Melting Temperature Of Phase Change Material Research Articles

Preparation and Performance of Inorganic Hydrated Salt-Based Composite Materials for Temperature and Humidity Regulation

In this work, it was first proposed to combine hydrated salt phase change materials (PCMs) with humidity control materials to prepare the temperature and humidity control material. The composite PCM was prepared by absorbing Na2HPO4·12H2O with colloidal silicon dioxide, and diatomite was selected as the humidity control material. The humidity performance tests found that diatomite had good moisture absorption/desorption capacity and excellent moisture buffering capacity. The supercooling degree tests showed that Na2SiO3·9H2O as nucleating agent effectively reduced the supercooling degree, and the addition of deionized water improved the water loss problem of composite PCMs. The DSC tests showed that the enthalpy and melting temperature of composite PCMs were 153.1 J/g and 28.9°C, respectively. By placing the temperature and humidity control material in different humidity, it was found that the moisture content of diatomite affected the thermal properties of composite PCMs. Diatomite could not only transfer moisture to hydrated salts but also absorb moisture from hydrated salt. The application performance tests of the temperature and humidity control material in the room model showed that it could simultaneously regulate indoor temperature and humidity. Overall, this temperature and humidity control material was more suitable for environments with high relative humidity such as greenhouses.

Temporal numerical analysis of beeswax PCM melting in a cube geometry subjected to a constant wall temperature condition

The ability of phase change materials (PCM) to store thermal energy has gained wide application area, like battery thermal management, solar water desalination and many other. The melting process of beeswax phase change material within the cube geometry with constant wall temperature (65 °C) boundary condition has been investigated using solidification and melting model. The fluid flow and heat transfer governing equations are solved using second order finite volume scheme. A PRESTO algorithm is applied for pressure-velocity coupling. The convergence criteria of 10−10 have been selected for energy equation, while 10−8 is selected for both momentum and continuity equations. The results like percentage variation along length-height and height-width plane for transient liquid fraction and temperature has been plotted, along with velocity streamlines within the cube geometry. From the obtained results it is concluded that the melting fraction and temperature of beeswax PCM is different in different planes and the major factors which affect the complete melting process is wall temperature, and the geometry. A difference of more than 0.1 °C in temperature has been recorded between mid-length-height and height-width plane while a difference of more than 2% in liquid fraction of PCM is observed. Even the uniformity of temperature and liquid fraction is notably influenced and vary along length, height, and width of cube geometry. Thus, it is concluded that melting process of PCM may affect the ability to store and release the heat energy which further affect the performance parameters of applied physical system.

Investigation of numerical phase transition of nano-enhanced SiC/paraffin wax PCM in solar-assisted water desalination system

Adding nanoparticles in phase change material (PCM) is a new trend for enhancing their thermal energy-storing ability as well as thermal conductivity. From this point of view, a numerical study is carried out to examine the addition of silicon carbide nanoparticles in paraffin wax PCM, used as heat energy storing material in a semi-cylindrical solar water desalination system. The PCM temperature is maintained at 52 °C and the semi-cylindrical tubular section has a wall temperature of 85 °C. The top plane section of the tubular solar collector is made up of graphite material. A semi-circular cross-section is selected for numerical analysis. A finite volume solver is used for solving thermal and fluid flow governing equations. A pressure staggering option algorithm is applied for pressure–velocity coupling. The temporal parameters like temperature, velocity contours, melting fraction, enthalpy, and entropy of nano silicon embedded paraffin wax PCM are widely discussed. The results clearly show that the phase transition of solid PCM to fluid PCM is greatly influenced by nanoparticle addition and enhances the rate of heat transfer. Initially for the first 60 min the melting fraction and temperature of PCM remain uniform as the time step increases above 60 min the behavior of PCM changes abruptly which clearly indicates the random distribution of nanoparticles within the PCM. A critical time and temperature limit exists for nanoparticles-based PCM beyond which, the thermal efficiency of the solar water desalination system gets influenced.

The Modification of Thermal Conductivity of Phase Change Material Using Nano Metal-Oxide Particles

The phase change materials (PCM) based cooling system have gained recent popularity with PV module temperature (TPV) reduction. PCM is an effective thermal energy storage material with the activation of latent heat capacity. Its low heat conductivity has been discovered in several studies. In this study, PCM is chosen to mix with nanoparticles to enhance its thermal conductivity and performance. For an ambient temperature of 38, it is suggested that the melting temperature (Tmelt) of PCM should be between 41 and 44 °C. Nanoparticle composited PCM (nc-PCM) are generated by mixing lauric acid (LA) with three different types of nanoparticles, including aluminum oxide (Al2O3), copper oxide (CuO), and magnesium oxide (MgO) in the following proportions: 100:0, 99:1, 98:2, 94:6, 92:8 and 90:10. It has been shown that the melting points (Tmelt) of the studied nc-PCMs are between 41.18 and 42.47 °C and thermal conductivity increases. According to the findings, the best balance between latent heat of fusion and thermal conductivity should be at 6% nanoparticle. Finally, it is expected that employing these three nc-PCM to reduce the PV module's temperature will enhance PV efficiency.

Effects of Superabsorbent Polymer Addition on the Thermal Properties of Eutectic Phase Change Material

In this study, the influence of a super absorbent polymer (SAP) addition on the thermal properties of phase change material (PCM) was investigated. It was found that adding SAP reduced the melting temperature of PCM and improved phase separation properties. While the addition of 1.0 wt% of SAP to PCMs decreased latent heat by 3 J/g to 24.4 J/g, the addition was determined to be necessary to prevent leaks from a functional duct unit (FDU) and assure product stability. The results obtained from a series of brine refrigeration tests indicate that the supercooling temperature decreased by 0.3 °C to 1.7 °C when 1.0 wt% of SAP was added to PCM. The addition of SAP to PCM appears to promote supercooling by encouraging condensation during phase change. As a result of applying SAP-added PCM to the FDU, the isothermal operation performance was improved compared to existing refrigerators.

Enhanced performance of photovoltaic thermal module and solar thermal flat plate collector connected in series through integration with phase change materials: A comparative study

The decline in photovoltaic cell efficiency due to temperature elevation, coupled with solar energy's inherent intermittency, presents challenges for solar systems, including photovoltaic panels and solar thermal (ST) collectors. The integration of phase change materials (PCMs) emerges as a promising solution to enhance thermal energy storage and regulation, thereby improving system performance and sustainability. This study investigates the performance of series-connected photovoltaic thermal (PVT) and ST systems with integrated PCMs from energy and exergy viewpoints, utilizing a 3D transient numerical simulation. The proposed system's performance is compared with that lacking a PCM across various heat transfer fluid mass flow rates. Suitable PCM selection based on melting temperature is explored, along with PCM layer thickness and nanoparticle augmentation. The research highlights that PCM integration effectively regulates PV cell temperature, enhancing electrical power and exergy rate. While increasing the mass flow rate improves thermal and electrical power, it reduces the thermal exergy rate. Comparing different PCMs (RT28 HC, RT35 HC, and RT44 HC), the RT28 HC PCM provides the lowest temperature of PV cells and the best electrical performance during the day. Moreover, increasing PCM layer thickness results in lowering PV cell and outlet temperatures and storing more heat. Nanoparticles added to PCMs lead to a marginal improvement in energy and exergy, especially for the system with RT28 HC. This analysis emphasizes PCM integration's role in enhancing solar thermal system performance, highlighting the importance of considering the PCM's melting temperature for effective thermal energy management.

Optimization of Building integrated photovoltaic and thermoelectric hybrid energy harvesting system for different climatic regions

As energy saving emerges as a critical factor for the sustainable development of humankind, the importance of Zero-Energy Buildings (ZEB) is gradually increasing. Therefore, much research is being conducted on high-efficiency renewable energy technologies that can be applied in urban areas. However, increasing the efficiency of BIPV were proposed and studied because of the need for the renewable energy source. Such as using phase change material (PCM), heat fin, wavelength selection, PV surface temperature decreasing or using a thermoelectric generator (TEG), and convection cooling utilizing the waste heat from the PV. In most previous studies, the performance when each method was analyzed through experiments or simulations. However, the design analysis for maximum performance still needs to be conducted. Therefore, a BIPV combined with a PCM and TEG (BIPV-TEG-PCM) design is analyzed in this study. Herein, the three variables (phase change temperature of the PCM, heat fin spacing in the PCM container, and TEG arrangement) were analyzed through computational fluid dynamics (CFD)-based simulations. Moreover, through multi-objective optimization, the BIPV-TEG-PCM system of the optimal design was derived. Analysis results of the appropriate melting temperature of PCM, heat fin interval, and arrangement of TEG for the proposed system are 40 °C, 12.4 mm, and 187 mm, respectively.

Energy storage potential analysis of phase change material (PCM) energy storage units based on tunnel lining ground heat exchangers

Low geo-temperature geothermal energy in the surrounding rock can be extracted by tunnel lining ground heat exchangers (GHEs) and stored in phase change material (PCM) plates to realize the cold energy utilization. However, the research of the coupling heat transfer of tunnel lining GHEs and PCM plates has been rarely reported. In this study, a 3D coupling heat transfer model of tunnel lining GHEs and PCM plates was developed to investigate the cold energy storage performances of PCM plates under different PCM and tunnel parameters. The circulative iteration calculation is used to solve the coupling model. The results show that the cold energy storage of PCM plates utilizing tunnel lining GHEs for energy storage is feasible. The PCM melt fraction and solid phase PCM proportion within the PCM plates decrease and increase respectively with an increase in the PCM thermal conductivity and melting temperature and a reduction in the surrounding rock temperature. The cold energy storage efficiencies of PCM plates improve by 77.8% and 34.1% as the PCM thermal conductivity and melting temperature increase by 1 W/(m K) and 4 ℃. Moreover, the cold energy storage efficiency of PCM plate enhances by 68.5% as the surrounding rock temperature reduces from 10 to 1 ℃. A larger difference between the surrounding rock temperature and PCM melting temperature is efficient for the cold energy storage of PCM plates, and the cold energy storage time and temperature difference show a power function relationship. Finally, increasing the tunnel lining GHEs length is conducive to enhancing the cold energy storage efficiency of PCM plates, whereas this enhancement is limited. In actual applications, selecting a reasonable tunnel lining GHEs length is necessary.

Energy performance based optimization of building envelope containing PCM combined with insulation considering various configurations

Phase change material (PCM) is considered as a promising solution for reducing heating and cooling energy consumption by integrating them into the building envelope, which in turn reduces CO2 emissions. In this paper numerical simulations were carried out to evaluate the energy performance based optimization of envelope building integrated PCM. The effect of several parameters (PCM melting temperature, PCM layer combined with insulation, PCM layer and insulation layer thickness, double PCM layer system in the double external wall, and air layer interaction with PCM in roof) on energy savings in two typical models of residential buildings in Tunisia are investigated. Results show that energy demand reduction of 73.81% and 76.46% can be achieved under the optimal conditions of application of the PCM integrated in simple wall and double wall buildings respectively. This is associated with significant reduction of CO2 emission. Moreover, PCM layer performance is improved by increasing its thickness with an optimal value of 6 cm. Two PCM layers located in the middle of the double wall involve higher energy saving than a simple PCM layer.

Experimental and numerical investigation of PCMS on ceilings for thermal management

In this study, experimental investigation of phase change materials (PCM) integrated into building on ceilings was assessed for thermal management capabilities by comparing two building test models with and without PCM based on fluctuation in PCM temperatures owing to ambient temperature variations. Commercial organic PCM (OM-30) with a peak melting point of 31.10 C was used as PCM with high-density polyethylene (HDPE) as the encapsulation. Differential scanning calorimeter (DSC) was used to examine the thermophysical characteristics of PCM such as phase transition temperature, latent heat, and specific heat capacity. The various PCM temperature ranges included for the study are (i) Above phase change melting temperature range ii) within Phase Change melting temperature range iii) Proximity to PCM onset melting temperature range iv) proximity to PCM end melting temperature range. Under free-floating ambient Condition, the indoor air temperature was dropped in PCM installed room up to 1.69 °C, 5.79 °C, 2.26 °C, & − 2.87 °C compared to without PCM room for a PCM Melting temperature difference of 8.77 °C,1.55 °C, 1 °C & 0.44 °C respectively. Also, it was divulged that the PCM utilized 3.2%, 31.4%, 6.9%, & 12.27% of the total latent heat energy deployed in order to produce a temperature difference of 1.69 °C, 5.79 °C, 2.26 °C, & − 2.87 °C compared to without PCM room.

Thermal performance enhancement methods of phase change materials for thermal energy storage systems – A review

Phase Change Materials (PCMs) have emerged as a promising solution for efficient thermal energy storage and utilization in various applications. This research paper presents a comprehensive overview of PCM technology, including its fundamental working principles, classification and different shapes of container used for PCM storage. The study investigates the optimal melting temperature of PCMs and explores various Thermal Energy Storage (TES) methods and their types. This paper discusses novel approaches to enhance the thermal performance of PCMs, such as incorporating high-conductivity materials, Nano-encapsulation, Composite formation, and Shape stabilization. These innovative techniques have shown great potential in enhancing efficiency of PCM-based TES systems. The information presented in this paper is an in-depth analysis of research papers published over the last five years (2019 to 2023). It is a valuable source for researchers seeking to stay current with the modern advancements in PCM technology and its applications. This research contributes to advancing sustainable and efficient thermal energy utilization by promoting a deeper understanding of PCM's capabilities and challenges.

Introduction of sustainable food waste-derived biochar for phase change material assembly to enhance energy storage capacity and enable circular economy

Production and utilization of renewable materials receive considerable attention to achieve the goals of carbon neutrality and carbon peaking and create a sustainable society. Phase-change materials (PCMs) have emerged as a novel energy storage technology but usually suffer inherent insufficient thermal stability and liquid leakage, thereby requiring solid supporting materials. However, there are complications in the synthesis of PCM-supporting materials, including environmental issues. In this regard, upcycling biowaste into higher value carbon materials, inspired by the low cost and availability of feedstocks, is a promising strategy for dealing with challenges caused by waste and global climate change. Thus, we designed food waste-derived biochar-supported PCMs using a facile vacuum impregnation method to overcome these limitations. Porous biochar materials with a certain degree of graphitization, high specific surface area (SSA), (up to 1195 m2 g−1), and micro-/mesopore distribution were prepared from sustainable and commercially available food waste through carbonization and activation. They displayed greater carbon lattice expansion after undergoing KOH activation and being washed than that shown by carbon materials synthesized without activation. Thereby, the graphitic carbon materials presented high loading ratios and corresponding enthalpy values that were 243.9, 302, 346.9, and 251.4 % higher than those of the composites prepared without activation, encapsulated only 15 wt% of octadecane. Additionally, the composite PCMs exhibited high thermal stability without leakage above the melting temperature of pristine PCM. Textural properties, including the SSA, interconnected pores, activation, graphite-like characteristics, and intermolecular interactions between the composite constituents, were integral to the enhanced thermal performance of the as-synthesized composite PCMs. Furthermore, the composite demonstrated high durability, showing potential for thermal management, sustainable management of food waste, and mitigation of climate change.

Low-energy resilient cooling through geothermal heat dissipation and latent heat storage

Conventional passive cooling techniques provide limited benefits in extremely hot climates in southern Asia, characterised by high daytime and night temperatures and frequent climate-related disruptions, such as power cuts. This study proposes and demonstrates a novel low-energy and resilient cooling solution for extremely hot regions in southern Asia. The novelty lies in the combination of geothermal heat dissipation and latent heat storage, specifically designed for the particular conditions of extremely hot climates in Southern Asia; considering the influence of climate-related disruptions such as power cuts, whose frequency is increasing in the region; and using discomfort hours as an indicator to measure the passive survivability of buildings in the absence of air-conditioning (following the adaptive comfort model). A numerical model was developed in TRNSYS for optimal sizing and configuration of the phase change material (PCM) integrated into a ceiling panel using a typical multi-family building archetype in three climatic regions of Pakistan. A parametric numerical analysis was performed concerning different PCM melting temperatures, amount of PCM, convective heat transfer capacity, and equivalent thermal conductivity. Moreover, daytime was considered the period with a higher probability of power cuts. The results showed how integrating PCM-based ceiling panels with geothermal heat dissipation can mitigate discomfort hours by 28 % in extremely hot climates, 55 % in very hot climates, and 91 % in hot climate areas with intermittent access to electricity. Latent heat storage maximised the benefits of geothermal heat dissipation by extending thermal comfort periods by 13 % and 18 % in extremely hot and very hot climates compared to the scenario without PCM. This low-energy resilient cooling solution, integrating PCM as a cool battery, can keep the home cool for longer when electricity is unavailable. This study demonstrates the importance of considering the specific climate-related disruptions from these extremely hot regions in building design, such as extreme heat events or power cuts, to enhance the heat resilience capacity of cities.

Numerical investigation of melting process for phase change material (PCM) embedded in metal foam structures with Kelvin cells at pore scale level

The present numerical study analyzes the melting process of phase change material (PCM) embedded in a metallic foam structure at pore scale level. The computational domain consists of two different sizes of 3D cubic boxes. The analyzed domain is filled with Kelvin cell-structures with different Cell Per Length (CPL) and constant porosity of 0.956. A constant temperature, higher than the melting temperature of PCM, is assigned to one external surface of the enclosure, while the other surfaces are adiabatic. The conjugate problem for the heat transfer between the PCM and the solid structure with Kelvin cells is developed. Enthalpy-porosity method is used to describe the PCM melting process. The finite volume method is used to solve the conjugate heat transfer problem at pore scale level by Ansys-Fluent code. A comparison of different CPL values is reported in terms of liquid fraction, average temperature of the PCM, and energy storage. The comparison is also considered between the two different volumes of the cubic boxes. The presence of the metallic structured Kelvin cells increases the overall heat transfer rate and decreases the melting time. Results for smaller cavity indicates that as the CPL number increases, the time required for the PCM melting process decreases. Furthermore, the total heat accumulation process takes a shorter time to reach the maximum value. The melting time and the duration of heat accumulation are worsened for the large cubic box (L = 4 inch) at CLP>6. This is due to the dominant viscous effect, which decreases the velocity induced by the buoyancy forces because of higher contact surface area. In these cases, heat transfer between liquid and solid phases of the PCM decreases substantially.

Thermo-fluid performance enhancement in a long double-tube latent heat thermal energy storage system

Thermodynamic analysis and flow rate optimization for the long double-tube latent heat thermal energy storage systems (LHTESS) are performed. Computer modeling is carried out using created software and is based on a developed 3D non-steady non-linear coupled thermo-fluid mathematical model that combines the apparent heat capacity method and finite volume method for the sodium nitrate (NaNO3) phase change materials (PCM) and for the Syltherm800 heat transfer fluid (HTF). The mathematical model and numerical algorithm are verified through comparison with experimental data. It is found that the laminar flow of HTF ensures the uniform temperature in PCM and in HTF and this temperature is equal to the PCM melting temperature. It is proved that the PCM and HTF average temperatures along the LHTESS can be equalized using spatial and temporal velocity variations of the HTF. Mutual impact of the heat transfer and fluid mechanics parameters in the long double-tube LHTESS was studied by correlation between Nusselt numbers and Reynolds numbers. The optimal HTF flow rate parameters were analyzed based on the non-equilibrium thermodynamics method. It is discovered that the laminar regime 0 < Re < 2000 and the turbulent regime 12000<Re<15000 are the most optimal for long double-tube LHTESS of the described geometry.

Energy exergy and economic evaluation of a CCHP configuration powered by CPVT collectors dynamically

This study presents a dynamic simulation of a combined cooling, heating, and power (CCHP) configuration powered by concentrating photovoltaic thermal (CPVT) collectors. The desired configuration comprises CPVT collectors, a phase change material (PCM) storage tank, an organic Rankine cycle (ORC), an absorption chiller, and heat exchangers. The evaluation has been carried out for a residential building using EES, MATLAB, and TRNSYS software. Moreover, an auxiliary heater has been used to provide the thermal energy of the desired configuration in case of low or no solar irradiation. The desired configuration has been evaluated from energy, exergy, and economic points of view during the warm months of the year (May to September). Also, the influences of key parameters of the desired system such as the CPVT area, CPVT flow rate, and PCM melting temperature on the performance of the desired configuration have been examined. The results indicate that the solar fraction enhances by about 161 % when the CPVT area changes from 100 m2 to 400 m2. Also, CPVT has found to be the main contributor to exergy destruction, accounting for 49% of the total. The maximum energy and exergy efficiencies of the desired configuration are obtained at the CPVT area of 400 m2 with values of 72.26 % and 79.03 % respectively. On the other hand, the lowest payback period occurs at 100 m2 with value of 11 years.

Annual Thermal Management of the Photovoltaic Module to Enhance Electrical Power and Efficiency Using Heat Batteries

Several studies state that phase change material (PCM) improves the electrical power and efficiency of the photovoltaic (PV) module. To find the suitable PCM for tropical climatic conditions, multi-PCMs are examined simultaneously with melting temperatures of 31 °C, 35 °C, 37 °C, and 42 °C. In this study, PCM containers are integrated behind the PV module with a thickness of 50 mm. The performance of the multi PV-PCMs is monitored year-round and compared with PV-noPCM. The experimental results show that the selected four PCMs performed the cooling process autonomously in all the climates, such as PCM with a melting temperature of 37 °C and 42 °C enhanced the higher cooling rate in summer, and the same PCMs failed to achieve a higher cooling rate in winter. The lowest temperature drop was noted for pre-monsoon and monsoon seasons due to the low irradiance. On the other hand, the highest temperature drop of 16.33 °C is observed for pre-summer (March) and 15.7 °C, and 17.14 °C for summer (April) as compared to PV-noPCM. The results of the present investigation highlight the requirement for choosing the proper PCM melting temperature based on optimal year-round performance. Further, it is recommended that a single PCM melting temperature for cooling the PV modules year-round in tropical climates is inappropriate, and instead, a cascaded structure with different PCM melting temperatures is recommended.

Numerical study on latent heat thermal energy storage with phase change material and metal foam in shell and corrugated tube with external heat losses

In the present work, a numerical investigation of the Latent Heat Thermal Energy Storage system (LHTESs) is performed on a vertical shell and tube geometry, made of a porous medium filled with a phase change material (PCM). The LHTESs is a cylinder with a corrugated inner surface at a constant temperature above the PCM melting temperature; on the external surface there are heat losses to the outside and the top and bottom surfaces are adiabatic. The PCM used is a pure paraffin wax, the metal foam, instead, is made of aluminum. The phase change process is modelled with the enthalpy-porosity theory, while the Local Thermal Non-Equilibrium (LTNE) and the Darcy-Forchheimer models are adopted to analyse the heat transfer between the paraffin and the metal foam. The solutions of the governing equations are computed with Ansys-Fluent commercial code. The survey considers different conductivity variations on the external wall and distinct corrugated wall geometric parameters, with different wavelengths and wave amplitudes. The results of the numerical simulations, concerning the LHTESs charging phase, are reported as a function of time and compared in terms of melting time, enthalpy stored, and energy loss.

Improving the performance of a small-scale cascade latent heat storage system by using gradual melting temperature storage tank

The highest thermal energy for phase change material (PCM) is stored/discharged with unsubstantial temperature changes during the isothermal phase transition. However, the convective latent heat storage system uses temperature differences between the thermal load and working fluid. It restricts the temperature operation of the storage system since the temperature of the working fluid is limited by the melting temperature of PCM. To overcome the related issue, the present study proposes a configuration for small-scale cascade latent heat storage using three different melting points of the phase change materials. The three-stage cascade system is occupied by paraffin, RT80, and high-density polyethylene for the 1st, 2nd and 3rd storage tanks with melting temperatures of 60.9 °C, 79.6 °C and 115.4 °C, respectively. The overall system demonstrates a better performance than a single tank, with an average temperature variation of 42.9 °C and 34.5 °C during charging and discharging. The effect of partial phase change can be decreased where the power effective for discharging decreases by only 6.3% while the power effective during charging increases by 18.2%. It proves that using a multistage cascade system with gradual melting temperature PCM allows higher performance for a latent heat storage system.

Evaluation and analysis of the improvement in charging time for the high-power fast charging module using phase change material

The advancement of charging time for the fast charging piles facilitates the full adoption of EVs. The benefits of adding the suitable phase change material (PCM) to the thermal control system of the high-power fast charging power module are demonstrated in this experimental study. The effects of different PCM's melting temperature, thermal conductivity, and filling thickness on the improvement of charging time are explored, and the PCM melting rate is visualized to reveal the mechanism of PCM in improving the charging time. The results show that the extension in charging time of 2370 s is found for the charging power module coupled with PCM at the heat generating power of 15 W, and it is extended by 54% and 39% at heat generating power of 25 W and 35 W, respectively. The benefit of applying the PCM in the improvement of charging time for the charging power module is lessened with increasing the air velocity. The optimal PCM melting temperature is 47.5 °C, and it achieves the maximum charging time of 1540 s. The maximum available charging time is 1620 s at the filling PCM thickness of 5.5 mm. Also, the charging time is extended by 510 s when the thermal conductivity of PCM increases from 0.2 W/(m K) to 5 W/(m K). Increasing the heat generating power or decreasing the air velocity will shorten the completed melting time of the used PCM, and the initial melting time is also ahead. A faster PCM melting rate is observed at the lower PCM melting temperature and filling thickness, and this shortens the PCM latent heat role in the thermal control for the charging power module.