Polydimethylsiloxane Surface Research Articles

Texture-structure-based liquid metal filling for blind-end microchannels and its application on multi-layer chips.

This research work reports a novel method to achieve fast liquid metal (LM) injection in blind-end microchannels which is especially suitable for multi-layer microfluidic chips. This method is based on a texture-like surface bonding technology. The texture-like surface is fabricated on a polydimethylsiloxane (PDMS) slab with standard soft-lithography technology and bonded with another PDMS slab with microelectrode patterns on it. When injected with LM, the texture-like structure can prevent the LM from entering but allows the air inside to be released during the injection to achieve perfect blind-end complex LM electrodes. The experimental results show that it can achieve fast and perfect LM injection in the blind-end pattern and can also prevent the large area of the flat chamber from collapsing during bonding. We also parametrically studied the texture structure's size for bonding strength between the texture structure and the blank PDMS surface. In addition, we integrate three layers of blind-end complex liquid metal patterns into one multi-layer chip using this technology and later use this structure to realize series connection of two LM-based electroosmotic micropumps (EOP). Compared with the conventional LM-based EOP, the structure of the EOP chip was greatly simplified and resulted in a higher level of integration.

Fabrication of a Gelatin-Based Microdevice for Vascular Cell Culture.

This study presents a novel technique for fabricating microfluidic devices with microbial transglutaminase-gelatin gels instead of polydimethylsiloxane (PDMS), in which flow culture simulates blood flow and a capillary network is incorporated for assays of vascular permeability or angiogenesis. We developed a gelatin-based device with a coverslip as the bottom, which allows the use of high-magnification lenses with short working distances, and we observed the differences in cell dynamics on gelatin, glass, and PDMS surfaces. The tubes of the gelatin microfluidic channel are designed to be difficult to pull out of the inlet hole, making sample introduction easy, and the gelatin channel can be manipulated from the cell introduction to the flow culture steps in a manner comparable to that of a typical PDMS channel. Human umbilical vein endothelial cells (HUVECs) and normal human dermal fibroblasts (NHDFs) were successfully co-cultured, resulting in structures that mimicked blood vessels with inner diameters ranging from 10 µm to 500 µm. Immunostaining and scanning electron microscopy results showed that the affinity of fibronectin for gelatin was stronger than that for glass or PDMS, making gelatin a suitable substrate for cell adhesion. The ability for microscopic observation at high magnification and the ease of sample introduction make this device easier to use than conventional gelatin microfluidics, and the above-mentioned small modifications in the device structure are important points that improve its convenience as a cell assay device.

Solid‐phase extraction based on PDMS/ionic liquid sponge followed by gas chromatography–mass spectrometry for rapid and sensitive determination of volatile components in lavender

Due to the complexity and the low concentrations of volatile components in aromatic plants, sample pretreatment is an important step in the whole analytical procedure. This study aimed to propose a novel, sensitive and fast approach to determine the volatile components in lavender. The 1-butyl-3-(propyltrimethoxysilane)imidazolium chloride ([BPtmsim]Cl) ionic liquid was introduced onto the surface of polydimethylsiloxane (PDMS) to prepare a novel PDMS/[BPtmsim]Cl sponge with large surface area, good sorption performance, and reusability. A solid-phase extraction method was developed based on PDMS/[BPtmsim]Cl sponge combined with gas chromatography-mass spectrometry (GC-MS). The effects of the various experimental parameters on the extraction efficiency were investigated. The optimal conditions were [BPtmsim]Cl amount of 0.3g, 1:4 as the mass ratio of PDMS/[BPtmsim]Cl to lavender sample, microwave power of 700 W, microwave time of 10min, and n-hexane as the desorption solvent. The method validation results showed good linearity (10-800 μg/ml), high correlation coefficient (R2 ≥ 0.9991), low limits of detection (1.73-2.50 ng/μl), and limits of quantification (4.10-5.11 ng/μl). The interday and intraday precision with relative standard deviation (RSD) values were below 1.93% and 4.71%, respectively. Under the optimal extraction conditions, 16 lavender samples from three different species were analysed and a total of 57 volatile compounds were identified. The correlation between different species of lavender and volatile components was explored using principal component analysis (PCA) and partial least squares-discriminant analysis (PLS-DA). The results showed that PDMS/[BPtmsim]Cl extraction is a rapid, highly efficient, and sensitive technique for the determination of volatile components in complex plant samples.

Engineered Sandwich-Structured Composite Wound Dressings with Unidirectional Drainage and Anti-Adhesion Supporting Accelerated Wound Healing.

Proper management of exudate is of great clinical value for reducing wound infection and promoting wound healing, thus various dressings have been studied to address this widespread medical challenge. Herein, a novel sandwich-structured composite wound dressing (SCWD), integrating of a superlyophobic (SLO) polydimethylsiloxane (PDMS) layer, a superlyophilic gauze layer, and a lyophobic PDMS layer is presented, with particular unidirectional droplet drainage and stable anti-adhesion capabilities, which realizes effective management of wound exudate and provides a favorable environment for wound healing. Thanks to the stable SLO property on the PDMS surface with hierarchical micro/nanostructures, the continuously accumulated wound exudate at the interface between dressing and wound surface is gradually deformed, eventually passing through SLO PDMS layer through milli-scale channels and being absorbed by gauze layer. Experimental results show that the application of SCWD can significantly reduce the occurrence of wound infection, avoid the tearing of wound tissues when replacing dressings, and accelerate wound healing by ≈20%. The combination of SCWD and lyophilized powders of stem cells supernatant (LPSCS) is verified to better accelerate the healing process. The proposed method offers great potential in clinical applications, particularly for acute trauma wound treatments.

Mitigation of Cellular and Bacterial Adhesion on Laser Modified Poly (2-Methacryloyloxyethyl Phosphorylcholine)/Polydimethylsiloxane Surface

Nowadays, using polymers with specific characteristics to coat the surface of a device to prevent undesired biological responses can represent an optimal strategy for developing new and more efficient implants for biomedical applications. Among them, zwitterionic phosphorylcholine-based polymers are of interest due to their properties to resist cell and bacterial adhesion. In this work, the Matrix-Assisted Laser Evaporation (MAPLE) technique was investigated as a new approach for functionalising Polydimethylsiloxane (PDMS) surfaces with zwitterionic poly(2-Methacryloyloxyethyl-Phosphorylcholine) (pMPC) polymer. Evaluation of the physical-chemical properties of the new coatings revealed that the technique proposed has the advantage of achieving uniform and homogeneous stable moderate hydrophilic pMPC thin layers onto hydrophobic PDMS without any pre-treatment, therefore avoiding the major disadvantage of hydrophobicity recovery. The capacity of modified PDMS surfaces to reduce bacterial adhesion and biofilm formation was tested for Gram-positive bacteria, Staphylococcus aureus (S. aureus), and Gram-negative bacteria, Escherichia coli (E. coli). Cell adhesion, proliferation and morphology of human THP-1 differentiated macrophages and human normal CCD-1070Sk fibroblasts on the different surfaces were also assessed. Biological in vitro investigation revealed a significantly reduced adherence on PDMS-pMPC of both E. coli (from 29 × 10 6 to 3 × 102 CFU/mL) and S. aureus (from 29 × 106 to 3 × 102 CFU/mL) bacterial strains. Additionally, coated surfaces induced a significant inhibition of biofilm formation, an effect observed mainly for E. coli. Moreover, the pMPC coatings improved the capacity of PDMS to reduce the adhesion and proliferation of human macrophages by 50% and of human fibroblast by 40% compared to unmodified scaffold, circumventing undesired cell responses such as inflammation and fibrosis. All these highlighted the potential for the new PDMS-pMPC interfaces obtained by MAPLE to be used in the biomedical field to design new PDMS-based implants exhibiting long-term hydrophilic profile stability and better mitigating foreign body response and microbial infection.

Magnetically controlled super-wetting surface switching between ultra-low and ultra-high droplet adhesion

Controlled liquid adhesion behaviors on super-wetting surfaces have gained significant attention, however, precise controlling of adhesion behavior is extremely hard to realize due to some inherent limitation in surface chemistry or morphology. Herein, we report a silicone-oil-infused magnetic porous polydimethylsiloxane (SMPP) surface with magnetically tunable super-wetting behaviors. Benefiting from the magnetic-field-responsive structure and interconnected porous characteristics, the SMPP can use magnetic field to control the seepage and absorption of silicone oil in the micropore channels, thereby precisely changing the adhesion of the water droplets on the surface. Compared to conventional super-wetting surfaces, this SMPP surface displays reversible in-situ conversion from ultra-high to ultra-low droplet adhesion with sliding angles ranging from 3° to 180° that hold up well even after severe cutting or abrasion. We also demonstrated that this tunable adhesion behavior can be used not only to enhance droplet manipulation in spatiotemporal but also to design unique microfluidic microreactors and antigravity transport devices. We envision that this proof-in-concept surface can serve as an important component of integrated control systems for intelligent manipulators, biochemical reactions, fluid transport, and biomedical analysis.

Friction Property of Hierarchical Micro/Nanopatterned PDMS.

Polydimethylsiloxane (PDMS) has many advantages, but the friction coefficient generated by contact with the counter material is high. The purpose of this study is to reduce the friction coefficient by forming hierarchical micro/nanopatterns on the PDMS surface using the imprinting method. In addition, the optimum conditions for reducing the friction coefficient by controlling the sliding speed and normal load were determined. After contacting flat bare PDMS and hierarchical micro/nanostructured PDMS with a counter tip made of polyurethane (PU), the change in friction with sliding speed and vertical load was evaluated. Under normal load conditions, the average friction coefficient of the bare PDMS decreased as the sliding speed increased, and that of the patterned PDMS slightly increased. Regardless of the sliding speed, the friction coefficient decreased as the normal load increased for both specimens. At a sliding speed of 4 mm/s under a load of 10 mN, the friction reduction effect of the pattern structure was the largest at 79%. Overall, the greatest friction reduction effect (84%) was confirmed in patterned PDMS with the lowest friction coefficient under the conditions of 4 mm/s, 50 mN, compared to bare PDMS with the highest friction coefficient under the conditions of 4 mm/s, 10 mN.

In situ synthesis of low-cost NELIBS substrate for rapid detection of ultra-low trace elements in liquid samples

Nanoparticle Enhanced LIBS is one of the most powerful and emerging techniques with high sensitivity for trace element analysis and finding increasing applications in various fields of analytical chemistry. Despite many efforts being put forward for the design of NELIBS substrate, it remains a great challenge for developing a highly sensitive substrate that could be helpful for environmental and biological applications. In this work, we report our attempt to improve the detection sensitivity by developing a facile and versatile method capable of generating silver nanoparticles in-situ on the surface of poly dimethyl siloxane (PDMS) in a simple, cost-effective, and additional capping agent free-way. The prepared Ag-decorated PDMS substrate exhibits excellent sensitivity at extremely low concentrations enabling the detection of Cu, Pb, and Cd at a concentration as low as sub ppb levels. Analytical prediction capabilities of this technique was validated using leave one out method and results show interesting possibilities.

The effect of scalable PDMS gas-entrapping microstructures on the dynamics of a single cavitation bubble

The effect of gas-entrapping polydimethylsiloxane (PDMS) microstructures on the dynamics of cavitation bubbles laser-induced next to the PDMS surface is investigated and compared against the cavitation dynamics next to a flat smooth boundary. Local pressure gradients produced by a cavitation bubble cause the air pockets entrapped in the PDMS microstructures to expand and oscillate, leading to a repulsion of the cavitation bubble. The microstructures were fabricated as boxed crevices via a simple and scalable laser ablation technique on cast acrylic, allowing for testing of variable structure sizes and reusable molds. The bubble dynamics were observed using high speed photography and the surrounding flows were visualized and quantified using particle tracking velocimetry. Smaller entrapped air pockets showed an enhanced ability to withstand deactivation at three stand-off distances and over 50 subsequent cavitation events. This investigation provides insight into the potential to direct the collapse of a cavitation bubble away from a surface to mitigate erosion or to enhance microfluidic mixing in low Reynolds number flows.

Soft surfaces induce neural differentiation via the neuron restrictive silencer factor

The physical and mechanical environment influence the differentiation and culture of stem cells. Early research in this field showed that mesenchymal stem cells (MSCs) adopt preferential lineages when cultured on surfaces of varying stiffness. Culture on very soft surfaces promoted neural differentiation. This effect has been observed in mesenchymal and embryonic stem cells and was shown to increase development of neural stem cells. However, providing further information on the molecular characterization of this phenomenon could help to guide the development of materials that enhance neural differentiation. Previously, our laboratory showed that chemical cues, forskolin and IBMX, induced neural differentiation of MSCs by downregulating the Neuron Restrictive Silencer Factor, leading to de-repression of neural gene expression. We sought to determine if the mechanism whereby soft surfaces induce neural differentiation could also involve NRSF function. We show that MSCs cultured on soft polydimethylsiloxane (PDMS) surfaces have reduced expression of NRSF as well as altered localization of NRSF. This suggests the modulation of transcription factors by surface substrate could be capitalized upon in designing materials for neural cell culture.

Design and evaluation of micro-sized glass bubble embedded PDMS composite for application to haptic forceps

The purpose of this study was to improve the durability and gripping performance of haptic forceps without damaging the counter materials. Glass bubbles (GBs) were embedded on the surface of polydimethylsiloxane (PDMS) to form a GB embedded PDMS (GBEP) composite, and then coated on the gripping part of the haptic forceps. The PDMS base and a curing agent were mixed with various precuring times, and the degree of embedding of GBs on the PDMS surface was controlled. As the precuring time increased, the depth of the GBs embedded in the PDMS surface decreased significantly. The friction coefficients of the GBEP specimens were lower than those of the bare PDMS. Bare PDMS and GBEP specimens with long precuring times were severely damaged, whereas GBEP specimens with short precuring times were relatively less damaged. When deionized (DI) water-based lubricants containing surfactants in various weight ratios were used, the friction coefficient of the specimens significantly decreased compared with dry or DI water lubrication conditions. Although the counter material was severely damaged by uncoated haptic forceps, it was not damaged by PDMS and GBEP coated haptic forceps, respectively. The durability of GBEP was superior to that of bare PDMS, and GBEP coated haptic forceps maintained gripping performance.

Multifunctional Surface Modification of PDMS for Antibacterial Contact Killing and Drug-Delivery of Polar, Nonpolar, and Amphiphilic Drugs.

Medical device-associated infections pose major clinical challenges that emphasize the need for improved anti-infective biomaterials. Polydimethylsiloxane (PDMS), a frequently used elastomeric biomaterial in medical devices, is inherently prone to bacterial attachment and associated infection formation. Here, PDMS surface modification strategy is presented consisting of a cross-linked lyotropic liquid crystal hydrogel microparticle coating with antibacterial functionality. The microparticle coating composed of cross-linked triblock copolymers (diacrylated Pluronic F127) was deposited on PDMS by physical immobilization via interpenetrating polymer network formation. The formed coating served as a substrate for covalent immobilization of a potent antimicrobial peptide (AMP), RRPRPRPRPWWWW-NH2, yielding high contact-killing antibacterial effect against Staphylococcus epidermidis and Staphylococcus aureus. Additionally, the coating was assessed for its ability to selectively host polar, amphiphilic, and nonpolar drugs, resulting in sustained release profiles. The results of this study put forward a versatile PDMS modification strategy for both contact-killing antibacterial surface properties and drug-delivery capabilities, offering a solution for medical device-associated infection prevention.

Contact line dynamics of a water drop spreading over a textured surface in the electrowetting-on-dielectric configuration.

Modeling the electrowetting process of a liquid droplet placed on a hydrophobic surface in an ambient environment has several challenges over and above those of basic spreading [F. Mugele, Soft Matter 5, 3377 (2009)10.1039/b904493k]. At an external voltage below the value that causes contact angle saturation, transient spreading is augmented by contact angle reduction defined by the Young-Lippmann equation. In addition, the macroscopic equilibrium contact angle and, therefore, the spreading rate could be altered by the surface hysteresis. Beyond the saturation point, spreading reveals additional features of higher complexity [Q. Vo and T. Tran, J. Fluid Mech. 925, A19 (2021)10.1017/jfm.2021.677]. These details have been examined from experiments as well as numerical simulation in the present work. Below the saturation point, the contact angle model of Dwivedi etal. [Phys. Rev. Fluids 7, 034002 (2022)10.1103/PhysRevFluids.7.034002] with the correction related to the electric field is seen to be applicable. Beyond saturation, the experimentally determined instantaneous contact angle distribution shows two distinct functionalities with respect to the contact line velocity. The first prevails from the onset of spreading until the spreading factor attains a peak value. The second trend is initiated with the retraction of the contact line. Except for differences in parametric values, the form of the contact angle model remains unchanged. Simulations in the postsaturation regime are shown to match experimental data in terms of the transient spreading factor, drop shapes, and the instantaneous contact angle. The role of the ground wire is found to be important and the three-phase contact line formed on it has been included in simulations. Spreading dynamics of the droplet have also been studied when the ground wire is kept at a distance of 40 μm from the apex of the drop. Simulations as well as experiments, show the propagation of a capillary wave between the ground wire and the three-phase contact line. For spreading over an uncoated polydimethylsiloxane (PDMS) surface, the contact line is trapped at local pinning sites, leading to additional distortions in the instantaneous shapes acquired by the interface.

Elucidating the effect of tomato leaf surface microstructure on Botrytis cinerea using synthetic systems.

For some pathogenic fungi, sensing surface topography is part of their infection strategy. Their directional growth and transformation to a new developmental stage is influenced by contact with topographic features, which is referred to as thigmo-response, the exact functionality of which is not fully understood. Research on thigmo-responses is often performed on biomimetically patterned surfaces (BPS). Polydimethylsiloxane (PDMS) is especially suitable for fabrication of BPS. Here, we used synthetic BPS surfaces, mimicking tomato leaf surface, made from PDMS with the pathogenic fungus Botrytis cinerea to study the influence of structural features of the leaf surface on the fungus behavior. As a control, a PDMS surface without microstructure was fabricated to maintain the same chemical properties. Pre-penetration processes of B. cinerea, including the distribution of conidia on the surface, germination, and germ tube growth were observed on both leaf-patterned and flat PDMS. Microstructure affected the location of immediate attachment of conidia. Additionally, the microstructure of the plant host stimulated the development of germ tube in B. cinerea, at a higher rate than that observed on flat surface, suggesting that microstructure plays a role in fungus attachment and development.

Determination of the rate-dependent adhesion of polydimethylsiloxane using an atomic force microscope

A JKR (Johnson-Kendall-Roberts) formalism is used to extract the Young modulus, the contact radius, and the energy release rate simply from the retraction curve of a borosilicate glass colloidal probe from a polydimethylsiloxane (PDMS) surface using an atomic force microscope. PDMS samples ranged from perfectly elastic to those with incipient viscoelasticity. The dependence of the release rate energy with the crack speed is verified using a fracture mechanics-based method.

Bone surface mimicked PDMS membranes stimulate osteoblasts and calcification of bone matrix

Cellular microenvironments play a crucial role in cell behavior. In addition to the biochemical cues present in the microenvironments, biophysical and biomechanical properties on surfaces have an impact on cellular functionality and eventually cellular fate. Effects of surface topography on cell behavior are being studied extensively in the literature. However, these studies often try to replicate topographical features of tissue surfaces by using techniques such as chemical etching, photolithography, and electrospinning, which may result in the loss of crucial micro- and nano- features on the tissue surfaces such as bone. This study investigates the topographical effects of bone surface by transferring its surface features onto polydimethylsiloxane (PDMS) membranes using soft lithography from a bovine femur. Our results have shown that major features on bone surfaces were successfully transferred onto PDMS using soft lithography. Osteoblast proliferation and calcification of bone matrix have significantly increased along with osteoblast-specific differentiation and maturation markers such as osteocalcin (OSC), osterix (OSX), collagen type I alpha 1 chain (COL1A1), and alkaline phosphatase (ALP) on bone surface mimicked (BSM) PDMS membranes in addition to a unidirectional alignment of osteoblast cells compared to plain PDMS surfaces. This presented bone surface mimicking method can provide a versatile native-like platform for further investigation of intracellular pathways regarding osteoblast growth and differentiation.

Surface characterisation reveals substrate suitability for cyanobacterial phototaxis

Cyanobacteria respond to light stimulation, activating localised assembly of type IV pili for motility. The resulting phototactic response is highly dependent on the nature of the incoming light stimulus, and the final motility parameters depend on the surface properties. Conventionally, phototaxis studies are carried out on hydrogel surfaces, such as agarose, with surface properties that vary in time due to experimental conditions. This study considers five substrates, widely utilized in microfluidic technology, to identify the most suitable alternative for performing reliable and repeatable phototaxis assays. The surfaces are characterised via a contact angle goniometer to determine the surface energy, white light interferometry for roughness, zeta-potentials and AFM force distance curves for charge patterns, and XPS for surface composition. Cell motility assays showed 1.25 times increment on surfaces with a water contact angle of 80° compared to a reference glass surface. To prove that motility can be enhanced, polydimethylsiloxane (PDMS) surfaces were plasma treated to alter their surface wettability. The motility on the plasma-treated PDMS showed similar performance as for glass surfaces. In contrast, untreated PDMS surfaces displayed close to zero motility. We also describe the force interactions of cells with the test surfaces using DLVO (Derjaguin-Landau-Verwey-Overbeek) and XDLVO (extended DLVO) theories. The computed DLVO/XDLVO force-distance curves are compared with those obtained using atomic force microscopy. Our findings show that twitching motility on tested surfaces can be described mainly from adhesive forces and hydrophobicity/hydrophilicity surface properties. Statement of significanceThe current article focuses on unravelling the potential Micro-Electro-Mechanical System (MEMS) compatible surfaces for studying phototactic twitching motility of cyanobacteria. This is the first exhaustive surface characterization study coupled with phototaxis experiments, to understand the forces contributing to twitching motility. The methods shown in this paper can be further extended to study other surfaces and also to other bacteria exhibiting twitching motility.

Contraction pressure analysis using optical imaging in normal and MYBPC3-mutated hiPSC-derived cardiomyocytes grown on matrices with tunable stiffness

Current in vivo disease models and analysis methods for cardiac drug development have been insufficient in providing accurate and reliable predictions of drug efficacy and safety. Here, we propose a custom optical flow-based analysis method to quantitatively measure recordings of contracting cardiomyocytes on polydimethylsiloxane (PDMS), compatible with medium-throughput systems.Movement of the PDMS was examined by covalently bound fluorescent beads on the PDMS surface, differences caused by increased substrate stiffness were compared, and cells were stimulated with β-agonist. We further validated the system using cardiomyocytes treated with endothelin-1 and compared their contractions against control and cells incubated with receptor antagonist bosentan. After validation we examined two MYBPC3-mutant patient-derived cell lines.Recordings showed that higher substrate stiffness resulted in higher contractile pressure, while beating frequency remained similar to control. β-agonist stimulation resulted in both higher beating frequency as well as higher pressure values during contraction and relaxation. Cells treated with endothelin-1 showed an increased beating frequency, but a lower contraction pressure. Cells treated with both endothelin-1 and bosentan remained at control level of beating frequency and pressure. Lastly, both MYBPC3-mutant lines showed a higher beating frequency and lower contraction pressure.Our validated method is capable of automatically quantifying contraction of hiPSC-derived cardiomyocytes on a PDMS substrate of known shear modulus, returning an absolute value. Our method could have major benefits in a medium-throughput setting.

Wetting of aqueous sodium dodecyl sulfate droplets on polydimethylsiloxane surfaces during evaporation

Wetting of aqueous sodium dodecyl sulfate (SDS) droplets on polydimethylsiloxane (PDMS) surfaces during evaporation were experimentally studied. After a short-time spontaneous spreading, sessile droplets experienced a period of the constant contact radius (CCR) stage. And it was found that substrate elasticity was found to have an influence on the duration of the CCR stage during the evaporation of aqueous SDS droplets on PDMS surfaces. Moreover, a local contact angle minimum was found during the evaporation of aqueous SDS droplets with an initial SDS concentration below 0.5 CMC. A physical mechanism taking into account the structure of SDS molecules adsorbed at PDMS surfaces was developed for the occurrence of the CCR stage and the local contact angle minimum. Furthermore, two-third power of the instantaneous droplet volume nearly varies linearly with time for all cases.

High-Output Lotus-Leaf-Bionic Triboelectric Nanogenerators Based on 2D MXene for Health Monitoring of Human Feet.

As versatile energy harvesters, triboelectric nanogenerators (TENGs) have attracted considerable attention in developing portable and self-powered energy suppliers. The question of how to improve the output power of TENGs using cost-effective means is still under vigorous investigation. In this paper, high-output TENGs were successfully produced by using a simple and low-cost lotus-leaf-bionic (LLB) method. Well-distributed microstructures were fabricated via the LLB method on the surface of a polydimethylsiloxane (PDMS) negative triboelectric layer. 2D MXene (Ti3C2Tx) and graphene were doped into the structured PDMS to evaluate their effects on the performance of TENG. Owing to merits of the MXene doping and microstructures on the PDMS surface, the output power of MXene-doped LLB TENGs reached as high as 104.87 W/m2, which was about 10 times higher than that of graphene-doped devices. The MXene-doped LLB TENGs can be used as humidity sensors, with a sensitivity of 4.4 V per RH%. In addition, the MXene-doped LLB TENGs were also sensitive to human body motions; hence, a foot health monitoring system constructed by the MXene-doped LLB TENGs was successfully demonstrated. The results in this work introduce a way to produce cost-effective TENGs using bionic means and suggest the promising applications of TENGs in the smart monitoring system of human health.