Polyelectrolyte Multilayer Systems Research Articles

Effects of Feed Solution pH on Polyelectrolyte Multilayer Nanofiltration Membranes.

Over the past decade polyelectrolyte multilayer (PEM)-based membranes have gained a lot of interest in the field of nanofiltration (NF) as an alternative to conventional polyamide-based thin film composite membranes. With great variety in fabrication conditions, these membranes can achieve superior properties such as high chemical resistance and excellent filtration performance. Some of the most common polyelectrolytes used to prepare NF membranes are weak, meaning that their charge density depends on pH within the normal window of operation relevant for potential applications (pH 0-14). This might cause a dependency of membrane properties on the pH of filtered solutions, as indicated by other applications of PEMs. In this work, the susceptibility of membrane structure (swelling and surface charge) and performance (permeability, molecular weight cutoff, and salt retention) toward the pH of the filtration solution was studied for four fundamentally different PEM systems: poly(diallyldimethylammonium chloride) (PDADMAC)/poly(sodium-4-styrenesulfonate) (PSS) (strong/strong), poly(allylamine hydrochloric acid) (PAH)/poly(acrylic acid) (PAA) (weak/weak), and PAH/PSS (weak/strong) and PAH/PSS+PAH/PAA (asymmetric). Slight variations in structure and performance of the PDADMAC/PSS-based membranes were observed. On the contrary, structure and performance of PAH/PAA-based membranes are very susceptible to feed solution pH. A continuous change in charge density with variation in pH significantly affects salt retention. An increased swelling at pH 9 translates to variation in permeability and molecular weight cutoff of the membrane. The susceptibility of PAH/PSS-based membranes to pH is less pronounced compared to the PAH/PAA-based membranes since only one of the polyelectrolytes involved is weak. No structural changes were observed, indicating additional specific interactions between the polyelectrolytes other than electrostatic forces that stabilize film structure. A combination of the PAH/PSS and PAH/PAA system (8 + 2 bilayers) also displays a clear dependency of both membrane structure and performance on solution pH, where PAH/PSS is dominating due to a higher bilayer number.

Relating uncharged solute retention of polyelectrolyte multilayer nanofiltration membranes to effective structural properties

A novel way of making Nanofiltration (NF) membranes is to apply the Layer-by-Layer method, where polyelectrolytes are alternatingly coated on top of a porous Ultrafiltration membrane to form a separation layer with a controllable thickness in the nanometer range, also known as Polyelectrolyte Multilayer (PEM). An important precondition to make use of the variety this fabrication method offers for membrane optimization is knowledge of design rules. Therefore, the structural properties of PEMs and their relation to both coating conditions and membrane performance is an ongoing field of research. In this work, the separation performance of NF PEM membranes, based on PDADMAC/PSS and PAH/PAA, towards uncharged molecules is related to PEM structure. The structure of the membrane is represented by a nanoporous film with distribution in pore size. As, up to date, no experimental technique is available to directly measure pore sizes in the nanometer range of a wet film, a representative pore size distribution is estimated via the use of a theoretical transport description fitted to experimental data. Here, the studied PEM systems showed distinctive differences in both film thickness (PDADMAC/PSS: 44nm/BL, PAH/PAA: 689nm/BL) and mean pore size (PDADMAC/PSS: 0.44 nm, PAH/PAA: 0.27 nm). Within the range of layer numbers, the pore size of both PEMs in the layer dominated regime was independent of layer number. This indicates that there is an optimum layer number for PEM NF membranes regarding uncharged solute retention. Surprisingly, despite forming much thicker layers the PAH/PAA system closes off the support membrane pores at a higher bilayer number.

Tailored Polyelectrolyte Multilayer Systems by Variation of Polyelectrolyte Composition and EDC/NHS Cross-Linking: Controlled Drug Release vs. Drug Reservoir Capabilities and Cellular Response for Improved Osseointegration.

Polyelectrolyte multilayers (PEM) are versatile tools used to investigate fundamental interactions between material-related parameters and the resulting performance in stem cell differentiation, respectively, in bone tissue engineering. In the present study, we investigate the suitability of PEMs with a varying collagen content for use as drug carriers for the human bone morphogenetic protein 2 (rhBMP-2). We use three different PEM systems consisting either of the positively charged poly-L-lysine or the glycoprotein collagen type I and the negatively charged glycosaminoglycan heparin. For a specific modification of the loading capacity and the release kinetics, the PEMs were stepwise cross-linked before loading with cytokine. We demonstrate the possibility of immobilizing significant amounts of rhBMP-2 in all multilayer systems and to specifically tune its release via cross-linking. Furthermore, we prove that the drug release of rhBMP-2 plays only a minor role in the differentiation of osteoprogenitor cells. We find a significantly higher influence of the immobilized rhBMP-2 within the collagen-rich coatings that obviously represent an excellent mimicry of the native extracellular matrix. The cytokine immobilized in its bioactive form was able to achieve an increase in orders of magnitude both in the early stages of differentiation and in late calcification compared to the unloaded layers.

Tailored Polyelectrolyte Multilayer Systems by Variation of Polyelectrolyte Composition and EDC/NHS Cross-Linking: Physicochemical Characterization and In Vitro Evaluation.

The layer-by-layer (LbL) self-assembly technique is an effective method to immobilize components of the extracellular matrix (ECM) such as collagen and heparin onto, e.g., implant surfaces/medical devices with the aim of forming polyelectrolyte multilayers (PEMs). Increasing evidence even suggests that cross-linking influences the physicochemical character of PEM films since mechanical cues inherent to the substrate may be as important as its chemical nature to influence the cellular behavior. In this study, for the first-time different collagen/heparin films have been prepared and cross-linked with EDC/NHS chemistry. Quartz crystal microbalance, zeta potential analyzer, diffuse reflectance Fourier transform infrared spectroscopy, atomic force microscopy and ellipsometry were used to characterize film growth, stiffness, and topography of different film systems. The analysis of all data proves a nearly linear film growth for all PEM systems, the efficacy of cross-linking and the corresponding changes in the film rigidity after cross-linking and an appropriate surface topography. Furthermore, preliminary cell culture experiments illustrated those cellular processes correlate roughly with the quantity of newly created covalent amide bonds. This allows a precise adjustment of the physicochemical properties of the selected film architecture regarding the desired application and target cells. It could be shown that collagen improves the biocompatibility of heparin containing PEMs and due to their ECM-analogue nature both molecules are ideal candidates intended to be used for any biomedical application with a certain preference to improve the performance of bone implants or bone augmentation strategies.

Extracellular matrix-inspired surface coatings functionalized with dexamethasone-loaded liposomes to induce osteo- and chondrogenic differentiation of multipotent stem cells

Biomimetic surface coatings can be combined with conventional implants to mimic the extracellular matrix (ECM) of the surrounding tissue to make them more biocompatible. Layer-by-layer technique (LbL) can be used for making surface coatings by alternating adsorption of polyanions and polycations from aqueous solutions without need of chemical reactions. Here, polyelectrolyte multilayer (PEM) systems is made of hyaluronic acid (HA) as polyanion and Collagen I (Col) as polycation to mimic the ECM of connective tissue. The PEM are combined with dexamethasone (Dex)-loaded liposomes to achieve a local delivery and protection of this drug for stimulation of osteo- and chondrogenic differentiation of multipotent stem cells. The liposomes possess a positive surface charge that is required for immobilization on the PEM. The surface properties of PEM system show a positive zeta potential after liposome adsorption and a decrease in wettability, both promoting cell adhesion and spreading of C3H10T1/2 multipotent embryonic mouse fibroblasts. Differentiation of C3H10T1/2 was more prominent on the PEM system with embedded Dex-loaded liposomes compared to the basal PEM system and the use of free Dex-loaded liposomes in the supernatant. This was evident by immunohistochemical staining and an upregulation of the expression of genes, which play a key role in osteogenesis (RunX2, ALP, Osteocalcin (OCN)) and chondrogenesis (Sox9, aggrecan (ACAN), collagen type II), determined by quantitative Real-time polymerase chain reaction (qRT-PCR) after 21 days. These findings indicate that the designed liposome-loaded PEM system have high potential for use as drug delivery systems for implant coatings that can induce bone and cartilage differentiation needed for example in osteochondral implants.

In Vitro Microbiological and Drug Release of Silver/Ibuprofen Loaded Wound Dressing Designed for the Treatment of Chronically Infected Painful Wounds.

This study consisted of developing a dressing loaded with silver (Ag) and ibuprofen (IBU) that provides a dual therapy, antibacterial and antalgic, intended for infected painful wounds. Therefore, non-woven polyethyleneterephtalate (PET) textiles nonwovens were pre-treated by cyclodextrin crosslinked with citric acid by a pad/dry/cure process. Then, textiles were impregnated in silver solution followed by a thermal treatment and were then coated by Layer-by-Layer (L-b-L) deposition of a polyelectrolyte multilayer (PEM) system consisting of anionic water-soluble poly(betacyclodextrin citrate) (PCD) and cationic chitosan. Finally, ibuprofen lysinate (IBU-L) was loaded on the PEM coating. We demonstrated the complexation of IBU with native βCD and PCD by phase solubility diagram and 1H NMR. PEM system allowed complete IBU-L release in 6 h in PBS pH 7.4 batch (USP IV). On the other hand, microbiological tests demonstrated that loaded silver induced bacterial reduction of 4 Log10 against S. aureus and E. coli and tests revealed that ibuprofen lysinate loading did not interfere with the antibacterial properties of the dressing.

Engineering osteogenic microenvironments by combination of multilayers from collagen type I and chondroitin sulfate with novel cationic liposomes.

Cationic liposomes composed of a novel lipid (N-{6-amino-1-[N-(9Z) -octadec9-enylamino] -1-oxohexan-(2S) -2-yl} –N’- {2- [N, N-bis(2-aminoethyl) amino] ethyl} -2-hexadecylpropandiamide) (OO4) and dioleoylphosphatidylethanolamine (DOPE) possess high amounts of amino groups and are promising systems for lipofection. Moreover, these cationic liposomes can also be used as a polycationic entity in multilayer formation using layer-by-layer technique (LbL), which is a method to fabricate surface coatings by alternating adsorption of polyanions and polycations. Since liposomes are suitable for endocytosis by or fusion with cells, controlled release of their cargo on site is possible. Here, a polyelectrolyte multilayer (PEM) system was designed of chondroitin sulfate (CS) and collagen type I (Col I) by LbL technique with OO4/DOPE liposomes embedded in the terminal layers to create an osteogenic microenvironment. Both, the composition of PEM and cargo of the liposomes were used to promote osteogenic differentiation of C2C12 myoblasts as in vitro model. The internalization of cargo-loaded liposomes from the PEM into C2C12 cells was studied using lipophilic (Rhodamine-DOPE conjugate) and hydrophilic (Texas Red–labeled dextran) model compounds. Besides, the use of Col I and CS should mimic the extracellular matrix of bone for future applications such as bone replacement therapies. Physicochemical studies of PEM were done to characterize the layer growth, thickness, and topography. The adhesion of myoblast cells was also evaluated whereby the benefit of a cover layer of CS and finally Col I above the liposome layer was demonstrated. As proof of concept, OO4/DOPE liposomes were loaded with dexamethasone, a compound that can induce osteogenic differentiation. A successful induction of osteogenic differentiation of C2C12 cells with the novel designed liposome-loaded PEM system was shown. These findings indicate that designed OH4/DOPE loaded PEMs have a high potential to be used as drug delivery or transfection system for implant coating in the field of bone regeneration and other applications.

In vitro evaluation of drug release and antibacterial activity of a silver-loaded wound dressing coated with a multilayer system

The goal of the study was to elaborate an antibacterial silver wound dressing covered by a protective coating that would prevent silver diffusion toward skin without losing its biocide properties. Therefore, non woven polyethyleneterephtalate (PET) textiles were pre-treated by two types of polysaccharides – chitosan and cyclodextrin – both crosslinked with citric acid by a pad/dry/cure process. Both types of resulting thermofixed textiles carrying the citrate crosslinks were then impregnated in silver solution followed by a thermal treatment and were finally coated by Layer-by-Layer (L-b-L) deposition of a polyelectrolyte multilayer (PEM) film consisting of anionic water-soluble poly-cyclodextrin and cationic chitosan. The influence of the process parameters was investigated in terms of silver adsorption capacity, PEM system build-up, silver kinetics of release and antibacterial activity. We demonstrate i) the utility of the intermediate thermal treatment step in the reduction of silver leakage in the polyelectrolyte solutions used in the L-b-L process, ii) that silver adsorption on the preliminary thermofixed layers did not affect the PEM system build-up, iii) the slowing down of silver release kinetic thanks to the PEM coating, iv) the preservation of the antibacterial activity despite the PEM coating.

Cross-linking multilayers of poly-l-lysine and hyaluronic acid: Effect on mesenchymal stem cell behavior.

Cells possess a specialized machinery through which they can sense physical as well as chemical alterations in their surrounding microenvironment that affect their cellular behavior. In this study, we aim to establish a polyelectrolyte multilayer system of 24 layers of poly-l-lysine and hyaluronic acid to control stem cell response after chemical cross-linking. The multilayer build-up process is monitored using different methods, which show that the studied polyelectrolyte multilayer system grows exponentially following the islands and islets theory. Successful chemical cross-linking is monitored by an increased zeta potential toward negative magnitude and an extraordinary growth in thickness. Human adipose-derived stem cells are used here and a relationship between cross-linking degree and cell spreading is shown as cells seeded on higher cross-linked polyelectrolyte multilayer show enhanced spreading. Furthermore, cells that fail to establish focal adhesions on native and low cross-linked polyelectrolyte multilayer films do not proliferate to a high extent in comparison to cells seeded on highly cross-linked polyelectrolyte multilayer, which also show an increased metabolic activity. Moreover, this study shows the relation between cross-linking degree and human adipose-derived stem cell lineage commitment. Histological staining reveals that highly cross-linked polyelectrolyte multilayers support osteogenic differentiation, whereas less cross-linked and native polyelectrolyte multilayers support adipogenic differentiation in the absence of any specific inducers. Owing to the precise control of polyelectrolyte multilayer properties such as potential, wettability, and viscoelasticity, the system presented here offers great potential for guided stem cell differentiation in regenerative medicine, especially in combination with materials exhibiting a defined surface topography.

Formation and enzymatic degradation of poly-l-arginine/fucoidan multilayer films

A polyelectrolyte multilayer (PEM) system based on biopolymers has been constructed and studied in its formation and enzymatic breakdown. The multilayer is composed of fucoidan (a proven antimicrobial/anti-inflammatory seaweed-based polysaccharide) and poly-l-arginine (a polypeptide that can be readily degraded with trypsin to yield arginine, a known NO donor), thus making the multilayer a potential dual action surface treatment for wound dressings. Studies on the formation of the multilayer revealed that the film built-up in the expected stepwise manner with consistent reversal of the zeta potential upon the adsorption of each subsequent polyion. The completed film (8 bilayers) was seen to have low hydration (30% water), as determined by H2O/D2O solvent replacement studies using the quartz crystal microbalance, with an adsorbed mass (without hydration water) of approx. 4.8μgcm−2, as determined by quantitative attenuated total reflectance Fourier transform infrared (ATR FTIR) spectroscopy. The enzymatic breakdown of the film in response to exposure to trypsin was also investigated, and the film was seen to release both polymers over time, with a projected complete film removal period of approximately 24h. Critically, this information was determined using ATR FTIR spectroscopy experiments, which allowed unambiguous deconvolution of the removal rates of the two polyions, which is information that cannot be obtained from other methodologies used to study enzymatic breakdown of surface films.

Effect of Polyelectrolyte Multilayers Assembled on Ordered Nanostructures on Adhesion of Human Fibroblasts.

Nanosphere lithography (NSL) and the layer-by-layer (LbL) technique are combined here for the first time to design a flexible system to achieve nanotopographical control of cell adhesion. NSL is used to generate regular patterns of tetrahedral gold nanodots of different size and distance. Besides the change in topography, LbL is used to generate a polyelectrolyte multilayer (PEM) system consisting of heparin (HEP) and poly(ethylene imine) (PEI) on top of the gold dots. The localized formation of PEM on gold dots is achieved by prior passivation of the surrounding silicon or glass surface. Properties of PEM are changed by adjusting the pH value of HEP solution to either acidic or alkaline values. Studies with human dermal fibroblasts (HDF) reveal that cells spread to a higher extent on PEM formed at pH 5.0 in dependence on the structure dimension. Further, filopodia formation is highly increased in cells on nanostructures exhibiting HEP as a terminal layer. The new system offers a great potential to guide stem cell differentiation in the future owing to its high degree of chemical and topographical heterogeneity.

Molecular composition of GAG-collagen I multilayers affects remodeling of terminal layers and osteogenic differentiation of adipose-derived stem cells

The effect of molecular composition of multilayers, by pairing type I collagen (Col I) with either hyaluronic acid (HA) or chondroitin sulfate (CS) was studied regarding the osteogenic differentiation of adhering human adipose-derived stem cells (hADSCs). Polyelectrolyte multilayer (PEM) formation was based primarily on ion pairing and on additional intrinsic cross-linking through imine bond formation with Col I replacing native by oxidized HA (oHA) or CS (oCS). Significant amounts of Col I fibrils were found on both native and oxidized CS-based PEMs, resulting in higher water contact angles and surface potential under physiological condition, while much less organized Col I was detected in either HA-based multilayers, which were more hydrophilic and negatively charged. An important finding was that hADSCs remodeled Col I at the terminal layers of PEMs by mechanical reorganization and pericellular proteolytic degradation, being more pronounced on CS-based PEMs. This was in accordance with the higher quantity of Col I deposition in this system, accompanied by more cell spreading, focal adhesions (FA) formation and significant α2β1 integrin recruitment compared to HA-based PEMs. Both CS-based PEMs caused also an increased fibronectin (FN) secretion and cell growth. Furthermore, significant calcium phosphate deposition, enhanced ALP, Col I and Runx2 expression were observed in hADSCs on CS-based PEMs, particularly on oCS-containing one. Overall, multilayer composition can be used to direct cell-matrix interactions, and hence stem cell fates showing for the first time that PEMs made of biogenic polyelectrolytes undergo significant remodeling of terminal protein layers, which seems to enable cells to form a more adequate extracellular matrix-like environment. Statement of SignificanceNatural polymer derived polyelectrolyte multilayers (PEMs) have been recently applied to adjust biomaterials to meet specific tissue demands. However, the effect of molecular composition of multilayers on both surface properties and cellular response, especially the fate of human adipose derived stem cells (hADSCs) upon osteogenic differentiation has not been studied extensively, yet. In addition, no studies exist that investigate a potential cell-dependent remodeling of PEMs made of extracellular matrix (ECM) components like collagens and glycosaminoglycans (GAGs). Furthermore, there is no knowledge whether the ability of cells to remodel PEM components may provide an added value regarding cell growth and differentiation. Finally, it has not been explored yet, how intrinsic cross-linking of ECM derived polyelectrolytes that improve the stability of PEMs will affect the differentiation potential of hADSCs. The current work aims to address these questions and found that the type of GAG has a strong effect on properties of multilayers and osteogenic differentiation of hADSCs. Additionally, we also show for the first time that PEMs made of biogenic polyelectrolytes undergo significant remodeling of terminal layers as completely new finding, which allows cells to form an ECM-like environment supporting differentiation upon osteogenic lineage. The finding of this work may open new avenues of application of PEM systems made by layer by layer (LbL) technique in tissue engineering and regenerative medicine.

Calcium phosphate/polyelectrolyte multilayer coatings for sequential delivery of multiple growth factors

Event Abstract Back to Event Calcium phosphate/polyelectrolyte multilayer coatings for sequential delivery of multiple growth factors Emily Jacobs1, 2, Marja Hurley3, Gloria Gronowicz3 and Liisa T. Kuhn1, 2 1 UConn, Biomedical Engineering, United States 2 UConn Health, Reconstructive Sciences, United States 3 UConn Health, School of Medicine, United States Introduction: Many of the most promising strategies for regenerative tissue-engineering aim to replicate natural cellular microenvironments using biomimetic, resorbable materials capable of growth factor delivery. Combinations of growth factors synergistically enhance tissue regeneration[1], but require sequential, rather than co-delivery delivery for maximum efficacy. Polyelectrolyte multilayer (PEM) coatings retain growth factor activity, however, staggered, sequential delivery from these coatings requires barrier layers to prevent interlayer diffusion of multiple factors that results in co-delivery. Here we demonstrate that the incorporation of a biomimetic calcium phosphate (bCaP) layer into PEM can prevent interlayer diffusion of biomolecules and enable staggered delivery. This modified PEM system is one of few aqueous, low temperature systems available for sequential, multifactor delivery and has potential to significantly impact the regenerative tissue-engineering field. Methods: bCaP coatings were prepared on sandblasted, 22 mm, treated tissue culture plastic disks, (NUNC, Rochester, NY) using a simulated body fluid method[2]. The PEM coatings (8-30 bilayers) were applied on top of the bCaP layer by automated alternate 10 min dipping into 1 mg/ml poly L glutamic acid (-) or poly-L lysine (+) solutions (Sigma, St. Louis, MO) with saline rinses between. Coatings were characterized with x-ray diffraction and scanning electron microscopy. To demonstrate sequential delivery a combination of a proliferative factor, recombinant human fibroblast growth factor-2 (FGF-2) (150 ng/disk) (R & D Systems, Minneapolis, MN), and a cytotoxic factor antimycin A (AntiA) (213 μg/disk)(Sigma, St. Louis, MO) was used. In vitro cellular activity on the prepared coatings was assessed with MC3T3-E1 mouse calvarial osteoprogenitor cells (ATCC, Manassas, VA) seeded at 10 or 40 x 103 cells/cm2. Proliferative and cytotoxic effects were quantified using the LIVE/DEAD® assay (Invitrogen Life Technologies, Grand Island, NY). Statistical significances were determined by unpaired t-tests and one-way ANOVA with Tukey post-tests. Results: Uniform nanocrystalline coatings of bCaP (Fig. 1A) and bCaP plus 30 bilayers of PEM (CaP-PEM30) (Fig. 1B) on the disks were observed via SEM. MC3T3-E1s cultured directly on adsorbed AntiA with no bCaP or PEM coating (AntiA) resulted in 90% cell death on day 1 (Fig. 2A). MC3T3-E1s cultured on AntiA embedded under 8 bilayers of PEM (AntiA-PEM8) resulted in 47% cell death on day 1 due to diffusion of AntiA through PEM8. MC3T3-E1s cultured on AntiA embedded under bCaP and 8 bilayers of PEM (AntiA-CaP-PEM8) resulted in 15% cell death, significantly better than PEM only (p<0.001). These data demonstrate that the addition of bCaP to PEM coatings inhibits interlayer diffusion. Active FGF-2 was delivered from 30 bilayers of PEM above CaP (CaP-PEM30-FGF2) as demonstrated by a significant increase in MC3T3-E1 proliferation on day 1 as compared to cells cultured on the FGF-2-free control, (Fig. 2B). No growth factor release was detected by ELISA without cells present. Sequential access of cells to FGF-2 followed by AntiA was also demonstrated (Fig. 3A). On day 1, no differences were observed between CaP-PEM30-FGF2 and AntiA-CaP-PEM30-FGF2 indicating access to AntiA was successfully blocked by bCaP. On day 5 however, cell-mediated degradation of PEM30 and bCaP resulted in a significant decrease in LIVE staining between groups (Fig. 3A) indicating AntiA delivery. Conclusions: Addition of a bCaP barrier layer to a PEM delivery system prevents unwanted interlayer diffusion of embedded factors and enables cell-mediated sequential delivery of multiple factors. This technology can be utilized in multiple research applications where a sequential delivery profile activated by cell degradation of matrix is desired. Funding provided from NIH NIDCR R01DE021103

Ionic Driven Embedment of Hyaluronic Acid Coated Liposomes in Polyelectrolyte Multilayer Films for Local Therapeutic Delivery.

The ability to control the spatial distribution and temporal release of a therapeutic remains a central challenge for biomedical research. Here, we report the development and optimization of a novel substrate mediated therapeutic delivery system comprising of hyaluronic acid covalently functionalized liposomes (HALNPs) embedded into polyelectrolyte multilayer (PEM) platform via ionic stabilization. The PEM platform was constructed from sequential deposition of Poly-L-Lysine (PLL) and Poly(Sodium styrene sulfonate) (SPS) “(PLL/SPS)4.5” followed by adsorption of anionic HALNPs. An adsorption affinity assay and saturation curve illustrated the preferential HALNP deposition density for precise therapeutic loading. (PLL/SPS)2.5 capping layer on top of the deposited HALNP monolayer further facilitated complete nanoparticle immobilization, cell adhesion, and provided nanoparticle confinement for controlled linear release profiles of the nanocarrier and encapsulated cargo. To our knowledge, this is the first study to demonstrate the successful embedment of a translatable lipid based nanocarrier into a substrate that allows for temporal and spatial release of both hydrophobic and hydrophilic drugs. Specifically, we have utilized our platform to deliver chemotherapeutic drug Doxorubicin from PEM confined HALNPs. Overall, we believe the development of our HALNP embedded PEM system is significant and will catalyze the usage of substrate mediated delivery platforms in biomedical applications.

Improved stability and cell response by intrinsic cross-linking of multilayers from collagen I and oxidized glycosaminoglycans.

Stability of surface coatings against environmental stress, such as pH, high ionic strength, mechanical forces, and so forth, is crucial for biomedical application of implants. Here, a novel extracellular-matrix-like polyelectrolyte multilayer (PEM) system composed of collagen I (Col I) and oxidized glycosaminoglycans (oGAGs) was stabilized by intrinsic cross-linking due to formation of imine bonds between aldehydes of oxidized chondroitin sulfate (oCS) or hyaluronan (oHA) and amino groups of Col I. It was also found that Col I contributed significantly more to overall mass in CS-Col I than in HA-Col I multilayer systems and fibrillized particularly in the presence of native and oxidized CS. Adhesion and proliferation studies with murine C3H10T1/2 embryonic fibroblasts demonstrated that covalent cross-linking of oGAG with Col I had no adverse effects on cell behavior. By contrast, it was found that cell size and polarization was more pronounced on oGAG-based multilayer systems, which corresponded also to the higher stiffness of cross-linked multilayers as observed by studies with quartz crystal microbalance (QCM). Overall, PEMs prepared from oGAG and Col I give rise to stable PEM constructs due to intrinsic cross-linking that may be useful for making bioactive coatings of implants and tissue engineering scaffolds.

Assembly of polyelectrolyte multilayer films on supported lipid bilayers to induce neural stem/progenitor cell differentiation into functional neurons.

The key factors affecting the success of neural engineering using neural stem/progenitor cells (NSPCs) are the neuron quantity, the guidance of neurite outgrowth, and the induction of neurons to form functional synapses at synaptic junctions. Herein, a biomimetic material comprising a supported lipid bilayer (SLB) with adsorbed sequential polyelectrolyte multilayer (PEM) films was fabricated to induce NSPCs to form functional neurons without the need for serum and growth factors in a short-term culture. SLBs are suitable artificial substrates for neural engineering due to their structural similarity to synaptic membranes. In addition, PEM film adsorption provides protection for the SLB as well as the ability to vary the surface properties to evaluate the effects of physical and mechanical signals on NSPC differentiation. Our results revealed that NSPCs were inducible on SLB-PEM films consisting of up to eight alternating layers. In addition, the process outgrowth length, the percentage of differentiated neurons, and the synaptic function were regulated by the number of layers and the surface charge of the outermost layer. The average process outgrowth length was greater than 500 μm on SLB-PLL/PLGA (n = 7.5) after only 3 days of culture. Moreover, the quantity and quality of the differentiated neurons were obviously enhanced on the SLB-PEM system compared with those on the PEM-only substrates. These results suggest that the PEM films can induce NSPC adhesion and differentiation and that an SLB base may enhance neuron differentiation and trigger the formation of functional synapses.

CHIRAL SEPARATIONS USING HEPARIN AND POLYELECTROLYTE MULTILAYERS IN CAPILLARY ELECTROPHORESIS

Reports on the use of heparin as a chiral additive show widely different separation conditions and inconsistent results. A systematic evaluation of the separation of pheniramine enantiomers using heparin as a chiral selector suggested that heparin was interacting with the capillary surface at acidic pH. Further testing confirmed the interaction between heparin and the capillary surface at acidic pH causing an increase in the electroosmotic flow (EOF). Polyelectrolyte multilayer (PEM) was chosen as a potential means to eliminate the interaction between heparin and the capillary surface. Generation of the PEMs on a bare capillary was monitored by measuring the changes in EOF following the deposition of each polyelectrolyte layer; deposition provided consistent EOF intensities and facilitated control over EOF direction. Results from this study indicated that a stable PEM system could be generated, which prevents the interaction of heparin with the capillary surface. This PEM system showed excellent reproducibility, with only a slight loss of resolution due to the increased interactions between the analyte and the charged capillary wall.

Layer-by-layer assembly of polymersomes and polyelectrolytes on planar surfaces and microsized colloidal particles

Hybrid polyelectrolyte multilayer systems were fabricated on top of planar surfaces and colloidal particles via layer by layer (LbL) assembly of polystyrene sulphonate (PSS) and polybenzyl methacrylate-block-poly(dimethylamino)ethyl methacrylate (PBzMA-b-PDMAEMA) polymersomes. Polymersomes were prepared by self assembly of PBzMA-b-PDMAEMA copolymer, synthesised by group transfer polymerisation. Polymersomes display a diameter of 270nm and a shell thickness of 11nm. Assembly on planar surfaces was followed by means of the Quartz Crystal Microbalance with Dissipation (QCM-D) and Atomic Force Microscopy (AFM). Detailed information on the assembly mechanism and surface topology of the polymersome/polyelectrolyte films was thereby obtained. The assembly of polymersomes and PSS on top of silica particles of 500nm in diameter was confirmed by ζ-potential measurements. Confocal laser scanning microscopy (CLSM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) revealed that polymersome/PSS coated silica particles increase in total diameter up to 3–5μm. This hints toward the formation of densely packed polymersome layers. In addition, CLSM showed that polymersome/PSS films exhibit a high loading capacity that could potentially be used for encapsulation and delivery of diverse chemical species. These results provide an insight into the formation of multilayered films with compartmentalised hydrophilic/hydrophobic domains and may lead to the successful application of polymersomes in surface-engineered colloidal systems.

Characterizing Ultrathin and Thick Organic Layers by Surface Plasmon Resonance Three-Wavelength and Waveguide Mode Analysis

A three-wavelength angular-scanning surface plasmon resonance based analysis has been utilized for characterizing optical properties of organic nanometer-thick layers with a wide range of thicknesses. The thickness and refractive index were determined for sample layers with thicknesses ranging from subnanometer to hundreds of nanometers. The analysis approach allows for simultaneous determination of both the refractive index and thickness without prior knowledge of either the refractive index or the thickness of the sample layers and without the help of other instruments, as opposed to current methods and approaches for characterizing optical properties of organic nanometer-thick layers. The applicability of the three-wavelength angular-scanning surface plasmon resonance approach for characterizing thin and thick organic layers was demonstrated by ex situ deposited mono- and multilayers of stearic acid and hydrogenated soy phosphatidylcholine and in situ layer-by-layer deposition of two different polyelectrolyte multilayer systems. In addition to the three-wavelength angular-scanning surface plasmon resonance approach, another surface plasmon resonance optical phenomenon, i.e., the surface plasmon resonance waveguide mode, was utilized to characterize organic sample layers whose thicknesses border the micrometer scale. This was demonstrated by characterizing both in situ layer-by-layer deposited polyelectrolyte multilayer systems and an ex situ deposited spin-coated polymer layer.

Adsorbate–Metal Bond Effect on Empirical Determination of Surface Plasmon Penetration Depth

The penetration depth of surface plasmons is commonly determined empirically from the observed response for adsorbate loading on gold surface plasmon resonance (SPR) substrates. However, changes in the SPR spectrum may originate from both changes in the effective refractive index near the metal surface and changes in the metal permittivity following covalent binding of the adsorbate layer. Herein, the significance of incorporating an additional adsorbate-metal bonding effect in the calculation is demonstrated in theory and in practice. The bonding effect is determined from the nonzero intercept of a SPR shift versus adsorbate thickness calibration and incorporated into the calculation of penetration depth at various excitation wavelengths. Determinations of plasmon penetration depth with and without the bonding response for alkanethiolate-gold are compared and are shown to be significantly different for a thiol monolayer adsorbate system. Additionally, plasmon penetration depth evaluated with bonding effect compensation shows greater consistency over different adsorbate thicknesses and better agreement with theory derived from Maxwell's equation, particularly for adsorbate thicknesses that are much smaller (<5%) than the plasmon penetration depth. The method is also extended to a more practically applicable polyelectrolyte multilayer adsorbate system.