Phased Array Ultrasonic Method Research Articles

Phased Array Ultrasonic Method for Robotic Preload Measurement in Offshore Wind Turbine Bolted Connections.

This paper presents a novel approach for preload measurement of bolted connections, specifically tailored for offshore wind applications. The proposed method combines robotics, Phased Array Ultrasonic Testing (PAUT), nonlinear acoustoelasticity, and Finite Element Analysis (FEA). Acceptable defects, below a pre-defined size, are shown to have an impact on preload measurement, and therefore conducting simultaneous defect detection and preload measurement is discussed in this paper. The study demonstrates that even slight changes in the orientation of the ultrasonic transducer, the non-automated approach, can introduce a significant error of up to 140 MPa in bolt stress measurement and therefore a robotic approach is employed to achieve consistent and accurate measurements. Additionally, the study emphasises the significance of considering average preload for comparison with ultrasonic data, which is achieved through FEA simulations. The advantages of the proposed robotic PAUT method over single-element approaches are discussed, including the incorporation of nonlinearity, simultaneous defect detection and stress measurement, hardware and software adaptability, and notably, a substantial improvement in measurement accuracy. Based on the findings, the paper strongly recommends the adoption of the robotic PAUT approach for preload measurement, whilst acknowledging the required investment in hardware, software, and skilled personnel.

Spatial and directional characterization of wire and arc additive manufactured aluminum alloy using phased array ultrasonic backscattering method

Pores, grains, or textures can collectively cause microstructural inhomogeneity and anisotropy in metallic materials fabricated by additive manufacturing. In this study, a phased array ultrasonic method is developed to characterize the inhomogeneity and anisotropy of wire and arc additively manufactured components by performing both beams focusing and steering. Two backscattering features, i.e., the integrated backscattering intensity and the root mean square of the backscattering signals, are employed to quantify the microstructural inhomogeneity and anisotropy, respectively. An experimental investigation is performed using an aluminum sample fabricated by wire and arc additive manufacturing. The ultrasonic measurements, performed on wire and arc additive manufactured 2319 aluminum alloy, show that the sample is inhomogeneous and weakly anisotropic. Metallography, electron backscatter diffraction, and X-ray computed tomography are used to verify the ultrasonic results. An ultrasonic scattering model is used to identify the influence of grains on the backscattering coefficient. Compared with a wrought aluminum alloy, the complex microstructure in additively manufactured material significantly influence the backscattering coefficient, and the presence of pores cannot be neglected in ultrasonic-based nondestructive evaluation for wire and arc additive manufactured metals.

Ultrasonic fingerprinting by phased array transducer

Increasing quantity of spent nuclear fuel that must be under national and international control requires a novel approach to safeguard techniques and equipment. One of the proposed approaches is utilize intrinsic features of casks with spent fuel. In this article an application of a phased array ultrasonic method is considered. This study describes an experimental results on ultrasonic fingerprinting of austenitic steel seam weld.

Identification of Lack of Fusion and Penetration in Circumferential Fillet Weld by Phased Array Ultrasonic Method in Gas Industry

The article deals with non-destructive ultrasonic identification of lack of fusion and penetration in circumferential fillet welds in gas industry by using Phased Array method. These types of welds are used mainly for repairs of gas pipelines during operation. The main aim of this paper is to compare results of measurements of the weld with and without defect. Phased Array testing procedures for circumferential fillet welds methods are also described in this article.

Defect Detection in Pipelines during Operation Using Magnetic Flux Leakage and Phased Array Ultrasonic Method

The present article is focused on the non-destructive testing (NDT) inspection of pipelines during operation namely Magnetic Flux Leakage (MFL) method and Phased Array ultrasonic (PA) method. MFL inspection technique is electromagnetic test method primarily used to detect flaws or defects in high-permeability of ferromagnetic metals such as carbon steel tubing, plate, wire rope and tubular parts. PA ultrasonic method is an advanced NDT method that is used to detect component failures i.e. cracks or flaws and thereby determine component quality. Due to the possibility to control parameters such as beam angle and focal distance, this method is very efficient regarding to the defect detection and speed of testing. In this article real pipeline defect was identified by MFL method in the internal pipe inspection. This defect was fully mapped by Phased Array ultrasonic method in the terrain. 3D model of defect in the tested material was created from measured data and obtained by PA method. The real dimensions of the defect determined from measurements by the method of MFL and PA are compared.

Embedded Non-destructive Evaluation for Structural Health Monitoring, Damage Detection, and Failure Prevention

In this paper we review the state of the art in an emerging new technology: embedded ultrasonic non-destructive evaluation (NDE). Embedded ultrasonic NDE permits active structural health monitoring, i.e. the on-demand interrogation of the structure to determine its current state of structural health. The enabling element of embedded ultrasonic NDE is the piezoelectric wafer active sensor (PWAS). We begin by reviewing the guided wave theory in plate, tube, and shell structures, with special attention to Lamb waves. The mechanisms of Lamb wave excitation and detection with embeddable PWAS transducers is presented. It is shown analytically and verified experimentally that Lamb wave mode tuning can be achieved by the judicious combination of PWAS dimensions, frequency value, and Lamb mode characteristics. Subsequently, we address in turn the use of pitch-catch, pulse-echo, and phased array ultrasonic methods for Lambwave damage detection. In each case, the conventional ultrasonic NDE results are contrasted with embedded NDE results. Detection of cracks, disbonds, delaminations, and diffuse damage in metallic and composite structures are exemplified. Other techniques, such as the time reversal method and the migration technique, are also presented. The paper ends with conclusions and suggestions for further work.

Analysis of Creep Crack Growth by Intelligent Phased Array Ultrasonic Inspection

At high temperatures typical for service conditions in fossil power plants, the creep fracture is dominated by the formation, growth and coalescence of cavities. Using high temperature pipe materials, P92 and P122, the characteristics of creep crack growth were analyzed in this study according to the cavities. The characteristics of cavities play a critical role in creep crack propagation and load line displacement. The effect of the load line displacement rate(dv/dt) and crack growth rate(da/dt) on the da/dt–Ct relation of creep crack growth was evaluated at different temperatures and Ki(initial stress intensity factor) values. The number of cavities increased with increasing temperature and Ki. The crack growth rate and load line displacement rate increased with the increase in the cavity numbers. The kind and distribution of these internal flaws were investigated by an intelligent phased array ultrasonic method and they were utilized in deriving the relationship with the creep crack growth rate, which will predict the creep characteristics of these materials.