Dielectric Barrier Discharge Plasma Research Articles

Dielectric Barrier Discharge Plasma Combined with Ce-Ni Mesoporous catalysts for CO2 splitting to CO

Dielectric Barrier Discharge Plasma Combined with Ce-Ni Mesoporous catalysts for CO2 splitting to CO

Enhancing CO2 conversion in a temperature-controlled DBD plasma reactor with HKUST-1 catalyst: Water removal and CuO/Cu2O-derived approach

Due to a synergy effect, using dielectric barrier discharge (DBD) plasma technology combined with catalysts for CO2 decomposition, a major contributor to global warming, is recognized as an effective approach to transforming CO2 into valuable products such as CO, which is a crucial feedstock for chemical synthesis. Herein, HKUST-1 was synthesized using the hydrothermal method for CO2 conversion in the DBD reactor. To enhance catalyst performance in the plasma region, HKUST-1 was treated with O2 plasma to increase its specific surface area. Additionally, HKUST-1 was calcined at 300 °C to produce the CuO/Cu2O catalyst. Since the recombination reaction in the CO2 conversion is increased at higher temperatures, the reactor heat is removed using fan cooling and a water circulation system. In the presence of the HKUST-1 catalyst, the CO2 conversion rate significantly increased by 132 %, 82 %, and 12 % in reactors operating without cooling, with fan cooling, and with water cooling circulation, respectively compared to the reactors without catalyst, at a flow rate of 50 ml/min and maximum input power. The catalysts have been characterized using a comprehensive suite of analytical techniques, including FTIR, XRD,TEM, SEM, EDS, and BET analysis. The BET analysis indicates that the specific surface area of HKUST-1 after O2 plasma treatment is increased by 52 %, which causes an increasing conversion rate of up to 18 %. The CuO/Cu2O catalyst demonstrated maximum CO2 conversion of 21 % at an input power of 140 W and achieved energy efficiency of 8.6 % at 40 W. The presence of oxygen vacancies within this catalyst enhances the process of CO2 decomposition.

Inductive plasma excitation forcing configuration on reduction of tip distorted inflow effect on the aerodynamic stability of axial compressor rotor

This research delves into the mitigating impacts of dielectric barrier discharge (DBD) plasma excitation induced forcing orientation against the detrimental consequences of distinct radial tip distortions which in turn affect the axial compressor rotor performance and alters the flow structure at the tip region. Full annulus transient CFD simulation was utilized to evaluate the consequences of plasma actuation at distorted conditions with different blockage percentages. Beyond flow field and frequency analysis, the study further characterized rotor performance under different conditions by evaluating key performance metrics, including total pressure rise coefficient, stall margin variation, and span-wise rotor inlet velocity distribution. The injection of momentum caused by plasma actuators to the low-energy region behind the distortion screens proved to be effective on rotor aerodynamic stability facing radial tip distortion. In the case where 15 % of the inlet area was blocked, the stall margin varied from -8 % to -3.5 % with axial plasma actuators in action. However, the best configuration of plasma actuators for the enhancement of the stall margin and flow characteristics was identified to have opposite forcing direction with respect to the rotor rotational velocity. Additionally, these actuators suppressed frequencies caused by fluctuations in the rotor blade row tip leakage vortex, suggesting an improvement in the flow pattern within the rotor tip area.

Dielectric barrier discharge plasma in-situ microbubble aeration with peroxymonosulfate for levofloxacin degradation: Microbubble superior performance and pH-dependent mechanism

In this study, a simple ceramic membrane aeration was used to realize dielectric barrier discharge/peroxymonosulfate (DBD/PMS) in-situ microbubble aeration for effective dispersion and gas–liquid transfer of highly active substances. Compared with conventional aeration, ceramic membrane aeration had 18 times fewer microbubble diameters (110–180 µm), much higher bubble densities, and 1.6–2.1 times higher aquatic O3 concentrations at pH 4.8–10.0. Consequently, the yield of HO and SO4·- was 1.64–2.34 and 1.13–2.93 times, respectively, via faster O3 transfer to the aquatic solution and enhanced PMS activation. DBD/PMS microbubble aeration outperformed conventional aeration, with a 2.52-fold increase in LEV degradation kinetics and a 2.79-fold increase in TOC removal. Quenching and EPR experiments showed that HO and 1O2 were the main reactive oxygen species (ROS) for LEV degradation. The yield of O2·- was higher at pH 6.9, while HO, SO4·-, and 1O2 was higher at pH 8.7 derived from a series of complex reactions. The LEV degradation pathway was pH-dependent, with the HO-oxidation contribution varying from 25.3% to 44.3% as the pH increased from 4.8 to 8.7, while other ROS (1O2 and O2·-)-oxidation decreased from 73.1% to 51.8%. Therefore, this work will advance the current understanding of the intrinsic effects of pH in the plasma/PMS microbubble process for wastewater purification.

The Role of Gas-Liquid Interface in Controlling the Reactivity of Air Dielectric Barrier Discharge Plasma Activated Water

The Role of Gas-Liquid Interface in Controlling the Reactivity of Air Dielectric Barrier Discharge Plasma Activated Water

Spatiotemporal evolution laws of sector-shaped dielectric-barrier-discharge plasma actuator

Dielectric barrier discharge (DBD) plasma actuators are widely used in active flow control due to their simple design and rapid responsiveness. However, they need more effectiveness and discharge extension. To overcome these limitations, a sector-shaped dielectric barrier discharge (SS-DBD) plasma actuator with an adjustable jet angle was developed to enhance flow control effectiveness. The flow field dynamics induced by the SS-DBD plasma actuator were quantitatively analyzed using particle image velocimetry (PIV). Experimental investigations showed that precise adjustments to the actuation voltage can modulate the maximum velocity of the induced jet. Furthermore, a quasi-linear relationship between the sector-shaped angles of the SS-DBD and the deflected jet angles was established, indicating that changes in the sector-shaped angles directly influence the direction of the deflected jet. This correlation enables precise control over jet angles, significantly enhancing flow control by adjusting the SS-DBD-PA’s sector-shaped angle.

Passion fruit peel-derived low-methoxyl pectin: De-esterification methods and application as a fat substitute in set yogurt

Passion fruit pectin, originally high methoxyl pectin, undergoes substantial conversion into low methoxyl pectin (LMP) through de-esterification. This de-esterification is significance for reducing the application of sugar in food, as calcium ions can replace excessive sugar during gel formation. In this study, LMPs derived from passion fruit pectin were prepared using four methods: low-temperature alkali, room temperature alkali, enzymatic, and dielectric barrier discharge plasma (DBD)-assisted enzyme (DBDE). The de-esterification conditions were optimized, leading to the selection of LMPs with a degree of esterification for the analysis of molecular weight, monosaccharide composition, and gel properties. The results revealed significant differences in the structure and properties of LMPs depending on the de-esterification method applied. The galacturonic acid content of LMPs significantly increased, with LMP from DBDE (LMP-DBDE) exhibiting the highest increase at 47.81 %. Additionally, the molecular weights of LMPs significantly decreased, with LMP-DBDE showing the smallest decrease. LMP-DBDE demonstrated higher apparent viscosity, thermal stability, and gel properties, facilitating the formation of gels. After 21 days of storage, 0.40 % LMP-DBDE yogurt showed no whey separation, significantly extending its shelf life. Therefore, LMP-DBDE exhibits potential as a fat substitute, combining the advantages of LMP with enhanced water-holding capacity, and presenting promising applications in low-fat dairy products.

Studies of dynamic spatio-temporal processes of electrons in a 50 kHz/5 MHz dual-frequency dielectric barrier discharge plasma at atmospheric pressure

Dual-frequency excitation of dielectric barrier discharge (DBD) plasma reactors, where the plasma is generated by a low-frequency (LF) source and modulated by a radio-frequency (RF) source, have been widely adopted in the low-pressure regime. However, the impacts of the RF voltage and LF voltage amplitudes on the plasma parameters, including the spatiotemporal distributions of ion and electron densities, electron dynamics, and gas temperatures, remain poorly understood in the atmospheric pressure regime. The present work addresses this issue by conducting joint experimental and simulation studies for an atmospheric-pressure 50 kHz/5 MHz dual-frequency driven DBD plasma reactor based on phase-resolved optical emission spectra and a drift–diffusion model. The results demonstrate that the dynamic spatiotemporal behaviors of electrons change dramatically as the voltage of the RF component increases from 50 V to 300 V with the voltage of the LF component fixed at 1 kV. Moreover, the RF component is further demonstrated to modulate other plasma characteristics, such as particle densities, gas temperature, and argon emissions. These results contribute toward the tailoring of the non-equilibrium and nonlinear plasma parameters obtained under atmospheric pressure conditions.

Degradation of thiamphenicol by La-Fe2O3/DBD/HCP synergistic catalytic system

In this study, a highly efficient La-Fe2O3/dielectric barrier discharge (DBD)/honeycomb ceramic plate synergistic catalytic system was successfully constructed by using modified iron oxide (Fe2O3) catalyst coating assisted DBD plasma, and the prepared catalytic coating was fully characterized by various techniques. The results indicate that the lanthanum (La) is efficiently and uniformly doped in Fe2O3, and the modified La-Fe2O3 catalyst exhibited a better photocatalytic performance. The overuse of Thiamphenicol (TAP), as a typical chloramphenicol antibiotic, has led to its accumulation in the aquatic environment. Accordingly, TAP was selected as the target contaminant to evaluate the catalytic activity of the synergistic system. The results confirmed that the catalytic ability of the synergistic catalytic system was significantly improved, and the data showed that the degradation rate of the synergistic system reached 99.1% under the same conditions compared with 68.2% for the single DBD plasma, which effectively improved low energy efficiency limitations of the single DBD technology. Through quantitative measurements of the concentrations of dissolved ozone (O3) and hydrogen peroxide (H2O2) in the system and radical trapping experiments, combined with emission spectroscopy, the mechanism of synergistic system degradation of TAP was analyzed. The intermediates in the degradation process were characterized by high-resolution mass spectrometry, and the degradation pathway of TAP was proposed based on the analysis of the intermediates and their combination with theoretical calculations. This study presents a theoretical basis for the improvement of DBD technology and a technical guide for the removal process of antibiotics from industrial wastewater.

Mechanistic study on 4, 4'-sulfonylbis removal with CO2/Ar gas-liquid DBD plasma

In this study, a single dielectric barrier discharge (DBD) coaxial reactor was used to degrade 4, 4'-sulfonylbis (TBBPS) in water using greenhouse gas (CO2) and argon as the carrier gases. The investigation focused on CO2 conversion, reactive species formation, gas-liquid mass transfer mechanism, and degradation mechanism of TBBPS during the discharge plasma process. With the decrease of CO2/Ar ratio in the process of plasma discharge, the emission spectrum intensity of Ar, CO2 and excited reactive species was enhanced. This increase promoted collision and dissociation of CO2, resulting in a series of chemical reactions that improved the production of reactive species such as ·OH, 1O2, H2O2 and O3. These reactive species initiated a sequence of reactions with TBBPS. Results indicated that at a gas flow rate of 240 mL/min with a CO2/Ar ratio of 1:5, both the highest CO2 conversion rate (17.76%) and TBBPS degradation rate (94.24%) were achieved. The degradation mechanism was elucidated by determining types and contents of reactive species present in treatment liquid along with analysis of intermediate products using liquid chromatography-mass spectrometry techniques. This research provides novel insights into carbon dioxide utilization and water pollution control through dielectric barrier discharge plasma technology.

Study of three-dimensional spatial diffuse discharge in contact electrode structure applied to air purification

In this work, based on the role of pre-ionization of the non-uniform electric field and its effect of reducing the collisional ionization coefficient, a diffuse dielectric barrier discharge plasma is formed in the open space outside the electrode structure at a lower voltage by constructing a three-dimensional non-uniform spatial electric field using a contact electrode structure. The air purification study is also carried out. Firstly, a contact electrode structure is constructed using a three-dimensional wire electrode. The distribution characteristics of the spatial electric field formed by this electrode structure are analyzed, and the effects of the non-uniform electric field and the different angles of the vertical wire on the generation of three-dimensional spatial diffuse discharge are investigated. Secondly, the copper foam contact electrode structure is constructed using copper foam material, and the effects of different mesh sizes on the electric field distribution are analyzed. The results show that as the mesh size of the copper foam becomes larger, a strong electric field region exists not only on the surface of the insulating layer, but also on the surface of the vertical wires inside the copper foam, i.e., the strong electric field region shows a three-dimensional distribution. Besides, as the mesh size increases, the area of the vertical strong electric field also increases. However, the electric field strength on the surface of the insulating layer gradually decreases. Therefore, the appropriate mesh size can effectively increase the discharge area, which is conducive to improving the air purification efficiency. Finally, a highly permeable stacked electrode structure of multilayer wire-copper foam is designed. In combination with an ozone treatment catalyst, an air purification device is fabricated, and the air purification experiment is carried out.

Comprehensive study of plasma polymerization parameters on thiol-coated LDPE films for effective fibronectin adsorption targeting biomedical applications

In the realm of biomedical applications, biocompatible materials with optimized surface properties are crucial for facilitating cellular interactions. To attain the perfect balance of these properties, surface modification of non-toxic and stable bulk materials is often required. Within this context, this research aimed to improve the physiochemical and cell-responsive properties of a low-density polyethylene film. This was achieved by depositing thiol-rich coatings using a dielectric barrier discharge plasma reactor operating at medium pressures, with 1-propanethiol serving as polymerization precursor. The study systematically investigated the impact of key plasma polymerization parameters, including DBD chamber pressure, treatment time, and the combination of precursor flow rate and discharge power represented by the Yasuda parameter, to identify optimal plasma processing conditions for the formation of thiol-rich coatings. To characterize the coating thickness, hydrophilicity and surface chemical composition, atomic force microscopy, water contact angle measurements, and X-ray photoelectron spectroscopy were employed. The findings indicated that reducing the chamber pressure to 10 kPa led to more hydrophilic and thicker deposits possessing a higher sulphur content. Deposition time (5 to 15 min) also significantly impacted coating thickness and surface chemistry, where long times increased thickness, but also led to a reduced sulphur and increased oxygen content because of more pronounced etching. The optimal deposition time was therefore set at 10 min resulting in the deposition of dense coatings possessing a high number of sulphur-containing functionalities. The Yasuda parameter (W/FM) analysis demonstrated optimal thiol incorporation in combination with high coating stability at an intermediate W/FM value of 72 MJ/kg. Following the determination of the optimal plasma polymerization parameters, the effectiveness of thiol plasma polymerization and subsequent fibronectin immobilization for enhancing cell adhesion and proliferation was investigated. The thiol-coated substrates were found to exhibit superior protein immobilization, because of the high affinity for protein binding of the available thiol groups. To assess cellular responses, Schwann cells were cultured on uncoated and coated samples before and after fibronectin immobilization. The results revealed a superior cellular response of the thiol-coated samples after fibronectin immobilization, showing the highest cell viability and significantly enhanced cell adhesion and proliferation. Collectively, these results underscore the synergistic effect of thiol plasma polymerization and fibronectin immobilization in promoting the cellular response of LDPE substrates, thus highlighting their potential as a surface modification strategy of biomaterials.

Enhancing the biological activities and altering the chemical structure of clove aqueous extract prepared with plasma-activated water as a novel technique

This investigation assesses the effect of plasma-activated water (PAW) as a solvent during the preparation of clove aqueous extract. PAW was generated by surface dielectric barrier discharge (SDBD) plasma device for 5, 10, and 15 min, respectively. The conventional method of maceration was used as a control group. We evaluated the biological activity and physicochemical characteristics of clove extracts. In the color assay, the clove extract produced by PAW showed a slightly higher color parameter than the control extract. The Fourier transform infrared (FTIR) results demonstrated several higher absorption intensities at specific regions in the PAW-clove extract structure. Liquid chromatography-mass spectrometry (LC-MS) analysis of the PAW extracts showed more bioactive components than the maceration extract. The clove extract prepared by the PAW -5 min group had the highest total phenolic content (TPC) at 821.6 mg GAE/g, the highest free radical scavenging activity (DPPH) and ferric-reducing antioxidant power (FRAP) compared to other groups. These alterations could be due to reactive oxygen-nitrogen species (RONS) generated in PAW, which can modify the physicochemical properties of clove. The findings indicated that PAW is a unique extraction solvent that improves the extraction of phenolic compounds from clove.

The effect of polysaccharide type on dielectric barrier discharge (DBD) plasma glycosylation of sodium caseinate-part I: Physicochemical, structural and thermal properties

This study aimed to investigate the impact of polysaccharide type on the physicochemical, structural, and thermal properties of dielectric barrier discharge (DBD) plasma glycosylated sodium caseinate (SC). The polysaccharides Quince seed gum (QSG), carboxymethyl cellulose (CMC), and maltodextrin (MD) were mixed with SC and treated with DBD plasma at 18 kV for 10 min. The grafting degree, electrophoresis pattern, FTIR, XRD, carbonyl, sulfhydryl, and di-tyrosine content, FE-SEM, color, and thermal properties of SC and its polysaccharide mixtures before and after plasma treatment were analyzed. Results showed that the SC-QSG conjugate had the highest glycation degree and color change after plasma treatment. The SC-CMC and SC-QSG conjugates exhibited disappearance of distinct SC bands in electrophoresis pattern compared to SC. Also, significant changes in functional group and crystallinity were occurred in SC-CMC conjugate. Plasma treatment caused oxidation of SC, but the presence of polysaccharides offered protection against oxidation. The microstructure of SC was altered by mixing with polysaccharides and exposure to plasma. Also, the mixtures indicated higher thermal stability after plasma treatment. Results confirmed that the generation of protein-polysaccharide conjugates through DBD plasma technique was depended on with SC-MD conjugate unable to form through this method.

Research and Analysis on Enhancement of Surface Flashover Performance of Epoxy Resin Based on Dielectric Barrier Discharge Plasma Fluorination Modification.

To conquer the challenges of charge accumulation and surface flashover in epoxy resin under direct current (DC) electric fields, numerous efforts have been made to research dielectric barrier discharge (DBD) plasma treatments using CF4/Ar as the medium gas, which has proven effective in improving surface flashover voltage. However, despite being an efficient plasma etching medium, SF6/Ar has remained largely unexplored. In this work, we constructed a DBD plasma device with an SF6/Ar gas medium and explored the influence of processing times and gas flow rates on the morphology and surface flashover voltage of epoxy resin. The surface morphology observed by SEM indicates that the degree of plasma etching intensifies with processing time and gas flow rate, and the quantitative characterization of AFM indicates a maximum roughness of 144 nm after 3 min of treatment. Flashover test results show that at 2 min of processing time, the surface flashover voltage reached a maximum of 19.02 kV/mm, which is 25.49% higher than that of the untreated sample and previously reported works. In addition to the effect of surface roughness, charge trap distribution shows that fluorinated groups help to deepen the trap energy levels and density. The optimal modification was achieved at a gas flow rate of 3.5 slm coupled with 2 min of processing time. Furthermore, density functional theory (DFT) calculations reveal that fluorination introduces additional electron traps (0.29 eV) and hole traps (0.38 eV), enhancing the capture of charge carriers and suppressing surface flashover.

Control of Flow and Acoustic Fields Around an Axial Fan Utilizing Plasma Actuators

Abstract Small axial fans, commonly employed for cooling electronic equipment, are frequently housed within narrow ducts, where intense tonal sound with duct resonance can occur, particularly when the blade passing frequency or its harmonic frequency aligns with the duct's resonance frequency. To mitigate resonant sound, this study proposes a flow control using dielectric barrier discharge plasma actuators, which induce a flow along the generation of plasma in air. The control effects on flow field, acoustic radiation, and aerodynamic characteristics are evaluated through direct aeroacoustic simulations and experiments conducted at different flow rates. The computational results reveal that swirling flow occurs in the inflow due to fan rotations at low flow coefficients. This swirling flow is weakened by utilizing plasma actuators, which are arranged to induce flows in the circumferentially reverse direction compared to fan rotations. This control method weakens the resonant sound at low and intermediate flow coefficients, while intensifying it at high flow coefficients, all at the same rotational speed. Moreover, the static pressure coefficient decreases and increases at low and high flow coefficients, respectively, with the latter attributed to an increase in the relative inflow angle induced by the control. Experimental findings demonstrate that the acoustic resonance was reduced by the control at both low and high flow rates, achieved by adjusting the rotational speed to maintain the same flowrate and static pressure rise as in the baseline case.

Enhancing Selectivity with Molecularly Imprinted Polymers via Non-Thermal Dielectric Barrier Discharge Plasma.

Molecularly imprinted polymers (MIPs) are synthetic polymers that mimic the functions of antibodies. Though MIPs are promising tools in various areas, achieving high selectivity in MIPs can be difficult. To improve selectivity, various approaches have been implemented; however, the role of polymerization methods or synthetic techniques in enhancing the selectivity of MIPs has not been studied and remains a crucial area for further research. MIPs are typically prepared from free radical reactions. Recently, we found that Dielectric Barrier Discharge (DBD) plasma can be used to initiate the polymerization of vinyl monomers. The DBD plasma method allows the monomers to associate with the template molecules and initiate polymerization with minimal disruption to the positioning of the monomers. We hypothesize that this could be a preferred method to prepare MIPs over the traditional radical reaction that may cause a disturbance of the pre-associated monomers on the templates for the polymerization. Chicken egg white serum albumin (CESA) was used as the template protein for the MIPs. Our results show that in all test conditions, approximately twofold improvement in selectivity was achieved, which is the primary performance metric for MIPs. This enhancement was evident across all categories, including MIPs prepared from various monomer combinations.

Bayesian Optimization of Low-Temperature Nonthermal Plasma Jet Sintering of Nanoinks.

In response to the escalating demand for flexible devices in applications such as wearables, sensors, and touch panels, there is a need for innovative fabrication approaches for devices made from nanomaterial-based inks. Subsequent to ink deposition, a pivotal stage in device manufacturing typically involves high-temperature sintering, posing challenges for heat-sensitive substrates. Nonthermal plasma jet sintering utilizing an atmospheric pressure dielectric barrier discharge (DBD) plasma jet enables sintering at room temperature and standard pressure, facilitating the sintering of printed nanoparticle films without compromising substrate or film surface integrity. However, determining optimal plasma jet sintering conditions can be challenging due to multiple processing variables with intricate interrelationships. This work employed Bayesian optimization (BO) and machine learning (ML) to identify optimal values for seven primary plasma jet sintering variables. Optimization yielded a 99.2% increase in the measured electrical conductivity for plasma jet-sintered indium tin oxide (ITO) films after five rounds of experiments. Moreover, the optimal sintering conditions achieved an electrical conductivity that was 81.4% of conventional furnace sintering at 300 °C, but was three times faster and with a peak substrate temperature below 47 °C. This result demonstrates the prospect of applying BO to optimize processing techniques for emerging low-temperature requirements.

Evolutionary distribution and mode transition in medium frequency from 50 kHz to 5 MHz of argon atmospheric pressure dielectric barrier discharge plasma

Dielectric barrier discharges (DBDs) provide a promising technology for generating non-equilibrium cold plasmas at atmospheric pressure. For both application-focused and fundamental research, it is important to explore the discharge mode transition and electron heating mechanism to enable effective independent tuning of key plasma parameters in a DBD system. In this work, we report numerical studies of the effects of single-frequency excitation on atmospheric argon DBDs, which are carried out in the medium driving frequency (MF) range from 50 kHz to 5 MHz by using a one-dimensional hydrodynamics coupling model. The spatio-temporal evolution of particle density associated with the discharge mode transition and electron dynamic behavior has been investigated. By tuning different components of a single frequency, we observe the electron heating behaviors of the individual modes and mode transitions from the Townsend discharge to the glow discharge in the low frequency to the Ω mode and the hybrid mode in the medium frequency to the α-mode and the γ-mode in the radio frequency. The physical analysis is understood based on these fundamental insights into the plasma physics.

Surface dielectric barrier discharge plasma inactivates white colony-forming yeast in kimchi seasoning

White colony-forming yeast (WCFY) is a major source of food spoilage. Although it does not cause cytotoxic reactions, WCFY on kimchi results in unpleasant odors that are unappealing to consumers, resulting in economic losses and food wastage. Chemical and physical disinfection methods for kimchi have limitations. Surface dielectric barrier discharge (S-DBD) plasma treatment is a recent innovation that shows promise for inactivating WCFYs; however, this approach has not yet been tested in kimchi. Therefore, in this study, we aimed to investigate whether S-DBD plasma treatment of WCFY Kazachstania servazzii inhibits colony formation in kimchi seasoning during storage. Through visual confirmation, we found that the optimized S-DBD plasma treatment effectively inhibited WCFY formation. Moreover, treatment with S-DBD plasma exerted only an anti-WCFY effect and did not significantly change the physicochemical properties (e.g., pH, titratable acidity, volatile organic compounds) of the kimchi seasoning samples, indicating that the quality was preserved. Maximum WCFY reduction occurred at 67.8% relative humidity, 120.0 min treatment time, and 15.1 °C. In conclusion, S-DBD plasma treatment is an effective alternative to current anti-yeast approaches and has the potential to improve the quality of kimchi production.