Periodically Poled Lithium Niobate Waveguide Research Articles

Over-8-dB squeezed light generation by a broadband waveguide optical parametric amplifier toward fault-tolerant ultra-fast quantum computers

We achieved continuous-wave 8.3-dB squeezed light generation using a terahertz-order-broadband waveguide optical parametric amplifier by improving a measurement setup from our previous work [T. Kashiwazaki et al., Appl. Phys. Lett. 119, 251104 (2021)], where a low-loss periodically poled lithium niobate (PPLN) waveguide had shown 6.3-dB squeezing at a 6 THz frequency. First, to improve efficiency of the squeezed light detection, we reduced effective optical loss to about 12% by removing extra optics and changing the detection method into a low-loss balanced homodyne measurement. Second, to minimize phase-locking fluctuation, we constructed a frequency-optimized phase-locking system by comprehending its frequency responses. Finally, we found optimal experimental parameters of a measurement frequency and a pump power from their dependences for the squeezing levels. The measurement frequency was decided as 11 MHz to maximize a clearance between shot and circuit noises. Furthermore, pump power was optimized as 660 mW to get higher squeezing level while suppressing anti-squeezed-noise contamination due to an imperfection of phase locking. Note that this over-8-dB squeezing is achieved without any loss-correction and circuit-noise correction. Moreover, it is shown that the squeezing level soon after our PPLN waveguide is estimated at over 10 dB, which is thought to be mainly restricted by the waveguide loss. This broadband highly squeezed light opens the possibility to realize fault-tolerant ultra-fast optical quantum computers.

Proposal of optically tunable and reconfigurable multi-channel bandstop filter using sum-frequency generation in a PPLN waveguide

A multi-wavelength bandstop filter is proposed and numerically demonstrated using the sum-frequency generation (SFG) process in a waveguide of periodically poled lithium niobate (PPLN). This proposed device achieves channels number reconfigurable, central filtering wavelength of each filtering channel independently tunable and extinction ratios (ERs) equalized via all-optical methods.

Thermally tunable and efficient second-harmonic generation on thin-film lithium niobate with integrated micro-heater.

In this Letter, we report thermo-optic tunable and efficient second-harmonic generation (SHG) based on an X-cut periodically poled lithium niobate (PPLN) waveguide. By applying an on-chip heater with thermo-isolation trenches and combining a type-0 quasi-phase matching mechanism, we experimentally achieve a high on-chip SHG conversion efficiency of 2500-3000% W-1 cm-2 and a large tuning power efficiency of 94 pm/mW inside a single 5-mm-long straight PPLN waveguide. Our design is for energy-efficient, high-performance nonlinear applications, such as wavelength conversion, highly tunable coherent light sources, and photon-pair generation.

All-optical wavelength conversion of a 92-Gb/s 16-QAM signal within the C-band in a single thin-film PPLN waveguide.

Tunable all-optical wavelength conversion (AOWC) within 151 nm bandwidth is demonstrated in a thin-film periodically poled lithium niobate (PPLN) waveguide, which utilizes the cascaded second-harmonic generation and difference-frequency generation (cSHG/DFG) process. Also, in the same waveguide, AOWC of a 92-Gb/s 16-ary quadrature amplitude modulated (16-QAM) signal within the C-band is successfully achieved. For Bit-error ratio (BER) measurements, we obtain a negligible optical signal-to-noise ratio (OSNR) penalty (<0.2 dB) for the converted idler wave at a BER of 1e-3.

Ultra-broadband and low-loss edge coupler for highly efficient second harmonic generation in thin-film lithium niobate

Thin-film lithium niobate is a promising material platform for integrated nonlinear photonics, due to its high refractive index contrast with the excellent optical properties. However, the high refractive index contrast and correspondingly small mode field diameter limit the attainable coupling between the waveguide and fiber. In second harmonic generation processes, lack of efficient fiber-chip coupling schemes covering both the fundamental and second harmonic wavelengths has greatly limited the overall efficiency. We design and fabricate an ultra-broadband tri-layer edge coupler with a high coupling efficiency. The coupler allows efficient coupling of 1 dB / facet at 1550 nm and 3 dB / facet at 775 nm. This enables us to achieve an ultrahigh overall second harmonic generation normalized efficiency (fiber-to-fiber) of 1027 % W − 1 cm − 2 (on-chip second harmonic efficiency ∼3256 % W − 1 cm − 2) in a 5-mm-long periodically-poled lithium niobate waveguide, which is two to three orders of magnitude higher than that in state-of-the-art devices.

Broadband second-harmonic generation in step-chirped periodically poled lithium niobate waveguides.

Periodically poled lithium niobate (PPLN) structures on a chip enable efficient second-order nonlinear optical effects, benefiting from the tight light confinement and the utilization of d33. Here, we report a broadband second-harmonic (SH) generation in a step-chirped PPLN waveguide on X-cut lithium niobate on insulator (LNOI). The high fidelity of the poling period is demonstrated over the whole length of 7 mm using a non-destructive technique of piezoresponse force microscopy. The SH signal was continuously observed in the step-chirped PPLN waveguides while scanning the wavelength of the pump laser from 1550 nm to 1660 nm. The SH conversion efficiency was measured to be 9.6 % W-1 cm-2 at 1642 nm. This work will benefit wavelength conversions of light sources with wideband spectra.

Self-phase modulation in periodically-poled thin-film lithium niobate waveguides

Self-phase modulation in periodically-poled thin-film lithium niobate waveguides

Over-30-dB gain and 1-dB noise figure phase-sensitive amplification using a pump-combiner-integrated fiber I/O PPLN module.

Phase-sensitive amplifiers (PSAs) via the optical parametric amplification (OPA) process are capable of near-noiseless amplification, which can improve the performance of optical communications systems. OPA based on periodically poled lithium niobate (PPLN) waveguides is a proven means to implement a PSA with low additional nonlinear effects, such as frequency chirp, stimulated Brillouin scattering, and parametric crosstalk due to unwanted nonlinear interactions among pump and other signal waves. However, fiber compatibility is a challenge because optical coupling loss between a fiber and PPLN waveguide limits essential performance such as the gain and noise figure (NF), which makes PSAs still far from being practical. In this work, we developed a PPLN-waveguide-based pump-combiner-integrated OPA module with fiber input and output ports. With our recent development and optimization of the OPA module, we demonstrated high-performance phase-sensitive amplification with a gain of over 30 dB and an NF of 1.0 dB. In addition, we observed a 3-dB gain bandwidth of over 65 nm and flat NF characteristics in that wavelength band. The high conversion efficiency and high damage resistance of the PPLN waveguide, obtained by employing direct bonding and dry etching techniques, provide a high parametric gain. The low-loss coupling for the signal and pump between the fiber and a spot-size-converter-integrated PPLN waveguide through the dichroic beam combiner improve not only the gain but also the NF of the amplifier. Using the PSA as a preamplifier, the low-noise characteristics were confirmed by the sensitivity improvement provided by the low NF value.

Towards generation of optical frequency comb in the short-wavelength visible region using periodically poled lithium niobate waveguides

We demonstrate the spectral broadening of an octave-spanning erbium-based frequency comb in two types of periodically poled lithium niobate (PPLN) waveguides. Spectral peaks in the broadened comb are observed at wavelengths that fulfill the phase-matching conditions designed for the waveguides. We found that an appropriately designed PPLN waveguide should enable the generation of the comb spectrum in the short-wavelength visible region.

CW demonstration of SHG spectral narrowing in a PPLN waveguide generating 2.5 W at 780 nm.

Periodically poled lithium niobate (PPLN) waveguides are a proven and popular means for efficient wavelength conversion. However, conventional PPLN waveguides typically have small mode field diameters (MFD) (≲6 µm) or significant insertion and/or propagation losses, limiting their ability to operate at multi-watt power levels. In this work we utilise zinc indiffused PPLN ridge waveguides that have a larger MFD, favourable pump/SHG modal overlap, and low insertion losses. Here for the first time, we have demonstrated continuous wave (CW) spectral narrowing from a PPLN waveguide, both with high efficiency and multi-watt second harmonic generation (SHG). 2.5 W of 780 nm has been produced by SHG of an amplified 1560 nm telecom laser with a device efficiency of 58% in a 4.0-cm long ridge waveguide. We have modelled conversion efficiency and applied experimentally measured waveguide parameters to show excellent agreement to the SHG spectra. Spectral narrowing of the full width half maximum (FWHM) of 35.7% has been measured as the nonlinear drive is increased. This work demonstrates that single-pass, multi-watt, CW SHG at 780 nm is feasible from our PPLN waveguide in the large conversion regime.

Demonstration of Tunable Optical Aggregation of QPSK to 16-QAM Over Optically Generated Nyquist Pulse Trains Using Nonlinear Wave Mixing and a Kerr Frequency Comb

A tunable and reconfigurable optical aggregation system is experimentally demonstrated. Optical Nyquist pulses are generated on multiple channels using a microresonator-based Kerr optical frequency comb and insertion of uniform lines by an intensity modulator. Data are modulated on optically generated Nyquist pulses and aggregated through nonlinear wave mixing in a periodically poled lithium niobate (PPLN) waveguide. Two quadrature-phase-shift-keying (QPSK) channels are aggregated to a single 16-quadrature amplitude modulation (16-QAM) channel of Nyquist pulses. To demonstrate the system tunability, we perform aggregation over different baud rates and different modulation formats. The reconfigurability of the system is demonstrated by aggregating two binary-phase-shift-keying (BPSK) channels into a QPSK or a 2-level amplitude-shift keying and a 2-level phase-shift keying (2-ASK/2-PSK) channel by tuning the relative phase and amplitude of the inputs. Furthermore, three BPSK channels are aggregated into one 4-ASK/2-PSK channel. The quality of the aggregated channel is investigated using two different approaches for wave mixing in the PPLN waveguide.

Frequency-Multiplexed Photon Pairs Over 1000 Modes from a Quadratic Nonlinear Optical Waveguide Resonator with a Singly Resonant Configuration.

We demonstrate a frequency multiplexed photon pair generation based on a quadratic nonlinear optical waveguide inside a cavity which confines only signal photons without confining idler photons and the pump light. We monolithically constructed the photon pair generator by a periodically poled lithium niobate (PPLN) waveguide with a high reflective coating for the signal photons around 1600nm and with antireflective coatings for the idler photons around 1520nm and the pump light at 780nm at the end faces of the PPLN waveguide. We observed a comblike photon pair generation with a mode spacing of the free spectral range of the cavity. Unlike the conventional multiple resonant photon pair generation experiments, the photon pair generation was incessant within a range of 80nm without missing teeth due to a mismatch of the energy conservation and the cavity resonance condition of the photons, resulting in over 1000-mode frequency multiplexed photon pairs in this range.

Design of spontaneous parametric down-conversion in integrated hybrid SixNy-PPLN waveguides.

High-efficient and high-purity photon sources are highly desired for quantum information processing. We report the design of a chip-scale hybrid SixNy and thin film periodically-poled lithium niobate waveguide for generating high-purity type-II spontaneous parametric down-conversion (SPDC) photons in the telecommunication band. The modeled second harmonic generation efficiency of 225% W-1 • cm-2 is obtained at 1560nm. Joint spectral analysis is performed to estimate the frequency correlation of SPDC photons, yielding intrinsic purity with up to 95.17%. The generation rate of these high-purity photon pairs is estimated to be 2.87 × 107 pairs/s/mW within the bandwidth of SPDC. Our chip-scale hybrid waveguide design has the potential for large-scale on-chip quantum information processing and integrated photon-efficient quantum key distribution through high-dimensional time-energy encoding.

Phase noise of frequency doublers in optical clock lasers.

Frequency doublers are widely used in high-resolution spectroscopy to shift the operation wavelength of a laser to a more easily accessible or otherwise preferable spectral region. We investigate the use of a periodically-poled lithium niobate (PPLN) waveguide frequency doubler in an optical clock. We focus on the phase evolution between the fundamental (1396 nm) and frequency-doubled (698 nm) light and its effect on clock performance. We find that the excess phase noise of the doubler under steady-state operation is at least two orders of magnitude lower than the noise of today's best interrogation lasers. Phase chirps related to changes of the optical power in the doubler unit and their influence on the accuracy of optical clocks are evaluated. We also observe substantial additional noise when characterizing the doubler unit with an optical frequency comb instead of using two identical waveguide doublers.

Ultrahigh-efficiency wavelength conversion in nanophotonic periodically poled lithium niobate waveguides

Periodically poled lithium niobate (PPLN) waveguide is a powerful platform for efficient wavelength conversion. Conventional PPLN converters however typically require long device lengths and high pump powers due to the limited nonlinear interaction strength. Here we use a nanostructured PPLN waveguides to demonstrate an ultrahigh normalized efficiency of 2600%/W-cm$^2$ for second-harmonic generation of 1.5-$\mu$m radiation, more than 20 times higher than that in state-of-the-art diffused waveguides. This is achieved by a combination of sub-wavelength optical confinement and high-fidelity periodic poling at a first-order poling period of 4 $\mu$m. Our highly integrated PPLN waveguides are promising for future chip-scale integration of classical and quantum photonic systems.

Second harmonic generation in periodically poled lithium niobate waveguides with stitching errors

Depending on the chosen fabrication process, nonlinear waveguides realized in periodically oriented material such as periodically poled lithium niobate (PPLN) can present different fabrication errors. In this paper, we present a detailed numerical study of the impact on the nonlinear performances of one or several stitching errors occurring during the realization of the periodic domains by e-beam writing. This study shows that contrary to what was expected, a single finite stitching error does not simply decrease the nonlinear efficiency but splits the second harmonic (SH) signal into a double peak spectrum, where the position of the peaks and their width at half-maximum depend not only on the poling period, the total length of the grating, and the waveguide parameters, but also on the amplitude and the position of the defect. The numerical results are confirmed by second harmonic generation (SHG) experiments performed in PPLN waveguides obtained by Soft Proton Exchange and where the nonlinear grating was composed of one to four e-beam-written 1.5-mm-long PPLN sections between which important stitching errors can occur. In this case the spectrum can be quite complicated. It is worth noting that similar errors (domains merging or missing domains) can occur also in the e-field poling process but they are randomly distributed along the propagation path. Therefore, this study is a first attempt to take them into account to explain experimental results and indicate the steps that have to be taken to improve the quality of the components.

Mach-Zehnder interferometer using frequency-domain beamsplitter.

We demonstrate a first-order interference between coherent light at 1580 nm and 795 nm by using a frequency-domain Mach-Zehnder interferometer (MZI). The MZI is implemented by two frequency-domain BSs based on a second-order nonlinear optical effect in a periodically-poled lithium niobate waveguide with a strong pump light. The observed visibility is over 0.99 at 50% conversion efficiencies of the BSs. Toward photonic quantum information processing, sufficiently small background photon rate is necessary. From measurement results with a superconducting single photon detector (SSPD), we discuss the feasibility of the frequency-domain MZI in a quantum regime. Our estimation shows that the single photon interference with the visibility above 0.9 is feasible with practical settings.

Tunable optical frequency comb generation in a periodically poled lithium niobate waveguide based on stimulated Brillouin scattering

We propose and demonstrate a technique for the generation of an optical frequency comb (OFC) in a periodically poled lithium niobate (PPLN) waveguide based on stimulated Brillouin scattering. A single continuous wave laser is sent to a multi-wavelength Brillouin erbium fibre laser for generating a set of coherent and phase-locked multi-wavelength spectral lines. They are injected into a PPLN waveguide to obtain an OFC. We investigate the influence of the cavity structure on the OFC property in our two different schemes. The number of comb lines is affected by the 980 pump current and Brillouin pump power. The OFCs are tunable in a large range by changing their central wavelength.

Cross-correlation frequency-resolved optical gating scheme based on a periodically poled lithium niobate waveguide for an optical arbitrary waveform measurement

This study proposes a novel scheme of a crosscorrelation frequency-resolved optical gating (X-FROG) measurement for an optical arbitrary waveform (OAW) based on the sum frequency generation (SFG) effect of a periodically poled lithium niobate (PPLN) waveguide. Based on the SFG effect and combined with the principal component generalized projects algorithm on a matrix, the theory model of the scheme is established. Using Matlab, the proposed OAW measurement X-FROG scheme using the PPLN waveguide is simulated and studied. Simulation results show that a rectangular pulse is a suitable gate pulse because of its low errors. Moreover, the increased complexity of OAW and phase mismatch decrease measurement accuracy.

Highly efficient heralded single-photon source for telecom wavelengths based on a PPLN waveguide.

We present the realization of a highly efficient photon pair source based on spontaneous parametric downconversion (SPDC) in a periodically poled lithium niobate (PPLN) ridge waveguide. The source is suitable for long distance quantum communication applications as the photon pairs are located at the centers of the telecommunication O- and C- band at 1312 nm and 1557 nm. The high efficiency is confirmed by a conversion efficiency of 4 × 10-6 - which is to our knowledge among the highest conversion efficiencies reported so far - and a heralding efficiency of 64.1 ± 2.1%. The heralded single-photon properties are confirmed by the measurement of the photon statistics with a Click/No-Click method as well as the heralded g(2)-function. A minimum value for g(2)(0) of 0.001 ± 0.0003 indicating clear antibunching has been observed.