Photoelectrochemical Properties Research Articles

Enhanced electron storage capacity achieved by coupling NiO with WO3/BiVO4 for persistent photocathodic protection of 316 stainless steel

Employing a photoanode with energy self-storage capability is crucial to provide continuous photocathodic protection (PCP) for metal under intermittent irradiation. In this work, NiO, a hole collector, was coupled with WO3/BiVO4 to improve photoelectrochemical properties and photocathodic protection ability for stainless steel (316 SS). The optimal WO3/BiVO4/NiO photoanode (WB2N2) exhibited 35.1% and 26.6% increase in energy storage capacity compared with WO3 and WO3/BiVO4 under illumination, respectively. The open-circuit potential (OCP) of 316SS coupled with irradiated WB2N2 was reduced from -143 mV (uncoupled OCP) to -726 mV, and the electrode potential can maintain at -540 mV after light was turned off. It was calculated that electrons of about 1.286×10-2C was transferred from WB2N2 to 316 SS after 50s illumination, which was 11.7 and 5.1 times of that WO3 and WB2 passed to 316SS, respectively, confirming the best persistent PCP performance of WB2N2 in the absence of light. The positive role of NiO on the PCP and persistent PCP performance was analyzed. The long-term OCP test and XRD analysis proved the stability of WO3/BiVO4/NiO in PCP performance and chemical composition.

Carbon coated iron pyrite (C–FeS2) photo-electrode for photo-electrochemical water splitting

In this paper, we present fabrication of ‘FeS2’ and carbon coated FeS2 (C–FeS2) photo-electrodes and demonstrated that coating of carbon on FeS2 significantly enhanced photo-electrochemical properties. The hydrothermal method has been adopted for the synthesis of FeS2 and carbon coating on FeS2 was achieved by CVD technique. The materials are subsequently characterized using X-ray diffraction, Raman spectroscopy and Field enhanced scanning electron microscope (FESEM) techniques for phase identification and morphological studies, respectively. The photo-electrochemical measurements revealed significant enhancement in the current density from ∼2 to 3.7 mA/cm2 (∼1.8 times higher) for C–FeS2 in comparison to the FeS2 photo-electrode under visible light. The enhancement in FeS2 after carbon coating has been attributed to reduction in recombination of photo generated charge carriers, enhancement in the band bending and lowering the charge transfer resistance at the semiconductor/electrolyte interface. To date, very few studies have been reported on FeS2 based composites for water splitting applications and use of carbon coating can be a novel approach for developing efficient solar to hydrogen conversion devices. The mechanism for the photocurrent enhancement was supported by Mott-Schottky and electrochemical impedance spectroscopy measurements.

Photoelectrochemical properties of doped TiO2 nanowires grown by seed-assisted thermal oxidation

AbstractTitanium dioxide Nanowires (NWs) are particularly interesting because of their very high surface/volume ratio and their photocatalytic activity allows them to be used in a myriad of applications. This manuscript presents a study of nanowires grown on a conductive substrate making use of a seed-assisted thermal oxidation process. To obtain doped NWs, before the oxidation, metallic titanium was doped with Fe (or Cr) by ion implantation technology. Analyses showed good quality Rutile phase and light absorption in the visible range. Transport properties of the NWs/electrolyte junction were investigated by using linear sweep voltammetry and electrochemical impedance spectroscopy. They allowed us to measure the photovoltage and the barrier height of the junction. We also evaluated the density of hole trap states at the interface during illumination. Electrical results indicate that the formation of deep levels, induced by doping, influences the electron concentration in the TiO2 and the transport properties. Graphical abstract

Interfacial Design of Particulate Photocatalyst Materials for Green Hydrogen Production.

Green hydrogen production using particulate photocatalyst materials has attracted much attention in recent years because this process could potentially lead to inexpensive and scalable solar-to-chemical energy conversion systems. Although the development of efficient particulate photocatalysts enabling one-step overall water splitting (OWS) with solar-to-hydrogen efficiencies in excess of 10% remains challenging, promising photocatalyst candidates exhibiting OWS activity have been demonstrated. This review provides a comprehensive introduction to the solar-to-hydrogen energy conversion process of semiconductor photocatalyst materials and highlights recent advances in photocatalytic OWS via both one-step and two-step photoexcitation processes. The review also covers recent developments in the photocatalytic OWS of SrTiO3, including the establishment of large-scale photocatalytic systems, interfacial design using cocatalysts to enhance water splitting activity, and its photoelectrochemical (PEC) properties at the electrified solid/liquid interface. In addition, there is a special focus on visible-light-absorbing oxynitride and oxysulfide particulate photocatalysts with absorption edges near 600 nm. Methods for photocatalyst preparation and surface modification, as well as PEC properties, are also discussed. The semiconductor properties of particulate photocatalysts obtained from photoelectroanalytical evaluations using particulate photoelectrodes are evaluated. This review is intended to provide guidelines for the future development of particulate photocatalysts capable of efficient and stable OWS.

Photoelectrochemical properties of self-powered corundum-structured Ga2O3 nanorod array/fluorine-doped SnO2 photodetectors modulated by precursor concentrations

Herein, corundum-structured Ga2O3 (α-Ga2O3) nanorod array/fluorine-doped SnO2 (FTO) structures have been fabricated by hydrothermal and thermal annealing processes with different precursor concentrations from 0.01 to 0.06 M. The diameter and length of the nanorod arrays are much larger with increasing precursor concentrations due to more nucleation sites and precursor ions participating in the reaction procedures. The optical bandgap decreases from 4.75 to 4.47 eV because of the tensile stress relieving with increasing the precursor concentrations. Based on self-powered photoelectrochemical (PEC) photodetectors, the peak responsivity is improved from ∼0.33 mA W−1 for 0.06 M to ∼1.51 mA W−1 for 0.02 M. Schottky junctions can be formed in PEC cells. More photogenerated carriers can be produced in wider depletion region. From Mott–Schottky plots, the depletion regions become much wider with decreasing the precursor concentrations. Therefore, the enhance responsivity is owing to the wider depletion regions. Due to the reduced possibility of photogenerated holes captured by traps ascribed from fewer green and yellow luminescence defects, smaller charge transfer resistance, and shorter transportation route, the decay time becomes much faster through decreasing the precursor concentrations. Compared with the other self-powered α-Ga2O3-nanorod-array-based PEC photodetectors, it shows the fastest response time (decay time of 0.005 s/0.026 s) simply modulated by precursor concentrations for the first time without employing complex precursors, seed layers or special device designs. Compared with other high-responsivity monoclinic Ga2O3 (β-Ga2O3) self-powered photodetectors, our devices also show comparable response speed with simple control and design. This work provides the realization of fast-speed self-powered Ga2O3 based solar-blind ultraviolet photodetectors by simple modulation processes and design, which is a significant guidance for their applications in warnings, imaging, computing, communication and logic circuit, in the future.

C3N5 nanosheets decorated with Cu–Pt alloy nanoparticles toward efficient photocatalytic hydrogen evolution

The construction of highly efficient photocatalysts for generating high-purity hydrogen (H2) through a sustainable water decomposition system is a feasible option to replace conventional non-renewable energy resources. Here, we report a simple chemical reduction approach to embed Cu–Pt alloy nanocrystals on the C3N5 (CN) matrix, creating a Schottky heterojunction. The structural morphology, crystal phase, light-harvesting capacity, and photo-electrochemical properties of as-prepared heterostructures were investigated. The uniformly anchored Cu–Pt alloy nanocrystals improve the photocatalytic H2 evolution (PHE) activity by promoting the separation and transfer of photogenerated carriers and inhibiting recombination. Meanwhile, the alloyed nanocrystals strengthen the absorption of incident light energy, inducing photothermal energy. This improves the charge carrier separation and promotes the surface reaction kinetics. The PHE performance of as-developed catalysts could be adjusted by optimizing the molar ratio of Cu/Pt ions. Among them, the optimal Cu1Pt3/CN photocatalyst yields a higher PHE performance (672.85 μmol g−1 h−1). Notably, the Cu1Pt3/CN catalyst also reveals an enhanced photocatalytic activity for H2 evolution in natural seawater. The possible PHE mechanism in CuPt/CN heterostructures is discussed toward the role of CuPt alloy deposition in boosting photocatalytic efficiency.

Templated Growth of In2S3 in Ti3C2TX MXene with Enhanced Photocatalytic Properties

The growth of ultrathin semiconductors is advantageous for photocatalysis due to improved photophysical properties and reduced charge recombination. Along these lines, templating the growth of semiconductors in confined spaces can allow control over semiconductor growth while also conferring the properties of the template to provide composite nanomaterial hybrids. Herein, the semiconductor In2S3 is grown in the organically‐modified interlayer space of Ti3C2TX MXene, a versatile 2D material with metallic character and broadband light absorption. The growth of 1–2 nm thick layers of In2S3 in the interlayer of MXene leads to a drastic increase in photocatalytic properties and light‐induced charge generation due to decreased interfacial charge transfer resistance. Interestingly, the hydrothermal conditions of In2S3 growth lead to partial oxidation of Ti3C2TX MXene to form anatase TiO2 nanocrystals, although this effect is strongly limited by increased In2S3 precursors due to passivation of the MXene surface. MXenes serve as effective templates for the confined growth of semiconductors, emphasizing the potential of MXene as a template for 2D material heterostructures. Overall, this work further develops MXene‐based 2D material composites, offering insights into the origins of the enhanced photocatalytic and photoelectrochemical properties, toward improvements in energy production and aqueous phase catalysis.

Marine Colloids Boost Nitrogen Fixation in Trichodesmium erythraeum by Photoelectrophy.

Nitrogen fixation by the diazotrophic cyanobacterium Trichodesmium contributes up to 50% of the bioavailable nitrogen in the ocean. N2 fixation by Trichodesmium is limited by the availability of nutrients, such as iron (Fe) and phosphorus (P). Although colloids are ubiquitous in the ocean, the effects of Fe limitation on nitrogen fixation by marine colloids (MC) and the related mechanisms are largely unexplored. In this study, we found that MC exhibit photoelectrochemical properties that boost nitrogen fixation by photoelectrophy in Trichodesmium erythraeum. MC efficiently promote photosynthesis in T. erythraeum, thus enhancing its growth. Photoexcited electrons from MC are directly transferred to the photosynthetic electron transport chain and contribute to nitrogen fixation and ammonia assimilation. Transcriptomic analysis revealed that MC significantly upregulates genes related to the electron transport chain, photosystem, and photosynthesis, which is consistent with elevated photosynthetic capacities (e.g., Fv/Fm and carboxysomes). As a result, MC increase the N2 fixation rate by 67.5-89.3%. Our findings highlight a proof-of-concept electron transfer pathway by which MC boost nitrogen fixation, broadening our knowledge on the role of ubiquitous colloids in marine nitrogen biogeochemistry.

Tuning the Optical and Photoelectrochemical Properties of Epitaxial BiVO4 by Lattice Strain

State‐of‐the‐art photoelectrodes in highly efficient photoelectrochemical (PEC) systems often comprise multilayer architectures where lattice mismatch‐imposed strain at the interfaces can perturb the material's crystalline lattice and electronic structure. Despite its inevitable presence, understanding of strain effects in semiconductor photoelectrodes is lacking, preventing rational exploitation of strain engineering to improve photoelectrode performance. In this work, we combine X‐ray structural characterization with strain tensor decomposition analysis as well as optical/photocurrent spectroscopic methods to demonstrate how volumetric lattice deformations caused by substrate‐imposed hydrostatic strain impact the optoelectronic and PEC properties of BiVO4. Utilizing single‐crystalline, epitaxial BiVO4/indium tin oxide (ITO)/yttrium‐stabilized zirconia (YSZx, x = 8% and 13% mol Y2O3) photoelectrodes as a model platform, we find that tensile hydrostatic strain that causes volumetric lattice dilation in BiVO4 results in slightly enhanced optical absorption, but it is detrimental to the internal quantum efficiencies in BiVO4. We attribute this to localization of photogenerated charge carriers, thereby leading to poor charge separation in the bulk of BiVO4 and increased recombination losses. Finally, we highlight the beneficial effects of compressive hydrostatic strain on enhancing the internal quantum efficiencies in BiVO4. Our results provide a basis for exploiting epitaxial strain engineering to optimize the performance of multilayer photoelectrodes in PEC systems.

Fabrication of porous biochar supported Bi2MoO6 photocatalyst for efficient degradation of ciprofloxacin in seawater under visible light irradiation: Mechanistic investigation and intermediates analysis

Efficient separation of photocarriers is a critical approach for advancing high-performance photocatalyst systems to effectively remove environmental contaminants. In this investigation, a hydrothermal technique was employed to synthesize composites of Bi2MoO6 and porous biochar derived from banana peels (BPB). The samples underwent various characterization methods to assess their composition, morphology, and photoelectrochemical properties. The BPB/Bi2MoO6 composite exhibited a synergistic adsorption and photocatalytic impact in eliminating the antibiotic ciprofloxacin (CIP) from pure water and seawater. The optimized BPB/Bi2MoO6 sample displayed a significant degradation efficiency of 98.7 % for CIP after 90 min of visible-light exposure in pure water. In artificial seawater, the degradation efficiency for CIP remained high at 93.6 %, which was 12.2 times greater than that of pure Bi2MoO6. The study also explored the impact of various factors such as catalyst dosage, solution pH, and pollutant concentration on the photocatalytic performance of BPB/Bi2MoO6. Moreover, the catalyst exhibited enhanced efficiency in the adsorption-photocatalytic degradation of CIP within a continuous flow reaction system. The enhanced photocatalytic performance was attributed to the composite's exceptional adsorption capacity, enhanced response to visible light, and efficient separation of photoinduced electron-hole pairs. Furthermore, the BPB/Bi2MoO6 photocatalyst displayed good stability and recyclability over five consecutive photodegradation cycles. Radical trapping and electron spin resonance (ESR) experiments verified that the degradation of CIP was mainly driven by •OH and h+ radicals. A thorough investigation employing density functional theory (DFT), radical trapping and ESR tests, and liquid chromatography mass spectrometry (LC-MS) was conducted to elucidate the degradation mechanism and pathways. Furthermore, toxicity assessment software was utilized to illustrate the progressive reduction in toxicity of the intermediate products. In conclusion, this study provides valuable insights into the role of biochar in enhancing the photocatalytic degradation of pollutants and offers guidance for the future development of environmentally friendly photocatalysts.

Work function-tunable graphene/WO3 heterojunctions for high-performance photoelectrochemical cell: UV-treatment effect and defective graphene

Designing hybrid photoelectrodes with graphene capable of efficient charge-carrier transfer and excellent chemical stability is an effective strategy for developing high-performance photoelectrochemical (PEC) cells. However, it remains unclear how the PEC properties are enhanced and how to control the junction properties in graphene/metal oxide heterojunction-based photoelectrodes. Here, we develop a deterministic junction to enhance PEC performance in graphene/tungsten trioxide (WO3)-based photoelectrodes by tuning the work function of graphene. It reveals that the band structure of graphene/WO3 heterojunctions can be modified by ultraviolet (UV) treatment on WO3 thin films. This modification is supported by the observation that a single-layer graphene/UV-treated WO3 photoelectrode exhibits significantly enhanced PEC activities toward the oxygen evolution reaction (OER) (evidenced by features like a threefold increase in photocurrent, an onset potential shift, and improved stability), whereas the single-layer graphene/untreated WO3 electrode demonstrates improved properties for the hydrogen evolution reaction (HER). Additionally, defects in the graphene layer formed during PEC water splitting contribute to high catalytic activities of the graphene/WO3 photoelectrode due to a decrease in the Gibbs free energy for OER and HER. These results emphasize that band structure engineering via work function tuning in graphene/WO3 heterostructures can provide multiple benefits for high PEC performance and long-term stability.

Highly Efficient Photoanodic Material: Utilizing Dihydrolipoic Acid‐Functionalized CuInS2 Quantum Dots in Photoelectrochemical Cells

AbstractCopper indium sulfide quantum dots (CIS QDs) possess the desired optical properties to act as photoanodic material in photoelectrochemical cells, like a high molar absorption coefficient over the entire visible spectrum and long exciton lifetimes. The already reported procedures that utilize photoanodes based on such nanoparticles, however, exploit harsh conditions or utilize non‐scalable, expensive, and low‐yield syntheses. Here, the construction of CIS QDs adsorbed onto TiO2/FTO photoanodes (FTO = fluorine‐doped tin oxide) with a process aimed at avoiding these issues is proposed. In particular, the employment of dihydrolipoic acid as the ligand allows an easy and cost‐effective functionalization. CdS layers are deposited onto the nanoparticles to enhance the photoelectrochemical properties. Full characterization of the steady–state and transient photoelectrochemical properties of the electrodes is performed to gain information on the interfacial dynamics among the different components of the electrode. Maximum IPCEs of the order of 50% and a spectral sensitization extended up to 700 nm are obtained in the optimized conditions.

Synergistic enhancement of photocatalytic efficiency and durability in CoNi-decorated Cu2O/Cu films for superior synthetic dye degradation

The Cu2O/Cu emerges as a promising candidate for photocatalytic application owing to its efficient photon absorption in the visible light spectrum. However, the susceptibility of Cu2O-based photocatalysts to self-decomposition diminishes their effectiveness. This study introduces CoNi as co-catalyst to enhance the durability of Cu2O/Cu photocatalyst. Electrodeposition was employed to decorate the Cu2O/Cu crystal surface with Co, Ni and CoNi. The deposition potential of CoNi was optimized to produce a high-performance photocatalyst. The utilization of CoNi co-catalyst resulted in significant enhancements in photoelectrochemical properties under light irradiation when compared to using a single Co or Ni co-catalyst, suggesting a synergistic effect between Co and Ni within the system. The enhancement is evidenced by a noteworthy increase in the photocurrent of the photocatalyst, rising from 10.24 mA/cm2 to 20.81 mA/cm2. In addition, the decoration of CoNi resulted in a reduction of the charge transfer resistance from 4.2 kΩ to 0.7 kΩ, while simultaneously increasing the electrochemically active surface area of the photocatalyst from 15.49 cm2 to 157.69 cm2. The observed modifications lead to a substantial improvement in the photocatalytic efficiency, resulting in an impressive 88 % degradation of methylene blue, which is 3.4 times higher than achieved in the absence of the co-catalyst. Moreover, there was a significant improvement in the photostability of the photocatalyst, with an increase from 16.81 % to 50.55 %. These findings demonstrate the significance of CoNi co-catalyst decoration in producing a highly active and durable photocatalyst, making it a promising candidate for efficient synthetic dyes degradation.

Heterojunction characteristics and photoelectrochemical performance of TiO2 nanorods sensitized by zeolitic imidazolate framework

Traditional photocatalysts suffer from inferior utilization of solar light. Therefore, developing novel photocatalyst for better solar light harvesting is much required in the wake of current environmental problems arising from conventional energy technologies. Here we report synthesis and characterization of photocatalysts based on TiO2 nanorods (TNR) and Zeolitic Imidazolate Framework-9 (ZIF-9) and their photoelectrochemical properties. The TNRs were sensitized by ZIF-9 through solvothermal method. The presence of ZIF-9 on TNR formed a p-n heterojunction which assisted in initiating efficient charge separation and promoting injection of these carriers into the electrolyte. The heterojunction catalysts also exhibited enhanced optical properties in terms of extended absorption with reduced bandgap in comparison to the TNR film. The aforementioned properties manifested in improved photoelectrochemical performance with a current density of 0.94 mA/cm2, which is four times better than TNR and an applied bias photon to current efficiency (ABPE) of 0.27 %, which is five times better than TNR film alone. These superior properties of the processed ZIF-TNR demonstrate their potential for photoelectrochemical catalysis, thus paving the way for green hydrogen generation.

Investigations of the photoelectrochemical and photo-Fenton properties of TiO2/FeOCl nanocomposites

Investigations of the photoelectrochemical and photo-Fenton properties of TiO2/FeOCl nanocomposites

A closer look at the magnetic, photo-electrochemical, and optical properties of rare earth (Sm, Dy, Ho, Er, and Yb)-doped manganese ferrite for potential use as a photocatalyst

For photocatalysis technology to be applied industrially, there has been a significant increase in the need for visible-light-driven photocatalysts that possess exceptional superparamagnetic characteristics to facilitate easy separation. Hence, in this study, rare earth elements (RE) (Sm, Yb, Dy, Er, and Ho) were systematically doped into manganese ferrite (MF) using the coprecipitation method to serve two purposes, namely, reducing the photogenerated electron-hole recombination during photocatalysis and modifying the magnetic properties of MF to become superparamagnetic. The synthesised Re-doped MF was found to be visible light active, as evidenced by the transient photocurrent response and the obtained band gaps, which were in the range of 1.84–1.93 eV. From the cyclic voltammetry, electrochemical impedance spectroscopy, and Tafel polarization plots, it was evident that different RE element dopants have different effects on improving the electrochemical properties of MF. Overall, fast electron transfer of the synthesised materials was found to decrease in the following order: Sm-MF > Dy-MF > Ho-MF > MF > Er-MF > Yb-MF. The g-factor and peak-to-peak line width were found to be in the range of (2.221–2.317) and (93.17–149.85 mT), respectively. The resonance field and hysteresis loop (Hc) were found to be in the range of (289.2–301.86 mT) and (8.24–32.61 mT), respectively. Overall, the synthesised RE-doped MF exhibits ferromagnetic properties, and the obtained small Hc values hint at these particles exhibiting superparamagnetic properties. In summary, doping MF with Sm, Dy, and Ho is more desirable as it alters the magnetic properties towards superparamagnetic and improves its electrochemical properties. Thus, this study is of importance in advancing the field of photocatalysis in water treatment and material science.

2D MoB MBene: An Efficient Co-Catalyst for Photocatalytic Hydrogen Production under Visible Light.

Highly active and low-cost co-catalysts have a positive effect on the enhancement of solar H2 production. Here, we employ two-dimensional (2D) MBene as a noble-metal-free co-catalyst to boost semiconductor for photocatalytic H2 production. MoB MBene is a 2D nanoboride, which is directly made from MoAlB by a facile hydrothermal etching and manual scraping off process. The as-synthesized MoB MBene with purity >95 wt % is treated by ultrasonic cell pulverization to obtain ultrathin 2D MoB MBene nanosheets (∼0.61 nm) and integrated with CdS via an electrostatic interaction strategy. The CdS/MoB composites exhibit an ultrahigh photocatalytic H2 production activity of 16,892 μmol g-1 h-1 under visible light, surpassing that of pure CdS by an exciting factor of ≈1135%. Theoretical calculations and various measurements account for the high performance in terms of Gibbs free energy, work functions, and photoelectrochemical properties. This work discovers the huge potential of these promising 2D MBene family materials as high-efficiency and low-cost co-catalysts for photocatalytic H2 production.

Novel approach: Simultaneous application of ionic liquid doped polymer electrolyte in supercapacitor and dye-sensitized solar cells

The present study reports the synthesis, characterization, and application as energy devices of an ionic liquid blended polymer electrolyte film in which the host polymer polyvinyl alcohol (PVA) is mixed with low viscosity ionic liquid (IL) 1-ethyl-3-methylimidazolium thiocyanate. Various characterization tools have been used further to elaborate electrical, structural, and photoelectrochemical properties. X-ray diffraction (XRD) and polarized optical microscope (POM) affirm the reduction of crystallinity of polymer, while Fourier transform infrared spectroscopy (FTIR) shows complexation and composite nature. Electrochemical impedance spectroscopy shows an enhancement in ionic conductivity by IL doping, where the highest conductivity is achieved at 60 wt% of IL concentration with a conductivity value of 6.21 × 10⁻⁴ S/cm. The ionic transference number (tion) and electrochemical stability measurement show the film's predominantly ionic nature and a reasonable stability window. Using maximum conducting film sandwiched between electrodes, we have successfully fabricated two devices, i.e., an electrical double-layer capacitor (EDLC) and a dye-sensitized solar cell (DSSC). The fabricated EDLC capacitor shows a specific capacitance of 125 F/g, while DSSC shows an efficiency of 1.1 % at one sun condition.

Facile preparation of ZIF-67 on TiO2 and enhancement photocathodic protection for 316L stainless steel

Photocathodic protection (PCP) anticorrosion using sunlight is a green and sustainable technology. However, the ease of carriers compounding and the low light utilization are still the main restraints to its development. To develop an effective photoanode, a metal-organic framework (MOF, i.e., ZIF-67) material is electrodeposited and grown in-situ on TiO2 nanorods. The morphological structure, light absorption properties, photoelectrochemical properties and cathodic protection principle of ZIF-67/TiO2 photoanode are analysed by SEM, PL, I-V and EIS. The material characterization and light absorption characteristics show that the photoanode has good light absorption performance and higher electron hole separation efficiency. Photoelectrochemical test shows that ZIF-67/TiO2 photoanode has excellent photocathodic protection for 316L stainless steel (316L SS). ZTRs-60 has the optimal protection effect. Under simulated sunlight, the OCP of 316L SS coupled ZTRs-60 is -0.41 V vs. Ag/AgCl, and the current density of the I-t curve can reach 20 μA/cm2. EIS and Tafel tests show that the photogenerated electrons transfer to the stainless steel surface, which promotes the cathode polarization process and alleviates the metal corrosion.

Low-crystallinity porous Ni2P2O7 nanowires with excellent CO2 capture ability for highly-efficient CO2 reduction

In this study, we prepared the porous Ni2P2O7 nanowires with low-crystallinity (LC-NPO) and high-crystallinity Ni2P2O7 nanosheets (HC-NPO), and employed them for the first time as catalyst in the CO2 photoreduction reaction. The photocatalytic performance of them was tested under the UV–Vis light irradiation and compared with the TiO2 commercial powder (P25). The CO2 photoreduction experiments shown that the LC-NPO had the highest ability than the HCNPO and the P25. Specifically, with triethanolamine (TEOA) as the sacrificial agent, LC-NPO achieved CO and CH4 yields of approximately 56.06 and 12.13 μmol·g−1 after 4 h UV–Vis light irradiation, which were 4.67 and 5.00 times of P25, respectively. The experimental results, and Density Functional Theory calculations proved that the unique porous nanowire structure enables LC-NPO to have a larger specific surface area, higher quantity of oxygen defects, and superior CO2 capture ability compared to HC-NPO. These features maybe the primary reasons for the excellent CO2 photoreduction ability. Besides, the photo-electrochemical characterizations revealed that the LC-NPO had the much superior photoelectrochemical properties than the HC-NPO, which was another reason for enhanced photocatalytic ability. In-situ FTIR and 13C isotope labeling experiments were used to monitor the CO2 reduction process, and finally a potential enhanced mechanism had been discussed.