Performance Of Beamline Research Articles

Ex situ metrology and data analysis for optimization of beamline performance of aspherical pre-shaped x-ray mirrors at the advanced light source.

Super high quality aspherical x-ray mirrors with a residual slope error of ∼100 nrad (root-mean-square) and a height error of ∼1-2 nm (peak-to-valley), and even lower, are now available from a number of the most advanced vendors utilizing deterministic polishing techniques. The mirror specification for the fabrication is based on the simulations of the desired performance of the mirror in the beamline optical system and is normally given with the acceptable level of deviation of the mirror figure and finish from the desired ideal shape. For example, in the case of aspherical x-ray mirrors designed for the Advanced Light Source (ALS) QERLIN beamline, the ideal shape is defined with the beamline application (conjugate) parameters and their tolerances. In this paper, we first discuss an original procedure and dedicated software developed at the ALS X-Ray Optics Laboratory (XROL) for optimization of beamline performance of pre-shaped hyperbolic and elliptical mirrors. The optimization is based on results of ex situ surface slope metrology and consists in minimization of the mirror shape error by determining the conjugate parameters of the best-fit ideal shape within the specified tolerances. We describe novel optical metrology instrumentation, measuring techniques, and analytical methods used at the XROL for acquisition of surface slope data and optimization of the optic's beamline performance. The high efficacy of the developed experimental methods and data analysis procedures is demonstrated in results of measurements with and performance optimization of hyperbolic and elliptical cylinder mirrors designed and fabricated for the ALS QERLIN beamline.

Metrology for optical components of Taiwan Photon Source beamlines.

To ensure the high performance of beamlines in Taiwan Photon Source, the metrology of the beamline optical components is essential to realize the theoretical optical simulation. The design and performance of a long-trace profiler (LTP) with moving optical head is described. A LTP is used as a metrological tool for the assembly and correction of optical components at the beamline. For a water-cooled mirror, a LTP serves to optimize the surface profile to a slope error of 0.1 µrad (rms) and adequate thermal conductance. To correct a bendable cooling mirror in a twisted condition, the sagittal slope is decreased by a screw adjustment through the LTP measurement. For the double-crystal monochromator (DCM) with flow-induced vibrations, we proposed an approach to stiffen the bellows hose partially inside the vacuum chamber. From an investigation of the vibrational spectra of the DCM before and after the treatment with the aid of the autocollimator, the current approach is confirmed to be an effective solution for suppression of vibration.

Fast and accurate data collection for macromolecular crystallography using the JUNGFRAU detector

The accuracy of X-ray diffraction data is directly related to how the X-ray detector records photons. Here we describe the application of a direct-detection charge-integrating pixel-array detector (JUNGFRAU) in macromolecular crystallography (MX). JUNGFRAU features a uniform response on the subpixel level, linear behavior toward high photon rates, and low-noise performance across the whole dynamic range. We demonstrate that these features allow accurate MX data to be recorded at unprecedented speed. We also demonstrate improvements over previous-generation detectors in terms of data quality, using native single-wavelength anomalous diffraction (SAD) phasing, for thaumatin, lysozyme, and aminopeptidase N. Our results suggest that the JUNGFRAU detector will substantially improve the performance of synchrotron MX beamlines and equip them for future synchrotron light sources.

Imaging Capabilities, Performance and Applications of the Hard X-ray Nanoprobe Beamline at NSLS-II

Imaging Capabilities, Performance and Applications of the Hard X-ray Nanoprobe Beamline at NSLS-II

SwissFEL Aramis beamline photon diagnostics.

The SwissFEL Aramis beamline, covering the photon energies between 1.77 keV and 12.7 keV, features a suite of online photon diagnostics tools to help both users and FEL operators in analysing data and optimizing experimental and beamline performance. Scientists will be able to obtain information about the flux, spectrum, position, pulse length, and arrival time jitter versus the experimental laser for every photon pulse, with further information about beam shape and size available through the use of destructive screens. This manuscript is an overview of the diagnostics tools available at SwissFEL and presents their design, working principles and capabilities. It also features new developments like the first implementation of a THz-streaking based temporal diagnostics for a hard X-ray FEL, capable of measuring pulse lengths to 5 fs r.m.s. or better.

Performance of the HERMES beamline at the carbon K-edge

Contamination of soft X-rays beamline optics due to carbon cracking and deposition under X- ray irradiation is especially critical for spectromicroscopy operations near the carbon K-absorption edge from organic materials, polymers and nanoparticles. In this paper we present the strategy and procedure followed on the HERMES beamline (Synchrotron SOLEIL) to minimize carbon contamination of the beamline optics. Measurements on a complex organic test sample are reported to demonstrate the performance of the beamline at the carbon K-edge in imaging, spectroscopy and spectromicroscopy modes.

Long, elliptically bent, active X-ray mirrors with slope errors

Actively bent X-ray mirrors are important components of many synchrotron and X-ray free-electron laser beamlines. A high-quality optical surface and good bending performance are essential to ensure that the X-ray beam is accurately focused. Two elliptically bent X-ray mirror systems from FMB Oxford were characterized in the optical metrology laboratory at Diamond Light Source. A comparison of Diamond-NOM slope profilometry and finite-element analysis is presented to investigate how the 900 mm-long mirrors sag under gravity, and how this deformation can be adequately compensated using a single, spring-loaded compensator. It is shown that two independent mechanical actuators can accurately bend the trapezoidal substrates to a range of elliptical profiles. State-of-the-art residual slope errors of <200 nrad r.m.s. are achieved over the entire elliptical bending range. High levels of bending repeatability (ΔR/R = 0.085% and 0.156% r.m.s. for the two bending directions) and stability over 24 h (ΔR/R= 0.07% r.m.s.) provide reliable beamline performance.

Performance on absolute scattering intensity calibration and protein molecular weight determination at BL16B1, a dedicated SAXS beamline at SSRF

The optical system and end-station of bending-magnet beamline BL16B1, dedicated to small-angle X-ray scattering (SAXS) at the Shanghai Synchrotron Radiation Facility, is described. Constructed in 2009 and upgraded in 2013, this beamline has been open to users since May 2009 and supports methodologies including SAXS, wide-angle X-ray scattering (WAXS), simultaneous SAXS/WAXS, grazing-incidence small-angle X-ray scattering (GISAXS) and anomalous small-angle X-ray scattering (ASAXS). Considering that an increasing necessity for absolute calibration of SAXS intensity has been recognized in in-depth investigations, SAXS intensity is re-stated according to the extent of data processing, and the absolute intensity is suggested to be a unified presentation of SAXS data in this article. Theory with a practical procedure for absolute intensity calibration is established based on BL16B1, using glass carbon and water as primary and secondary standards, respectively. The calibration procedure can be completed in minutes and shows good reliability under different conditions. An empirical line of scale factor estimation is also established for any specific SAXS setup at the beamline. Beamline performance on molecular weight (MW) determination is provided as a straightforward application and verification of the absolute intensity calibration. Results show good accuracy with a deviation of less than 10% compared with the known value, which is also the best attainable accuracy in recent studies using SAXS to measure protein MW. Fast MW measurement following the demonstrated method also enables an instant check or pre-diagnosis of the SAXS performance to improve the data acquisition.

Dispersion relations of the acoustic modes in divalent liquid metals

Collective dynamics in liquid Ca and liquid Cd was studied by inelastic x-ray scattering (IXS). Using our experimental technique to prepare proper sample cells and high performance of an IXS beamline (BL35XU) at SPring-8 in Japan, the dynamic structure factor with reasonable statistics was obtained for these divalent liquid metals. For both liquids, the dynamic structure factor at low Q exhibits a central peak with a shoulder or small hump clearly visible on each side, and the inelastic excitation energy determined using the model function composed of Lorentzian and the damped harmonic oscillator function disperses with increasing Q . The dispersion curves of these liquids were compared with that of the longitudinal acoustic phonon in each crystalline phase. From these results, clear difference in the interatomic interaction be- tween liquid Ca and liquid Cd was inferred.

Design and performance of BOREAS, the beamline for resonant X-ray absorption and scattering experiments at the ALBA synchrotron light source

The optical design of the BOREAS beamline operating at the ALBA synchrotron radiation facility is described. BOREAS is dedicated to resonant X-ray absorption and scattering experiments using soft X-rays, in an unusually extended photon energy range from 80 to above 4000 eV, and with full polarization control. Its optical scheme includes a fixed-included-angle, variable-line-spacing grating monochromator and a pair of refocusing mirrors, equipped with benders, in a Kirkpatrick-Baez arrangement. It is equipped with two end-stations, one for X-ray magnetic circular dichroism and the other for resonant magnetic scattering. The commissioning results show that the expected beamline performance is achieved both in terms of energy resolution and of photon flux at the sample position.

HYBRID Simulations of Diffraction-Limited Focusing with Kirkpatrick-Baez Mirrors for a Next-Generation In Situ Hard X-ray Nanoprobe

Next-generation hard X-ray nanoprobe beamlines such as the In Situ Nanoprobe (ISN) beamline being planned at the Advanced Photon Source aim at providing very high spatial resolution while also enabling very high focused flux, to study complex materials and devices using fast, multidimensional imaging across many length scales. The ISN will use diffractive optics to focus X-rays with a bandpass of ∆E/E = 10−4 into a focal spot of 20 nm or below. Reflective optics in Kirkpatrick-Baez geometry will be used to focus X-rays with a bandpass as large as ∆E/E = 10−2 into a focal spot of 50 nm. Diffraction-limited focusing with reflective optics is achieved by spatial filtering and use of a very long, vertically focusing mirror. To quantify the performance of the ISN beamline, we have simulated the propagation of both partially and fully coherent wavefronts from the undulator source, through the ISN beamline and into the mirror-based focal spot. Simulations were carried out using the recently developed software “HYBRID.”

Compound refractive lenses as prefocusing optics for X-ray FEL radiation.

The performance of X-ray free-electron laser beamlines may be limited by the angular aperture. Compound refractive lenses (CRLs) can be employed to prefocus the X-ray beam, thereby increasing the beamline transmission. A prefocusing CRL was implemented in the X-ray transport of the Matter under Extreme Conditions Instrument at the Linac Coherent Light Source. A significant improvement in the beamline transmission was calculated over the 3-10 keV photon energy range. At 5 keV, the relative X-ray intensity was measured and a factor of four increase was seen in the beamline transmission. The X-ray focus was also determined by the ablation imprint method.

Upgrade of the 30-m x-ray pencil beam line at the Institute of Space and Astronautical Science

The 30-m x-ray pencil beam line at the Institute of Space and Astronautical Science has been upgraded. The vacuum chamber has been replaced by a new cylindrical chamber of diameter 1.8 m and length 11.3 m. Stages on which a telescope and detectors had been mounted were also replaced. At the same time, a new charge-coupled device consisting of 1240×1152 pixels of size 22.5×22.5 μm2 was introduced. The detector stage can be moved along the x-ray beam in the vacuum chamber, which enables us to vary the distance between the sample and the detectors from 0.7 to 9 m. The two stages can be moved in a square region 500×500 mm2 in the plane normal to the x-ray beam. The pitching of moving axes of Y direction (horizontal and normal to the beam) of the sample and the detector stages is somewhat large, but does not exceed 60 arc sec. The pitching of the other axes and the yawing of all the axes are less than 30 arc sec. As for rolling, we could obtain only the upper limits because of the difficulty in measuring them. The upper limit of the Z direction (vertical and normal to the beam) of the detector stage moving axis is somewhat large and is about 60 arc sec, and those of the other axes are less than 30 arc sec. A summary of the beam line performance is presented. Soon after the upgrade, the ASTRO-H Soft X-ray telescopes were calibrated in this beam line.

Compact representations of partially coherent undulator radiation suitable for wave propagation

Undulator radiation is partially coherent in the transverse plane, with the degree of coherence depending on the ratio of the electron beam phase space area (emittance) to the characteristic radiation wavelength $\ensuremath{\lambda}$. On the other hand, numerical codes used to predict x-ray beam line performance can typically only propagate coherent fields from the source to the image plane. We investigate methods for representing partially coherent undulator radiation using a suitably chosen set of coherent fields that can be used in standard wave propagation codes, and discuss such ``coherent mode expansions'' for arbitrary degrees of coherence. In the limit when the electron beam emittance along at least one direction is much larger than $\ensuremath{\lambda}$ the coherent modes are orthogonal and therefore compact; when the emittance approaches $\ensuremath{\lambda}$ in both planes we discuss an economical method of defining the relevant coherent fields that samples the electron beam phase space using low-discrepancy sequences.

HERMES: a soft X-ray beamline dedicated to X-ray microscopy.

The HERMES beamline (High Efficiency and Resolution beamline dedicated to X-ray Microscopy and Electron Spectroscopy), built at Synchrotron SOLEIL (Saint-Auban, France), is dedicated to soft X-ray microscopy. The beamline combines two complementary microscopy methods: XPEEM (X-ray Photo Emitted Electron Microscopy) and STXM (Scanning Transmission X-ray Microscopy) with an aim to reach spatial resolution below 20 nm and to fully exploit the local spectroscopic capabilities of the two microscopes. The availability of the two methods within the same beamline enables the users to select the appropriate approach to study their specific case in terms of sample environment, spectroscopy methods, probing depth etc. In this paper a general description of the beamline and its design are presented. The performance and specifications of the beamline will be reviewed in detail. Moreover, the article is aiming to demonstrate how the beamline performances have been specifically optimized to fulfill the specific requirements of a soft X-ray microscopy beamline in terms of flux, resolution, beam size etc. Special attention has been dedicated to overcome some limiting and hindering problems that are usually encountered on soft X-ray beamlines such as carbon contamination, thermal stability and spectral purity.

Optical design and multi-length-scale scanning spectro-microscopy possibilities at the Nanoscopium beamline of Synchrotron Soleil.

The Nanoscopium 155 m-long beamline of Synchrotron Soleil is dedicated to scanning hard X-ray nanoprobe techniques. Nanoscopium aims to reach ≤100 nm resolution in the 5-20 keV energy range for routine user experiments. The beamline design tackles the tight stability requirements of such a scanning nanoprobe by creating an overfilled secondary source, implementing all horizontally reflecting main beamline optics, applying high mechanical stability equipment and constructing a dedicated high-stability building envelope. Multi-technique scanning imaging and tomography including X-ray fluorescence spectrometry and spectro-microscopy, absorption, differential phase and dark-field contrasts are implemented at the beamline in order to provide simultaneous information on the elemental distribution, speciation and sample morphology. This paper describes the optical concept and the first measured performance of the Nanoscopium beamline followed by the hierarchical length-scale multi-technique imaging experiments performed with dwell times down to 3 ms per pixel.

Design and performance of the APPLE-Knot undulator.

Along with the development of accelerator technology, synchrotron emittance has continuously decreased. This results in increased brightness, but also causes a heavy heat load on beamline optics. Recently, optical surfaces with 0.1 nm micro-roughness and 0.05 µrad slope error (r.m.s.) have become commercially available and surface distortions due to heat load have become a key factor in determining beamline performance, and heat load has become a serious problem at modern synchrotron radiation facilities. Here, APPLE-Knot undulators which can generate photons with arbitrary polarization, with low on-axis heat load, are reported.

Design and performance of high-pressure PLANET beamline at pulsed neutron source at J-PARC

PLANET is a time-of-flight (ToF) neutron beamline dedicated to high-pressure and high-temperature experiments. The large six-axis multi-anvil high-pressure press designed for ToF neutron diffraction experiments enables routine data collection at high pressures and high temperatures up to 10GPa and 2000K, respectively. To obtain clean data, the beamline is equipped with the incident slits and receiving collimators to eliminate parasitic scattering from the high-pressure cell assembly. The high performance of the diffractometer for the resolution (Δd/d~0.6%) and the accessible d-spacing range (0.2–8.4Å) together with low-parasitic scattering characteristics enables precise structure determination of crystals and liquids under high pressure and temperature conditions.

Performance of BL-8 dispersive and BL-9 scanning EXAFS beamlines at Indus-2 synchrotron

There are two EXAFS beamlines at 2.5 GeV Indus-2 synchrotron source at Raja Ramanna Center for Advanced Technology, Indore (India). One is BL-8 dispersive type beamline and another is BL-9 scanning type beamline. In order to evaluate the performance and usefulness of the two beamlines, studies of the XAFS spectra at Cu K-edge in copper metal and in a copper complex recorded at these beamlines have been presented. From this sample study and in general, it has been found that the range of the EXAFS data is more in BL-9 than BL-8. However, the bond lengths obtained from EXAFS data analysis are comparable for both the beamlines. Due to larger damping of EXAFS oscillations at higher energies in BL-8, higher disorder is obtained in BL-8. The resolution in the pre-edge and XANES region has been found to be more in BL-9. The advantage of BL-8 is that spectra can be recorded very quickly (~300 ms) and hence beamtime is easily available. Further, BL-8 is useful for performing in situ and time resolved studies. In BL-9, the time taken to record the spectrum is quite large (~40 min) and hence it takes longer to get access to this beamline.

Application of the time-invariant linear filter approximation to parametrization of surface metrology with high-quality x-ray optics

We investigate the time-invariant linear filter (TILF) approach to optimally parameterize the surface metrology of high-quality x-ray optics considered as a result of a stationary uniform random process. The approach is a generalization of autoregressive moving average (ARMA) modeling of one-dimensional slope measurements with x-ray mirrors considered. We show that the suggested TILF approximation has all the advantages of one-sided autoregressive and ARMA modeling, allowing a high degree of confidence when fitting the metrology data with a limited number of parameters. Compared to ARMA modeling, the TILF approximation gains in terms of better fitting accuracy and the absence of the causality limitation. Moreover, the TILF approach can be directly generalized to two-dimensional random fields. With the determined model parameters, the surface topography of prospective beamline optics can be reliably forecast before they are fabricated. These forecast metrology data, containing essential and reliable statistical information about the existing optics which are fabricated by the same vendor and technology, but generally, have different sizes, and slope and height root-mean-square variations, are vitally needed for numerical simulations of the performance of new x-ray beamlines and those under upgrade.