Portable Equipment Research Articles

Assessment of spray system capabilities in reduction of containment pressure and deposition of fission products during a severe accident in VVER-1000

In this study, we have investigated the spray system's capabilities to reduce fission products in the containment atmosphere and control the containment pressure in a VVER-1000 nuclear power plant. Large Break Loss of Coolant Accident (LB-LOCA) without access to the active part of the Emergency Core Cooling System (ECCS), as a worst-case severe accident, has been investigated as a case study. Only containment is simulated via the MELCOR code, while leakage of various materials from the nuclear power plant's core and the primary circuit is considered as the boundary conditions. Following the Fukushima accident in 2011, many nuclear safety regulatory organizations focused on using portable equipment that is essential for decay heat removal in nuclear power plants during severe accidents. Based on the literature studies, the accident management scenarios have changed recently since severe accidents inside nuclear power plants have worried many scientists and the public. Evaluating the current spray system in a severe condition based on which this system was not designed is vital and novel. We considered that the spray system would be fully restored and perform its safety function using the existing portable equipment to depressurize the containment and deposition of the fission products. To calculate the maximum allowed delay time of the spray system recovery, the accident was modeled without the operation of the spray system while a safety criterion was considered to avoid reaching the ultimate pressure of containment. For a more detailed evaluation of the spray system, two different operating modes including the activation of one spray train and the activation of both spray trains have been selected. According to the obtained results, if the spray system is revived before 4,000s from the beginning of the accident, this system would be able to reasonably mitigate the accident consequences. Moreover, without the need for any external water supply source for the spray system, this system can be permanently fed from the containment sump for at least 800,000s after the initiation of the accident, requiring the relevant heat exchanger of the spray system to be recovered for this period.

Optically Stimulated Luminescence in LiF–MgF2 system and its response as medical radiation dosimeter

Optically Stimulated Luminescence (OSL) based dosimeters are garnering attention in the field of radiation dosimetry due to a number of benefits like portable equipment, easy and efficient excitation and read out process, re-readability of the dose etc.. Though varieties of fluoroperovskites have been studied as OSL materials, no research on LiMgF3 (Lithium Magnesium Fluoride) as an OSL material has yet been conducted. In the current work, LiF–MgF2 system with a low effective atomic number was synthesized using the high temperature solid state reaction approach and its OSL dosimetry properties were investigated. The prepared sample was thoroughly characterized by employing a variety of techniques, such as X-ray diffraction (XRD), Scanning Electron Microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), and UV–Vis (ultraviolet–visible) spectrophotometry. The structure of the sample was found to be polycrystalline with size in the micrometre range. OSL properties of LMF have been investigated for different doses of gamma and beta along with related OSL kinetic parameters. It exhibits good dose linearity under blue stimulation for gamma (100 mGy - 700 Gy) and beta (30 mGy - 5Gy) radiation. We have also investigated the reusability (3%), reproducibility (2–3%), and fading (45% in 40 days) of the phosphor. To check the viability of the sample in radiation dosimetry under medical treatment in radiotherapy, various dosimetric properties were studied in Linear Accelerator (LINAC) x-rays in MV energy range and Cobalt-60 gamma radiation. These studies include the response of the phosphor to various energies (called energy dependence), field size effect, the effect of the dose rate of the radiation beam, and relative depth dose response. The overall response of the phosphor (comparable with ion chamber in RT experiments) makes the material a potential candidate to be used as an OSL phosphor in medical radiation dosimetry.

In Situ Growth of Ni-MOF Nanorods Array on Ti3C2Tx Nanosheets for Supercapacitive Electrodes.

For the energy supply of smart and portable equipment, high performance supercapacitor electrode materials are drawing more and more concerns. Conductive Ni-MOF is a class of materials with higher conductivity compared with traditional MOFs, but it continues to lack stability. Specifically, MXene (Ti3C2Tx) has been employed as an electrochemical substrate for its high mechanical stability and abundant active sites, which can be combined with MOFs to improve its electrochemical performance. In this paper, a novel Ni-MOF nanorods array/Ti3C2Tx nanocomposite was prepared via a facile hydrothermal reaction, which makes good use of the advantages of conductive Ni-MOF and high strength Ti3C2Tx. The high density forest-like Ni-MOF array in situ grown on the surface of Ti3C2Tx can provide abundant active electrochemical sites and construct a pathway for effective ion transport. The formation of a "Ti-O···Ni" bond accomplished during an in situ growth reaction endows the strong interfacial interaction between Ni-MOF and Ti3C2Tx. As a result, the Ni-MOF/Ti3C2Tx nanocomposite can achieve a high specific capacitance of 497.6 F·g-1 at 0.5 A·g-1 and remain over 66% of the initial capacitance when the current density increases five times. In addition, the influence of the Ti3C2Tx concentration and reaction time on the morphology and performance of the resultant products were also investigated, leading to a good understanding of the formation process of the nanocomposite and the electrochemical mechanism for a supercapacitive reaction.

Botanical honey recognition and quantitative mixture detection based on Raman spectroscopy and machine learning

The development of new approaches for honey recognition, based on spectroscopic techniques, presents a huge market potential especially because of the fast development of portable equipment. As an emerging approach, the association between Raman spectroscopy and Artificial Intelligence (i.e. Machine Learning algorithms) for food and beverages recognition starts to prove its efficiency, becoming an important candidate for the development of a practical application. Through this study, new recognition models for the rapid and efficient botanical differentiation of investigated honey varieties were developed, allowing the correct prediction of each type in a percentage better than 81%. The performances of the constructed models were expressed in terms of precision, sensitivity, and specificity. Moreover, through this approach, the detection of honey mixtures was possible to be made and an estimative percentage of the mixture components was obtained. Thus, the applicative potential of this new approach for honey recognition as well as a qualitative and quantitative estimation of the honey mixture was demonstrated.

Detection of Energetic Ions Based on Tapered Optical Fiber

Single-mode tapered optical fibers (TOF) are well-known for applications in sensing. In this work, we demonstrate the use of tapered optical fibers to detect charged particles (ions) irradiated at various energies, fluences, and species. In this experiment, two different ion species, namely, Ar+ and N+, have been used to irradiate tapered optical fibers at various fluences and energies. The variations in the free spectral range (FSR), period, and transmission power loss from the ion beam irradiated TOFs are picked up by the optical spectrum analyzer (OSA). We were able to identify ions with energy as low as 80 keV because of the change in the refractive index of the cladding material caused by the implanted ions. The observed changes in spectra are explained using the results of COMSOL simulations. Using Monte Carlo-based TRI3DYN ion–solid interaction simulation, the surface modification and defect formation caused by ion beams as well as the implantation profile in the TOF have been predicted. These results are further corroborated by experimental studies such as scanning electron microscopy and Raman scattering spectroscopy. Such a tapered optical fiber-based detection method will aid in the creation of portable equipment to identify charged particles in nuclear reactors and in space exploration.

Spatially Offset Raman Spectroscopic (SORS) Analysis of Wine Alcoholic Fermentation: A Preliminary Study

Spatially offset Raman spectroscopy (SORS) is a non-invasive analytical technique that allows the analysis of samples through a container. This makes it an effective tool for studying food and beverage products, as it can measure the sample without being affected by the packaging or the container. In this study, a portable SORS equipment was used for the first time to analyse the alcoholic fermentation process of white wine. Different sample measurement arrangements were tested in order to determine the most effective method for monitoring the fermentation process and predicting key oenological parameters. The best results were obtained when the sample was directly measured through the glass container in which the fermentation was occurring. This allowed for the accurate monitoring of the process and the prediction of density and pH with a root mean square error of cross-validation (RMSECV) of 0.0029 g·L−1 and 0.04, respectively, and R2 values of 0.993 and 0.961 for density and pH, respectively. Additionally, the sources of variability depending on the measurement arrangements were studied using ANOVA-Simultaneous Component Analysis (ASCA).

Performance Study of Portable Semiconductor Refrigeration Device Based on CFD Simulation.

Since the summer of 2022, the whole world has suffered the abnormal weather phenomena of high ambient temperature. Equipment for refrigeration, particularly portable refrigeration equipment, is crucial for personal protection in high-temperature environments, but cooling performance and miniaturization have been challenging issues. A portable air conditioner based on a semiconductor refrigeration device for human body cooling was developed. The total weight of the device is 450 g. The overall power consumption of the device is 82 W and the energy consumption ratio of semiconductor cooling plate is 0.85. The semiconductor refrigeration technology is based on the Peltier effect, supplemented by a DC fan to send the cooling air out to a specified position or zone. The structural parts are manufactured by 3D printing technology to make the overall size of the device more compact. The air volume and cooling performance of the device were analyzed by computational fluid dynamics simulation and the temperature distribution was measured by an infrared thermal imager and other instruments, and the measured results agreed with the CFD simulation results. The test ambient temperature was 20 °C. The measurement results showed that the wind speed of the hot air outlet was 6.92 m/s and that of the cold air outlet was 8.24 m/s. The cold air surface temperature reached a stable state of 13.9 °C in about 4 min, while the hot air surface temperature reached a stable state of 47.2 °C.

Optimizing forest canopy structure retrieval from smartphone‐based hemispherical photography

Abstract Hemispherical photography (HP) is a long‐standing tool for forest canopy characterization. Currently, there are low‐cost fisheye lenses to convert smartphones into highly portable HP equipment (smartphone‐based HP, hereafter SHP). However, there is an obstacle to having a close‐to‐ideal method for citizen science and large‐scale or opportunistic sampling: the known sensitivity of HP to illumination conditions. The purpose of this paper is to test a ready‐to‐use approach based on previous research and to contribute to quantifying the errors associated with choosing SHP in non‐recommended light conditions over well‐established HP practices. In 30 locations distributed in broadleaf and coniferous woodlands, a total of 1080 photographs were taken with two smartphone models, manipulating the exposure, and under varied sky conditions. After image binarization, accurate reference data was employed to evaluate the reliability of extracting canopy parameters from SHP. The proposed methodology can reliably quantify canopy openness (RMSE ~0.04) and plant area index (RMSE ~0.4). Results suggest that SHP, when used following the recommendations of the present study, allows retrieval of reliable canopy metrics independently of sky conditions and forest type.

OpenCare5G: O-RAN in Private Network for Digital Health Applications

Digital Health is a new way for medicine to work together with computer engineering and ICT to carry out tests and obtain reliable information about the health status of citizens in the most remote places in Brazil in near-real time, applying new technologies and digital tools in the process. InovaHC is the technological innovation core of the Clinics Hospital of the Faculty of Medicine of the University of São Paulo (HCFMUSP). It is the first national medical institution to seek new opportunities offered by 5G technology and test its application in the first private network for Digital Health in the largest hospital complex in Latin America through the OpenCare5G Project. This project uses an Open RAN concept and network disaggregation with lower costs than the traditional concept used by the telecommunications industry. The technological project connected to the 5G network was divided into two phases for proof-of-concept testing: the first with an initial focus on carrying out examinations with portable ultrasound equipment in different locations at HCFMUSP, and the second focusing on carrying out remote examinations with health professionals in other states of Brazil, who will be working in remote areas in other states with little or no ICT infrastructure together with a doctor analyzing exams in real time at HCFMUSP in São Paulo. The objective of the project is to evaluate the connectivity and capacity of the 5G private network in these the proof-of-concept tests for transmitting the volume of data from remote exams with higher speed and lower latency. We are in the first phase of the proof of concept testing to achieve the expected success. This project is a catalyst for innovation in health, connecting resources and entrepreneurs to generate solutions for the innovation ecosystem of organizations. It is coordinated by Deloitte with the participation of the Escola Politécnica da USP (The School of Engineering-University of São Paulo), Airspan, Itaú Bank, Siemens Healthineers, NEC, Telecom Infra Projet, ABDI and IDB. The use of 5G Open RAN technology in public health is concluded to be of extreme social, economic, and fundamental importance for HCFMUSP, citizens, and the development of health research to promote great positive impacts ranging from attracting investment in the country to improving the quality of patient care.

Advanced Strategies for Improving Lithium Storage Performance under Cryogenic Conditions

AbstractAs a vital technology in portable electronic equipment, electric vehicle, and stationary energy storage, lithium‐based batteries are currently gaining widespread attention. However, when batteries are used more frequently, there are greater worries regarding their susceptibility to temperature, especially at low temperatures (LTs). In this review, the factors that lead to capacity loss in lithium‐based batteries at LT are analyzed and a summary of the most recent cutting‐edge approaches for improving LT kinetics is provided. In order to achieve satisfactory LT performance, electrode technology, interface chemistry, and electrolyte engineering must be taken into account during the cell design process. The recently revealed unique cryogenic storage mode and design concepts are also thoroughly introduced in this review, which is intended to motivate researchers in related domains. Finally, new insights, intriguing concepts, and workable solutions are proposed to promote the ongoing development of high‐performance cryogenic lithium batteries.

Correlation of the DNA Concentration of Human Samples to Electrical Bioimpedance Measurements: A Pilot Study.

It is necessary to evaluate the total deoxyribonucleic acid (DNA) concentration in gene expression assays. The existing techniques require equipment that is expensive for many labs in developing countries. Portable and inexpensive equipment is needed for easy and economical DNA quantification. Electrical bioimpedance spectroscopy (EBiS) is a non-invasive and inexpensive technique for examining the electrical properties of biological materials. The aim of this study was to explore a potential correlation between the measurement of total DNA extracted from human samples by UV-Vis spectrophotometry and EBiS. Hence, after quantifying the total DNA extracted from each sample by UV-Vis spectroscopy, EBiS was recorded and a possible correlation between the two measurements was analyzed. Considering the bioimpedance phase parameter at 5.24 MHz, a significant correlation was found with total DNA, especially when the concentration was below 100 ng/μL (Spearman coefficient = 0.82, p<0.005). Additional experiments are warranted to confirm these findings.

Ultralight and Highly Conductive Silver Nanowire Aerogels for High-Performance Electromagnetic Interference Shielding.

Metal-based materials possess superior electromagnetic interference (EMI) shielding performance because of their extraordinary electrical conductivity. Nevertheless, the high density and structural rigidity of metals seriously limit their applicability in portable and wearable electronic equipment. A common method for reducing the density of metal-based materials is to prepare metal nanowire aerogels by freeze-drying, but the weak connection among the nanowires results in poor mechanical and electrical properties. Herein, a facile approach is developed for the one-step synthesis of silver nanowire (AgNW) aerogels with ultralow density, good flexibility, high electrical conductivity, and a robust structure. The gel is directly formed by in situ assembly of AgNWs. The end-to-end nanojoining of AgNWs contributes to constructing an interconnected three-dimensional (3D) network, resulting in improved mechanical and electrical properties. The AgNW aerogel with an ultralow density of 4.87 mg cm-3 demonstrates a high electrical conductivity of 4584 S m-1. Moreover, the porous structure of the AgNW aerogel provides numerous interfaces for multiple reflections and scattering of EM waves, allowing them to be continuously absorbed and dissipated within the aerogel. Thus, the AgNW aerogel exhibits a superb EMI shielding effectiveness (SE) of 109.3 dB and a normalized surface specific SE (SSE/t, calculated as the SE divided by the density and thickness) of 353 183 dB cm2 g-1, significantly above that of previously known shielding materials. This work provides a new route for preparing high-performance metal nanowire aerogels and their great potential in EMI shielding.

Aptamer-coated track-etched membranes with a nanostructured silver layer for single virus detection in biological fluids.

Aptasensors based on surface-enhanced Raman spectroscopy (SERS) are of high interest due to the superior specificity and low limit of detection. It is possible to produce stable and cheap SERS-active substrates and portable equipment meeting the requirements of point-of-care devices. Here we combine the membrane filtration and SERS-active substrate in the one pot. This approach allows efficient adsorption of the viruses from the solution onto aptamer-covered silver nanoparticles. Specific determination of the viruses was provided by the aptamer to influenza A virus labeled with the Raman-active label. The SERS-signal from the label was decreased with a descending concentration of the target virus. Even several virus particles in the sample provided an increase in SERS-spectra intensity, requiring only a few minutes for the interaction between the aptamer and the virus. The limit of detection of the aptasensor was as low as 10 viral particles per mL (VP/mL) of influenza A virus or 2 VP/mL per probe. This value overcomes the limit of detection of PCR techniques (∼103 VP/mL). The proposed biosensor is very convenient for point-of-care applications.

Tunable Head-Conducting Microwave-Absorbing Multifunctional Composites with Excellent Microwave Absorption, Thermal Conductivity and Mechanical Properties

Developing composite materials with both thermal conductivity and microwave absorption is an effective strategy to solve the problems of heat dissipation burden and microwave radiation interference caused by the development of miniaturization and high performance of portable electronic equipment. However, these properties are not easy to simultaneously implement due to the limitation of single type fillers with a single particle size, inspiring the possibility of realizing multifunctional composites with the introduction of composite fillers. In this work, using alumina (Al2O3) and zinc oxide (ZnO) as head-conducting fillers, carbonyl iron (Fe(CO)5) as microwave-absorbing fillers, silicone rubber (SR) composites (Al2O3/ZnO/Fe(CO)5/SR) with enhanced microwave absorption, high thermal conductivity and good mechanical properties were successfully mass prepared. It was found that the composites can achieve a thermal conductivity of 3.61 W·m−1·K−1, an effective microwave absorption bandwidth of 10.86–15.47 GHz. Especially, there is an effective microwave absorption efficiency of 99% at 12.46–14.27 GHz, which can realize the integration of electromagnetic shielding and heat dissipation. The compact microstructure, formed by the overlapping of large particle size fillers and the filling of their gaps by small particle size fillers, is helpful to enhance the thermal conduction path and weaken the microwave reflection. The heat-conducting microwave-absorbing Al2O3/ZnO/Fe(CO)5/SR composites also have the advantages of thermal stability, lightness and flexibility, providing a certain experimental basis for the research and development of high-performance and diversified composites.

Assessment of microbial bioburden on portable medical equipment in a hospital setting.

Although routine disinfection of portable medical equipment is required in most hospitals, frontline staff may not be able to disinfect portable medical equipment at a rate that adequately maintains low bioburden on high-use equipment. This study quantified bioburden over an extended time period for two types of portable medical equipment, workstations on wheels and vitals machines, across three hospital wards. Bioburden was quantified via press plate samples taken from high touch surfaces on 10 workstations on wheels and 5 vitals machines on each of 3 medical surgical units. The samples were taken at three timepoints each day over a 4-week period, with random rotation of timepoints and portable medical equipment, such that frontline staff were not aware at which timepoint their portable medical equipment would be sampled. The mean bioburden from the different locations and portable medical equipment was estimated and compared with Bayesian multilevel negative binomial regression models. Model estimated mean colony counts (95% credible interval) were 14.4 (7.7-26.7) for vitals machines and 29.2 (16.1-51.1) for workstations on wheels. For the workstations on wheel, colony counts were lower on the mouse, 0.22 (0.16-0.29), tray, 0.29 (0.22, 0.38), and keyboard, 0.43 (0.32-0.55), when compared to the arm, as assessed by incident rate ratios. Although routine disinfection is required, bioburden is still present across portable medical equipment on a variety of surfaces. The difference in bioburden levels among surfaces likely reflects differences in touch patterns for the different portable medical equipment and surfaces on the portable medical equipment. Although the association of portable medical equipment bioburden to healthcare-associated infection transmission was not assessed, this study provides evidence for the potential of portable medical equipment as a vector for healthcare-associated infection transmission despite hospital disinfection requirements.

Validation of portable electronic equipment (Accutrend® Plus) to determine glucose, total cholesterol, and triglycerides in rats (Rattus) and dogs (Canis lupus familiaris).

This study aimed to validate the analytical precision of the Accutrend® Plus portable electronic equipment (PE) to determine glucose (GLU), total cholesterol (TC), and triglycerides (TG) in rats and dogs using the conventional laboratory method (CM) as a reference. To determine the analytical accuracy of the Accutrend® Plus in the measurement of GLU, CT, and TG. The EP-9-A2 guide (Clinical and Laboratory Standards Institute), Bland-Altman graphical analysis, and Lin's correlation coefficient of concordance (CCC) were implemented. The average differences (p > 0.05) between PE and CM for GLU, TC, and TG were 2.21, 1.20, and 0.72 mg·dl-1, respectively, in rats and 1.06, 4.30, and 2.41 mg·dl-1, respectively, in dogs (p > 0.05). Both methods showed a linear relationship with Pearson's correlation coefficients > 0.96 and R 2 > 0.97 for the three biochemical indicators evaluated in both species. The GLU, TC, and TG values obtained by the PE were substantial, as evident from Lin's CCC > 0.96. The PE Accutrend® Plus is potent for monitoring GLU, TC, and TG in rats and dogs because of its precision and ability to facilitate measurement by reducing stress in animals during sampling.

Application of promising radio communications in the departments of the internal affairs

The article deals with topical issues related to the problem of the outdated fleet of portable radio equipment, which are in service with the units of the internal affairs bodies, as well as the variety of technologies on the basis of which portable radio equipment is built. At present, both analog and digital portable radio stations of FM, DMR, TETRA and APCO P25 standards are simultaneously used in the internal affairs bodies. The portable radio communications used are not always able to meet the requirements for the timeliness and security of transmitted and received operationally significant information in the course of operational search activities. Failure to comply with the above requirements will inevitably lead to the impossibility of managing units, and as a result, to the disruption of operational-search activities.

Development of a Checklist to Identify Injury Hazards on Row Crop Farms in the Midwestern United States.

Agriculture is among the most dangerous industries in the U.S., yet routine surveillance of injury hazards is not currently being conducted on a national level. The objectives of this study were to describe a new tool, called the Hazard Assessment Checklist (HAC), to identify and characterize farm hazards that increase injury risk to farmers and farm workers, and (2) report the inter-rater reliability of the new tool when administered on row-crop farms in Iowa. Based on a literature review and a consensus of expert opinion, the HAC included hazards related to self-propelled vehicles, powered portable implements, fixed machinery and equipment, farm buildings and structures, fall risks, and portable equipment associated with fall risk. A scoring metric indicating the extent of compliance with recommended safety guidelines and standards was developed for each item of the HAC, which included compliant, minimal improvement needed, substantial improvement needed, and not compliant. Inter-rater reliability was assessed from data collected by research staff on 52 row crop farms in Iowa. Cohen's weighted Kappa values demonstrated high inter-rater reliability, ranging between 0.86 and 0.94, for all HAC sections. The HAC can be completed in 1.5-2 hours on each farm and requires about three hours of training, two hours of which are spent in field training. The ability to monitor injury-related hazards over time using an empirically driven tool will contribute significantly to injury prevention efforts in an industry with consistently high rates of fatal and nonfatal injury.

Label-free DNA quantification using isothermal amplification on an exposed core optical fiber microfluidic platform.

Isothermal amplification technology has triggered a surge in research due to its compatibility with small and portable equipment, simplicity, and high efficiency, especially in light of the COVID-19 pandemic where reliable widescale testing is critical to outbreak management. In this paper, a label-free isothermal deoxyribonucleic acid (DNA) amplification method based on refractive index (RI) quantification is proposed and demonstrated for the first time by combining optical fiber sensing, microfluidics, and isothermal amplification. A highly RI-sensitive Mach-Zehnder (MZ) interference is formed by splicing a short length of an exposed-core fiber between two lengths of a single-mode fiber while the microfluidic liquid channel on the exposed side of the ECF is filled with target DNA and the amplification solution. Real-time quantitative measurement of the target DNA is then realized by monitoring the change in RI of the solution during the isothermal DNA amplification process. The experimental results show that the platform successfully realizes real-time label-free monitoring of isothermal amplification of 0.16 aM DNA samples. This method is a breakthrough for applications in the fields of DNA detection and quantification where simple operation, rapid detection, portability, small size, high selectivity, and high sensitivity are required.

Manually operated portable equipment for measurement and classification of fresh pork belly firmness

The single most important characteristic of a pork belly, which is the most valuable pork carcass primal in North America, is its degree of firmness. To date, firmness evaluation has either been subjective and therefore variable, or require 1–5 min for an objective assessment in the latter stages of fresh production. The invention is a machine for rapid and standardized measurement of fresh pork belly firmness as soon as the belly is removed from either the left or right side of the carcass. The equipment is manually operated, compact, portable, and has the flexibility to be adapted to long or short bellies across a wide range of carcass weights. Although designed to be used with rib-in bellies, it can also be used with ribbed bellies. Firmness categorization rather than measurement can be achieved by careful placement of bracing in the angle gauge. As it is constructed from approved food safe materials, the invention can be used in meat production areas and fully washed down with other equipment at the end of the production day. The invention is designed for data collection in either scientific or industry meat research. Benefiters include meat scientists, pork packers, and swine breeding companies.