Peroxide Intermediates Research Articles

Boosting the bifunctional catalytic activity of Co3O4 on silver and nickel substrates for the alkaline oxygen evolution and reduction reactions

Developing an efficient bifunctional catalyst for oxygen reduction (ORR) and evolution reactions (OER) is a crucial step for the wide commercialization of alkaline water electrolyzers. However, a proper assessment and comparison of various catalysts is still challenging due to the different catalyst substrates and loadings. In this work, Co3O4 spinel nanoparticles (NPs) were investigated as a bifunctional catalyst at different substrates of glassy carbon or Ag bulk substrate or Ni particles and with different loadings. For Co3O4 (800 µg cm-2)/Ag electrode, not only the overpotential for ORR was 50 mV lower than the bare Ag electrode, but also the OER overpotential was 40 mV lower than the sole Co3O4. Besides, less than 1% peroxide intermediate was detected during ORR using the rotating ring disc electrode (RRDE) method, suggesting a 4-electron O2 reduction. Tafel slopes of 70 and 60 mV dec‑1 at Co3O4/Ag were obtained for ORR and OER, respectively. The improved bifunctional activity could be attributed to a synergistic effect between Co3O4 and the Ag support. For the loading effect, it is revealed that the number of accessible sites of Ag surface decreases with increasing the Co3O4 loading, as evaluated from lead-underpotential deposition measurements. Interestingly, after running ORR/OER cycles, the surface area increased by 4–6 times. This surface roughening was also confirmed by SEM and EDX. The study was extended to Co3O4+Ni mixed catalyst to validate the effect of the support on this induced synergism. Hence, this work provides a simple route for designing potential effective catalytic interfaces and contributes to unravelling the influence of the substrate and loading on the catalyst activity for water electrolyzers.

Local pH Gradients Alter Product Selectivity of Electrocatalytic Oxygen Reduction Reaction on La‐Cr‐Co Perovskites

AbstractThe electrochemical production of hydrogen peroxide through the oxygen reduction reaction (ORR) presents the interesting situation where the fully reduced form, H2O, is significantly favored by thermodynamics. Perovskite oxide based catalysts with slow kinetics, or large overpotentials, have been shown to enable production of H2O2 with good selectivity, but this comes at the expense of energy efficiency and production rates. We analyze the structure and electrocatalytic ORR capabilities of a perovskite oxide series based on LaCr1‐xCoxO3. We find that the crystal lattice distorts in two ways as Co content increases – anisotropic compression of the lattice is accompanied by a pinching of angles within the structure, which gives way to compression of B−O bonds at higher Co contents. Product selectivity is observed to change as a function of both catalyst composition and rotation rates of rotating ring‐disk electrode. The rotation‐dependent behavior is attributed to accelerated displacement of surface‐bound peroxide intermediates by a pH gradient at the catalyst surface, and composition‐dependent changes in selectivity are found to correlate to the angular distortion of the crystal lattice. These results highlight the importance of local environments in electrocatalyst reactions and demonstrate that structure and local pH can be used to manipulate product selectivity.

Formate‐Mediated Synthesis of β‐Hydroxysulfides from Olefins and Thiosulfonates via EDA Complex Strategy under Visible Light Irradiation in Air

Comprehensive SummaryA visible‐light‐induced and efficient one‐pot synthesis of β‐hydroxysulfides from olefins, thiosulfonates and HCOOCs using an EDA complex strategy under air atmosphere at room temperature has been disclosed. A plausible radical involved mechanism is proposed. During the reaction process, formates play a crucial role: first, as donors in the EDA complex; second, as providers of the hydrogen source; and third, by generating CO2•– to reduce peroxide intermediates, leading to the formation of β‐hydroxysulfides. In contrast to the previously reported thiol‐oxygen co‐oxidation reactions, this simple and sustainable approach features mild reaction conditions, operational simplicity, odorless and excellent functional group tolerance.

Overlooked Roles and Transformation of Carbon-Centered Radicals Produced from Natural Organic Matter in a Thermally Activated Persulfate System.

The presence and induced secondary reactions of natural organic matter (NOM) significantly affect the remediation efficacy of in situ chemical oxidation (ISCO) systems. However, it remains unclear how this process relates to organic radicals generated from reactions between the NOM and oxidants. The study, for the first time, reported the vital roles and transformation pathways of carbon-centered radicals (CCR•) derived from NOM in activated persulfate (PS) systems. Results showed that both typical terrestrial/aquatic NOM isolates and collected NOM samples produced CCR• by scavenging activated PS and greatly enhanced the dehalogenation performance under anoxic conditions. Under oxic conditions, newly formed CCR• could be oxidized by O2 and generate organic peroxide intermediates (ROO•) to catalytically yield additional •OH without the involvement of PS. Nuclear magnetic resonance (NMR) and Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR-MS) results indicated that CCR• predominantly formed from carboxyl and aliphatic structures instead of aromatics within NOM through hydrogen abstraction and decarboxylation reactions by SO4•- or •OH. Specific anoxic reactions (i.e., dehalogenation and intramolecular cross-coupling reactions) further promoted the transformation of CCR• to more unsaturated and polymerized/condensed compounds. In contrast, oxic propagation of ROO• enhanced bond breakage/ring cleavage and degradation of CCR• due to the presence of additional •OH and self-decomposition. This study provides novel insights into the role of NOM and O2 in ISCO and the development of engineered strategies for creating organic radicals capable of enhancing the remediation of specific contaminants and recovering organic carbon.

Superoxide to Peroxide Interconversion in Ni-TMC Complexes: The Significance of Structure and Spin States.

A deeper comprehension of the characteristics of metal-superoxide and metal-peroxide chemical species is imperative, considering their pivotal functions in oxygen transport, enzymatic activation, and catalytic oxygenations. O2 activation is mediated by the interconversion of superoxide and peroxide species. Even though there are multiple studies on metal-superoxide and -peroxide intermediates, robust examples of their interconversion processes are scarce synthetically. For example, Ni-superoxide/peroxide complexes have been characterized with N-Tetramethylated Cyclam (TMC) ligands with different ring sizes, i.e., Nickel(II)-superoxide complex is characterized with 14-TMC while Nickel(III)-peroxide complex with 12-TMC. Later, both complexes were obtained with 13-TMC ligand by employing different bases; interestingly, no evidence of interconversion between them was identified. What are the factors influencing these processes and why is this preference? We attempt a computational analysis of this issue and provide arguments based on our conclusions. 2-dimensional potential energy scan is performed on the 12-TMC, 13-TMC, and 14-TMC systems to identify the reaction path connecting superoxide and peroxide species. Analyses indicate that structure and spin states play a significant role in determining the probability of interconversion. The superoxide-peroxide interconversion process appears to be bound by their propensity for distinct structural features and spin states.

Screening of highly efficient electrocatalysts for hydrogen peroxide synthesis using single transition metal atoms embedded in carbon vacancy fullerene C60

The electrocatalytic two-electron oxygen reduction reaction (2e– ORR) synthesis of hydrogen peroxide (H2O2) is an eco-friendly process. In this study, density functional theory (DFT) and machine learning (ML) were utilized to systematically explore various single metal atoms anchored on mono-vacancy fullerene C60 (TM@C60) for H2O2 production. Among 19 single-atom catalysts (SACs), Sc@C60 and Y@C60 were identified for high the thermodynamic feasibility of H2O2 formation, exhibiting overpotentials of 0.01 V and 0.02 V, respectively. Moreover, competitive four-electron oxygen reduction reaction (4e– ORR) and hydrogen evolution reaction (HER) were significantly suppressed on these two catalysts. The formation of peroxide intermediates on the two screened SACs was identified as key to achieving high activity and selectivity for H2O2 formation. Analysis using ML methods also revealed that the balance between bond strengths and adsorption energies for O2 is crucial in regulating the performance of 2e– ORR. These results offer important insights for electrocatalytic H2O2 production.

Efficient Ozone Elimination Over MnO2 via Double Moisture-Resistance Protection of Active Carbon and CeO2.

The widespread ozone (O3) pollution is extremely hazardous to human health and ecosystems. Catalytic decomposition into O2 is the most promising method to eliminate ambient O3, while the fast deactivation of catalysts under humid conditions remains the primary challenge for their application. Herein, we elaborately developed a splendidly active and stable Mn-based catalyst with double hydrophobic protection of active carbon (AC) and CeO2 (CeMn@AC), which possessed abundant interfacial oxygen vacancies and excellent desorption of peroxide intermediates (O22-). Under extremely humid (RH = 90%) conditions and a high space velocity of 1200 L h-1 g-1, the optimized CeMn@AC achieved nearly 100% O3 conversion (140 h) at 5 ppm, showing unprecedented catalytic activity and moisture resistance toward O3 decomposition. In situ DRIFTS and theory calculations confirmed that the exceptional moisture resistance of CeMn@AC was ascribed to the double protection effect of AC and CeO2, which cooperatively prevented the competitive adsorption of H2O molecules and their accumulation on the active sites of MnO2. AC provided a hydrophobic reaction environment, and CeO2 further alleviated moisture deterioration of the MnO2 particles exposed on the catalyst surface via the moisture-resistant oxygen vacancies of MnO2-CeO2 crystal boundaries. This work offers a simple and efficient strategy for designing moisture-resistant materials and facilitates the practical application of the O3 decomposition catalysts in various environments.

Synthesis of polyfunctional O-containing 1,3-dioxepines connected with an acetal fragment by low-temperature ozonolysis

The synthesis of 3,5-dioxo-1,7-heptandials, 3,5-dioxo-1,7-heptanediols and 1,3-dioxo-1,7-heptanedicarboxylic acid derivatives by low-temperature ozonolysis of 1,3-dioxepines was carried out for the first time. It is shown that, depending on the conditions of destruction of the intermediate peroxide products of ozonolysis, the corresponding individual dialdehydes, diols, and diesters can be synthesized with high selectivity.

(Invited) Enhancement of Activity of Low-Pt-Content-Catalysts Toward Oxygen Reduction through Admixing with Metal Oxide Cocatalysts

The proton-exchange membrane fuel cell (PEMFC) technology is one of the most promising approaches for energy conversion in automotive applications. Despite the use of expensive noble metal electrocatalysts, the sluggish kinetics of the oxygen reduction reaction (ORR) in acid media, and formation of the undesirable hydrogen peroxide intermediate are still the main drawbacks, on top of the stability problems, when it comes to the widespread commercialization of PEMFC devices. The progress in this subject is greatly hindered by the high cost and scarcity of the state-of-the-art platinum-based materials which are regarded as the most effective cathode catalysts. Therefore, most of the current research studies have been devoted to the optimization of active centers and maximization of their utilization, which should allow the lowering of the cathode Pt loadings without loss of performance and durability. Unfortunately, the problem of electrochemical stability and the danger of generation of higher quantities of the undesirable hydrogen peroxide intermediate may become even more serious in the case of systems utilizing lower amounts of the Pt catalystAmong important strategies is hybridization, activation, and stabilization of carbon-supported Pt catalysts by functionalization through admixing with certain nanostructured and typically substoichiometric metal oxides. Special attention is paid to application of the bi- or multi-metallic Pt-based alloys in their various forms and structures. Additionally, doping of carbon carriers with heteroatoms would produce surface functional groups and active centers capable of not only improving the catalysts’ performance, but also affecting their stability. Among other important issues are such features as porosity, hydrophilicity, and degree of graphitization of carbon components, in addition to the existence of metal–support interactions, high electrochemical active surface area, electronic structure of interfacial Pt, and the feasibility of adsorptive or activating interactions with oxygen molecules.Platinum is a main catalyst for the electroreduction of oxygen, the reaction of primary importance to the technology of low-temperature fuel cells. Because of high cost of platinum. there is a need to significantly lower its loadings at interfaces. But then O2-reduction proceeds often at less positive potentials and produces higher amounts of undesirable H2O2-intermediate. Hybrid supports, which utilize metal oxides (e.g., CeO2, WO3, Ta2O5, Nb2O5, ZrO2), stabilize Pt and carbon nanostructures, diminish their corrosion while exhibiting high activity toward the four-electron (most efficient) reduction of oxygen. Porosity of carbon supports facilitates dispersion and stability of Pt nanoparticles. The catalytic efficiency depends on geometric (decrease of Pt–Pt bond distances) and electronic (increase of d-electron vacancy in Pt) factors, in addition to possible metal-support interactions and interfacial structural changes affecting adsorption and activation of O2-molecule.

How a natural antibiotic uses oxidative stress to kill oxidant-resistant bacteria.

Natural products that possess antibiotic and antitumor qualities are often suspected of working through oxidative mechanisms. In this study, two quinone-based small molecules were compared. Menadione, a classic redox-cycling compound, was confirmed to generate high levels of reactive oxygen species inside Escherichia coli. It inactivated iron-cofactored enzymes and blocked growth. However, despite the substantial levels of oxidants that it produced, it was unable to generate significant DNA damage and was not lethal. Streptonigrin, in contrast, was poorer at redox cycling and did not inactivate enzymes or block growth; however, even in low doses, it damaged DNA and killed cells. Its activity required iron and oxygen, and in vitro experiments indicated that its quinone moiety transferred electrons through the adjacent iron atom to oxygen. Additionally, in vitro experiments revealed that streptonigrin was able to damage DNA without inhibition by catalase, indicating that hydrogen peroxide was not involved. We infer that streptonigrin can reduce bound oxygen directly to a ferryl species, which then oxidizes the adjacent DNA, without release of superoxide or hydrogen peroxide intermediates. This scheme allows streptonigrin to kill a bacterial cell without interference by scavenging enzymes. Moreover, its minimal redox-cycling behavior avoids alerting either the OxyR or the SoxRS systems, which otherwise would block killing. This example highlights qualities that may be important in the design of oxidative drugs. These results also cast doubt on proposals that bacteria can be killed by stressors that merely stimulate intracellular O2- and H2O2 formation.

Understanding the Irreversible Reaction Pathway of the Sacrificial Cathode Additive Li6CoO4

AbstractThe use of a sacrificial cathode additive that contains a large amount of lithium is one potential solution to compensate for the irreversible capacity loss associated with next‐generation anodes such as silicon. Antifluorite‐type Li6CoO4 has attracted attention as a potential cathode additive owing to its remarkably high theoretical lithium extraction capacity. However, the complex mechanism of lithium extraction as well as the oxygen loss from Li6CoO4 is not well understood. A generalizable computational thermodynamics and experimental framework is presented to understand the lithium‐extraction pathway of Li6CoO4. It is found that one lithium per formula unit can be topotactically extracted from Li6CoO4, followed by an irreversible and nontopotactic phase transformation to Li2CoO3 or LiCoO2 depending on the temperature. The results show that peroxide species may form to charge‐compensate for Li extraction which is undesirable as this can lead to gas release during battery operation. It is suggested that charging Li6CoO4 at an elevated temperature that the electrolyte can withstand, redirects the reaction pathway and prevents the formation of intermediate peroxide species making it an effective and stable sacrificial cathode additive.

Tracking the Process of Domino Ring‐Opening and Coupling of Fused Imidazole and Direct Observation of Peroxide Intermediates

Comprehensive SummaryA domino ring‐opening and coupling of imidazolyl annulated heterocycles 1 (1a: 4‐methyl‐1‐(1‐methyl‐1H‐benzo[d]imidazol‐2‐yl)‐4H‐ benzo[d]imidazo[1,5‐a]imidazole, 1b: 1‐(1,5‐dimethyl‐1H‐benzo[d]imidazol‐2‐yl)‐4,7‐dimethyl‐4H‐benzo[d]imidazo[1,5‐a]imidazole) with dioxygen was developed at solvothermal condition, leading to conjugated 1,2‐diamidoalkenes derivatives 2 ((E)‐ArCONHArC=CArNHCOAr (Ar: 1‐methyl‐1H‐benzo[d]imidazolyl (2a), 1,5‐dimethyl‐1H‐benzo[d]imidazolyl (2b))) as single crystals directly. The reaction process was tracked by electrospray ionization mass spectrometry (ESI‐HRMS) and a series of reaction intermediates are detected. 18O2 labeling experiment verified the source of oxygen in 2. Combining evidence from control experiments, nuclear magnetic resonance (NMR) tracking, and crystallography, a seven‐step reaction pathway involving oxygen addition, ring opening, Friedel‐Crafts alkylation, oxidation, and dehydration was proposed and further supported by DFT calculation.

α-Fe2O3-supported Co3O4 nanoparticles to construct highly active interfacial oxygen vacancies for ozone decomposition

Ozone pollution has become one of the most concerned environmental issue. Developing low-cost and efficient catalysts is a promising alternative for ozone decomposition. This work presents a creative strategy that using α-Fe2O3-supported Co3O4 nanoparticles for constructing interfacial oxygen vacancies (Vo) to remove ozone. The efficiency of Co3O4/α-Fe2O3 was superior to that of pure α-Fe2O3 by nearly two times for 200-ppm ozone removal after 6-h reaction at 25 °C, which is ascribed to the highly active interfacial Vo. X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy suggest that the Fe3+–Vo–Co2+ was formed when Co3O4 was loaded in α-Fe2O3. Furthermore, the density functional theory (DFT) calculations reveal the desorption and electron transfer ability of intermediate peroxide (O22−) on Fe3+–Vo–Co2+ are higher than the Vo from other regions. In situ diffuse reflectance Fourier transform (DRIFT) spectroscopy also demonstrate the higher conversion rate of O22− on Co3O4/α-Fe2O3. Base on the intermediates detected, we propose a recycle mechanism of interfacial Vo for ozone removal: O22− is quickly converted to O2− and transformed into O2 on interfacial Vo. Moreover, O2-temperature-programmed desorption (TPD), H2-temperature-programmed reduction (TPR), and electrochemical impedance spectroscopy (EIS) reveal that the oxygen mobility, reducibility, and conductivity of Co3O4/α-Fe2O3 are greatly superior to those of α-Fe2O3, which is contributed to the conversion of O22−. Consequently, our proposed strategy effectively enhances the activity and stability of the bimetallic transition oxides for ozone decomposition.

Reaction of Atmospherically Relevant Sulfur-Centered Radicals with RO2 and HO2

The atmospheric oxidation of dimethyl sulfide and other emitted sulfur species leads to the formation of the methylthio radical, CH3S, which can be further oxidized to the CH3SO and CH3SO2 radicals. We investigated computationally the reactions of these three sulfur-centered radicals with the peroxy radicals ROO and HOO. Our results demonstrate that CH3S and CH3SO react with these peroxy radicals to form short-lived peroxide intermediates, which then decompose via a concerted O-O bond scission and S═O double bond formation that results in an increased valence of the sulfur atom. In contrast, CH3SO2 reacts to form stable CH3S(O)2OOR and CH3S(O)2OOH peroxide products, as sulfur is already at its highest valence. Multireference methods were used to describe these reactions in which the valence of the sulfur atom changes.

Exceptional Ozone Decomposition over δ-MnO2/AC under an Entire Humidity Environment.

Ozone (O3) pollution is highly detrimental to human health and the ecosystem due to it being ubiquitous in ambient air and industrial processes. Catalytic decomposition is the most efficient technology for O3 elimination, while the moisture-induced low stability represents the major challenge for its practical applications. Here, activated carbon (AC) supported δ-MnO2 (Mn/AC-A) was facilely synthesized via mild redox in an oxidizing atmosphere to obtain exceptional O3 decomposition capacity. The optimal 5Mn/AC-A achieved nearly 100% of O3 decomposition at a high space velocity (1200 L g-1 h-1) and remained extremely stable under entire humidity conditions. The functionalized AC provided well-designed protection sites to inhibit the accumulation of water on δ-MnO2. Density functional theory (DFT) calculations confirmed that the abundant oxygen vacancies and a low desorption energy of intermediate peroxide (O22-) can significantly boost O3 decomposition activity. Moreover, a kilo-scale 5Mn/AC-A with low cost (∼1.5 $/kg) was used for the O3 decomposition in practical applications, which could quickly decompose O3 pollution to a safety level below 100 μg m-3. This work offers a simple strategy for the development of moisture-resistant and inexpensive catalysts and greatly promotes the practical application of ambient O3 elimination.

Lipid peroxidation in diamond supported bilayers.

Lipid peroxidation is a process that occurs in cells when they are exposed to oxidative stress. During the process reactive oxygen species attack lipids within the lipid bilayers of cells. Since the products of lipid peroxidation are toxic and carcinogenic, it is important to understand where and how it occurs with nanoscale resolution. The radical intermediates of this process are particularly interesting since they are causing chain reactions damaging large parts of the lipid membranes in cells. However, they are also difficult to measure for the state of the art because they are short lived and reactive. Here, we study the lipid peroxidation of three artificial lipid bilayers on a diamonds substrate that can be used to study lipid peroxidation. In particular, we present a diamond quantum sensing method called T1-relaxometry that allows for in situ measurements and imaging of radical intermediates of lipid peroxidation in these membranes.

The mechanism of cleavage of Evans chiral auxiliaries by LiOOH: origins of the different regioselectivities obtained with LiOH, LiOOH, LiOBn and LiSBn

Oxazolidinones are widely used as chiral auxiliaries in asymmetric synthesis. The chiral auxiliary can be selectively removed using LiOOH, LiOBn or LiSBn, but not LiOH, which instead favours endocyclic cleavage with opening of the oxazolidinone ring. Although Evans originally suggested that the regioselectivity of HO−-mediated hydrolysis may be governed by the relative rates of formation of the two tetrahedral intermediates, whereas the regioselectivity of HOO− cleavage might be determined by their relative breakdown rates, it was not clear why this should be the case. Since then, there appear to have been no mechanistic studies that account for the differing selectivities of LiOH v. LiOOH, and the reason for this difference in selectivity has remained somewhat of an enigma in organic chemistry for many years. Herein, we report DFT computations with M06-2X-D3//B3LYP-D3 to examine the origins of the regioselectivities. The computations predict that all four nucleophiles prefer to attack at the endocyclic carbonyl group, which is less hindered. The barrier for decomposition of the initially formed tetrahedral intermediate determines whether or not the reaction continues all the way to the endocyclic cleavage products. For LiOH, the barrier for decomposition of the intermediate is small and the endocyclic cleavage products are formed. For LiOOH, LiOBn and LiSBn, the decomposition barrier is large, and the exocyclic cleavage pathway instead becomes preferred. An alternative mechanism involving formation of a novel cyclic peroxide intermediate was found to involve a relatively high energy pathway and has been excluded.

Mechanistic insights on base-DMSO mediated aerobic oxidation of (hetero)benzylic C-H bonds

Aerobic oxidation of (hetero)benzylic C-H bonds to ketone products always relies on radical process initiated by transition-metal catalysis. Using inorganic bases, here we report an efficient transition-metal-free strategy, which is enabled by DMSO as both the high-polar solvent and the effective reductant. The ionic mechanism was suggested for this reaction, and a high yield of ketones was obtained by choosing the alkalinity-matched inorganic base with the acidity of (hetero)benzylic C-H bonds. Via kinetic experiments, a mixed mechanism with two reaction pathways was suggested for the generation of ketones, one of which involved the reduction of peroxide intermediates toward alcohols intermediates by DMSO, while the dehydration of peroxide intermediates lead to the direct formation of ketones in the other pathway. These findings not only provide a greener approach for ketones production from (hetero)benzylic oxidation, but also encourage the possible strategy to generate alcohols under inorganic base catalysis.

Encapsulation of HPW and preparation of composites rich in Zr-defects by manual grinding: Synergistic catalysis for efficient oxidative desulfurization at room temperature

The development of catalysts with excellent performance in oxidative desulfurization (ODS) at room temperature will greatly facilitate the advancement of desulfurization technology. An efficient novel strategy, 4-aminopyridine molecular bridging combined with manual grinding, was presented to encapsulate HPW into UiO-66 for achieving stable loading of PW and to produce abundant defects that contribute to the formation of active complexes with strong oxidation ability. The prepared catalyst showed outstanding catalytic activity in the ODS system, achieving full desulfurization in 15 min at room temperature and a low O/S molar ratio. Further investigations reveal that the synergistic catalytic effect of the faulty UiO-66 and PW is mostly responsible for superior catalytic performance. UiO-66 rich in defects promote the decomposition of H2O2 into radicals, and PW can combine with the radicals to form more stable active peroxide intermediates, then exerting the catalytic ability of ODS at room temperature. Such a synergistic catalytic mechanism provides a guide to improving the oxidation ability of PW-based catalysts at room temperature.

The roles of DmsEFAB and MtrCAB in extracellular reduction of iodate by Shewanella oneidensisMR-1 with lactate as the sole electron donor.

To investigate their roles in extracellular reduction of iodate (IO3 - ) with lactate as an electron donor, the gene clusters of dmsEFAB, mtrCAB, mtrDEF and so4360-4357 in Shewanella oneidensis MR-1 were systematically deleted. Deletions of dmsEFAB and/or mtrCAB gene clusters diminished the bacterial ability to reduce IO3 - . Furthermore, DmsEFAB and MtrCAB worked collaboratively to reduce IO3 - of which DmsEFAB played a more dominant role than MtrCAB. MtrCAB was involved in detoxifying the reaction intermediate hydrogen peroxide (H2 O2 ). The reaction intermediate hypoiodous acid (HIO) was also found to inhibit microbial IO3 - reduction. SO4360-4357 and MtrDEF, however, were not involved in IO3 - reduction. Collectively, these results suggest a novel mechanism of extracellular reduction of IO3 - at molecular level, in which DmsEFAB reduces IO3 - to HIO and H2 O2 . The latter is further reduced to H2 O by MtrCAB to facilitate the DmsEFAB-mediated IO3 - reduction. The extracellular electron transfer pathway of S. oneidensis MR-1 is believed to mediate electron transfer from bacterial cytoplasmic membrane, across the cell envelope to the DmsEFAB and MtrCAB on the bacterial outer membrane.