments in ambient air. A comprehensive study was carried out on the characteristics of the deposited NiOTFs. X-ray diffraction (XRD) measurements indicate the enhancement of the crystal quality of films after annealing. There is a noticeable change and improvement in coated NiOTFs with heat treatment at 300 and 600 ℃ due to clear shifts in density. During the heating temperature increment, the energy of the band gap was shifted from 3.63 to 3.44 eV, and the electrical resistance of the NiOTFs varied from 1020 to 700 Ω-cm. Furthermore, the results indicate that the low-cost sol-gel (SG) deposition technique has a greater potential for producing high-quality p-type NiOTFs with minimal defects for electronic device applications.

Field-assisted sintering of barium titanate and 45S5 bioactive glass for biomedical applications

The development of electrically active biomaterials, which create electrical cues on demand to foster cellular stimulation, remains a challenge. Here, we utilized a Field-assisted sintering approach to densify barium titanate and 45S5 bioactive glass to create a piezoelectric and potentially bioactive composite. By using Field-assisted sintering, we aimed to fabricate dense piezoelectric specimens, preserving a low degree of crystallization of the bioactive glass to keep bioactivity as high as possible. Therefore, we have varied the compositions of the materials and processed them at different sintering temperatures. This enabled us to produce dense test specimens in the 94 %–98 % relative density range. The samples were successfully polarized, and piezoelectric charge constants d33 were determined for the composites. The content of bioactive glass and the sintering temperature influence the charge constant d33. It is in the range of 0.8–3.4 pC/N for the composites, approximately in the order of magnitude assigned to natural tissues such as bone. X-ray diffraction was used to analyze the composition of the processed samples and to investigate the influence of an additional thermal post-treatment. Altogether, we established a process window for field-assisted sintering, allowing the fabrication of a piezoelectric and potentially bioactive biomaterial for tissue engineering.

Nanostructural modulation of Schottky barrier in Au/α-MoO3 heterojunction via Au nanoparticle size control

Metal-semiconductor systems, particularly those incorporating metallic nanoparticles, have garnered significant attention due to their charge transport properties and potential in solid-state applications. Thus, this study focuses on the synthesis of MoO3 microstructures through thermal oxidation, followed by the synthesis of gold nanoparticles (AuNPs) via post-thermal treatment of an Au-coated film. We systematically investigated the effect of annealing temperatures ranging from 400 °C to 700 °C on the size of the AuNPs. Utilizing techniques such as X-ray diffraction, electron microscopy, reflectance, and X-ray photoelectron spectroscopy (XPS), the physical and chemical properties of the AuNPs/MoO3 heterojunction were characterized. Findings reveal a direct correlation between the size of AuNPs and the Schottky barrier height (SBH) in the Au/MoO3 system. By considering factors such as defects, impurities, lattice mismatch, and Au diffusion—referred to as the alpha adjustment—we established that smaller AuNPs foster lower SBH values in the heterostructures. The adjusted SBH for AuNPs with diameters of 81.90 nm ± 7.21 nm, 99.44 nm ± 9.47 nm, 134.96 nm ± 15.40 nm, and 459.99 nm ± 42.63 nm resulted in a value of 0.2 eV, 0.37 eV, 1.26 eV, and 3.61 eV, respectively.

Moderate thermal post-treatment of digestate to improve biomethane production from agricultural- and food waste

The aim of this study was to assess the feasibility of moderate thermal treatment (70 °C for one hour) of digestate in combination with post-digestion targeting residual biomethane potentials from three full-scale biogas plants digesting food waste (FW), agricultural waste (AW) and a mixture of AW and manure (AWM). Dissolved organic carbon (DOC), biomethane production, and digestate quality were investigated. For the study six laboratory-scale continuously stirred tank biogas reactors working as post-digesters, with thermally-treated and non-treated digestate were used. DOC for thermally-treated digestates increased significantly (t-test, p < 0.05); FW-digestate (110–200 %), AW-digestate (24–92 %) and for AWM-digestate (4–73 %). Indexes for corresponding DOC quality showed lower apparent organic molecular weights and decreased aromaticity (with the exception of FW-digestate). Thermal treatment of digestate improved the biomethane production during post-digestion by 21–22 % (FW-digestate) and 9 % (AW-digestate). For AMW-digestate no clear positive effect was observed, most likely due to biogas plant operational process disturbances.

Machine learning-guided accelerated discovery of structure-property correlations in lean magnesium alloys for biomedical applications

Magnesium alloys are emerging as promising alternatives to traditional orthopedic implant materials thanks to their biodegradability, biocompatibility, and impressive mechanical characteristics. However, their rapid in-vivo degradation presents challenges, notably in upholding mechanical integrity over time. This study investigates the impact of high-temperature thermal processing on the mechanical and degradation attributes of a lean Mg-Zn-Ca-Mn alloy, ZX10. Utilizing rapid, cost-efficient characterization methods like X-ray diffraction and optical microscopy, we swiftly examine microstructural changes post-thermal treatment. Employing Pearson correlation coefficient analysis, we unveil the relationship between microstructural properties and critical targets (properties): hardness and corrosion resistance. Additionally, leveraging the least absolute shrinkage and selection operator (LASSO), we pinpoint the dominant microstructural factors among closely correlated variables. Our findings underscore the significant role of grain size refinement in strengthening and the predominance of the ternary Ca2Mg6Zn3 phase in corrosion behavior. This suggests that achieving an optimal blend of strength and corrosion resistance is attainable through fine grains and reduced concentration of ternary phases. This thorough investigation furnishes valuable insights into the intricate interplay of processing, structure, and properties in magnesium alloys, thereby advancing the development of superior biodegradable implant materials.

Continuous wave laser-assisted evaporation of halide perovskite thin films from a single stoichiometric source

We report continuous wave laser-assisted evaporation (CLE), a thin film deposition technique that yields phase-pure and stoichiometric thin films of halide perovskites (HaPs) from stoichiometric HaP targets. We use methylammonium lead bromide (MAPbBr3) to demonstrate the ability to grow with CLE well-oriented and smooth thin films on various substrates. Further, we show the broader applicability of CLE by preparing films of several other 3D HaP compounds, viz., methylammonium lead iodide, formamidinium lead bromide, and a 2D one, butylammonium lead iodide. CLE is a single-source, solvent-free, room-temperature process that needs only roughing pump vacuum; it allows the deposition of hybrid organic-inorganic compound films without needing post-thermal treatment or an additional organic precursor source to yield the intended product. The resulting films are polycrystalline and highly oriented. All these features, and the fact that one stoichiometric source serves as the target, make for an attractive, potentially scalable dry deposition approach.

Fabrication of CNT-N@Manganese Oxide Hybrid Nanomaterials through a Versatile One-Pot Eco-Friendly Route toward Engineered Textile Supercapacitors.

The expansion of the Internet of Things market and the proliferation of wearable technologies have generated a significant demand for textile-based energy storage systems. This work reports the engineered design of hybrid electrode nanomaterials of N-doped carbon nanotubes (CNT-N) functionalized with two types of manganese oxides (MOs)-birnessite (MnO2) and hausmannite (Mn3O4)-and their application in solid-state textile-based hybrid supercapacitors (SCs). A versatile citric acid-mediated eco-friendly one-pot aqueous precipitation process is proposed for the fabrication of the hybrids. Remarkably, different types of MOs were obtained by simply changing the reaction temperature from room temperature to 100 °C, without any post-thermal treatment. Asymmetric textile SCs were developed using cotton fabrics coated with CNT-N and the hybrids as textile electrodes, and poly(vinyl) alcohol/orthophosphoric acid as the solid-gel electrolyte. The asymmetric devices presented enhanced energy storage performance relative to the symmetric device based on CNT-N and excellent cycling stability (>96%) after 8000 charge/discharge cycles owing to synergistic effects between CNT-N and the MOs, which endowed nonfaradaic and pseudocapacitive features to the SCs. The asymmetric SC based on CNT-N@MnO2 featured 47% higher energy density and comparable power density to the symmetric CNT-N-based device (8.70 W h cm-2 at 309.01 μW cm-2 vs. 5.93 W h cm-2 at 346.58 μW cm-2). The engineered hybrid CNT-N@MO nanomaterials and the eco-friendly citric acid-assisted one-pot precipitation route open promising prospects not only for energy storage, but also for (photo)(electro)catalysis, wastewater treatment, and (bio)sensing.

Adhesive properties of deposited Cu films on colorless polyimide using high power impulse magnetron sputtering system

This study explores the deposition of copper (Cu) films onto colorless polyimides (PIs) using the High Power Impulse Magnetron Sputtering (HiPIMS) technique. The impact of varying operating duty cycles and frequencies on sheet resistance, the deposition rate of Cu films, and the adhesion strength between Cu and PI is examined. Adjusting the HiPIMS parameters aims to achieve superior film quality with reduced sheet resistance. Furthermore, post-thermal treatment significantly improves the adhesion of the Cu layer to the PI substrate due to the mechanical interlocking mechanism created by the surface roughness of the PI and the chemical bonding between the two components.

The role of thermal cycling in micro-cracking development and flow alteration: Advanced insights from CT and lab studies

The recent interest in geothermal energy, nuclear waste management, and coal gasification has led to an in-depth examination of how granite rock behaves under subterranean reservoir conditions. Our research delves into the intricate microstructural and fluid dynamics of the Australian Harcourt granite. We emphasize its reactions to repeated temperature changes, cycling between 25 and 900 °C over 1–15 cooling episodes. To achieve this, we utilised X-ray computed tomography (CT) to visualize and reconstruct the heat-treated samples. Subsequently, we measured the porosity, identifying both total and directly interconnected spaces within these samples post-thermal treatment. Using avizo 2021.2, we created a pore network model (PNM) based on the connected porosity data to shed light on how fluids move through these heat-affected samples.The data highlighted that total porosity stayed below 0.5% up to 500 °C, with no directly connected porous regions detected. However, beyond this temperature, interconnected porosity began to appear, intensifying with increasing temperatures and more cooling cycles. The PNM allowed us to visualize and quantify specific details like pore and throat dimensions, their volumes, their interconnectedness, and the lengths of their connecting channels. Notably, these properties became more pronounced with escalating temperatures and cooling episodes, largely because of the fractures caused by the heat. Furthermore, we used AVIZO to analyse the absolute permeability of the heat-treated samples, providing a detailed understanding of their permeation characteristics. We also ran a set of rigorous lab tests to assess the impact of both confining pressure (ranging from 10 MPa to 40 MPa) and temperature (from 22 to 250 °C) on the fluid movement in the heat-treated rock. The experiments confirmed that increasing confining pressure non-linearly decreased Darcy's permeability. A rise in temperature further reduced permeability, mainly due to the narrowing of flow channels from mechanical and thermal stresses.Overall, the study provides a holistic understanding of porosity evolution and the subsequent fluid movement within thermally quenched rock samples under various reservoir conditions, providing valuable insights for energy and waste management applications.

Micro-fabrication of glassy carbon with low shrinkage and high char yield using high-performance photocurable phthalonitrile (PN) resins

Glassy carbons (GCs) are a significant class of materials that have attracted considerable attention in many scientific and technical fields due to their great thermal and chemical stability, excellent biocompatibility, and remarkable thermal and electrical conductivity. However, the thermal resistance and brittle nature of GCs pose limitations on their processing using conventional techniques such as melting extrusion or sintering. 3D printing as a rapidly developing technology advances product fabrication in prototyping and tooling provides a revolutionizing alternative of material processing with the advantage of accurately producing complex structures/shapes. This study demonstrates the micro-fabrication of GC objects based on novel photocurable high-performance phthalonitrile (PN) resins with a vat photopolymerization printing technology named as projection micro stereolithography (PμSL). In initial, soluble acrylate PN monomers are successfully developed and subsequently formulated into photopolymerizable resins. The resultant resins show excellent thermal and mechanical properties with Tg around 300 °C and flexural strength of 150 MPa after post thermal treatment. Being fabricated into 3D structures via PμSL printing, the obtained PN based objects are converted to GC products through pyrolysis in inert atmosphere with high char yield and low shrinkage. As a result, diverse microscale 3D GC objects are achievable and exhibit excellent structural integrity and fidelity. Our approach develops the micro-fabrication of dense and complex structured GC for the first time, providing a versatile functional platform for advancing next generation applications in medical tools, electrochemistry and precision micro-moulding as well as in energy and aerospace technologies.

Photoconductive TiO2 Dielectrics Prepared by Plasma Spraying

Titanium dioxide coatings (TiO2) were sprayed using a water-stabilized plasma gun (WSP) to form robust self-supporting bodies with the character of a ceramic disc capacitor (CDC). Agglomerated nanometric powder was used as feedstock. Argon was applied for powder feeding as well as coating–cooling to minimize the influence of ambient air. Stainless steel was used as a substrate, and the coatings were released after cooling. A more than three-millimeter-thick self-supporting TiO2 plate was observed using HR-TEM and SEM. Porosity was studied by image analysis on polished sections. Thermal post-treatment on the coating was conducted at a rather low temperature of 500 °C. The results of the subsequent dielectric measurement showed high permittivity, but this was strongly frequency-dependent and accompanied by a progressively decreasing loss tangent. On the other hand, the plasma-sprayed TiO2 exhibited persistent DC photoconductivity under and after illumination with a standard bulb.

Boosting Oxygen Reduction Reaction with Fe-Based Single-Atom Catalysts: The Role of Cluster Interactions

Fuel cells (FCs) have emerged as a promising alternative for efficient electricity production in the future [1]. However, their widespread commercialization is hindered by their prohibitive cost due to the large amount of platinum used in these electrochemical systems [2]. Platinum is used to accelerate the unfavorable kinetics of the cathodic oxygen reduction reaction (ORR) [3]. To achieve large-scale and cost-effective development of FCs, it is essential to find high-performance platinum-free catalysts. Two solutions are mainly reported in the literature: the development of non-precious metal-based carbon catalysts and metal-free carbon catalysts. However, the work reported on these two types of carbon catalysts is sometimes contradictory regarding the actual nature of the active sites and the mechanisms of reduction of oxygen molecules on the catalyst [4].Pyrolyzed metal-nitrogen-carbon (M-N-C) catalysts for the ORR, especially single-atom catalysts (SACs), have been widely studied because they exhibit excellent electrocatalytic performance, thanks to the high content of metal atoms anchored on a carbon support [5]. Recent research has indicated that the combination of single-atom active sites with metal nanoclusters can further improve the catalytic activity, but the underlying mechanism remains unclear [6]. Therefore, it is necessary to develop model catalysts based on both single-atoms and nanoclusters to better understand their catalytic activity.In this work, we prepared nitrogen-doped and iron-doped carbon catalysts (called Fe-NC below) with precise control of the type of iron in the material. First, the functionalization of an activated carbon was performed by carbonizing it under air in the presence of urea. Then, the sample was placed in an autoclave for hydrothermal treatment in the presence of FeCl3.6H2O to allow the incorporation of iron, and thermal post-treatment was applied to synthesize model catalysts (Fig. 1a). The precursor ratio and final pyrolysis temperature were adjusted and optimized to produce either iron-based single atoms (SA) (here referred to as FeSA-NC) or atomic clusters (AC) associated with single atoms (here referred to as FeSA+AC-NC). The results show that the iron-based catalysts exhibit outstanding catalytic activity (Fig. 1b) and durability (Fig. 1c) in alkaline medium for the ORR, even better than commercial Pt (20 wt.%)/C in the case of FeSA+AC-NC. The analysis provided insight into the development of highly efficient multifunctional electrocatalysts, where the presence of iron nanoclusters was found to be a crucial determinant of the catalytic activity for the ORR.[1] M.K. Debe, Electrocatalyst approaches and challenges for automotive fuel cells, Nature. 486 (2012) 43–51. https://doi.org/10.1038/nature11115.[2] C. Sealy, The problem with platinum, Mater. Today. 11 (2008) 65–68. https://doi.org/10.1016/S1369-7021(08)70254-2.[3] M. Borghei, J. Lehtonen, L. Liu, O.J. Rojas, Advanced Biomass-Derived Electrocatalysts for the Oxygen Reduction Reaction, Adv. Mater. 30 (2018) 1703691. https://doi.org/10.1002/adma.201703691.[4] A. Dessalle, J. Quílez-Bermejo, V. Fierro, F. Xu, A. Celzard, Recent progress in the development of efficient biomass-based ORR electrocatalysts, Carbon. 203 (2023) 237–260. https://doi.org/10.1016/j.carbon.2022.11.073.[5] K. Liu, J. Fu, Y. Lin, T. Luo, G. Ni, H. Li, et al., Insights into the activity of single-atom Fe-N-C catalysts for oxygen reduction reaction, Nat. Commun. 13 (2022) 2075. https://doi.org/10.1038/s41467-022-29797-1.[6] X. Wan, Q. Liu, J. Liu, S. Liu, X. Liu, L. Zheng, et al., Iron atom–cluster interactions increase activity and improve durability in Fe–N–C fuel cells, Nat. Commun. 13 (2022) 2963. https://doi.org/10.1038/s41467-022-30702-z. Figure 1

Local Heating Induced Single-Crystalline Phase Control in Electrochemical Synthesis of Nanomaterials

Synthesis of electrochemical crystalline nanomaterials have a great advantage. The single crystalline material synthesized by the existing solvothermal synthesis method often has no catalytic activity due to contamination on the surface during the synthesis process. Therefore, in this study, the electrochemical single crystalline nanomaterials induced by heat were clearly synthesized. Since a process of thermal post-treatment of nanomaterials require a high temperature, thermal induced electrochemical synthesis was lowering the thermal energy barrier.In this study, copper, silver, gold, and platinum single crystalline nanoparticles were synthesized and characterized through SEM, TEM, and SAED. In the synthesis process, the growth process according to deposition coulomb was observed. And the catalytic activity of the synthesized single crystalline nanomaterials was measured.

Laser direct writing of efficient 3D TiO2 nano-photocatalysts

The increasing demand for functional nanodevices in sustainable energy applications necessitates the development of innovative approaches. In this study, we present the fabrication and characterization of three-dimensional (3D) structures coated with titanium dioxide (TiO2) nanorods (NRs). These novel devices are created through the integration of four distinct techniques, multi-photon lithography, post-thermal treatment, pulsed laser deposition, and an aqueous chemical growth, enabling their unique properties and functionalities in photocatalysis. The photocatalytic performance of the 3D devices is evaluated through the degradation of organic pollutants, such as methylene blue and stearic acid, showcasing their efficiency in reducing pollutant concentrations. The devices demonstrate a remarkable decomposition coefficient (k=0.059min−1), highlighting their enhanced photocatalytic efficiency. Additionally, we propose a rapid fabrication technique using 3D holographic printing to create large-area TiO2-coated micro-structured photocatalytic devices at the mesoscale regime. This approach increases the active surface area, further enhancing the devices’ photocatalytic capabilities. By combining additive micro-manufacturing, TiO2 NR coating, and holographic printing, our work introduces a promising avenue for the development of advanced nanodevices with superior photocatalytic performance in sustainable energy applications.