Polyethylene Composites Research Articles

Evaluation and characterization of polyethylene composites with β-cyclodextrin andβ-cyclodextrin-based derivatives as foaming nucleating agent

In this study, we prepared nanosponges (NS) by crosslinking the hydroxyl group of β-cyclodextrin (CD) molecular. Furthermore, we modified the CD molecular by 1, 2-cyclohexanediamine (TRK) through simple chemical method. CD, NS and CD-TRK were used as nucleating agent in the injection foaming process of polyethylene (PE) with 4, 4'-oxydibenzenesulfonyl hydrazide as blowing agent. With addition of CD-TRK, the crystallinity increased from 39.17% for pure PE to 46.02% for PE/CD-TRK-1.0 composites. Results showed that PE/CD-TRK-1.0 composites presented the best foam morphology. The cell density increased by about 10 times, while the cell diameter reduced by about 56% compared with that of pure PE. Scanning electron microscopy analysis showed that CD-TRK exhibited more compact and dense network structure with uniform cavity distribution, which may reduce the cell nucleation barrier and provide proper nucleation site for cells. The dynamic mechanical analysis showed that PE/CD-TRK-1.0 composites displayed proper modulus and viscoelasticity, which were favor for cell nucleation, growth and stabilization, resulting in the best cell morphology of PE/CD-TRK composites. Tensile and impact strength of foaming PE composites were systematically analyzed. The maximum impact strength reached 27.4 KJ·m−2, and the maximum tensile strength reached 27.5 MPa.

Exploring the Effects of Nano-CaCO3 on the Core-Shell Structure and Properties of HDPE/POE/Nano-CaCO3 Ternary Nanocomposites.

To address the dilemma of the stiffness and toughness properties of high-density polyethylene (HDPE) composites, titanate coupling agent-treated CaCO3 nanoparticles (nano-CaCO3) and ethylene-octene copolymer (POE) were utilized to blend with HDPE to prepare ternary nanocomposites via a two-sequence-step process. Meanwhile, a one-step process was also studied as a control. The obtained ternary nanocomposites were characterized by scanning electron microscopy (SEM), Advanced Rheometrics Expansion System (ARES), Dynamic Mechanical Analysis (DMA), wide-angle X-ray diffraction analysis (WXRD), and mechanical test. The SEM results showed one or two CaCO3 nanoparticles were well-encapsulated by POE and were uniformly dispersed into the HDPE matrix to form a core-shell structure of 100-200 nm in size by the two-step process, while CaCO3 nanoparticles were aggregated in the HDPE matrix by the one-step method. The result of the XRD showed that the nano-CaCO3 particle played a role in promoting crystallization in HDPE nanocomposites. Mechanical tests showed that the synergistic effect of both the POE elastomer and CaCO3 nanoparticles should account for the balanced performance of the ternary composites. In comparison with neat HDPE, the notched impact toughness of the ternary nanocomposites of HDPE/POE/nano-CaCO3 was significantly increased. In addition, the core-shell structure absorbed the fracture impact energy and prevent further propagation of micro-cracks, thus obtaining a higher notched Izod impact strength.

Highly Efficient and Eco-Friendly Thermal-Neutron-Shielding Materials Based on Recycled High-Density Polyethylene and Gadolinium Oxide Composites.

Due to the increasing demands for improved radiation safety and the growing concerns regarding the excessive use of plastics, this work aimed to develop effective and eco-friendly thermal-neutron-shielding materials based on recycled high-density polyethylene (r-HDPE) composites containing varying surface-treated gadolinium oxide (Gd2O3) contents (0, 5, 10, 15, and 20 wt%). The results indicate that the overall thermal-neutron-shielding properties of the r-HDPE composites were enhanced with the addition of Gd2O3, as evidenced by large reductions in I/I0, HVL, and TVL, as well as the substantial increases in ∑t and ∑t/ρ of the composites. Furthermore, the results reveal that the values for tensile properties initially increased up to 5-15 wt% of Gd2O3 and then gradually decreased at higher contents. In addition, the results show that the addition of Gd2O3 particles generally increased the density (ρ), the remaining ash at 600 °C, and the degree of crystallinity (%XC) of the composites. This work also determined the effects of gamma irradiation on relevant properties of the composites. The findings indicate that following gamma aging, the tensile modulus slightly increased, while the tensile strength, elongation at break, and hardness (Shore D) showed no significant (p < 0.05) differences, except for the sample containing 5 wt% of Gd2O3, which exhibited a noticeable reduction in elongation at break. Furthermore, by comparing the neutron-shielding and mechanical properties of the developed r-HDPE composites with common borated polyethylene (PE) containing 5 wt% and 15 wt% of boron, the results clearly indicate the superior shielding and tensile properties in the r-HDPE composites, implying the great potential of r-HDPE composites to replace virgin plastics as effective and more eco-friendly shielding materials.

High Speed Impact Testing of UHMWPE Composite Using Orthogonal Arrays

BackgroundUltra high molecular weight polyethylene composites are fiber based composites used in armor applications. While some characterization has been conducted experimentally, this study varies multiple parameters simultaneously to investigate material response under a wide range of conditions.ObjectiveThis work focuses on characterizing the response of Dyneema® HB26 hard laminate composites under high-speed impacts to examine the influence of plate diameter, clamping pressure, and plate spacing on target performance. Additionally, micro Computer Tomography scans are used to nondestructively evaluate the damage evolution in the targets.MethodsThese scan results are used in concert with more traditional armor performance metrics to evaluate the effect of various parameters using the method of orthogonal array analysis. This technique allows for multiple variables to be investigated in the same test series, saving time and budget while still providing quality results across a range of variables and variable values.ResultsWe conclude that of the parameters investigated, the plate spacing parameter has the largest effect on performance, followed by the plate diameter. Bolt torque was found to not have a significant impact on results, indicating that an edge clamping pressure is not critical to material response. Additionally, by examining the high resolution scans, we can quantify the damage with an effective damage angle and that this angle is a good predictor of performance. ConclusionFinally a damage theory involving the effective bending strength of the plates is discussed as an explanation for all of the results observed in this test series.

Synthesis and Behavior Study of Basalt Fiber-Made Low-Density Polyethylene Composites Via Injection Mold

Synthesis and Behavior Study of Basalt Fiber-Made Low-Density Polyethylene Composites Via Injection Mold

Analysis of the Effects of Fiber Loading on the Mechanical Behavior of Jute Reinforced Thermoplastic Composites

Natural fiber-reinforced composites are becoming a growing trend because of their affordability, sustainability, abundant natural source, and minimal environmental effect. It has also shown to be an effective replacement of synthetic fiber, particularly in the transportation and construction sectors as ceiling, paneling, partition etc. In this study the jute fiber (Hessian Cloth) reinforced (10% to 50% fiber content by weight) Polypropylene (PP) and Polyethylene (PE) composite were made by compression molding technique to understand the effect of fiber loading on mechanical properties of two different thermoplastic composite materials. For jute fabric-reinforced thermoplastic composites, it was discovered that with 30 % fiber loading with PP and PE yielded the best results. It was found that the mechanical properties of the composites enhanced significantly with 30 % fiber content with PP and PE thermoplastic matrixes in contrast to 10% and 20% fiber content composites. However, increasing the fiber content over 30%, dramatically decrease the mechanical properties of the composite samples. The relationship between Tensile Strength (TS), Bending Strength (BS), Impact Strength (IS) and Tensile Modulus (TM), Bending Modulus (BM) was examined, along with water resistance properties for both composites. Additionally, the jute-reinforced polypropylene (PP) composite showed superior mechanical capabilities compared to the jute-polyethylene (PE) composite. This suggests that it could be a suitable replacement for the toy manufacturing, home or garden furniture, automotive and interior construction industries in the future.

Effect of Nitrate Acid Treated Dolomite on the Tensile Properties of Ultra-High Molecular Weight Polyethylene (UHMWPE) Composites

Ultra-High Molecular Weight Polyethylene (UHMWPE) polymers have been used in biomedical applications due to its biocompatibility, durability, toughness and high wear resistance. To enhance the mechanical properties, various types of minerals are commonly utilized as fillers in UHMWPE. One of the minerals is dolomite, which has been recognized as a valuable mineral with versatile applications, particularly in the field of biomedical applications. This paper presents the tensile properties of UHMWPE composites that filled with dolomite and treated-dolomite at various filler loading (i.e., 1-5 wt.%). Nitric acid and diammonium phosphate were used to treat the dolomite. From the results, the peaks of the FTIR spectrum displays carbonate (CO3–2), phosphate (PO4–3) and hydroxyl (OH–) groups in the ct-dolomite powder sample while the XRD pattern reveals that using dolomite treated with 1M nitric acid resulted in the presence of calcium hydroxide phosphate (Ca10(PO4)5(OH)) and MgO. For tensile strength, UHMWPE/ct-dolomite composites show better tensile strength than the pure UHMWPE composites. Treated improve the dolomite filler and resulted in significantly better matrix-filler interfacial interactions and improve the properties.

Assessing the recycling potential of thermosetting polymer waste in high-density polyethylene composites for safety helmet applications

Abstract The rising demand for thermosetting polymers has resulted in the production of large amounts of industrial waste. Environmental issues due to waste landfills and increased raw material costs for new product development have led to the development of innovative recycling methods. This study focuses on the development of a product (helmet shell) by reinforcing thermosetting polymer waste (TPW) as a filler in a high-density polyethylene (HDPE) matrix. The HDPE and TPW were converted into extrudates using a twin-screw extruder. Then, the extrudate was pelletized to use as raw material for the injection molding machine. The HDPE/TPW composites were fabricated using injection molding. Maleic anhydride-grafted polyethylene was employed as a compatibilizer. In the composite, the TPW volume was reinforced at various weight percentages, ranging from 0 to 35 wt%. The mechanical, thermal, and viscoelastic properties of the composites can be enhanced by uniformly dispersing TPW in the HDPE matrix. However, it is difficult to achieve uniform dispersion at higher TPW volumes owing to the agglomeration effect. According to these findings, the mechanical properties were enhanced by up to 30 wt% addition of TPW. The findings suggest that the proposed composite has sufficient mechanical properties to be suitable for the fabrication of helmet shells.

Improvement of mechanical properties of highly ZnO‐filled polyethylene composites by dual‐compatibilizer for hydrogen sulfide permeation inhibition

AbstractTransportation of acidic fluids containing hydrogen sulfide (H2S) by flexible reinforced thermoplastic pipes can cause safety problems due to diffusion of H2S in the pipe. Herein, high‐density polyethylene (HDPE) composites are prepared with a large amount of zinc oxide (ZnO) particles as absorbent fillers by melt‐mixing via introducing maleic anhydride‐grafted polyethylene (PE‐g‐MAH) and maleic anhydride‐grafted poly(ethylene‐co‐octene) (POE‐g‐MAH) as dual‐compatibilizer. By controlling the mass ratio of the two compatibilizers, ZnO particles can be encapsulated by PE‐g‐MAH and POE‐g‐MAH so that mechanical properties of the prepared HDPE/ZnO composites are improved owing to enhanced compatibility between the filler and the resin. By adding PE‐g‐MAH and POE‐g‐MAH with total 10 wt% in a mass ratio of 1/3, the HDPE/ZnO composite containing 50 wt% ZnO exhibits 37.3 ± 3.8 MPa of yield strength, 576 ± 16 MPa of flexural modulus, and 84.4 ± 1.4 kJ m−2 of notched Izod impact strength corrected to 311 ± 24.9 kJ m−2. After exposure in H2S at 0.1 MPa for 7 days, the diffusion distance of H2S in the composite is 659 ± 17 μm, demonstrating a high barrier ability on H2S via absorption. This study provides a feasible method for preparation of polymer composites with suitable mechanical properties for inhibiting H2S permeation in reinforced thermoplastic pipes.

Enhancing Wear Resistance of UHMWPE Composites with Micro MoS2 and Nano Graphite: A Taguchi-DOE Approach.

This study presents an in-depth investigation into the wear characteristics of ultrahigh-molecular-weight polyethylene (UHMWPE) composites reinforced with microsized MoS2 and nanosized graphite particles. The objective is to enhance the wear resistance of the UHMWPE by examining the effects of various parameters and optimizing the wear performance. To achieve this goal, wet wear tests were conducted under controlled conditions, and the results were compared between composites with micro MoS2 and nano graphite reinforcements. The Taguchi method was employed to design the experiments (DOE) using an L9 orthogonal array. Four key parameters, namely, reinforcement percentage, load, speed, and track radius, were varied systematically to analyze their impact on wear characteristics, including wear rate, frictional forces, and the coefficient of friction (COF). The data obtained from the experiments were subjected to analysis of variance (ANOVA) to identify the significant factors affecting wear behavior. Subsequently, the optimal wear parameters were determined through regression analysis, allowing for the prediction of wear characteristics under the optimum conditions. This research not only provides insights into the comparative performance of micro MoS2 and nano graphite reinforcements in UHMWPE composites but also offers a comprehensive approach to optimizing wear resistance by employing advanced statistical and experimental techniques. The findings contribute to the development of more durable and wear-resistant materials with potential applications in various industries, such as those investigated in the study, which are commonly employed, such as automotive, aerospace, medical devices, or manufacturing.

Investigation and Improvement of Thermal and Mechanical Properties of Recycled Polypropylene / Oxidized Polyethylene Composites

In this study, various composites were prepared from synthetic wastes with oxidized polyolefin (OxPO) and the mechanical (elongation, elasticity, tensile strength, etc.) of these composites.) and discusses the results of an experimental study on its thermal characterization. The oxidized polyolefin/Styrene (St) mixture was infused with the melt free radical polymerization method on recycled polypropylene (rPP). The effect of the initial monomer concentration on the mechanical properties of recycled polypropylene was investigated. The mechanical (elongation and tensile strength) properties of the composites produced were made according to the ISO 527-2 standard method. It has been observed that the tensile strength and elongation, which are the mechanical properties of (OxPO/St)/rPP composites, increase compared to RPP. The resulting polymers were then characterized by Fourier transformational infrared spectroscopy (FTIR).

Preparation and properties of multilayer core-shell structure ammonium polyphosphate synergistic with THEIC for flame retardant LDPE

In this paper, a new type of highly efficient intumescent flame-retardant low-density polyethylene composite was prepared using two key technologies, namely, microencapsulation encapsulation technology and novel carbon formation technology. Precisely, β-cyclodextrin encapsulated modified ammonium polyphosphate@melamine formaldehyde resin (β-CDMCAPP@MF) was prepared by using Si-IFR synergistic flame retardant effect combined with the gel-solution method, and then flame retardant low-density polyethylene (LDPE) was prepared by compounding with tris-(2-hydroxyethyl) isocyanate (THEIC). The results showed that β-CDMCAPP@MF was modified with MF, β-CD, and silica coating. This modification resulted in excellent hydrophobicity and good compatibility with LDPE. The addition of IFR containing β-CDMCAPP@MF significantly improved the flame retardancy of the LDPE composites. Specifically, when 30 wt% of β-CDMCAPP@MF was added, the ultimate oxygen index of the composites reached 24.7 %, and V-0 grade and the tensile strength went 11.41 MPa. Compared with IFR/LDPE with the same proportion of MF@MCAPP and β-CD@MCAPP, the ultimate oxygen indices were increased by 9.72 % and 12.15 %, respectively. The introduction of THEIC into the flame retardant system resulted in a LOI value of 36.5 % and an FRI value of 2.523, which is 32.33 % higher than that of the composites containing 30 wt% of the flame retardant system (without THEIC). Cone calorimetry test results showed that introducing β-CDMCAPP@MF and THEIC significantly improved the smoke emission.

The composites of cross-linked polyethylene with enhanced thermal conductivity

The composites of cross-linked polyethylene with enhanced thermal conductivity

High‐performance wood‐reinforced crosslinked high‐density polyethylene composites

AbstractThis paper presents a comprehensive investigation into the manufacturing of high‐performance wood‐crosslinked high‐density polyethylene composites (WxHDPEC). In particular, the effect of maleated polyethylene (MAPE) treatment and concentration (0–50 wt%) of maple wood fibers is investigated. The samples were produced via dry‐blending followed by compression molding and a set of characterization was performed including chemical, morphological, mechanical, thermal, and physical properties. The gel content was found to increase with increasing wood fiber content, while the surface modification significantly improved the tensile strength (11%), tensile modulus (298%), flexural strength (138%), and flexural modulus (81%). Thermal analyses also showed improved thermal stability and higher thermal resistance for the treated composites. Finally, the Shore D hardness increased by 11.0 (from 61.5 to 72.5) and 12.1 (from 61.5 to 73.6) points, while the Shore A hardness increased by 7.5 (from 91.5 to 99.0) and 8.1 (from 91.5 to 99.6) points for the untreated and treated composites, respectively. These improvements are attributed to effective adhesion between MAPE‐treated wood fibers and the xHDPE matrix. The findings not only advance our understanding of these complex materials but also provide alternatives for various applications from construction to automotive engineering.Highlights High‐performance wood‐reinforced crosslinked high‐density polyethylene was produced. The effect of maleated polyethylene (MAPE) treatment and maple wood fibers was studied. Higher crosslink density in MAPE‐treated wood‐xHDPE was obtained. Wood‐crosslinked high‐density polyethylene composites have better properties.

Effects of chemical treatment and gamma-ray irradiation on the structure-properties of sunn hemp and okra hessian cloth reinforced high-density polyethylene composites: A comparative study

Okra hessian cloth and Sunn hemp hessian cloth were prepared and treated with 5, 10, and 15 wt% alkali solutions for 1 h. The optimized concentration of alkali is 10 wt%. The untreated and treated hessian cloths reinforced high-density polyethylene (HDPE) composites were then prepared using the compression molding method. Alkali-treated, and 55 wt% fiber contents reinforced composites showed improved mechanical properties among 40, 45, 50, 55, 60, and 65 wt% fiber contents composites. 55 wt% fiber contents reinforced composites were then irradiated under gamma-ray at doses 2.5–7.5 kGy at the rate of 6 kGy/h. According to the X-ray diffraction analysis results, only alkali-treated Okra reinforced, and Sunn hemp-reinforced HDPE composites had higher crystallinity values than untreated and irradiated composites. Surface micrographs showed that the Okra-HDPE and Sunn hemp-HDPE had better matrix and fiber attachment. Cross-linking between the two varieties of fibers and matrix was seen using Fourier-transform infrared (FTIR) spectroscopy. Both irradiated composites exhibited greater hydrophobicity in their water intake characteristics compared to untreated and alkali-treated composites. The tensile strength ( TS) value of Sunn hemp composite for 5 kGy gamma-ray irradiation dose is 68 MPa, which is 14% and 42% higher than that of treated and untreated composites, respectively. For comparison, the TS value for 5 kGy dose irradiated Okra composite is 66 MPa, which is 17% and 44% higher than that of treated and untreated composites, respectively. Young’s modulus ( Y) values of irradiated Okra composite and irradiated Sunn hemp composite showed higher values than that of other composites. Both irradiated composites have better thermal and structural characteristics than untreated and alkali-treated composites.

Enhancing interface compatibility in high-filled coal gangue/polyethylene composites through silane coupling agent-mediated interface modification

This study investigates the profound impact of surface modification using the silane coupling agent KH550 on Coal Gangue (CG)-Polyethylene (PE) composites. The aim was to enhance the properties of composites while addressing waste material accumulation concerns. Comprehensive analyses elucidated the mechanism of interface formation and the subsequent influence on composite properties. Surface modification of CG with KH550 demonstrated pronounced effects on physical, mechanical, and thermal properties of the resulting composites. Notably, the coupling agent facilitated covalent bonding with CG, preventing particle agglomeration and enhancing dispersion stability. The introduction of KH550 contributed to heterogeneous nucleation, augmenting composite crystallinity and interfacial bonding with the resin, thereby improving overall compatibility. Mechanical tests revealed substantial enhancements in tensile and bending strengths with optimal KH550 content. However, excess KH550 led to diminishing returns, highlighting the critical balance required for effective modification. Thermal stability assessments demonstrated improved properties owing to KH550 modification, validating its role in safeguarding the composite matrix from thermal degradation. Microstructural analyses, including SEM, FTIR, DSC, and XRD, provided insights into the interface morphology, chemical composition, crystalline behavior, and structure of the composites. The SEM micrographs elucidated a progressive shift from clear interface boundaries to more homogenously blended states with increasing KH550 content, indicative of enhanced interaction between CG and PE. This comprehensive study demonstrates that KH550 modification offers a strategic approach to optimize CG-PE composites, showcasing potential applications in the automotive and construction industries. Those findings underscore the significance of surface modification techniques in enhancing composite properties and utilizing waste resources efficiently.

Avocado Pruning Residues for the Formulation of Bio‐Based Polyethylene/Fiber‐Based Biocomposites for Sustainable Food Packaging

AbstractThe extensive use of non‐biodegradable bioplastics and fossil‐based plastics in food packaging presents a significant environmental challenge. Consequently, there has been a growing interest in exploring agricultural biomass as a potential source for formulating biocomposites for packaging due to the substantial amount of lignocellulosic residue generated. This study explores the utilization of avocado pruning residue (APR) for isolating lignocellulose fibers and their application as replacement and reinforcement material for bio‐based polyethylene (BioPE) composites. The results obtained reveal that a concentration of 9% (w/w) of maleic anhydride‐grafted‐polyethylene (MAPE) shows the most effective fiber–polymer interaction, resulting in a significant improvement of 25.47% in the mechanical properties. Biocomposites with varying fiber concentrations, ranging from 10% to 40% (w/w), are prepared and assessed for their macro‐ and micromechanical properties. The results demonstrate a substantial 49% increase in tensile strength and a remarkable 325% enhancement in Young's modulus for biocomposites containing 40% (w/w) fiber content. Furthermore, micromechanical analysis provides insights into the intrinsic strength and modulus of avocado fibers, with values of ≈437 MPa and 33 GPa, respectively. This research contributes to the development of sustainable and eco‐friendly alternatives for food packaging, reducing the reliance on fossil‐based plastics, and promoting the utilization of agricultural waste.

Quasi‐static and high‐rate in‐plane shear tests on aramid and carbon fiber woven composites featuring a nanoparticle‐enriched high‐density polyethylene matrix

AbstractNanoparticles are known to enable the modification of the properties of the material they are integrated into. In the context of ballistic protection, previous works have demonstrated that graphene and Montmorillonite (MMT) particles included in high‐density polyethylene (HD‐PE) and used as a matrix enable an increase in the ballistic performance, of consolidated woven aramid fabrics. Furthermore, the ballistic performance has been reported to be influenced by the in‐plane shear properties of the impacted materials. In this context, quasi‐static and high‐rate in‐plane shear tests have been conducted on two types of reinforcements, aramid, and carbon woven fabrics, consolidated by a high‐density polyethylene matrix enriched by graphene, MMT and a mix of graphene and MMT nanoparticles. The conducted investigations provide for the first time in the literature the results of high‐rate in‐plane shear tests on aramid woven reinforcement consolidated with nanoparticle‐enriched and not enriched high‐density polyethylene composites. Despite the use of the same reinforcement and enriched matrix material as in previous works of literature, no significant differences in terms of in‐plane shear behavior have been observed for any of the different types of nanoparticles integrated into the matrix. Nevertheless, the obtained results demonstrate a clear strain rate sensitivity of the tested materials.Highlights Aramid and carbon fabrics were consolidated with nanoparticle‐enriched HD‐PE Quasi‐static and high‐rate in‐plane shear tests were conducted No influence of the nanoparticles could be identified A clear strain‐rate sensitivity could be identified for both composites

Tensile properties of banana fiber reinforced recycled high‐density polyethylene composites: An experimental investigation

AbstractNatural fiber‐reinforced polymer composites (NFRCs) are increasingly favored over synthetic fiber‐reinforced alternatives due to their beneficial properties and environmental sustainability. Mechanical properties of composites are critical to ensure optimized utilization of NFRCs. Here, this research explores the effects of different fiber parameters on the tensile strength of high‐density polymer composites reinforced with banana fiber and utilizes the Taguchi method for both experimental and statistical analysis of the outcomes. Three different parameters are considered here: weight fractions, fiber orientation angle, and plasma treatment to fabricate the composites using the compression molding process. Taguchi analysis revealed that fiber orientation angle has the greatest influence among the three variables, with plasma treatment and weight fraction following in impact on tensile strength. The composite that exhibited the highest tensile strength was determined to have a weight fraction of 10%, a fiber orientation angle of 90°, and a plasma treatment period of 5 min. This combination yielded a strength of 30.351 MPa. The analysis of the interaction between any two factors was done using contour plots. In order to compare the experimental tensile strength values with the anticipated values derived from the regression equation, regression analysis was carried out.Highlights Composites were made up of recycled HDPE (rHDPE) from plastic bottles using a compression molding technique. The Taguchi method is applied to achieve an experimental design employing an L4 orthogonal array. Contour plot analysis is conducted to identify points of minimum and maximum responses, as anticipated from the results. Tensile strength was optimized to a maximum of 30.351 MPa.

The impact of chemical treatment and gamma-ray irradiation on the okra hessian cloth reinforced high-density polyethylene composites

Okra hessian cloth-reinforced high-density polyethylene (HDPE) thermoplastic composites were prepared and characterized with both raw and alkali-treated fibers. The fiber contents were optimized for both the raw Okra thermoplastic composites and the alkali-treated Okra thermoplastic composites, and the optimum value of fiber content was 55 wt%. Samples that were alkali-treated and had 55 wt% fibers were subsequently exposed to gamma radiation at doses of 2.5, 5, and 7.5 kGy. Only the sample subjected to 5 kGy showed improved performance. Treated composites exhibited higher crystallinities than the untreated samples as observed by X-Ray diffraction analysis. The rupture surface micrographs of the composites exposed to 5 kGy gamma radiation revealed more compact than others. By using Fourier transform infrared spectroscopy analysis of composites, it was found that 5 kGy dose sample showed enhanced cross-linking between Okra fibers and HDPE matrix. The irradiated composite showed less water intake than the alkali-treated samples. Composites subjected to 5 kGy gamma rays showed improved tensile strength and Young’s modulus of values 66 MPa and 1925 MPa, respectively. Compared to raw and treated composites, the irradiated composites with a radiation dose of 5 kGy showed improved structural, mechanical, and thermal properties.