Plastic Sheet Research Articles

Determination of kilovoltage x-ray therapy depth doses with open-ended applicators.

The purpose of this work was to determine percentage depth dose (PDD) curves for kilovoltage x-rays from the WOmed-T105 unit, with open-ended steel applicators and beam qualities ranging from 0.5 to 4.2mm Al. Measurements were made with parallel plate chambers in a water phantom, with extrapolation based on a fifth order polynomial used to estimate the surface dose. Measurements were also made with parallel plate chambers in a plastic water phantom, with thin plastic sheets used to obtain detailed measurements at shallow depths (less than 1mm). Monte Carlo simulations were performed using the EGSnrc package, with two different sources as input: a SpekPy simulation of the x-ray beam and a full simulation of the x-ray tube, treatment head and applicators. Results showed that all four methods (two measurements and two simulations) agreed within the measurement uncertainty at depths greater than 2mm. At shallow depths, significant differences were noted. At depths less than 0.1mm, the full Monte Carlo simulation and the solid water measurements showed a sharp spike in surface dose which is attributed to electron contamination, which was not seen in the SpekPy Monte Carlo simulation or the extrapolated water measurements. At depths between 0.1mm and 2mm, beyond the range of contaminant electrons, the extrapolated water measurements underestimate the dose by up to 13% compared to the full Monte Carlo simulation and the solid water measurements, attributed to fluorescent photons generated in the applicators. This work demonstrates that for open-ended applicators, measurement of depth doses in water with extrapolation of surface dose has the potential to significantly underestimate the dose at shallow depths between the surface and 2mm, even after eliminating electron contamination from the beam.

MONITORING KUALITAS LINGKUNGAN DALAM UPAYA IMPLEMENTASI PENGELOLAAN DAN PEMANTAUAN LINGKUNGAN DI PT XYZ

The global decline in environmental quality includes direct and indirect impacts from industries that meet individual needs or complementary facilities. Industrial development is one of the support systems that plays a role in meeting these needs. One of the industries located in the bonded area in the Cikarang area produces sheet plastic goods industry in the form of Polycarbonate roofing. Related to this, PT XYZ (the initiator) in the implementation of its daily operations makes efforts to manage and monitor the quality of the environment so that it can be controlled and managed if it exceeds the permitted capacity or quality standards as regulated in the applicable laws and regulations in accordance with the affected environmental components or humans, in this case workers who are directly related to the production process. The purpose of this study is to provide information on the company's operational conditions during a certain period so that environmental quality can be continuously monitored and corrected if any exceed the predetermined quality standards. The research was conducted at PT XYZ which is located in the Industrial Estate, Cicau Village, Central Cikarang District, Bekasi Regency, West Java. The object of research is industrial environmental quality monitoring. The research method is experimental, including environmental quality sampling at several monitoring points that can represent the impacts resulting from industrial activities, laboratory analysis, then the results of the analysis are compared with applicable regulations to be used as a basis for decision making for no further or correction of environmental quality that has the potential to decline and needs improvement. The noise level at PT XYZ for monitoring semester 2, year 2022 where the noise level at 1 (one) monitoring point exceeds the quality standard but is still within the noise level tolerance of ± 3 dBA, namely the Crusher Area, 85.9 dBA respectively. The measured work environment climate in semester 2, year 2022 has increased for the Fisnish Good area and Crusher Area and has not increased significantly so that control efforts are needed, currently the installation of environmentally friendly solar cell panels has been carried out and is awaiting permission to be operationalized

Enhancement imaging of developed latent blood fingerprints using TOF-SIMS

As one of the most common types of evidence in violent cases, blood fingerprints play an important role in identifying suspects. Typically, Latent blood fingerprints from a crime scene require the application of chemical development reagents followed by photographing to visualize the ridge detail. However, conventional development techniques are not effective in the visualization of poor latent blood fingerprints due to the formation conditions. Time-of-flight secondary ion mass spectrometry (TOF-SIMS) is a surface analysis technique that combines high mass resolution and high spatial resolution to recover through mass spectrometry imaging (MSI) to reveal fingerprints that are invisible to the naked eye, especially conventional visualization methods. In this study, an enhancement method for latent blood fingerprints was established by analyzing blood fingerprints that showed poor visibility using conventional methods (acid yellow, amido black 10B, tetramethylbenzidine) on plastic sheets, aluminum foil, various papers, and other objects. Additionally, blood samples were diluted with distilled water at concentration gradients of 1:5, 1:10, 1:20, and 1:100 to test the method's sensitivity. Latent fingerprints of blood that aged 14, 30, and 54 days were also examined. Results showed that this method not only enhances the development of fingerprints under challenging conditions but also allows for the recovery of incomplete fingerprints and the separation of overlapping fingerprints. Compared to conventional methods, this approach significantly improves the development effect of latent blood fingerprints while maintaining universality, reliability and practicality.

Utilization of graphene as an alternative sustainable amendment in improving soil health through accelerated decomposition of oil palm mulch and enhanced nutrient availability

Graphene has unique properties for improving soil health properties such as nutrient availability, soil physical and chemical properties, and controlled release of essential elements. This research aimed at determining the impact of graphene amendment on the decomposition of oil palm frond mulching and on soil health status. The study was conducted using a factorial experiment in completely randomized design with two main factors: (i) covering conditions: cover with plastic sheet and no cover, and (ii) graphene application that included T1 (control): oil palm frond mulching (OFM), T2: OFM + graphene (G), T3: OFM + G + chemical fertilizer, and T4: OFM + G + goat manure. The results indicated that there were significant differences among graphene applications, between cover conditions, and in interactions between graphene applications and cover conditions for all soil characteristics in the most observed month. In the third month of soil analysis, the treatment of graphene applications showed higher electrical conductivity (T2: 151.7 ± 6.8 µS cm−1), available phosphorus (T3: 9.0 ± 6.7 mg kg−1), exchangeable potassium (T2: 67.1 ± 24.9 mg kg−1), and exchangeable calcium (T3: 95.4 ± 5.1 mg kg−1), compared to control. The cover condition showed suitable soil pH (5.0 ± 0.2), higher soil available phosphorus (7.1 ± 5.0 mg kg−1), and exchangeable calcium (599.1 ± 235.2 mg kg−1), but the no-cover condition presented higher soil organic matter (0.7% ± 0.2%), exchangeable potassium (60.3 ± 19.1 mg kg−1), and exchangeable magnesium (96.7 ± 11.4 mg kg−1). Correlation results indicated that most soil characteristics were correlated under graphene applications. Principal component analysis showed that the treatments of graphene application dominated most soil characteristics. The results suggest that graphene has potential for improving soil health properties and can be applied as an alternative sustainable amendment to accelerate the decomposition of oil palm frond mulch and enhance nutrient availability for oil palm. In addition, the authors suggest that further investigations should consider more soil health parameters in long-term field studies for a better understanding and to provide recommendations to farmers.

Soil microorganisms play an important role in the detrimental impact of biodegradable microplastics on plants

Biodegradable plastics were developed to mitigate environmental pollution caused by conventional plastics. Research indicates that biodegradable microplastics still have effects on plants and microorganisms as their non-biodegradable counterparts, yet the effects on vegetable crops are not well-documented. Additionally, the function of soil microorganisms affected by biodegradable microplastics on the fate of microplastics remains unverified. In this study, Brassica chinensis was cultivated in soil previously incubated for one year with low-density polyethylene (LDPE-MPs) and poly (butylene adipate-co-terephthalate) microplastics (PBAT-MPs) at 0.05 % and 2 % concentrations. High concentrations of PBAT-MPs significantly reduced the biomass to 5.83 % of the control. The abundance of Methyloversatilis, IS-44, and UTCFX1 in the rhizosphere bacterial community increased significantly in the presence of PBAT-MPs. Moreover, these microplastics significantly enhanced soil enzyme activity. Incubation tests were performed with three PBAT plastic sheets to assess the function of the altered bacterial community in the soil of control (Control-soil) and soil treated with high concentrations of PBAT-MPs (PBAT-MPs-soil). Scanning Electron Microscopy and Atomic Transfer Microscopy (SEM/ATM) results confirmed enhanced PBAT degradation in the PBAT-MPs-soil. PICRUST2 analysis revealed that pathways related to substance degradation were upregulated in the PBAT-MPs-soil. Furthermore, a higher percentage of strains with PBAT-MPs-degrading ability was found in PBAT-MPs-soil. Our results confirm that PBAT-MPs significantly inhibit the growth of vegetable crops and that soil bacterial communities affected by PBAT-MPs are instrumental in degrading them.

Study on electric pulse effect on steel DP780 during roll forming

The electrophysical impact on metals introduces a novel optimization avenue for roll forming. This study explores the influence of different electric pulse parameters (peak current and frequency) on the roll forming behavior of DP780 high-strength steel. Through electric pulse-assisted tensile, bending, and roll forming experiments, coupled with microstructure and fracture morphology analyses, the study comprehensively assesses the impact of electric pulses on the mechanical properties and springback mechanism of DP780 sheets. Results indicate that electric pulses reduce deformation resistance and enhance the plasticity of DP780 sheets by repairing defects, promoting dislocation slip, and changing the fracture form of the material. Moreover, electric pulses effectively inhibit springback in roll forming, particularly at larger bending angles and under specific E-pulsing parameters. This is attributed to the promotion of residual stress release by electric pulses, leading to a reduction in springback. In conclusion, electric pulse assistance optimizes the roll forming process of DP780 high-strength steel, evidenced by decreased deformation resistance, improved material plasticity, and effective suppression of springback. These findings open up a new optimization pathway for sheet metal forming.

Numerical analysis of velocity slip and magnetic Soret effect on dissipative Maxwell liquid motion about a stretching wall with heat source/sink

The main aim of present numerical analysis is to explore the effects of viscous dissipation and velocity slip on the two-dimensional steady-state viscous incompressible flow of Maxwell fluid over a stretching sheet under the infleunce of magnetic field. Novel collective effects of heat source/sink and Soret impacts have been included in the governing equations to explore the salient features of heat and mass transport mechanism. Further, the velocity slip is introduced into the boundary conditions to depict the momentum transport behavior in the flow region. A typical Maxwell fluid model is deployed to separate the non-Newtonian flow behavior from that of classical Newtonian fluids. However, the visco-elastic Maxwell fluid finds its abundant applications in various fields of engineering and medicine such as plastic sheet drawing, metallurgy, polymer sheet extrusion, chemical engineering, electronic cooling, injection molding and nuclear cooling and many others. Inspired by these applications, authors have made an attempt to disclose the magneto-thermo salient features of slip flow of Maxwell fluid over stretching wall under Soret effect. The current physical situation results the highly nonlinear coupled two-dimensional steady-state partial differential equations and which are not amenable to any of the direct techniques. Due to this, the suitable similarity transformations are deployed to reduce the dimensional complexity of the constructed partial differential equations. A robust Matlab-based bvp4c scheme is utilized as a basic tool to produce the similarity solutions of the governing equations. The computer generated numerical data is presented in view of flow, temperature and concentration profiles including physical quantities of interest like skin-friction coefficient, heat and mass transport rates for the various values of physical parameters range such as, 0 ≤ M ≤ 1 , 0 ≤ β ≤ 1 , − 0.3 ≤ λ ≤ 0.6 , − 0.2 ≤ Q ≤ 0.2 , 0 ≤ Ec ≤ 2.2 , 1.2 ≤ Pr ≤ 2.2 , 0 ≤ Sr ≤ 0.5 and 1.2 ≤ Sc ≤ 2.2 . Accordingly, it is noticed that, enhancing magnetic parameter decreases the Maxwell fluid flow and amplifies the temperature and concentration fields. Enlarging Maxwell fluid parameter decreases the velocity field and increases the temperature and concentration profiles. Amplified slip parameter diminished the Maxwell flow inside the flow regime. Increasing heat source/sink parameter amplifies the temperature field. Further, magnifying Soret number amplifies the concentration field. Magnitude of skin-friction coeffiecient enlarged with amplified magnetic and Maxwell fluid parameters. Heat and mass transport rates decayed with enhancement in heat source/sink and Soret parameters. Finally, it is described that, the present similarity solutions showing good agreement with the previously reported solutions in the literature and this fact confirms the accurateness of the used numerical method and the generated similarity solutions.

Enhanced Scenedesmus obliquus Cultivation in Plastic-Type Flat Panel Photobioreactor for Biodiesel Production

A plastic-type flat panel photobioreactor (PTFPP) prototype was designed for microalgae cultivation as biodiesel feedstock. The growth, biomass, and lipid production of the oleaginous microalga Scenedesmus obliquus were optimized through the enhanced design and cultivation conditions in the PTFPP. The optimization conditions include cultivation of the microalga in a flat panel photobioreactor manufactured from a 10 µm-thick plastic sheet with dimensions of 40 cm in width and 60 cm in height. The width of the designed plastic bags was adjusted by “4 ports” of circular adhesion points which make the volumetric cultural capacity 5 L. Cultivation of the microalga was optimized through the replacement of the sodium nitrate of the BBM medium with urea as a nitrogen source. Cultivation bags were subjected to continuous illumination with 3000 lux white, fluorescent lamps and aerated with 1.5 L air/min (equal to 0.3 VVM). Biomass production from the designed PTFPP reached 3 g/L with around 40% lipid content (on a dry weight basis). Based on a GC-MS analysis of the produced fatty acid methyl ester (biodiesel) from S. obliquus, the percentage of C16 and C18 fatty acids reached more than 90% of the defined fatty acids. Out of this percentage, 66.6% were unsaturated fatty acids. The produced fatty acid profile of the S. obliquus biomass cultivated in the designed PTFPP prototype could be considered a suitable feedstock for biodiesel production.

First Report of Gray Mold Caused by Botrytis cinerea on Dragon Fruit (Hylocereus undatus) in Mexico.

The dragon fruit is native of Mexico, and Puebla is the third-largest producing state (SIAP 2023). In June 2023, field sampling was conducted in El Paraíso, Atlixco (18° 49' 5.275" N, 98° 26' 52.353" W), Puebla, Mexico. The mean temperature and relative humidity were 20 °C and 75% for seven consecutive days. Dragon fruits cv. 'Delight' close to harvest with gray mold symptoms were found in a commercial area of 2 ha, with an incidence of 35 to 40% and an estimated severity of 75% on infected fruit. The symptoms included necrosis at the apex, which later spread throughout the fruit, along with a soft, black rot covered in abundant mycelium and sporulation. The fungus was isolated from 40 symptomatic fruits by disinfesting pieces of necrotic tissue with 3% NaClO for one minute, rinsing with sterile distilled water (SDW), plating on Petri dishes with potato dextrose agar, and incubating at 25 °C in the dark. One isolate was obtained from each diseased fruit by the hyphal-tip method. The colonies were initially white with a growth rate of 1.15-1.32 cm per day and turned gray after 10 days; the mycelium was dense and aerial. Spherical and irregular sclerotia were formed, measuring 0.9-1.4 × 0.6-1.1 mm (n = 100). Each Petri dish produced 56-278 sclerotia (n = 40) after 11 days; these were initially white and gradually turned dark brown. Brown to olive conidiophores were straight, septate, and branched, measuring 1075-1520 × 10-21 μm, with elliptical hyaline to light brown conidia of 6.6-11.5 × 5-8.1 μm (n=100). The isolates were tentatively identified as Botrytis cinerea based on morphological characteristics (Ellis 1971). Two representative isolates were chosen for molecular identification and genomic DNA was extracted by the CTAB protocol. The ITS region and the heat shock protein (HSP60), RNA polymerase binding II (RPB2) and glyceraldehyde 3-phosphate dehydrogenase (G3PDH) genes were sequenced (White et al. 1990; Staats et al. 2005). The sequences of a representative isolate (BcPh5) were deposited in GenBank (ITS-OR582337; HSP60-OR636622; RPB2-OR636623; and G3PDH-OR636621). BLAST analysis of the partial sequences of ITS (479 bp), HSP60 (1006 bp), RPB2 (1126 bp), and G3PDH (907 bp) showed 100% similarity to B. cinerea isolates (GenBank: KM840848, MH796663, MK919495, MF480679). Phylogenetic analysis confirmed that BcPh5 clustered with B. cinerea strains. Pathogenicity was confirmed by inoculating the non-wounded surface of 20 detached dragon fruits cv. 'Delight' using the BcPh5 isolate by depositing 20 μl of a 105 conidia/ml suspension with a sterile syringe. The fruits were placed on the rim of a plastic container and inserted in a moisture box with 2 cm of water at the bottom. The box was covered with a plastic sheet to maintain humidity. Control fruits were inoculated with SDW. The inoculated fruits became covered with abundant white to gray mycelium, and soft rot developed within eight days, while no symptoms were observed on the controls. The fungus was re-isolated from the inoculated fruits as described above, fulfilling Koch's postulates. The pathogenicity tests were repeated three times. Gray mold caused by B. cinerea was also recently reported in Mexico on pomegranate (Hernández et al. 2023) and rose apple (Isodoro et al. 2023). As far as we know, this is the first report of B. cinerea causing gray mold on dragon fruit in Mexico. This research is essential for designing integrated management strategies against gray mold on dragon fruits.

Salicylic Acid Alleviates the Adverse of Salinity Stress in Fenugreek (Trigonella foenum-graecum)

Aims: To discover the resistance of the Yemeni genotype of fenugreek to salt stress and the impact of salicylic acid on alleviating salt stress. Study Design: The experimental design adopted a completely randomized block design (RCBD), with pots filled with a 1:2 mixture of sand and soil serving as the experimental units. Place and Duration of Study: in a mini greenhouse covered with white polyethylene plastic sheet at Taiz University during the spring season 2021. The average temperature ranged from 32 ℃ during the day to 29 ℃ at night. chemical analyses were performed at the pharmaceutical laboratory in Al-Saeed University. Methodology: The fenugreek genotype was subjected to varying salinity levels (0, 50, 100, 150, and 200 mM) and the impact of salicylic acid (at concentrations of 0, 0.1, and 0.5 mg/l) in alleviating salt stress effects was examined at two time points: 15 and 30 days after 2 weeks of germination. Results: Increasing salinity significantly reduced shoot and root length and exhibited slight fluctuations influenced by salinity levels above 100 mM. Salicylic acid (SA) significantly reduced shoot length but had no effect on root length. Salinity had no appreciable effect on shoot dry matter (SDM%), while the application of SA significantly decreased it. Root dry matter percentage (RDM%) showed a notable and sharp increase with salinity. However, no appreciable changes in RDM% were observed in response to the SA application. In response to salinity, the ratio of SDM% to RDM% in treated plants decreased sharply, with the lowest ratio achieved when 0.1 SA was used for treatment. There were no significant modifications observed in the amounts of photosynthetic pigments in fenugreek leaves, including chl a, chl b and total chl. Nevertheless, using high concentration of Nacl led to a signifcantly reduced in the carotenoids and the chl. b. The protein content of fenugreek plants treated with salt was much higher than that of control plants. Also, protein levels increased with SA treatment across all NaCl concentration. Proline levels sharply increased with rising salinity, reaching a peak in approximately 22.28 ug/g DW. Application of 0.1 SA led to the highest proline level in comparison to other treatments, which was the highest level of Nacl in the second measurement time. Proline levels in plants treated with 200 Nacl and 0.1 SA were the highest, averaging roughly recorded 49.95 ug/g DW. APX significantly affected on fenugreek plants, the highest APX content was found in plants treated with 50 mM NaCl, the application of 0.1 SA produced the highest level of APX (0.373nm/g protein/minuet) in fenugreek. Catalase (CA) levels significantly decreased, but SA application did not affect CA levels. The data obtained may help in determining fenugreek cultivation areas and in managing breeding programs.

Attitude and performance in controlling dust particles from dental prosthesis and appliance adjustment: a survey of dentists and dental assistants

ObjectivesTo assess the attitude and practices of dentists and dental assistants in managing dust particles generated during dental prostheses or appliances grinding and polishing.Materials and methodsData were collected from 207 dentists and 125 dental assistants through an online questionnaire. The questionnaire included adjusted prosthesis types, self-protective methods, types and frequency of protective device use, and reasons for non-frequent use.ResultsProtective grinding devices, including dust protective boxes and mounted plastic sheets, were commonly used for substantial acrylic resin adjustments, while air blowing was preferred for minor adjustments. Post-COVID-19, there was a 3-fold increase in the use of protective grinding devices among dentists and a 1.3-fold increase among dental assistants. During try-in procedures, dentists commonly rinsed prostheses with water rather than using disinfectants. Non-frequent users adopted self-protection methods, such as face shields and air filters. Surgical drapes and high-volume evacuators were used for patient’s protection.ConclusionDespite an increased tendency of the use of protective grinding devices following COVID-19, a significant number still report infrequent use. Identified protective devices in this study have drawbacks not fully meeting dentists’ expectations. Invention of a more user-friendly device is necessary to ensure regular use, preventing potential toxicity from dust particles.

Characterization of Village Chicken Production Systems in Three Agro-climatic Zones of Western Tigray, Northern, Ethiopia

A survey was conducted in Tigray, Northern Ethiopia, to characterize village chicken production systems using a questionnaire and group discussions. Data was analyzed using SPSS 22. Respondents provided supplementary feeds to chickens to improve yields and health. Sorghum, maize, sesame, tomato, onion, barley, and household food leftovers were the main supplementary feeds, although the types of cereal crops produced varied across agro-climates. Harvest and purchase were main sources of cereal and non-cereal chicken feeds, respectively. 50.4% considered summer, 48.8% winter as critical feed seasons. Farmers provided feeds to their chickens in the morning (98.7%), afternoon (69.6%), and evening (81.3%), and on the ground for collective feeding (97.9%). 59.5% of respondents constructed separate chicken houses, with 56.1% being permanent structures and 3.4% temporary. Chicken houses were constructed using materials such as mud, wood, iron sheet roofing, bamboo, grass, and plastic. 57.7% cleaned chicken houses, 66% once daily, and 2.1% not at all. Water was provided ad libitum (70.9%), once a day (7.5%), or twice a day (21.6%) from wells, taps, or rivers using various waterers. Eighty-six percent of the respondents cleaned chicken waterers, while the remaining 14% did not. Training is needed for house construction, feeding, watering, cleaning, and disinfection of feeders and waterers to prevent waterborne diseases.

Immobilization of rare-earth doped aluminate nanoparticles encapsulated with silica into polylactic acid-based color-tunable smart plastic window

An inorganic/organic nanocomposite was used to develop an afterglow and color-tunable smart window. A combination of polylactic acid (PLA) plastic waste as an environmentally-friendly hosting agent, and lanthanide-activated strontium aluminum oxide nanoparticles (SAON) encapsulated with silica nanoparticles (SAON@Silica) as a photoluminescent efficient agent resulted in a smart organic/inorganic nanocomposite. In order to prepare SAON-encapsulated silica nanoparticles (SAON@Silica), the SAON nanoparticles were coated with silica using the heterogeneous precipitation method. By using transmission electron microscopy (TEM), SAON showed a diameter range of 5–12 nm, while the SAON@Silica nanoparticles showed a diameter range of 50–100 nm. In order to ensure the development of a colorless plastic film, a homogeneous dispersion of the phosphorescent Phosphor@Silica nanoparticles throughout the plastic bulk was confirmed. CIE Lab coordinates and luminescence spectra were used to study the color shift characteristics. Under visible light conditions, the plastic films were transparent. The photoluminescent films emitted green light at 525 nm when excited at 375 nm. The hydrophobicity and ultraviolet protection were enhanced without altering the fundamental physico-mechanical performance of the plastic sheet. The current color-tunable plastic can be used in many potential applications, such as warning signs, anti-counterfeiting barcodes, smart windows, and protective apparel.

Towards Climate Resilience: A Comprehensive Study on Eco-Friendly Alternatives for Single-Use Plastic Sheets in Somalia

This research critically examines the recent policy intervention by the Somali government, focusing on the prohibition of single-use plastic sheets. The primary aim is to safeguard the environment and enhance public safety, aligning with global efforts to address plastic pollution and promote sustainable practices. The government's proactive approach urges manufacturers to explore alternative materials that prioritize community well-being and minimize environmental impact. This research, in response to the government's call for action, seeks to contribute comprehensive strategies that complement existing efforts. One key facet of the proposed initiatives involves research and development to identify and promote eco-friendly substitutes for single-use plastic sheets. This includes investigating materials with minimal environmental impact throughout their lifecycle. By encouraging innovation in materials science, the study aims to support the government's commitment to sustainable practices and reduce dependence on harmful substances. In addition to material innovation, the research emphasizes the importance of awareness campaigns to educate the public about the environmental and social implications of plastic usage. Community awareness is crucial for fostering a collective understanding of the need for change and garnering support for the government's policies. This aspect of the study aims to develop targeted communication strategies to engage diverse segments of the population and promote a culture of responsible consumption. Furthermore, the research advocates for the implementation of recycling programs to manage existing plastic waste effectively. Developing robust waste management infrastructure is essential for ensuring that discarded plastic materials are recycled efficiently, reducing their impact on the environment. Recognizing the economic aspects of the transition, the research proposes incentives for businesses that adopt sustainable materials. These incentives can include financial support, tax breaks, or preferential treatment in government procurement processes. By aligning economic interests with ecological responsibility, the study aims to facilitate a smooth transition and encourage widespread adoption of sustainable practices. Through a comprehensive analysis of various initiatives, the research aims to provide actionable insights for policymakers. Recommendations will be formulated to guide the government in implementing effective measures that align with its commitment to environmental sustainability and the overall safety of the Somali population. In conclusion, this research aspires to contribute practical strategies for Somalia, balancing economic interests with ecological responsibility. By fostering a harmonious coexistence between human activities and the environment, the study aims to support the government's vision of a resilient and sustainable future.

Sunlight can have a stronger influence than air temperature on soil solarisation: observational evidence from Australia

Soil solarisation is a method for pest and weed control pioneered in agriculture, and it is increasingly being adopted by restoration practitioners. Solarisation works by covering moist soil during hot periods with a sheet of clear plastic. The success of soil solarisation depends in large part on increasing the temperature of the topsoil. Topsoil temperature depends on several physical variables, including soil moisture content, ambient temperature, and sunlight intensity. In restoration scenarios, solarisation can be used to reduce weed and pathogen loads prior to planting target plants. It is rarely possible to have tight control over all the variables that are important for solarisation; however, practitioners can time interventions to maximise seasonal temperature and sunlight intensity. In this study, we investigated how these two key physical variables – temperature and sunlight – contributed to the success of soil solarisation. We found that while both ambient temperature and sunlight contributed to soil temperature, the data suggests that sunlight was the more influential driver of soil temperature. These results show that, when planning for soil solarisation during ecological restoration, land managers can benefit by considering sunlight as well as air temperature. The result that sunlight may be the more influential driver of soil temperature empowers land managers to better plan solarisation using sunlight projections, even when temperature is not optimal or is unpredictable.

Chameleon inspired high-temperature thermochromic traffic light type photonic crystal sensors toward early fire detection and visual sensing

Fire detection plays a crucial role in maintaining the safety of people’s lives and property. However, most early fire detectors are designed to monitor the current or voltage changes of the sensing materials, which require external power supplies. It is still a challenge to make rapid and accurate noncontact early fire detection in precombustion due to the lack of reliable alarm signals. Herein, inspired by the discoloration of chameleon skin, we developed an early fire warning sensor (EFWS) by coating photonic crystals (PCs) on a plastic sheet with thermal expansion properties. Monodispersed zinc sulfide (ZnS) was coated on the plastic sheet as abnormal detection component for EFWS. Combined with the intelligent image recognition algorithm, the EFWS was designed and gave warnings for 0.9 s at 260 °C. For the first time, a photonic crystal-based non-contact real-time monitoring EFWS in precombustion is developed. The sensing material can be directly pasted on the surface of the detected equipment, and combined with existing surveillance cameras in the detection area, early warning of fires can be achieved. The EFWS system can be used in non-open fire alarms for aircraft, buildings, electrical appliances, substations, and other places in the future.

Characterization of Shrink Film Properties for Rapid Microfluidics Lab-on-Chip Fabrication.

Shrink film is a thin sheet of polystyrene plastic that shrinks to 25-40% of its original size when heated. This study investigated the shrinkage factor of the film at different temperatures and baking times to determine the optimal fabrication recipe for shrink film microfluidic device production. Additionally, this study characterized the properties of shrink film, including minimum possible feature size and cross-section geometries, using manual engraving and the CAMEO 4 automated cutting machine. The optimal shrinkage factor ranged from 1.7 to 2.9 at 150 °C and a baking time of 4 min, producing the ideal size for microfluidic device fabrication. The X- and Y-axes shrank ~2.5 times, while Z-axis thickened by a factor of ~5.8 times. This study achieved a minimum feature size of 200 microns, limited by the collapsing of channel sidewalls when shrunk, leading to blockages in the microchannel. These findings demonstrate the feasibility and versatility of using shrink film as a cost-effective and efficient material for the rapid fabrication of microfluidic devices. The potential applications of this material in various fields such as the medical and biomedical industries, bacteria and algae culture and enumeration are noteworthy.

Multi-objective optimization of composite sandwich structures using Artificial Neural Networks and Genetic Algorithm

Sandwich structures offer significant opportunities to improve the performance of many industrial applications such as aerospace, automotive, and marine. The design of a composite sandwich structure is often challenging because it is driven by the balance between the weight and cost of these structures. In this paper, a multi-objective optimization model using a Genetic Algorithm (GA) and an Artificial Neural Network (ANN) is presented to evaluate a new optimization approach in terms of weight and cost minimization for the composite sandwich structures. Classical lamination and beam bending theories were used, along with Monte Carlo simulation, to generate the design data for the proposed composite sandwich structure, which is applied as a floor panel for a high-speed train. Multilayer feedforward neural networks were used for predicting safety factors, cost, and weight of the designed structure based on the following inputs: core density, core thickness, face sheet materials’ combinations, and applied load. The trained Neural Network model was able to predict the considered results with a good performance metric, namely the coefficient of determination (R2 = 0.99) and the Mean Square Error (MSE = 1.3·10−5).Multi-objective optimization for cost and weight minimization was performed with a Genetic Algorithm using the derived ANN model. The obtained Pareto front provided several non-dominated optimal points leading to insights on the optimization process. The Finite Element Method (FEM) was used to model the key points of the optimal designs (i.e. the design with the lowest cost, weight, and Pareto optimal points). The FEM and optimization results had a maximum deviation of about 8.9%, indicating a good agreement between the two techniques.The newly elaborated methodology demonstrates a new approach for obtaining the optimum design of the investigated composite sandwich structure constructed from honeycomb core and laminated face sheets in terms the cost and weight. The study concluded that the use of Carbon Fiber-Reinforced Plastic (CFRP) or Fiber-Metal Laminate (FML) face sheets results in significant weight savings of about 59.5% and 48.6%, respectively, compared to an all-aluminum sandwich structure.

Johnson Grass (Sorghum halepense) Interference, its Effect on Crops Yield and Soil attributes under Different Cropping Systems and Management Practices

Johnson grass (Sorghum halepense) is one of the most detrimental and toxic weeds among the weed species. Its environment is expanding unceasingly due to deeply expanding of its rhizomes in the soil, self-pollinating reproduction strategy, accelerated growth and poor management which results in production losses of major agronomic crops. Mungbean and sorghum are important crops grown on significant acreage around the world, and a major constraint for their production losses is weeds interference. Thus, field studies were conducted to examine Johnson grass interference, control, and recovery under different management practices and cropping system and its effects on crops production and soil health. Our results indicated that the Johnson grass density was minimized by the application of plastic sheet mulch treatment under wheat-mungbean cropping system. Johnson grass competition had a significant impact on growth and grain yield of both mungbean and sorghum. The crop yield parameters; 100 grain weight and grain yield were lowest in the non-treated treatment (control), while the greatest values of these parameters were recorded in the plastic sheet mulch and post emergence herbicide treatments with wheat-mungbean cropping system. Similarly, soil building attributes; available nitrogen, available phosphorus, available potassium and organic matter content were positively affected by the interaction of plastic sheet mulch + wheat-mungbean cropping system. Besides this, benefit-cost ratio of the research shows that wheat-mungbean cropping system with application of plastic sheet mulch and post emergence herbicide also proved to be economically feasible. Overall, we have concluded that wheat-mungbean and wheat-sorghum are most resilient cropping system with the implementation of plastic sheet mulch and Post Emergence Herbicide to suppress the spread of Johnson grass under changing climatic scenarios.

Setups for eliminating static charge of the ATLAS18 strip sensors

Construction of the new all-silicon Inner Tracker (ITk), developed by the ATLAS collaboration to beable to track charged particles produced at the High-Luminosity LHC, started in 2020 and is expected tocontinue till 2028. The ITk detector will include 18,000 highly segmented and radiation hard n+-in-psilicon strip sensors (ATLAS18), which are being manufactured by Hamamatsu Photonics. Mechanical and electrical characteristics of produced sensors are measured upon their delivery at several institutes participating in a complex Quality Control (QC) program. The QC tests performed on each individual sensor check the overall integrity and quality of the sensor.During the QC testing of ATLAS18 strip sensors, an increased number of sensors thatfailed the electrical tests was observed. In particular, IV measurements indicated an early breakdown,while large areas containing several tens or hundreds of neighbouring strips with low interstrip isolationwere identified by the Full strip tests, and leakage current instabilities were measured in a long-term leakage current stability setup. Moreover, a high surface electrostatic charge reaching a level of several hundreds of volts per inch was measured on a large number of sensors and on the plastic sheets, whichmechanically protect these sensors in their paper envelopes. Accumulated data indicates a clearcorrelation between observed electrical failures and the sensor charge-up.To mitigate the above-described issues, the QC testing sites significantly modified the sensor handlingprocedures and introduced sensor recovery techniques based on irradiation of the sensor surface with UVlight or application of intensive flows of ionized gas. In this presentation, we will describe the setupsimplemented by the QC testing sites to treat silicon strip sensors affected by static charge andevaluate the effectiveness of these setups in terms of improvement of the sensor performance.