PLLA Block Research Articles

Grafting of nonpolar polyisoprene as midblock and polar polylactide as outer block onto cellulose to produce bio-based thermoplastic elastomers

Sustainable cellulose-graft-diblock copolymers (cellulose-graft-polyisoprene-block-polylactide, MCC-g-PI-b-PLLA, MCC was chemically-modified microcrystalline cellulose) were designed and delicately synthesized for the first time by a mild and facile procedure via combining ring-opening polymerization and reversible addition-fragmentation chain transfer polymerization techniques, which conquered the difficulties in synthesis due to the distinct chemical properties among the MCC backbone, PI and PLLA blocks. Two separate glass transition temperatures were detected for MCC-g-PI-b-PLLA copolymers by differential scanning calorimetry, indicative of microphase separation, consistent with small-angle X-ray scattering and atomic force microscopy measurements. The α-form crystals of PLLA outer blocks were revealed by wide-angle X-ray diffraction measurement. The monotonic and step-cyclic tensile tests revealed that the mechanical property could be tuned by changing the molecular mass of PI midblock. The two ends of the soft PI midblock were anchored by rigid cellulose backbone and hard PLLA outer block, respectively, which served as physical crosslinking points. The rigid cellulose backbones brought the PI rubbery domains and PLLA hard domains together to form a whole hierarchical microstructure, endowing the copolymers with distinguished mechanical property. This work provided a feasible approach to producing environmental-friendly cellulose-based copolymers with fully biomass-derived feedstocks, having a profound impact on the development of sustainable polymer-based materials.

Vacuum-driven orientation of Nanostructured polystyrene-block-Poly(L-lactide) block copolymer thin films for Nanopatterning

Herein, we demonstrate a simple approach to control the orientation of cylinder-forming nanostructures in polystyrene-block-poly(L-lactide) (PS-b-PLLA) BCP thin films through thermal annealing under a high-vacuum environment. Surface tension discrepancy between the constituent blocks is critical in controlling the aimed orientation of self-assembled nanostructures in block copolymer (BCP) thin films. For BCP self-assembly, temperature has been widely utilized as a thermodynamic state variable under ambient pressure conditions, whereas the use of high vacuum (low pressure) for thermal annealing is limited. It has been observed that temperature can alter the surface tension only marginally with increasing temperature for polymeric materials; as a result, the pressure dependence of surface tension for PS and PLLA was investigated. By increasing the vacuum degree during thermal annealing, the surface tension discrepancy between the PS and PLLA blocks can be reduced significantly. Accordingly, during thermal annealing under high vacuum degree, a neutral air polymer interface can be generated for the BCP thin films, resulting in the formation of perpendicular cylinders from the neutral surface of the thin film through BCP microphase separation.

Combining Crystallization-Driven Self-Assembly with Reverse Sequence Polymerization-Induced Self-Assembly Enables the Efficient Synthesis of Hydrolytically Degradable Anisotropic Block Copolymer Nano-objects Directly in Concentrated Aqueous Media.

Herein we combine the well-known processing advantages conferred by polymerization-induced self-assembly (PISA) with crystallization-driven self-assembly (CDSA) to achieve the efficient synthesis of hydrolytically degradable, highly anisotropic block copolymer nano-objects directly in aqueous solution at 30% w/w solids. This new strategy involves a so-called reverse sequence PISA protocol that employs poly(l-lactide) (PLLA) as the crystallizable core-forming block and poly(N,N'-dimethylacrylamide) (PDMAC) as the water-soluble non-ionic coronal block. Such syntheses result in PDMAC-rich anisotropic nanoparticles. Depending on the target diblock copolymer composition, either rod-like nanoparticles or diamond-like platelets can be obtained. Furthermore, N-Acryloylmorpholine is briefly evaluated as an alternative hydrophilic vinyl monomer to DMAC. Given that the PLLA block can undergo either hydrolytic or enzymatic degradation, such nanoparticles are expected to offer potential applications in various fields, including next-generation sustainable Pickering emulsifiers.

Raman evaluation of the crystallinity degree and composition of poly(L-lactide-co-ε-caprolactone)

In this work, we study two series of the copolymers of L-lactide (LLA) and ε-caprolactone (CL) with the CL molar content of 5, 15, and 30 %. The first series was the commercial semicrystalline granules (Corbion, Netherlands), which we analyzed without any additional modification. The second series was amorphous films, prepared from the granules by hot pressing with the subsequent fast quenching in order to avoid the crystallization. We used Raman spectroscopy in conjunction with the quantum chemical modeling to evaluate the structure of the copolymers. As additional methods, we applied X-ray diffraction (XRD) analysis and differential scanning calorimetry (DSC). The main result of our study is the elaboration of the Raman methods of quantitative analysis of the relative contents of the comonomers and the crystallinity degree of the poly(L-lactide-co-ε-caprolactone). These methods are based on measurements of the ratios of the peak intensities of the poly(L-lactide) (PLLA) bands at 411 and 874 cm−1, the PLLA band at 2947 cm−1 and the poly(ε-caprolactone) band at 2914 cm−1. Raman study shows that growth of the CL content causes the monotonous decrease in the crystallinity degree of PLLA blocks. Density functional theory analysis of LLA decamer in the conformation of helix 103 allows us to assign the PLLA Raman bands. The Raman data on the composition and crystallinity degree of the copolymers correlate very well with the results of XRD and DSC studies, as well as with the information on the composition of the copolymers provided by manufacturer.

High Performance Star Block Aliphatic Polyester Thermoplastic Elastomers Using PDLA-b-PLLA Stereoblock Hard Domains.

Star block (ABC)4 terpolymers consisting of a rubbery poly(γ-methyl-ε-caprolactone) (PγMCL) (C) core and hard poly(l-lactide) (PLLA) (B) and poly(d-lactide) (PDLA) (A) end-blocks with varying PDLA to PLLA block ratios were explored as high-performance, sustainable, aliphatic polyester thermoplastic elastomers (APTPEs). The stereocomplexation of the PDLA/PLLA blocks within the hard domains provided the APTPEs with enhanced thermal stability and an increased resistance to permanent deformation compared to nonstereocomplex analogs. Variations in the PDLA:PLLA block ratio yielded tunable mechanical properties likely due to differences in the extent and location of stereocomplex crystallite formation as a result of architectural constraints. This work highlights the improvements in mechanical performance due to stereocomplexation within the hard domains of these APTPEs and the tunable nature of the hard domains to significantly impact material properties, furthering the development of sustainable materials that are competitive with current industry standard materials.

Reversible Dehydration-Hydration of Poly(ethylene glycol) in Langmuir Monolayers of a Diblock Copolymer Inferred from Changes in Filament Curvature.

We investigated changes in the hydration state of poly(ethylene glycol) (PEG) through morphological changes in Langmuir monolayers of a PEG-poly(l-lactide) (PlLA) (PEG-b-PlLA) diblock copolymer. When the PEG blocks were hydrated, we observed a remarkable morphology of bundles of ring-like filaments, arranged concentrically, yielding densely packed disk-like objects with a hollow center. We attribute the uniform curvature of these filaments to a strong mismatch between the molecular volumes occupied by PlLA blocks and hydrated PEG blocks. Under the constraint that each hydrated PEG block is attached to a hydrophobic PlLA block anchored to the air-water interface, this mismatch of molecular volumes caused strong repulsion within the PEG layer, in particular when the PlLA blocks packed tightly. Induced by a transition in the ordering of the PlLA blocks, the PEG blocks lost their hydration shell and packed into a dense polymer brush, accompanied by a reduction of the pressure within the PEG layer. During this packing process, the curvature of the filaments was eliminated and the ring-like filaments fractured into small linear pieces. Upon compression, the linear pieces coalesced and formed long filaments aligned in parallel. Importantly, upon expansion of the Langmuir film, these changes in morphology were reversible, and the PEG blocks could be rehydrated and bundles of concentrically arranged ring-like filaments were reformed. We conclude that the change in curvature of the filaments provides a means for distinguishing between the hydrated and dehydrated states of PEG.

Iron(ii) carboxylates and simple carboxamides: an inexpensive and modular catalyst system for the synthesis of PLLA and PLLA-PCL block copolymers.

The combination of inexpensive Fe(ii) acetate with low molecular weight aliphatic carboxamides in situ generates an effective catalyst system for the ring opening polymerisation of lactones. PLLAs were produced in melt conditions with molar masses of up to 15 kg mol-1, narrow dispersity (Đ = 1.03), and without racemisation. The catalytic system was investigated in detail with regard to Fe(ii) source, and steric and electronic effects of the amide's substituents. Furthermore, the synthesis of PLLA-PCL block copolymers of very low randomness was achieved. This commercially available, inexpensive, modular, and user-friendly catalyst mixture may be suitable for polymers with biomedical applications.

Role of the Branched PEG-b-PLLA Block Chain in Stereocomplex Crystallization and Crystallization Kinetics for PDLA/MPEG-b-PLLA-g-glucose Blends with Different Architectures.

The isothermal crystallization behavior and corresponding morphology evolution of poly(d-lactic acid) (PDLA) blends with PLLA6.7k or MPEG-b-PLLA6.7k-g-glucose with different architectures and different PLLA-grafted copolymer contents were investigated. The formation of stereocomplexes (SCs) in between the chain branched structure of MPEG-b-PLLA6.7k-g-glucose and PDLA chains acting as the physical crosslinking points slows down the motion of PDLA chains, but the SCs could act as a heterogeneous nucleating agent for the late formation of homocrystals (HCs) in the blend system, accelerating the crystallization kinetics of HCs through enhancing the nucleation density. For PDLA/MPEG-b-PLLA6.7k-g-glucose blends, the mobility of SCs in the blend system and the nucleation density of SCs in the blends exhibit oppositional behavior during the isothermal crystallization at a Tc of 130 °C. The evolution of the crystal growth and structure during the isothermal crystallization process by rheometry has revealed the interesting role of the branched chains of MPEG-b-PLLA6.7k-g-glucose in the mechanism of the crystallization in PDLA blends.

Polymorphic Crystallization Behavior of a Poly(butylene adipate) Midblock within a Poly(L-lactide-butylene adipate-L-lactide) Triblock Copolymer.

New biodegradable aliphatic PLLA-PBA-PLLA copolymers with soft poly(butylene adipate) (PBA) and hard poly(l-lactide) (PLLA) building blocks were synthesized via ring-opening polymerization (ROP). Proton nuclear magnetic resonance (1HNMR) was utilized to confirm the volume fraction of PBA (fPBA) within PLLA-PBA-PLLA. It was found that a PBA midblock (PBA-mid) within PLLA-PBA-PLLA-s (PLLA-PBA-PLLA triblock copolymer with a short PLLA block length) might display lamellar domain structure. However, PBA-mid within PLLA-PBA-PLLA-l (PLLA-PBA-PLLA triblock copolymer with a long PLLA block length) might locate itself as a nanoscale cylindrical domain surrounded by a PLLA continuous phase. Polymorphic crystals of PBA-mid within the PLLA-PBA-PLLA copolymers were formed after melt crystallization at the given temperatures, which were studied by differential scanning calorimetry (DSC) and wide-angle X-ray diffraction (WAXD) analysis. According to the WAXD and DSC analyses, it was interesting to find that the α-type crystal of PBA-mid was favorable to develop in the lower temperature region regardless of the state (crystallization or amorphous) of the PLLA component. Additionally, when the PLLA component was held in its amorphous state, it was easier for PBA-mid within the PLLA-PBA-PLLA copolymers to transform from the metastable β-form crystal to the stable α-form crystal. Furthermore, polarized optical microscopy (POM) photos provided direct evidence of the polymorphic crystals of PBA-mid within PLLA-PBA-PLLAs.

Crystallization, morphology and mechanical property enhancement of block copolymer-based metallosupramolecular polymers by incorporating metal coordinating ligand into poly(L-lactic acid) block

We propose a new strategy to prepare robust films with unusual mechanical properties for low molecular weight block copolymers-based materials by utilizing metal−ligand (M−L) coordination to create physical crosslinking into the hard block. Using an amine-terminated triazole as an initiator, a poly(L-lactic acid) (PLLA) containing a triazole group was prepared by ring opening polymerization. The hydroxy group of this polymer was subsequently reacted with isocyanate-poly(butadiene) (PB), resulting for the first time in PLLA/PB block copolymers bearing metal-coordinating ligands on PLLA chain. The subsequent addition of Co2+, Fe3+, or Cu2+ metal ions resulted in formation of metallosupramolecular polymers (MSP) through M−L bonds, as could be shown by viscosimetry and UV–vis spectra. The influence of blend of different types of metal, L/M ratio, the chain length of PLLA blocks (1.6 or 3.0 kg/mol) of block copolymers on the properties has been investigated in detail. Compared to the mechanical properties of uncoordinated block copolymer, MSP showed significantly larger Young's modulus, higher elongation at break, and larger break strength. For uncoordinated oligomer with a toughness of 0.82 J/m3, the toughness increased by 101- and 348-fold with the incorporation of Co2+ and Cu2+, respectively. Because of the particularly weak bond strength associated with the Fe3+−triazole bond, MSP containing Fe3+ had lower Young's modulus, break strength than MSPs containing Co2+ and Cu2+. Incorporation of 50% Cu2+ and 50% Co2+ into block copolymers was found to be beneficial to prepare MSPs with high extensibility and large Young's modulus simultaneously. For all MSPs, M−L complex and polymer matrix were found to microphase separate into nano-domains. Crystallization rate of PLLA in MSP featuring Co2+ metal ion was lower than that of Cu2+ and Fe3+, demonstrating that chain mobility relied on both the dynamic character and bond strength.

Curving and Twisting in Self-Assembly of Triblock Terpolymers Driven by a Chiral End Block

A series of triblock terpolymers composed of a chiral end block, poly(l-lactide) (PLLA) (designated as chiral triblock terpolymers), are designed and synthesized for self-assembly. The chiral PLLA block can contribute the chirality effect for the twisting of microphase-separated domains. By attaching an asymmetric amount of the chiral block to a symmetric diblock of polyisoprene-b-polystyrene (PI-PS), compositional asymmetry can be created for the curving of microphase-separated domains. Moreover, the difference in persistence lengths of PS and PLLA blocks can give conformational asymmetry to the curving. With the combined effects of twisting and curving, the curvature at the saddle surface of microphase-separated domains might become significant to give the formation of a network phase. Consequently, a transformation from two-domain lamellae to core–shell network phases, then to a core–shell cylinder phase, and finally to a three-domain lamellar phase with undulation due to the rod–rod interaction with the chirality effect from the semiflexible PLLA, can be found in the isopleths of the triblocks. Interestingly, a core–shell double diamond phase could be found near the center of the ternary phase diagram; we speculate that the alleviation of packing frustration in the core of the self-assembled microdomain is attributed to the character of semiflexible PLLA. Accordingly, the phase window of network formation can be enlarged by the combined effects of compositional asymmetry, conformational asymmetry, and chirality.

Crystallization, thermal and mechanical properties of stereocomplexed poly(lactide) with flexible PLLA/PCL multiblock copolymer.

In this work, the synthesized PLLA/PCL multi-block copolymers with different compositions were introduced into a stereocomplexed poly(lactide) (sc-PLA) matrix to accelerate the stereocomplexation of PLA enantiomers and improve its inherent brittleness. The PLLA/PCL multi-block copolymers were in different compositions to adjust the molecular weight of the PLLA block. The structure, molecular weight, crystallization behavior, crystal structure and thermal stability of PLLA/PCL multi-block copolymers were investigated. The results indicated that PLLA/PCL multi-block copolymers with controllable structure and composition were successfully synthesized. On this basis, the blends of sc-PLA and PLLA/PCL multi-block copolymers were prepared by solution casting, and characterized. The results revealed that the introduction of PLLA/PCL multi-block copolymers promoted the stereocomplexation of the PLA enantiomers during the melting crystallization process to obtain a complete stereocomplexed material. But the presence of the PCL block leads to a decrease in the melting temperature of the stereocomplex and difficulty in homogeneous nucleation. Compared with sc-PLA, the elongation at break of the blends was significantly improved and their tensile strengths were only slightly reduced. And the thermal stability and mechanical properties of the blends could be adjusted by controlling the content and composition of PCL/PLLA multi-block copolymers. These results revealed that the degree of stereocomplexation and toughness of sc-PLA were improved, which may expand the application fields of PLA-based materials.

Morphology and Degradation of Multicompartment Microparticles Based on Semi-Crystalline Polystyrene-block-Polybutadiene-block-Poly(L-lactide) Triblock Terpolymers.

The confinement assembly of block copolymers shows great potential regarding the formation of functional microparticles with compartmentalized structure. Although a large variety of block chemistries have already been used, less is known about microdomain degradation, which could lead to mesoporous microparticles with particularly complex morphologies for ABC triblock terpolymers. Here, we report on the formation of triblock terpolymer-based, multicompartment microparticles (MMs) and the selective degradation of domains into mesoporous microparticles. A series of polystyrene-block-polybutadiene-block-poly(L-lactide) (PS-b-PB-b-PLLA, SBL) triblock terpolymers was synthesized by a combination of anionic vinyl and ring-opening polymerization, which were transformed into microparticles through evaporation-induced confinement assembly. Despite different block compositions and the presence of a crystallizable PLLA block, we mainly identified hexagonally packed cylinders with a PLLA core and PB shell embedded in a PS matrix. Emulsions were prepared with Shirasu Porous Glass (SPG) membranes leading to a narrow size distribution of the microparticles and control of the average particle diameter, d ≈ 0.4 µm–1.8 µm. The core–shell cylinders lie parallel to the surface for particle diameters d < 0.5 µm and progressively more perpendicular for larger particles d > 0.8 µm as verified with scanning and transmission electron microscopy and particle cross-sections. Finally, the selective degradation of the PLLA cylinders under basic conditions resulted in mesoporous microparticles with a pronounced surface roughness.

Sequential Crystallization and Multicrystalline Morphology in PE-b-PEO-b-PCL-b-PLLA Tetrablock Quarterpolymers.

We investigate for the first time the morphology and crystallization of two novel tetrablock quarterpolymers of polyethylene (PE), poly(ethylene oxide) (PEO), poly(ε-caprolactone) (PCL), and poly(l-lactide) (PLLA) with four potentially crystallizable blocks: PE187.1-b-PEO3715.1-b-PCL2610.4-b-PLLA197.6 (Q1) and PE299.5-b-PEO268.8-b-PCL237.6-b-PLLA227.3 (Q2) (superscripts give number average molecular weights in kg/mol, and subscripts give the composition in wt %). Their synthesis was performed by a combination of polyhomologation (C1 polymerization) and ring-opening polymerization techniques using a ″catalyst-switch″ strategy, either ″organocatalyst/metal catalyst switch″ (Q1 sample, 96% isotactic tetrads) or ″organocatalyst/organocatalyst switch″ (Q2 sample, 84% isotactic tetrads). Their corresponding precursors—triblock terpolymers PE-b-PEO-b-PCL, diblock copolymers PE-b-PEO, and PE homopolymers—were also studied. Cooling and heating rates from the melt at 20 °C/min were employed for most experiments: differential scanning calorimetry (DSC), polarized light optical microscopy (PLOM), in situ small-angle X-ray scattering/wide-angle X-ray scattering (SAXS/WAXS), and atomic force microscopy (AFM). The direct comparison of the results obtained with these different techniques allows the precise identification of the crystallization sequence of the blocks upon cooling from the melt. SAXS indicated that Q1 is melt miscible, while Q2 is weakly segregated in the melt but breaks out during crystallization. According to WAXS and DSC results, the blocks follow a sequence as they crystallize: PLLA first, then PE, then PCL, and finally PEO in the case of the Q1 quarterpolymer; in Q2, the PLLA block is not able to crystallize due to its low isotacticity. Although the temperatures at which the PEO and PCL blocks and the PE and PLLA blocks crystallize overlap, the analysis of the intensity changes measured by WAXS and PLOM experiments allows identifying each of the crystallization processes. The quarterpolymer Q1 remarkably self-assembles during crystallization into tetracrystalline banded spherulites, where four types of different lamellae coexist. Nanostructural features arising upon sequential crystallization are found to have a relevant impact on the mechanical properties. Nanoindentation measurements show that storage modulus and hardness of the Q1 quarterpolymer significantly deviate from those of the stiff PE and PLLA blocks, approaching typical values of compliant PEO and PCL. Results are mainly attributed to the low crystallinity of the PE and PLLA blocks. Moreover, the Q2 copolymer exhibits inferior mechanical properties than Q1, and this can be related to the PE block within Q1 that has thinner crystal lamellae according to its much lower melting point.

Non-Isothermal Crystallization Kinetics of Poly(Ethylene Glycol)-Poly(l-Lactide) Diblock Copolymer and Poly(Ethylene Glycol) Homopolymer via Fast-Scan Chip-Calorimeter.

The non-isothermal crystallization kinetics of double-crystallizable poly(ethylene glycol)–poly(l-lactide) diblock copolymer (PEG-PLLA) and poly(ethylene glycol) homopolymer (PEG) were studied using the fast cooling rate provided by a Fast-Scan Chip-Calorimeter (FSC). The experimental data were analyzed by the Ozawa method and the Kissinger equation. Additionally, the total crystallization rate was represented by crystallization half time t1/2. The Ozawa method is a perfect success because secondary crystallization is inhibited by using fast cooling rate. The first crystallized PLLA block provides nucleation sites for the crystallization of PEG block and thus promotes the crystallization of the PEG block, which can be regarded as heterogeneous nucleation to a certain extent, while the method of the PEG block and PLLA block crystallized together corresponds to a one-dimensional growth, which reflects that there is a certain separation between the crystallization regions of the PLLA block and PEG block. Although crystallization of the PLLA block provides heterogeneous nucleation conditions for PEG block to a certain extent, it does not shorten the time of the whole crystallization process because of the complexity of the whole crystallization process including nucleation and growth.

Solution-grown composite single crystals of poly(L-lactic acid)-b-polystyrene block copolymers and poly(L-lactic acid) homopolymers

In the present work, composite single crystals (CSCs) composed of poly (L-lactic acid) (PLLA) homopolymer and poly (L-lactic acid)-b-polystyrene (PLLA-b-PS) block copolymers (BCPs) were prepared by solution co-crystallization. The effects of crystallization temperature (Tc), mass ratio of BCP/homopolymer and PS block length on the morphology and growth habit of the CSCs were investigated. Particularly, parallelogram CSCs with four {110} crystal planes as edges tend to be formed at a low Tc and a small BCP/homopolymer mass ratio for the BCP with a short PS block. The parallelogram shape of the crystals indicates the growth rates along four {110} crystal planes are different in two directions. It is proposed that the folded surface free energy is reduced after incorporation of PLLA-b-PS BCP into the crystals, leading to accelerated growth and concave surface structure along the long side direction. The chain folding of the PLLA block in the CSCs was also discussed. It is found that, in order to match the chain folding of PLLA homopolymer, the PLLA block in the BCPs adopts more chain folds in the CSCs than that in the single crystals formed by neat BCPs.

Direct identification of three crystalline phases in PEO-b-PCL-b-PLLA triblock terpolymer by In situ hot-stage atomic force microscopy

In this work, we provide a detailed description of the tri-lamellar nanoscale morphology of a triple crystalline PEO-b-PCL-b-PLLA triblock terpolymer obtained by Hot-Stage Atomic Force microscopy (AFM) imaging and Wide Angle X-ray scattering (WAXS) analysis for the first time. The precursor PCL-b-PLLA diblock copolymer has also been included in the study for comparison purposes. A two-step crystallization protocol has been applied to create a distinct lamellar morphology. Both WAXS and AFM revealed the double crystalline nature of the diblock copolymer. However, the identification of multiple crystalline phases in the triblock terpolymer by AFM and WAXS at room temperature is not straightforward. The advantages of hot-stage AFM allowed following the evolution of the lamellar morphology and the successive melting of the tricrystalline PEO-b-PCL-b-PLLA sample during heating. Taking into account the melting temperature of each crystalline block, the existing lamellar populations were clearly identified. At 45 °C, the thinnest lamellae disappeared, due to the melting of PEO crystals. The medium size lamellae disappeared at 60 °C when PCL crystals melt. At that temperature, the only remaining crystals are those of the PLLA block. AFM mechanical modulus images and the analysis of the cross-sectional heights provide further evidence of the lamellar self-assembly of the triblock terpolymer. It was found that two lamellar arrangements are possible at room temperature; either a perfect interdigitation where PCL and PEO lamellae are sandwhiched between PLLA lamellae (i.e., PLLA/PEO/PCL/PLLA), or only one PEO or PCL lamella in between two PLLA lamellar crystals distributed randomly (i.e., PLLA/PEO/PLLA or PLLA/PCL/PLLA). Hot-Stage AFM is a valuable technique to elucidate the complex morphological features of multi-crystalline systems.

Toward all stereocomplex-type polylactide with outstanding melt stability and crystallizability via solid-state transesterification between enantiomeric poly(l-lactide) and poly(d-lactide)

Stereoblock copolymerization is regarded an appealing strategy to substantially enhance the melt stability (i.e., the survival ability of the intermolecular collaboration between poly(l-lactide) (PLLA) and poly(d-lactide) (PDLA) upon melting) of high-molecular-weight (high-MW) stereocomplex-type polylactide (SC-PLA), however it usually suffers from complicated synthetic procedures and even impaired sustainability. Herein, solid-state transesterification (SST) has been devised as a facile and robust route to prepare unique multi-stereoblock PLA copolymers with outstanding melt stability and unexpectedly strong crystallizability from commercial available linear high-MW PLLA/PDLA (50/50) blends. The SST was performed through low-temperature (i.e., 180 °C) melt-blending of PLLA and PDLA in the presence of trace amounts (0.03–0.035 wt%) of catalysts, where the enantiomeric PLA chains could rapidly co-crystallize into solid-state SC crystallites upon melting and subsequently the hetero-chain transesterification reaction occurs exclusively in the mobile amorphous phase of the pre-formed SC crystallites. As a result, multiblock-like PLLA-b-PDLLA-b-PDLA copolymers with long crystallizable PLLA and PDLA blocks are in-situ generated. The results show that high-content SC crystallites can be exclusively formed in the melt-crystallization of the copolymers even at high cooling rates (e.g., 40 °C/min) and low temperatures (e.g., 140 °C). More interestingly, the presence of the non-crystallizable PDLLA blocks not only does not disturb the SC crystallizability of the enantiomeric PLA blocks, as evidenced by the same high crystallinity and melting temperature as those of starting PLLA/PDLA blends, but also increase the crystallization rate by stabilizing the clusters of ordered PLLA/PDLA segments in the copolymer melt. Overall, these findings could open a new pathway to develop melt-processible all SC-PLA for engineering applications.

ABA triblock copolyesters composed of poly(l-lactide) A hard blocks: comparison of amorphous and crystalline unsaturated aliphatic polyesters as B soft blocks

The property profiles of ABA triblock copolymers can be precisely customized by changing the chemical structure of the components. The identification of the midblock is the key point in the development of PLLA-containing ABA triblock copolymers. Two kinds of unsaturated aliphatic polyesters, crystalline poly(cis-butene succinate) (PcBS) and amorphous poly(cis-butene glutarate) (PcBG) with dihydroxyl end groups were prepared by polycondensation reactions. Then, dihydroxyl-terminated PcBS and PcBG were used as macroinitiators to initiate ring opening of polymerization of L-lactide toward two series of fully biobased biodegradable PLLA-b-PcBS-b-PLLA and PLLA-b-PcBG-b-PLLA triblock copolymers with PLLA as hard end-blocks. The influences of the midblocks and the endblocks length on microstructure, thermal and tensile properties of the triblock copolymers were studied. Compared to homopolymer PLLA, all the triblock copolymers had a much higher elongation at break with lower tensile strength and tensile modulus, depending on the length of PLLA blocks. It was found that the amorphous PcBG midblock plays a greater role than the crystalline PcBS midblock in enhancing the tensile toughness of ABA triblock copolymers. PLLA-b-PcBG-b-PLLA composed of shorter PLLA hard block displayed typical elastomeric behavior without yield, which is a promising aliphatic polyester-based thermoplastic elastomer. The unsaturated carbon–carbon double bonds in these polyesters backbone provide a variety of opportunities for further modifications.

Well-defined high molecular weight polyglycolide-b-poly(L-)lactide-b-polyglycolide triblock copolymers: synthesis, characterization and microstructural analysis

Block copolymerization is already a proven technique to manipulate the properties of polymeric materials. Herein, our work presents a facile synthesis of high molecular weight polyglycolide-b-poly(L-)lactide-b-polyglycolide (b-PLLGA) triblock copolymers by ring-opening polymerization (ROP) in bulk at considerably low temperature. A series of ABA-type triblock copolymers was successfully prepared and microstructural properties were thoroughly investigated against random copolymers of poly(L-lactide-co-glycolide) (r-PLLGA). This synthesis method led to the preparation of high molecular weight b-PLLGAs with highly defined chain microstructure and an intrinsic viscosity [η] was obtained as high as 1.62 dl/g when [M]:[I] was [1]:[1000]. The investigations revealed that the prepared copolymers are in block type chain microstructure, having exclusive thermal transitions and sequence/segment properties. DSC analysis revealed that two glass (Tg) transitions and two melt transitions (Tm) exclusively associated to PGA block and PLLA block. Results were further confirmed by homosequenses of –LLLL- and -GGGG- from 13C-NMR spectroscopy. Tensile results revealed that b-PLLGA have higher tensile strength and Young’s modulus as compared to r-PLLGA. Moreover, b-PLLGAs are more thermally stable and have a wider thermal processing window.