Peak Frequency Research Articles

Temperature dependence of spatial nanoheterogeneities of shear modulus in supercooled glycerol.

The boson peak in the terahertz vibrational spectrum carries information about nano-heterogeneities in the shear modulus in glass formers. Its evolution upon heating or cooling in a supercooled liquid state may shed light on the temperature dependence of heterogeneities. For this purpose, an analysis of the light scattering spectra of supercooled glycerol in the spectral range of the boson peak and fast relaxation was carried out and the parameters of the boson peak in the temperature range 180-330K were determined. The temperature dependent frequency of the boson peak was then expressed in terms of the mean-square amplitude of the shear modulus fluctuations. This was done using the heterogeneous elasticity theory in combination with the perturbation theory on small fluctuations and Ioffe-Regel criterion for transverse vibrations in glass formers. The contribution of structural relaxation effects to phonon damping becomes significant with increasing temperature. It is shown here that structural relaxation largely determines the temperature dependence of the mean-square fluctuations of the shear modulus at high temperatures. By solving the inverse problem, the temperature dependence of shear modulus fluctuations was obtained. It shows a rapid decrease above ∼250K with a linear extrapolation going to zero at the so-called Arrhenius temperature TA = 350K. Comparison with literature data on the Landau-Placzek ratio shows that they have a similar temperature dependence at T < TA, which is explained by the appearance of nanometer scale spatial heterogeneities below TA. This is confirmed by the temperature dependence of the amplitude of the boson peak.

A Spectral Precursor Indicative of Artificial Water Reservoir-Induced Seismicity: Observations from the Xiangjiaba Reservoir, Southwestern China

Spectral analysis is an effective tool for processing seismic signals, particularly when time-domain characteristics are challenging to capture. In this study, we developed a method using P-wave signals to calculate the power spectrum, enabling the estimation of two spectral parameters—peak frequency and shape factor—for earthquakes recorded by regional seismic networks in the Xiangjiaba (XJB) reservoir area from 2010 to 2015. The temporal evolution of the two spectral parameters was analyzed, revealing that the mean values of individual spectral parameters remain relatively stable despite variations in reservoir water levels. However, a notable increase in the ratio of the shape factor to the peak frequency is observed when the XJB reservoir reaches its maximum water level, suggesting its potential as a precursor indicator for reservoir-induced seismicity (RIS). Furthermore, we performed spatial interpolation on the spectral parameters, and the results show that reservoir impoundment significantly influences the spatial distribution of these parameters. In addition, several regions between the two faults in the tail section of the XJB reservoir exhibit an elevation in the proposed precursor indicator. This study presents a new approach for monitoring and early warning of RIS.

Imaging buried anticlines in the Po Plain, northern Italy, based on HVSR frequency and amplitude analyses

AbstractThe use of the HVSR (Horizontal-to-Vertical Spectral Ratio) method on single-station microtremor measurements is well documented in small alluvial plains for bedrock mapping. In large sedimentary basins, like the Po Plain, its application is still debated. To shed some light on this issue, we investigated two seismogenic structures buried below the Po Plain Quaternary deposits: the Mirandola and Casaglia anticlines. We acquired and analysed a dense distribution of HVSR data covering the two areas and mapped the frequency and amplitude values of the observed resonance peaks. The top of both anticlines is highlighted by high amplitude peaks picturing E-W elongated sectors with high-impedance contrast, where Quaternary deposits are reduced in thickness to about 60–130 m and directly overlay the Pliocene (Mirandola) and Miocene (Casaglia) marine units. In Mirandola, the high-amplitude peaks also correspond to higher resonance frequencies, while in Casaglia, the distribution of resonance frequencies is relatively uniform suggesting a flatter crestal region and the lateral continuity of the resonance surface. The combination of peak frequency and amplitude information on a dense grid of measurement points is thus confirmed to be useful for identifying and mapping buried geological structures such as structural highs. Further modelling is being carried out to estimate the depth of the surface responsible for the observed resonances, through calibration with borehole information. Graphical Abstract

Oecanthus buxixu sp. nov. (Orthoptera: Grylloidea: Oecanthidae): A new species of tree cricket from Brazilian Amazon rainforest

The Tree Crickets of the genus Oecanthus Serville, 1831 are distributed across tropical and temperate regions, where they can be found in all strata of vegetation. In this work, we describe a new species of tree cricket from the Brazilian Amazon rainforest, where only one species was known until the date of this publication. This new species differs from the other 79 species in this genus by the absence of marks on the scape and pedicel of the antennae, as well as by its calling song composed of 3 to 5 chirps/s, 6 to 20 pulses per chirp, and peak frequency 3 to 3.3 kHz, at 26ºC. Photos in vivo of the individuals, as well as images of the metanotal glands and phallic sclerites, are provided.

Quantitatively assessed blood leukocyte Epstein–Barr virus in adult HIV-infected patients

Coinfection with the human immunodeficiency virus (HIV) and Epstein–Barr virus (EBV) represents a current biomedical problem. The purpose of the study was to evaluate blood leukocyte EBV detection rate and viral load in adult HIV-infected patients. Materials and methods. There were examined blood leukocytes collected from 138 HIV(+) and 68 HIV(–) individuals aged 20–69 years. Statistical analysis was carried out differentiated according to the stages of HIV infection, the CD4+ T-lymphocyte count, and adherence to antiretroviral therapy. Results. It was shown that EBV DNA was detected significantly more often in HIV(+) vs HIV(–) individuals (70.3±3.9% and 48.5±6.1%, p = 0.008), with EBV viral load comprising 18 [5; 139] versus 2 [1; 3] copies/105 cells (р 0.001), respectively. It has been shown that the group of HIV(+) patients is heterogeneous in the frequency of EBV detection and viral load, with the peak EBV frequency (86.7±6.2%) and DNA (121 [34; 252] copies/105 cells) level observed in “naive” patients with severe immunodeficiency. Among “experienced” patients receiving therapy, the relative risk of detecting EBV DNA with low treatment adherence was significantly higher compared to those who developed high adherence (р 0.05). When the HIV viral load reached undetectable level, EBV DNA concentration was significantly lower where HIV RNA was detectable (1 [0; 8] versus 15 [1; 162] copies/105 cells, р 0.001). Detection of EBV DNA is associated with higher HIV viral load level and lower CD4+ T-lymphocyte count compared to patients with undetected EBV DNA. A relationship has been established between the CD4+ T-lymphocyte count in HIV(+) patients and the likelihood of active EBV infection. A threshold cut-off of 200 cells/μl was determined. CD4+ T-lymphocyte count 200 cells/μl vs ≥ 200 cells/μl (р 0.001) is associated with a 3.3-fold higher risk of detecting active EBV infection. Conclusion. It is necessary to continue interdisciplinary research to improve early diagnostics of EBV-associated diseases in HIV-infected individuals.

Research on data analysis method of oscillating water column wave energy converters

Abstract Taking the floating oscillating water column central tube wave energy converters (OWC WECs) as the research goal, the Fourier transform (FFT), and the ensemble empirical mode decomposition method (EEMD) were used to statistically analyze the wave height, motion acceleration, velocity and displacement of the device in the physical model test from the perspective of a frequency domain. Through the Fourier transform, the energy spectrum of the incident wave and the motion of the WEC is obtained, and it is found that the peak frequency of the two is the same, that is, the period is 1.138s, but the peak energy of the former is slightly greater than that of the latter. Through the ensemble empirical mode decomposition method, the 1-8 intrinsic mode functions of the incident wave and the displacement of the device are obtained, which shows that the device efficiently captures the dominant frequency wave in the incident wave, that is, the wave height is 0.0628m, the period is 1.1s, and the motion displacement of the vertical direction obtained by the device is 0.0585mm, and the period is 1.1119s. At the same time, it absorbs low-frequency, long-period reflected waves in the pool. The analysis results of the two methods are highly consistent, and the OWC WEC shows good hydrodynamic performance, with efficient wave trapping ability and fast wave responsability. This paper’s research methods and results provide a basis for the later optimization of the device and a new idea for the data processing method of the WECs.

Statistical Distribution of the Peak Frequency of ECH Waves in the Outer Magnetosphere From Magnetospheric Multiscale Satellite Observations

AbstractElectron cyclotron harmonic (ECH) waves are electrostatic emissions with frequencies between the harmonics of the electron gyrofrequencies. Their frequency properties provide clues for understanding their generation and are keys to evaluating their scattering efficiency. Based on Magnetospheric Multiscale satellite observations, we explored the statistical frequency properties of first‐harmonic band ECH waves in the outer magnetosphere. The frequencies at the peak power of ECH waves are found to be day‐night and dawn‐dusk asymmetries, with higher values in the regions from dawn to post‐noon, and these asymmetries are more evident during weaker geomagnetic activity. Furthermore, the frequencies at the peak power of ECH waves decrease gradually with increasing |MLAT| and are positively correlated with their amplitudes at each magnetic local time or |MLAT|. Information on the frequency properties of ECH waves presented in this study can be crucial for future modeling of their contributions to magnetospheric electron dynamics.

Flood Potential Portal: A web tool for understanding flood variability and predicting peak discharges

AbstractThe Flood Potential Portal (https://floodpotential.erams.com/) has been developed for the contiguous United States, as a practitioner‐focused tool that uses observational data (streamgages) to enhance understanding of how floods vary in space and time, and assist users in making more informed peak discharge predictions for infrastructure design and floodplain management. This capability is presented through several modules. The Mapping module provides tools to explore variability using multiple indices, and provides detailed information, figures, and algorithms describing and comparing flooding characteristics. The Cross‐Section Analysis module allows users to cut regional‐scale sections to interpret the role of topography in driving flood variability. The Watershed Analysis module provides multiple methods for quantifying expected peak discharge magnitudes and flood frequency relationships at user‐selected locations, including the integration of observed trends in flood magnitudes due to climate change and other sources of nonstationarity into decision making. The Streamgage Analysis module performs streamgage flood‐frequency analyses. These modules are based in part on the flood potential method, through the use of 207 zones of similar flood response defined using more than 8200 streamgages with watershed areas &lt;10,000 km2. Regression models that define each zone had high explained variance (average R2 = 0.93). An example is provided to illustrate use of the Flood Potential Portal for the design of a hypothetical bridge replacement.

Scalar induced gravitational waves in chiral scalar–tensor theory of gravity

We study the scalar induced gravitational waves (SIGWs) from a chiral scalar–tensor theory of gravity. The parity-violating (PV) Lagrangian contains the Chern–Simons (CS) term and PV scalar–tensor terms, which are built of the quadratic Riemann tensor term and first-order derivatives of a scalar field. We consider SIGWs in two cases, in which the semi-analytic expression to calculate SIGWs can be obtained. Then, we calculate the fractional energy density of SIGWs with a monochromatic power spectrum for the curvature perturbation. We find that the SIGWs in chiral scalar–tensor gravity behave differently from those in GR before and after the peak frequency, which results in a large degree of circular polarization.

A Reduction in the Rotational Velocity Measurement Deviation of the Vortex Beam Superposition State for Tilted Object

In measuring object rotational velocity using vortex beam, the incident light on a tilted object causes spectral broadening, which significantly interferes with the identification of the true rotational Doppler shift (RDS) peak. We employed a velocity decomposition method to analyze the relationship between the spectral extremum and the central frequency shift caused by the object tilt. Compared with the linear growth trend observed when calculating the object rotational velocity using the frequency peak with the maximum amplitude, the central frequency calculation method effectively reduced the deviation rate of the RDS and velocity measurement value from the true value, even at large tilt angles. This approach increased the maximum tilt angle for a 1% relative error from 0.221 to 0.287 rad, representing a 29.9% improvement. When the tilt angle was 0.7 rad, the velocity measurement deviation reduction rate can reach 5.85%. Our work provides crucial support for achieving high-precision rotational velocity measurement of tilted object.

Deep learning image reconstruction for low-kiloelectron volt virtual monoenergetic images in abdominal dual-energy CT: medium strength provides higher lesion conspicuity.

The best settings of deep learning image reconstruction (DLIR) algorithm for abdominal low-kiloelectron volt (keV) virtual monoenergetic imaging (VMI) have not been determined. To determine the optimal settings of the DLIR algorithm for abdominal low-keV VMI. The portal-venous phase computed tomography (CT) scans of 109 participants with 152 lesions were reconstructed into four image series: VMI at 50 keV using adaptive statistical iterative reconstruction (Asir-V) at 50% blending (AV-50); and VMI at 40 keV using AV-50 and DLIR at medium (DLIR-M) and high strength (DLIR-H). The signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR) of nine anatomical sites were calculated. Noise power spectrum (NPS) using homogenous region of liver, and edge rise slope (ERS) at five edges were measured. Five radiologists rated image quality and diagnostic acceptability, and evaluated the lesion conspicuity. The SNR and CNR values, and noise and noise peak in NPS measurements, were significantly lower in DLIR images than AV-50 images in all anatomical sites (all P < 0.001). The ERS values were significantly higher in 40-keV images than 50-keV images at all edges (all P < 0.001). The differences of the peak and average spatial frequency among the four reconstruction algorithms were significant but relatively small. The 40-keV images were rated higher with DLIR-M than DLIR-H for diagnostic acceptance (P < 0.001) and lesion conspicuity (P = 0.010). DLIR provides lower noise, higher sharpness, and more natural texture to allow 40 keV to be a new standard for routine VMI reconstruction for the abdomen and DLIR-M gains higher diagnostic acceptance and lesion conspicuity rating than DLIR-H.

Ensemble Feature Selection for Clustering Damage Modes in Carbon Fiber‐Reinforced Polymer Sandwich Composites Using Acoustic Emission

Acoustic emission (AE) serves as a noninvasive technique for real‐time structural health monitoring, capturing the stress waves produced by the formation and growth of cracks within a material. This study presents a novel ensemble feature selection methodology to rank features highly relevant with damage modes in AE signals gathered from edgewise compression tests on honeycomb‐core carbon fiber‐reinforced polymer. Two distinct features, amplitude and peak frequency, are selected for labeling the AE signals. An ensemble‐supervised feature selection method ranks feature importance according to these labels. Using the ranking list, unsupervised clustering models are then applied to identify damage modes. The comparative results reveal a robust correlation between the damage modes and the features of counts and energy when amplitude is selected. Similarly, when peak frequency is chosen, a significant association is observed between the damage modes and the features of partial powers 1 and 2. These findings demonstrate that, in addition to the commonly used features, other features, such as partial powers, exhibit a correlation with damage modes.

Development of a characterization method for high-speed vehicle-induced vibrations in the built environment

A methodology was developed to analyze vehicle-induced vibration on street-adjacent structures. In partnership with an international racing organization, acceleration data was recorded during vehicle pass-by events during measurement campaigns at three locations involving cars traveling at high-speed. Net peak particle velocities were then calculated from the acceleration data. A unique filtering approach was developed for removing non-vehicle-induced signal noise from the measured data prior to analysis. Finally, an adaptation of the frequency domain composition (FDD) method was used to identify peak frequencies of interest for each event. By comparing the processed data to existing standards for cosmetic damage in buildings, the level of structural excitation caused by the measured vehicles was able to be assessed.

Design and analysis of Minkowski fractal shaped metasurface absorber with broadband and polarization-insensitive characteristics using a tunable graphene layer for terahertz applications

The proposed research article’s main goal is to demonstrate a terahertz (THz) broadband absorber for high-speed wireless communication applications. The proposed structure is a compact one and possesses three layers. The ground layer acts as a metal reflector, lossy silicon acts as a dielectric material and finally a graphene layer in the shape of a minkowski fractal acts as a radiating patch for the proposed design. We have chosen a thickness of 5 μm for the lossy silicon which has a dielectric constant of 11.90. The bottom layer of the proposed design contains a good conductive material like gold with a conductivity of 4.561 e+007 s m−1 with a thickness of 0.2 μm. The thickness of a monolayer graphene is one nanometer, and the overall unit cell size of the proposed structure is 12 × 12 μm2. Because of its symmetrical nature, the proposed absorber offers a broad response to both TM and TE modes irrespective of any polarization angle. The proposed absorber can operate in the terahertz frequency range and has achieved two broad frequency bands from 3.34–3.98 THz and 4.6–5.30 THz, with an absorption percentage greater than 90. We can observe peak absorption frequencies at 3.60 THz and 5.04 THz, which exhibit an absorption percentage close to unity. Additionally, we validated the proposed broadband absorber using an equivalent circuit approach and verified it using the ADS tool.

Fluid resonance in narrow gaps formed by three-box system with sharp and round edge profiles under irregular wave actions

Fluid resonance within narrow gaps in multiple-box systems with sharp and round edge profiles under irregular wave actions are investigated by using a viscous fluid flow solver based on OpenFOAM® package. In difference to the two-peak behavior under regular wave actions, the variation of free surface amplitudes in narrow gaps with incident spectral peak frequencies show the single-peak behavior, including the sharp and round edge profiles. Spectral analysis indicates that the wave spectrums of fluid oscillations in narrow gaps mainly around the first- and/or second-order resonant frequencies. The second-order fluid resonance is easier to be aroused for round edge profiles than that for sharp edge profiles. Furthermore, the statistical and histogram results indicate the significant periods are always around the resonant frequencies; while the corresponding standard deviations approach to cover the region between two resonant frequencies. The above results confirm that the wave responses in narrow gaps mainly oscillate with two resonant frequencies under irregular wave actions.

Investigation on the damage mechanisms using acoustic emission method and damping characteristics of hybrid flax‐glass composites

AbstractFiber‐reinforced polymers (FRP) feature high strength‐to‐weight ratio amongst the emerging class of natural composites. This paper presents the impact of the glass fiber on the tensile strength of the flax epoxy laminate. The mechanical behavior and damping characteristics of flax fiber reinforced polymer (FFRP) and the hybrid flax‐glass fiber reinforced polymer (HFRP) are experimentally investigated. Both the flax and hybrid FRPs are made using vacuum infusion process. The specimens without and with holes of 4, 5, and 6 mm in diameter are subjected to tensile test using acoustic emission monitoring and free vibration test. In the former testing, HFRP resulted in higher peak frequencies and cumulative counts. Also, the natural frequency and damping factor of HFRP vary proportionately with the hole size, as identified in the latter tests. Different damage mechanisms during the tensile test revealed that the presence of glass fibers in HFRP increased resistance for certain damage mechanisms.Highlights Adding glass fiber to flax fiber reinforced polymer (FFRP) creates a hybrid FRP (HFRP) with increased resistance to damage and improved damping characteristics. HFRP exhibits a distinction in failure mechanisms compared to FFRP. The study utilizes acoustic emission (AE) to identify various damage mechanisms in the material, providing a more detailed information. The addition of glass fibers in HFRP leads to a more pronounced increase in damping factors.

Investigation on the damage mechanisms using acoustic emission method and damping characteristics of hybrid flax‐glass composites

AbstractFiber‐reinforced polymers (FRP) feature high strength‐to‐weight ratio amongst the emerging class of natural composites. This paper presents the impact of the glass fiber on the tensile strength of the flax epoxy laminate. The mechanical behavior and damping characteristics of flax fiber reinforced polymer (FFRP) and the hybrid flax‐glass fiber reinforced polymer (HFRP) are experimentally investigated. Both the flax and hybrid FRPs are made using vacuum infusion process. The specimens without and with holes of 4, 5, and 6 mm in diameter are subjected to tensile test using acoustic emission monitoring and free vibration test. In the former testing, HFRP resulted in higher peak frequencies and cumulative counts. Also, the natural frequency and damping factor of HFRP vary proportionately with the hole size, as identified in the latter tests. Different damage mechanisms during the tensile test revealed that the presence of glass fibers in HFRP increased resistance for certain damage mechanisms.Highlights Adding glass fiber to flax fiber reinforced polymer (FFRP) creates a hybrid FRP (HFRP) with increased resistance to damage and improved damping characteristics. HFRP exhibits a distinction in failure mechanisms compared to FFRP. The study utilizes acoustic emission (AE) to identify various damage mechanisms in the material, providing a more detailed information. The addition of glass fibers in HFRP leads to a more pronounced increase in damping factors.

Performance Evaluation and Comparative Analyses of Tuned Inerter Damper for Stochastic Base Excited Structures Based on Hybrid H2/H∞ Optimization

Compared with tuned mass damper, tuned inerter damper (TID) has higher damping efficiency and lightweight characteristic if appropriate optimal methods are selected. Generally, [Formula: see text] or [Formula: see text] optimal methods are adopted to determine the optimal parameters of TID individually. But the vibration mitigation performance of the TID under near resonance frequency band based on [Formula: see text] optimization is less than [Formula: see text] optimization, but the peak frequency response based on [Formula: see text] optimization will be greater than [Formula: see text] optimization at the same time. Dual-characteristic-based vibration control may not be achievable based on [Formula: see text] or [Formula: see text] criteria, respectively. For this reason, hybrid [Formula: see text] optimization can be adopted. In this work, closed-form expressions are derived for the control of structural displacement responses based on hybrid [Formula: see text] optimal method. The vibration mitigation performance of the different optimized TIDs is evaluated considering the single-degree-of-freedom and multi-degrees-of-freedom systems are subjected to typical ground motions excitation. Results illustrate that because of the use of the optimal stiffness ratio of [Formula: see text] optimization and very close value of [Formula: see text] optimizations’ nominal damping ratio in [Formula: see text] optimization, [Formula: see text] optimization shows ‘dual characteristics’ in different excitation situations. Specifically, the peak response and structural fundamental frequencies’ response in displacement frequency response function using hybrid [Formula: see text] optimal methods are between [Formula: see text] and [Formula: see text] optimization, which indicates an excellent and balanced control performance combining the advantages of [Formula: see text] and [Formula: see text] optimal solutions. Hence, this hybrid method is more suitable for more complex ground motions excitation to control critical structural responses instead of single characteristic excitation. And the comprehensive vibration control in dynamic time histories analyses can be achieved by this dual characteristic-based optimal strategy. When designing the specific TID, hybrid [Formula: see text] optimization can be considered as the best choice for its compatibility and high adaptability for complex practical engineering scenarios with random and diverse excitations.

Cure State Sensing of Polymethylmethacrylate Using a Vibrating Axial Probe.

A new axially vibrating sensor based on an audio voice coil transducer and a lead zirconate titanate (PZT) piezoelectric disc microphone was developed as a probe for the measurement of in vitro rheological fluid properties, including curing progress for polymethylmethacrylate (PMMA) mixtures with important uses as bone cement in the field of orthopedics. The measurement of the vibrating axial sensor's acoustic spectra in PMMA undergoing curing can be described by a damped harmonic oscillator formalism and resonant frequency (ca. 180 Hz) shift can be used as an indicator of curing progress, with shifts to the blue by as much as 14 Hz. The resonant frequency peak was measured in 19 different 4.0 g PMMA samples to have a rate of shift of 0.0462 ± 0.00624 Hz·s-1 over a period of 400 s while the PMMA was in a dough state and before the PMMA transitioned to a hard-setting phase. This transition is unambiguously indicated by this sensor technology through the generation of a distinct circa 5 kHz high-Q under-damped ring-down response.

Individual posterior alpha rhythms and cognitive reserve as possible early prognostic markers in people with subjective memory complaints

Subjective memory complaints (SMCs) are a memory disorder that often precedes mild cognitive impairment (MCI) or Alzheimer’s disease (AD). Both individual alpha rhythms and cognitive reserve (CR) represent key features of SMCs and provide useful tools to characterize and predict the course of the disorder. We studied whether older people with SMCs may also present some abnormal resting state electroencephalogram (rsEEG) alpha rhythms, and whether alpha rhythms are associated with CR. To do this, eyes-closed rsEEG were recorded in 68 older people with and without SMCs. The individual alpha indexes alpha/theta transition frequency (TF) and individual alpha frequency peak (IAFp) were computed. TF and IAFp were also used to determine the alpha1, alpha2, and alpha3 power frequency. Results indicated no differences in TF or IAFp between older people with SMCs and controls. The SMCs group showed a reduction in alpha3 power in comparison with controls. Specifically, women with SMCs were characterized by a significant decrease in alpha3 power compared to control women. Furthermore, only in SMCs group, greater CR was associated with slow IAFp. In sum, these results suggest that TF and IAFp are two stable indexes that are not influenced by the presence of SMCs. However, the reduction in alpha3, as observed in women with SMCs, shows an abnormal posterior rsEEG at alpha power. Finally, the compensatory mechanisms of CR appear to interact with the neurophysiological mechanisms that underlie the regulation of alpha rhythms.