Post-column Chemiluminescence Detection Research Articles

Programmable Low-Pressure Chromatographic Sub-90 s Assay of Parabens in Cosmetics with Post-Column Chemiluminescence Detection

This work describes a new programmable low-pressure chromatography method with post-column chemiluminescence (CL) detection for the rapid and cost-effective determination of four parabens in cosmetic products. Elution of the target analytes was achieved using a programmable mobile phase prepared by implementing a linear solvent gradient protocol based on appropriate flow rate modulation of 2 MilliGAT pumps. A 5 mm monolithic C18 column was used to separate the parabens. Post-column reaction of the eluted parabens with an acidic Ce(IV)-rhodamine 6G (Rho 6G) medium was carried out by introducing a flow stream of the reactants into the column eluate. The light generated from the CL reaction was detected with a flow-through CL detector fabricated in-house. The whole sequence of operations (including sample injection, generation of the mobile phase, addition of the post-column reaction reagents and signal acquisition) was under full computer control. Various operational parameters (the mobile phase composition and gradient conditions, the CL reagents’ concentrations and flow rates and the length of the reaction coil) were studied. The method was validated and applied to the analysis of various cosmetic products. The proposed approach allows sub-90 s separation of the four parabens and their determination with a limit of quantification of 0.2 μg L−1 with a sample throughput of 24 samples h−1. In addition, the method is economical, makes use of low-cost low-pressure components, is fully automated and produces a low amount of waste.

On-Line HPLC with Biochemical Detection for Screening Bioactive Compounds in Complex Matrixes

On-line high-performance liquid chromatography (HPLC) coupled with biochemical detection (BCD) has been developed to screen compounds showing antioxidant action, enzyme inhibition and receptor affinity in complex matrixes. This review summarizes HPLC methods combining different post-column detection methods, such as diode-array detection (DAD), mass spectrometry (MS), chemiluminescence (CL) and nuclear magnetic resonance, for antioxidant screening. The methods based on a single relatively stable reagent such as DPPH• and ABTS•+ were the most popular. Oxygen free radical scavengers mainly depended on post-column CL detection. The on-line hyphenated HPLC–BCD systems based on post-column UV/DAD fluorescence and MS detection were also widely applied to screen enzyme- and receptor-active compounds. These strategies provide a convenient tool for quick identification and quantification of active compounds in complex matrixes.

Stable Tris(2,2′-bipyridine)ruthenium(III) for Chemiluminescence Detection

Two exceedingly stable [Ru(bipy)(3)](3+) reagents were prepared by dissolving either [Ru(bipy)(3)](ClO(4))(2) in acetonitrile (containing 0.05 M HClO(4)) or [Ru(bipy)(3)]Cl(2)·6H(2)O in 95:5 glacial acetic acid-acetic anhydride (containing 0.05 M H(2)SO(4)) followed by oxidation with PbO(2). These conveniently prepared solutions provide highly reproducible chemiluminescence detection over long periods of analysis, avoiding the need for recalibration or preparation of fresh reagent solutions and without the complications associated with online chemical or electrochemical oxidations. The reagent prepared in acetonitrile produced much greater signal intensities with a range of analytes and was deemed most suitable for high-performance liquid chromatography (HPLC) with postcolumn chemiluminescence detection.

Multisyringe ion chromatography with chemiluminescence detection for the determination of oxalate in beer and urine samples

The first multisyringe-based low-pressure ion chromatographic method is presented. It is based on the use of short surfactant coated octadecyl-silica monolithic columns. As a first application, we have determined oxalate in beer and human urine via post-column chemiluminescence detection. Oxalate is separated from the sample matrix in the monolithic column by precise programmable fluid handling, and then detected by reaction with on-line generated tris(2,2′-bipyridyl)ruthenium(III). Column coating, un-coating, ion chromatography and chemiluminescence detection are quickly performed by using a simple low-pressure multi-burette. The factors influencing the separation of oxalate and its subsequent detection, including the column coating with surfactants and its stability have been studied. The chromatographic behavior of the oxalate in presence of potentially interfering species also was assessed. The method has limits of detection and quantification of 0.025 and 0.035 mg L−1, respectively, a relative standard deviation of 3.1% (for 10 consecutive measurements without column re-coating) and a throughput of 48 h−1. The results obtained with real samples were validated by using an enzymatic spectrophotometric test. The method is critically compared to recent methods for the determination of oxalate.

Determination of N-methylcarbamate pesticides in water and vegetable samples by HPLC with post-column chemiluminescence detection using the luminol reaction

In this paper we proposed a reverse high performance liquid chromatography method for the simultaneous determination of three N-methylcarbamates (NMCs) named carbofuran, carbaryl and methiocarb, using the post-column chemiluminescence (CL) detection with the luminol reaction. This method is based on the enhancing effect of these analytes on the CL emission generated by the oxidation of luminol with potassium permanganate in alkaline medium. The separation was reached in less than 14 min using a C18 column and an isocratic binary mobile phase consisting of acetonitrile:water (50:50, v/v) pumped at a flow rate of 1 mL min(-1). CL reagents (luminol and KMnO(4)) were incorporated by means of a peristaltic pump and were firstly mixed using a three-way connector. Then this stream was mixed with the eluate using another three-way connector just before reaching the detection cell. The optimization of variables affecting the CL reaction (reaction medium, concentration, flow rate of reagents and distance between both connectors) were optimized by means of experimental designs. Ethiofencarb, a NMC which has nowadays fallen into disuse was used as internal standard. For the analysis of theses pesticides in real water samples a pre-treatment step consisting of solid phase extraction (SPE) was conducted in order to reach sensitivity levels below the legal maximum concentration permitted. In the case of vegetable sample, SPE was used for matrix cleaning purpose.

Dye-sensitized phototransformation of chlorophenols and their subsequent chemiluminescence reactions

Abstract A novel chemiluminescence (CL) reaction of chlorophenols (CPs), including 2-chlorophenol (2-CP), 4-CP, 2,4-dichlorophenol (2,4-DCP), 2,4,6-trichlorophenol (2,4,6-TCP) and pentachlorophenol (PCP) was reported, which was based on the oxidation of the phototransformed CPs by N-bromosuccinimide (NBS). It was found that the dye-sensitized phototransformation is a prerequisite for the subsequent CL reaction, and the presence of 1.9×10–2 mol L−1 Triton X-100 or 3.7×10–3 mol L−1 CTAB can greatly enhance the CL intensity. A neutral sample solution with the presence of 2×10–5 mol L−1 fluorescein (FL) was found to be optimum for the phototransformation of 2-CP, 4-CP, 2,4-DCP and PCP, but a lower pH of 5.3 was more suitable for 2,4,6-TCP. Based on the CL reaction, detection limits of 8.6×10−8, 1.1×10−7, 1.5×10–7, 4.6×10–8 and 3.0×10−5 mol L−1 were achieved, respectively, for 2-CP, 4-CP, 2,4-DCP, 2,4,6-TCP and PCP with the optimized conditions in the flow system. The mechanism of the phototransformation and the subsequent CL reaction were preliminarily studied and it was suggested that the singlet oxygen formed in the dye-sensitization process was responsible for the conversion of CPs into light-emitting precursors. These intermediate products were suggested to be peroxide compounds after testing by a luminal-based post-column CL detection experiment.

Determination of propylthiouracil and methylthiouracil in human serum using high-performance liquid chromatography with chemiluminescence detection

Based on the sensitizing effect of formaldehyde on the chemiluminescence (CL) reaction of propylthiouracil (PTU) and methylthiouracil (MTU) with acidic potassium permanganate and the combination technique of high-performance liquid chromatography (HPLC), a sensitive, selective and simple post-column CL detection method for determining PTU and MTU is described. The optimal conditions for the CL detection and HPLC separation were carried out. The linear ranges were 0.1-20 microg mL(-1) for MTU and 0.1-10 microg mL(-1) for PTU, the detection limits were 0.03 microg mL(-1) for PTU, 0.03 microg mL(-1) for MTU and the quantification limits were 0.1 microg mL(-1) for PTU, 0.1 microg mL(-1) for MTU. The method has been satisfactorily applied for the determination of MTU and PTU in human serum samples.

The Determination of Morphine in the Larvae of Calliphora stygia using Flow Injection Analysis and HPLC with Chemiluminescence Detection

Selective determination of morphine in the larvae of Calliphora stygia (Fabricius) (Diptera: Calliphoridae) using acidic potassium permanganate chemiluminescence detection coupled with flow injection analysis and high-performance liquid chromatography (HPLC) is described. Larvae of C. stygia were reared on minced meat substrates that had been spiked with varying concentrations of morphine. Morphine concentrations were chosen to reflect typical levels in human tissues from opiate overdose victims. After maturing on substrates, larvae were analyzed for the presence of morphine using chemiluminescence detection coupled to flow injection analysis and a rapid HPLC method. Analysis of the larval matrix by flow injection analysis with chemiluminescence detection indicated the presence of interferants capable of generating chemiluminescence. A rapid chromatographic separation with a monolithic column allowed selective determination of morphine in larvae using postcolumn chemiluminescence detection. Larvae of C. stygia reared on substrates containing morphine at concentrations of 500 and 1000 ng/g did not sequester morphine at detectable concentrations. Larvae reared on substrates containing morphine concentrations of 2500, 5000, and 10,000 ng/g tested positive for the drug at concentrations of 765, 2720, and 3010 ng/g, respectively.

Determination of phenothiazines in pharmaceutical formulations and human urine using capillary electrophoresis with chemiluminescence detection

A CE instrument coupled with chemiluminescence (CL) detection was designed for the determination of promethazine hydrochloride (PTH) and promazine hydrochloride (PMH) in real samples. An important enhancement of the CL emission of luminol with potassium ferricyanide was observed in the presence of these phenothiazines; so this system was selected for their detection after CE separation. Parameters affecting the electrophoretic separation were optimized in a univariate way, while those affecting CL detection were optimized by means of a multivariate approach based on the use of experimental designs. Chemometrics was also employed for the study of the robustness of the factors influencing the postcolumn CL detection. The method allows the separation of the phenothiazines in less than 4 min, achieving LODs of 80 ng/mL for PMH and 334 ng/mL for PTH, using sample injection by gravity. Electrokinetic injection was used to obtain lower LODs for the determination of the compounds in biological samples. The applicability of the CE-CL method was illustrated in the determination of PTH in pharmaceutical formulations and in the analysis of PMH in human urine, using a previous SPE procedure, achieving an LOD of 1 ng/mL and recoveries higher than 85%.

The Determination of Psilocin and Psilocybin in Hallucinogenic Mushrooms by HPLC Utilizing a Dual Reagent Acidic Potassium Permanganate and Tris(2,2′‐bipyridyl)ruthenium(II) Chemiluminescence Detection System

This paper describes a procedure for the determination of psilocin and psilocybin in mushroom extracts using high-performance liquid chromatography with postcolumn chemiluminescence detection. A number of extraction methods for psilocin and psilocybin in hallucinogenic mushrooms were investigated, with a simple methanolic extraction being found to be most effective. Psilocin and psilocybin were extracted from a variety of hallucinogenic mushrooms using methanol. The analytes were separated on a C12 column using a (95:5% v/v) methanol:10 mM ammonium formate, pH 3.5 mobile phase with a run time of 5 min. Detection was realized through a dual reagent chemiluminescence detection system of acidic potassium permanganate and tris(2,2'-bipyridyl)ruthenium(II). The chemiluminescence detection system gave improved detectability when compared with UV absorption at 269 nm, with detection limits of 1.2 x 10(-8) and 3.5 x 10(-9) mol/L being obtained for psilocin and psilocybin, respectively. The procedure was applied to the determination of psilocin and psilocybin in three Australian species of hallucinogenic mushroom.

Post-column detection of benzenediols and 1,2,4-benzenetriol based on acidic potassium permanganate chemiluminescence

Based on the sensitizing effect of formic acid on the chemiluminescence (CL) reaction of polyhydroxylbenzenes with acidified potassium permanganate and the combination technique of high-performance liquid chromatography (HPLC), a sensitive, selective and simple post-column CL detection method for simultaneously determining catechol, resorcinol, hydroquinone and 1,2,4-benzenetriol is described. The optimal conditions for the CL detection and HPLC separation were carried out. The linear ranges were: 6.0 x 10(-3)-1.5 mg/L for hydroquinone, 8.0 x 10(-3)-1.5 mg/L for 1,2,4-benzenetriol, 1.0 x 10(-2)-2.0 mg/L for resorcinol and 1.0 x 10(-2)-2.5 mg/L for catechol, respectively. The detection limits are: 3.2 x 10(-3) mg/L for hydroquinone, 3.9 x 10(-3) mg/L for 1,2,4-benzenetriol, 4.7 x 10(-3) mg/L for resorcinol and 5.2 x 10(-3) mg/L for catechol, respectively. Combining with solid phase extraction, the proposed method has been successfully applied to the determination of the polyhydroxylbenzenes in river water. The recoveries for three benzentriols were 92.1-95.4% and 82.0% for 1,2,4-benzenetriol, respectively.

Optimization and development of a high-performance liquid chromatography-based one-site immunometric assay with chemiluminescence detection

Abstract Various practical and theoretical considerations were examined in the creation and optimization of a high-performance liquid chromatography (HPLC)-based one-site immunometric assay. This method used an HPLC analyte analog column and post-column chemiluminescence detection. The specific analyte chosen as the model for this study was l -thyroxine (also known as T 4 ). In this technique, a sample containing thyroxine was first combined with an excess of anti-T 4 antibody Fab fragments that had earlier been conjugated with chemiluminescent acridinium ester labels. After incubation, the mixture was injected onto a column that contained immobilized T 4 . The amount of thyroxine in the original sample was then determined by measuring the labeled Fab fragments that appeared in the non-retained fraction, or the decrease in excess Fab fragments that were bound to and later eluted from the column. Items considered in creating this assay included the preparation of acridinium ester-labeled Fab fragments, the detection of these fragments with a post-column reactor, and the creation of a suitable immobilized analog column for capturing excess labeled Fab fragments. The final method could measure T 4 in standards at clinically-relevant concentrations and provided a response within 1.5 min of sample injection, following a 20–45 min incubation with the labeled Fab fragments. Possible applications of this method include its use in clinical chemistry and the screening of proteomic or combinatorial libraries.

Antioxidant defenses in rat intestine and mesenteric lymph

Dietary oxysterols can reach the circulation and this may contribute to atherosclerosis, where lipid oxidation is thought to be important. There is also evidence that, in rats,peroxidized lipids are absorbed and transported into lymph [Aw TY, Williams MW, Gray L. Absorption and lymphatic transport of peroxidized lipids by rat small intestine in vivo: role of mucosal GSH. Am J Physiol 1992; 262: G99–G106], although the method used to detect lipid peroxides lacked specificity. We tested whether intragastric administration of vegetable oils containing triglyceride hydroperoxides (TG-OOH) to rats resulted in detectable lipid hydroperoxides in mesenteric lymph. Using sensitive HPLC with postcolumn chemiluminescence detection, we were unable to detect hydroperoxides of triglycerides, cholesterylesters or phospholipids during the course of lipid absorption, and lymph levels of ascorbate, urate, α-tocopherol and ubiquinol-9 did not change significantly. By contrast, we observed a striking reducing activity judged by the efficient reduction of administered ubiquinones-9 and -10 to the corresponding ubiquinols. Exposure of rat lymph and isolated chylomicrons to aqueous peroxyl radicals revealed patterns of antioxidant consumption and lipid hydroperoxide formation similar to those described previously for human extravascular fluids and isolated lipoproteins, respectively. In particular, rates of TG-OOH formation in lymph and chylomicrons were very low to undetectable as long as ascorbate and/or ubiquinols were present, but subsequently proceeded in a chain reaction despite the presence of α-tocopherol. These studies demonstrate that rat intestine and mesenteric lymph possess efficient antioxidant defenses against preformed lipid hydroperoxides and (peroxyl) radical mediated lipid oxidation. We conclude that dietary lipid hydroperoxides or postprandial oxidation of lipids are not likely to contribute to these particular forms of oxidized lipids in circulation and aortic tissue.

Determination of phospholipid oxidation in cultured cells

This chapter discusses the use of high-performance liquid chromatography (HPLC) with postcolumn chemiluminescence detection for the measurement of lipid peroxidation in cultured cells. In this assay, extracted phospholipids are separated by HPLC over a silica column and individual lipid classes are detected by UV (ultra violet) absorption. In the postcolumn chemiluminescence assay, microperoxidase catalyzes the decomposition of hydroperoxides to the corresponding alkoxyl radicals. This alkoxyl radical formation facilitates the oxidation and decomposition of isoluminol, yielding visible light that is maximal at a wavelength of 430 nm. This method has several advantages over the more common thiobarbituric acid (TBA) assay. Specifically, this assay measures the hydroperoxide groups directly, and it is less prone to interference such as is observed with the TBA assay. In addition, the assay can be adapted for individual identification of phospholipid hydroperoxides (PLOOHs) from the different phospholipid classes.

HPLC Band Shape Analysis for Postcolumn Chemiluminescence Detection Obtained by Finite-Difference Simulation: The Chemical Band Narrowing Effect

Algorithms for the finite-difference digital simulation of partition chromatography with chemiluminescence (CL) detection have been developed for a proposed postcolumn CL reaction mechanism for acridinium esters reacting with peroxide and base. These algorithms use classical plate theory to establish the theoretical chromatographic band shape; subsequently, statistical moment analysis is employed to evaluate the retention time and the variance for the “spectrophotometric” peak obtained prior to postcolumn reaction with peroxide and base and for the CL peak shape detected downstream. The resulting model can be used to compare the two band shapes and to optimize postcolumn CL detection conditions such as the concentration of peroxide and base and the length of tubing connecting reaction tee and detector. The simulation assesses the effect of each photochemical reaction involved in the CL mechanism on detection level and chromatographic efficiency. As such, this work provides fundamental insight into the eff...

Peroxyoxalate chemiluminescence detection for capillary electrophoresis using membrane collection

Capillary electrophoresis (CE) is often limited by the need to measure nanoliter-volume, low-concentration analytes with selectivity and specificity. A post-column chemiluminescence (CL) method is described in which the capillary effluent is collected on a membrane which has been coated with a peroxyoxalate CL reagent, bis(2,4,6-trichlorophenyl)oxalate. After the CE run, the CL reaction is initiated on the membrane by applying hydrogen peroxide, a scientific charge-coupled device (CCD) camera images the resultant CL emission, and an electropherogram is reconstructed. This postcolumn detection scheme decouples the separation parameters from detection and allows longer lived CL reagents to be used with fast separations. As the reaction is catalyzed by imidazole, CL intensities and lifetimes resulting from imidazole- and non-imidazole-running buffers are compared. The postcolumn CL method is compared to on-line UV absorbance detection for a mixture of dansylated amino acids, with limits of detection (LODs) of 1.5 μM (13 fmol) and separation efficiencies of 170,000 plates. The ability to preserve the sample on the membrane allows several selective detection schemes to be employed; the combination of postcolumn chemiluminescence and radionuclide detection from a single electrophoretic separation is demonstrated. © 1998 John Wiley & Sons, Inc. J Micro Sep 10: 329–337, 1998

Optimization of post-column chemiluminescent detection for low-molecular-mass conjugates of acridinium esters

In this study, various factors are examined that affect the post-column chemiluminescence detection of low-molecular-mass compounds labelled with acridinium esters, using 9-phenyl acridinium ester (PAE) as the initial model. Reaction conditions examined included the effect of hydroxide or hydrogen peroxide concentration, ionic strength and surfactant content on the degree and length of light production by the acridinium ester label. Based on these results, a system was developed for the post-column detection of acridinium ester conjugates in HPLC. The final post-column reactor had optimum conditions similar to those for a benchtop luminometer but gave light production over slightly longer periods of time and had a broader range of reagent concentrations that gave a maximum response. The detection limit of this system for PAE was 7 x 10(-19) mol per injection, with linear and dynamic ranges that extended up to 3 x 10(-15) and 3 x 10(-13) mol, respectively. Some preliminary work was conducted examining the use of this system in chromatography-based competitive binding immunoassays with a thyroxine-acridinium ester conjugate being used as the label. The estimated limit of detection was 2.5 x 10(-17) mol (or roughly 10(-12) M for a 25 microliters sample) based on the retained fraction of the conjugate.

Determination of inorganic anions in water samples by ion-exchange chromatography with chemiluminescence detection based on the neutralization reaction of nitric acid and potassium hydroxide

Abstract A faint chemiluminescence (CL) from the neutralization reaction of nitric acid and potassium hydroxide was enhanced by addition of iron(III) to the acid. The enhanced CL emission was suppressed by adding inorganic anions such as chloride, bromide, nitrite, nitrate and sulfate to the base. Based on the findings, a new post-column CL detection method was developed for the determination of the anions. Several kinds of anions were separated by anion-exchange chromatography using a potassium hydroxide solution as eluent. The effluent from the anion-exchange column was mixed with nitric acid containing iron(III) ions, and the CL was suppressed by the eluting anions. For each anion, linear calibration ranges extending from 100 ng ml −1 to 100 μg ml −1 were obtained. The relative standard deviations for five replicate measurements of 10 μg ml −1 were 1.3–4.3%. The present method was successfully applied to determine inorganic anions in water samples.

Oxidation of parenteral lipid emulsion by ambient and phototherapy lights: Potential toxicity of routine parenteral feeding

Vitamin E can be a prooxidant in isolated lipoprotein suspensions. Because lipid emulsions used in parenteral nutrition are lipoprotein-like suspensions rich in polyunsaturated fatty acids and vitamin E, we hypothesized that vitamin E may act as a prooxidant in lipid emulsions, as it is in lipoprotein suspensions. We therefore exposed an intravenously administered lipid emulsion (Intralipid) to a single spotlight commonly used in the treatment of neonatal jaundice, and measured the formation of triglyceride hydroperoxides by using high-performance liquid chromatography with postcolumn chemiluminescence detection. Concentrations of these hydroperoxides in different batches of fresh intralipid were usually approximately 10 mumol/L but increased up to 60 times after exposure to phototherapy light for a period of 24 hours, even though significant amounts of vitamin E were present at the end of the exposure. Triglyceride hydroperoxides were formed during phototherapy light exposure whether the intralipid was in plastic tubing used routinely for infusion or in glass containers. Ambient light also caused significant peroxidation of the formula lipids, although to a much lesser extent than observed with phototherapy light. For infants in the neonatal intensive care unit who were receiving intralipid but not phototherapy, solutions being infused at the end of 24 hours contained a mean of 40 mumol/L hydroperoxides. For infants receiving phototherapy, the mean was 97 mumol/L. Phototherapy light-induced formation of triglyceride hydroperoxides was prevented by covering the intralipid with aluminum foil or supplementation with sodium ascorbate before light exposure. We conclude that intralipid is highly susceptible to oxidation and that elevated levels of oxidized lipids can be formed during its clinical use, especially when intralipid infusion is combined with phototherapy. Because lipid hydroperoxides are cytotoxic and can cause adverse effects, inadvertent infusion of rancid intralipid may add to the numerous problems encountered by premature neonates.

Determination of oxalate in alumina process liquors by ion chromatography with post column chemiluminescence detection

The analysis of oxalate in Bayer liquor had been successfully demonstrated using a combination of ion-exchange chromatography and post-column detection based on a chemiluminescence reaction with tris(2-2′bipyridyl)ruthenium(III). Common interferences, including other dicarboxylic acids and inorganic anions, have been shown to elicit no significant response. The chemiluminescence response is linear and a detection limit of 10–7 mol l–1 possible. The potential use of this method for other complex samples is presented. Chromatographic conditions provide a rapid analysis with sample analysis possible every 5–8 min.