Peak External Quantum Efficiency Research Articles

Solvent-Reconstructed Interface That Enhances Light Out-Coupling in Quasi-Two-Dimensional Perovskite Light-Emitting Diodes.

Light management is critical to maximizing the external quantum efficiency of perovskite light-emitting diodes (PeLEDs), but strategies for enhancing light out-coupling are typically complex and expensive. Here, using a facile solvent treatment strategy, we create a layer of lithium fluoride (LiF) nanoislands that serve as a template to reconstruct the light-extracting interfaces for PeLEDs. The nanoisland interface rearranges the near-field light distribution in order to maximize the efficiency of internal light extraction. With the proper adjustment of the nanoisland size and distribution, we have achieved an optimal balance between charge injection and light out-coupling, resulting in bright, pure-red quasi-two-dimensional PeLEDs with a 21.8% peak external quantum efficiency.

The synergy of pre-frozen substrates and post-annealing for high-efficiency co-evaporated blue perovskite LEDs

The co-evaporation technique shows great potential for producing perovskite films. However, there is a lack of research on the growth process and the film characteristics of co-evaporated perovskite. Herein, we found that pre-frozen substrates and post-annealing can synergically improve the performance of co-evaporated blue perovskite light-emitting diodes (PeLEDs). The optimized blue PeLEDs obtained an impressive peak external quantum efficiency (EQE) of 7.2%, which is the best reported for co-evaporated blue PeLEDs till now. The systematic investigation found that the pre-frozen substrates can facilitate the exotherm of vaporized precursor molecules near the interface, leading to more efficient nucleation and constraining grain enlargement. Furthermore, low-temperature annealing (LTA) can efficiently suppress compositional segregation and release residual compressive strain in co-evaporated perovskite films while retaining the advantages of pre-frozen substrates. This work provided deeper insights into perovskite films prepared by co-evaporation and offered a feasible strategy for enhancing the performance of the co-evaporated PeLEDs.

Acceleration of radiative recombination for efficient perovskite LEDs

The increasing demands for more efficient and brighter thin-film light-emitting diodes (LEDs) in flat-panel display and solid-state lighting applications have promoted research into three-dimensional (3D) perovskites. These materials exhibit high charge mobilities and low quantum efficiency droop1–6, making them promising candidates for achieving efficient LEDs with enhanced brightness. To improve the efficiency of LEDs, it is crucial to minimize nonradiative recombination while promoting radiative recombination. Various passivation strategies have been used to reduce defect densities in 3D perovskite films, approaching levels close to those of single crystals3. However, the slow radiative (bimolecular) recombination has limited the photoluminescence quantum efficiencies (PLQEs) of 3D perovskites to less than 80% (refs. 1,3), resulting in external quantum efficiencies (EQEs) of LED devices of less than 25%. Here we present a dual-additive crystallization method that enables the formation of highly efficient 3D perovskites, achieving an exceptional PLQE of 96%. This approach promotes the formation of tetragonal FAPbI3 perovskite, known for its high exciton binding energy, which effectively accelerates the radiative recombination. As a result, we achieve perovskite LEDs with a record peak EQE of 32.0%, with the efficiency remaining greater than 30.0% even at a high current density of 100 mA cm−2. These findings provide valuable insights for advancing the development of high-efficiency and high-brightness perovskite LEDs.

Etching-free pixel definition in InGaN green micro-LEDs

The traditional plasma etching process for defining micro-LED pixels could lead to significant sidewall damage. Defects near sidewall regions act as non-radiative recombination centers and paths for current leakage, significantly deteriorating device performance. In this study, we demonstrated a novel selective thermal oxidation (STO) method that allowed pixel definition without undergoing plasma damage and subsequent dielectric passivation. Thermal annealing in ambient air oxidized and reshaped the LED structure, such as p-layers and InGaN/GaN multiple quantum wells. Simultaneously, the pixel areas beneath the pre-deposited SiO2 layer were selectively and effectively protected. It was demonstrated that prolonged thermal annealing time enhanced the insulating properties of the oxide, significantly reducing LED leakage current. Furthermore, applying a thicker SiO2 protective layer minimized device resistance and boosted device efficiency effectively. Utilizing the STO method, InGaN green micro-LED arrays with 50-, 30-, and 10-µm pixel sizes were manufactured and characterized. The results indicated that after 4 h of air annealing and with a 3.5-μm SiO2 protective layer, the 10-µm pixel array exhibited leakage currents density 1.2 × 10−6 A/cm2 at −10 V voltage and a peak on-wafer external quantum efficiency of ~6.48%. This work suggests that the STO method could become an effective approach for future micro-LED manufacturing to mitigate adverse LED efficiency size effects due to the plasma etching and improve device efficiency. Micro-LEDs fabricated through the STO method can be applied to micro-displays, visible light communication, and optical interconnect-based memories. Almost planar pixel geometry will provide more possibilities for the monolithic integration of driving circuits with micro-LEDs. Moreover, the STO method is not limited to micro-LED fabrication and can be extended to design other III-nitride devices, such as photodetectors, laser diodes, high-electron-mobility transistors, and Schottky barrier diodes.

Synergistic Modulation of Excited State Ingredients and Chiroptical Activity for High‐Performance Pure‐Green Circularly Polarized Electroluminescence

Synergistic Modulation of Excited State Ingredients and Chiroptical Activity for High‐Performance Pure‐Green Circularly Polarized Electroluminescence

UV‐A/B High‐Sensitivity Organic Photodetectors Containing Butterfly‐Shaped Furan‐Fused BN‐Dihydropyrene with Push‐Pull Electron “Wings” toward Image Sensor

AbstractReplacement of C─C unit with its isoelectronic B─N unit in aromatics provides a new class of molecules with appealing properties. Herein, Five novel butterfly‐shaped furan‐fused bis‐BN dihydropyrenes (FBN) derivatives are synthesized with different push‐pull electron “wings”. These compounds exhibit prominent UV‐A/B absorption, high energy levels, and p‐type characteristics. Thanks to the side‐chain engineering and BN dipole manipulation, their intramolecular dipole moments and intermolecular stacking mode are effectively regulated to improve intra‐ and inter‐molecular charge transfer, thus achieving high hole mobilities. Five FBN‐X compounds are doped with PC71BM as heterojunction photosensitive layers to fabricate solution‐processed high performance organic photodetectors (OPDs), which exhibit self‐powered effect and high sensitivity to UV‐A/B. Especially, the FBN‐CN‐based device presents a high detectivity up to 1.72 × 1012 Jones, a peak external quantum efficiency of 19.1%, and an extremely low dark current density of 8.90 × 10−10 A cm−2 under 320 nm at 0 V. To the best of authors knowledge, it is the first report of photodiode‐type UV‐OPDs containing BN‐doped polycyclic aromatic hydrocarbons as active layer to date. And the optimal device shows a significant advantage over the reported 300–380 nm UV‐OPDs. In addition, a 10 × 10 array of organic image sensor is successfully demonstrated, which showcases excellent low‐light imaging capability.

Quantum‐Dots Matrix Encapsulated CsPbI3 Polycrystal Composite Films for Efficient and Bright Deep‐Red Light‐Emitting Diodes

AbstractAll‐inorganic CsPbI3 perovskite is a promising emitter for deep‐red light‐emitting diodes (LEDs). However, presently fabricated CsPbI3 polycrystalline films are composed of island‐like polycrystals, encountering the problems of serious interface current leakage and low‐efficiency carrier radiative recombination. Here, a CsPbI3‐xBrx quantum dots (QDs) matrix encapsulated CsPbI3 polycrystal film is reported to address the low‐efficiency issue of island‐like CsPbI3 polycrystalline film applied in deep‐red LEDs. The developed QDs matrix encapsulation strategy has two benefits. One is the filling of void space in the island‐like CsPbI3 polycrystal film to suppress the interface current leakage. The other more important benefit is utilizing the strong carrier confinement effect of QDs to strengthen the formation of excitons in the composite film and thus improve the electroluminescence efficiency. Moreover, interesting grain growth is found between CsPbI3‐xBrx QDs and CsPbI3 polycrystals, which further enhances the exciton transfer effect brought by the QDs matrix and optoelectronic properties of the fabricated composite films. Based on the obtained high‐quality QDs/polycrystal composite films, efficient and bright deep‐red LEDs are achieved with a peak external quantum efficiency of 15.24% and a maximum luminance of 3691 cd m−2.

Efficient Charge Injection for Perovskite Light‐Emitting Transistor

AbstractMetal halide perovskite semiconductors have demonstrated remarkable performance in light‐emitting‐diode applications in recent years. However, their potential application in other emerging optoelectronic devices, such as light‐emitting field‐effect transistors (LEFETs) is impeded by poor luminous efficiency due to inefficient charge injection. Here, an n‐type MgZnInO (MIZO) as the channel layer is synthesized to achieve efficient electron injection in perovskite LEFETs. These findings indicate that the incorporation of Mg not only suppresses the generation of oxygen vacancies but also optimizes the energy level alignment. These synergistic effects reduce non‐radiative recombination and improve interfacial charge transport. Consequently, the MIZO‐based perovskite LEFETs exhibit an improvement in threshold voltage, subthreshold swing, and field‐effect mobility. The electroluminescence performance shows a peak external quantum efficiency (EQE) of 1.97% with a maximum brightness of 2.1 × 104 cd m−2, accompanied by low‐efficiency roll‐off (an EQE of 1.88% at the current density of 810 mA cm−2). To the best of the author's knowledge, this represents the best luminous efficiency reported for perovskite LEFETs to date.

High Efficiency of 5 μm‐Diameter Blue Micro‐Light‐Emitting Diodes

Small‐size pixels and high efficiency under low injection levels are required for high‐resolution microdisplay. Efficient blue InGaN micro‐light‐emitting diodes (μLEDs) with 5 μm diameter are fabricated using AuSn flip‐chip bonding, high reflection electrodes, and large‐area N electrodes surrounding the mesas. The peak external quantum efficiency (EQE) measured in an integrating sphere is as high as 13.67% at a current density of 5.4 A cm−2. Moreover, at a current density of 0.1 A cm−2, EQE can still reach 11.69%. The electrical efficiency approaches 1, and the differential slope of log L versus log I is close to 1 at low current density. These results suggest significant progress in exploring high‐efficiency 5 μm InGaN blue μLEDs.

Multifunctional Ionic‐Ligand Regulated High‐Quality γ‐CsPbI3 Thin Films for Efficient and Bright Deep‐Red Light‐Emitting Diodes

AbstractAll‐inorganic CsPbI3 perovskite semiconductor is attractive for deep‐red light‐emitting diodes (LEDs) because of its high photoluminescence, good thermal stability, excellent charge transport, and solution processability. However, the metastable phase of optically active CsPbI3 hinders the fabrication of efficient and bright deep‐red LEDs. Herein, a multifunctional ionic ligand regulation strategy using (2‐hydroxy‐5‐methylphenyl) triphenyl‐phosphonium iodide and 3‐(N, N‐dimethyloctylammonio) propanesulfonate is reported to regulate the optically active CsPbI3 crystallization and thus obtain high‐quality γ‐CsPbI3 thin films. The high crystallinity and preferential orientation of γ‐CsPbI3 arise from the strong bonding between the ionic ligands and ionic lead halide clusters. The obtained γ‐CsPbI3 thin films also possess suppressed defect densities, high luminescence, and high stability. Using this high‐quality thin film, an efficient and bright deep‐red LED with a peak external quantum efficiency of 13.34% and a maximum luminance of 2110 cd m−2 is successfully fabricated. The operational lifetime of the fabricated LED (time to half of the initial brightness, T50) reaches up to 40 min under a high current density of 50 mA cm−2 (corresponding to the initial brightness of 200 cd m−2).

Modulation of Nucleation and Growth Kinetics of Perovskite Nanocrystals Enables Efficient and Spectrally Stable Pure-Red Light-Emitting Diodes.

Perovskite light-emitting diodes (PeLEDs) based on CsPb(Br/I)3 nanocrystals (NCs) usually suffer from severe spectral instability under operating voltage due to the poor-quality PeNCs. Herein, zeolite was utilized to prepare high-quality CsPb(Br/I)3 NCs via promoting the homogeneous nucleation and growth and suppressing the Ostwald ripening of PeNCs. In addition, the decomposed zeolite interacted strongly with PeNCs through Pb-O bonds and hydrogen bonds, which inhibited the formation of defects and suppressed halide ion migration, leading to an improved photoluminescence quantum yield (PLQY) and enhanced stability of PeNCs. Moreover, the strong binding affinity of decomposed zeolite to PeNCs contributed to the formation of homogeneous perovskite films with high PLQY. As a result, pure-red PeLEDs with Commission International de I'Eclairage (CIE) coordinates of (0.705, 0.291) were fabricated, approaching the Rec. 2020 red primary color. The devices achieved a peak external quantum efficiency of 23.0% and outstanding spectral stability.

Nanosurface-reconstructed perovskite for highly efficient and stable active-matrix light-emitting diode display.

Perovskite quantum dots (QDs) are promising for various photonic applications due to their high colour purity, tunable optoelectronic properties and excellent solution processability. Surface features impact their optoelectronic properties, and surface defects remain a major obstacle to progress. Here we develop a strategy utilizing diisooctylphosphinic acid-mediated synthesis combined with hydriodic acid-etching-driven nanosurface reconstruction to stabilize CsPbI3 QDs. Diisooctylphosphinic acid strongly adsorbs to the QDs and increases the formation energy of halide vacancies, enabling nanosurface reconstruction. The QD film with nanosurface reconstruction shows enhanced phase stability, improved photoluminescence endurance under thermal stress and electric field conditions, and a higher activation energy for ion migration. Consequently, we demonstrate perovskite light-emitting diodes (LEDs) that feature an electroluminescence peak at 644 nm. These LEDs achieve an external quantum efficiency of 28.5% and an operational half-lifetime surpassing 30 h at an initial luminance of 100 cd m-2, marking a tenfold improvement over previously published studies. The integration of these high-performance LEDs with specifically designed thin-film transistor circuits enables the demonstration of solution-processed active-matrix perovskite displays that show a peak external quantum efficiency of 23.6% at a display brightness of 300 cd m-2. This work showcases nanosurface reconstruction as a pivotal pathway towards high-performance QD-based optoelectronic devices.

Efficient and bright broadband electroluminescence based on environment-friendly metal halide nanoclusters

Broadband electroluminescence based on environment-friendly emitters is promising for healthy lighting yet remains an unprecedented challenge to progress. The copper halide-based emitters are competitive candidates for broadband emission, but their high-performance electroluminescence shows inadequate broad emission bandwidth of less than 90 nm. Here, we demonstrate efficient ultra-broadband electroluminescence from a copper halide (CuI) nanocluster single emitter prepared by a one-step solution synthesis-deposition process, through dedicated design of ligands and subtle selection of solvents. The CuI nanocluster exhibits high rigidity in the excitation state as well as dual-emissive modes of phosphorescence and temperature-activated delayed fluorescence, enabling the uniform cluster-composed film to show excellent stability and high photoluminescent efficiency. In consequence, ultra-broadband light-emitting diodes (LEDs) present nearly identical performance in an inert or air atmosphere without encapsulation and outstanding high-temperature operation performance, reaching an emission full width at half maximum (FWHM) of ~120 nm, a peak external quantum efficiency of 13%, a record maximum luminance of ~50,000 cd m−2, and an operating half-lifetime of 137 h at 100 cd m−2. The results highlight the potential of copper halide nanoclusters for next-generation healthy lighting.

Efficient non-doped cluster light-emitting diodes based on semiconducting copper iodide hybrids

Copper iodide hybrid clusters have attracted lots of interest in solution-processed light-emitting diodes (LEDs) for solid-state lighting and display in recent years, benefiting from their simple synthesis, structural diversity, high photoluminescence quantum yield (PLQY), and non-toxicity. However, most efficient copper iodide cluster LEDs are made by host-guest doped emitters and thus suffer from cumbersome synthesis and increased costs from the expensive hosts. Here, we report a non-doped cluster LED based on a novel copper iodine hybrid [35DPPy]4Cu2I2 (35DPPy: 3,5-diphenylpyridine) with high PLQY and decent charge transport characteristic. The non-doped [35DPPy]4Cu2I2 film synthesized by a one-step spin-coating approach possess the flat and compact morphology, high PLQY of 59.6%, and excellent heat/ultraviolet (UV) light/moisture/oxygen stability. The efficient green PL of [35DPPy]4Cu2I2 is proved to originate from the synergistic contribution from thermally activated delayed fluorescence and phosphorescence. A non-doped green LED based on [35DPPy]4Cu2I2 emitters is fabricated, achieving a peak external quantum efficiency of 4.8% and a maximum luminance of 3895 cd/m2. More importantly, large-area LEDs with an emitting area of 4.00 cm2 are realized with homogeneous and bright electroluminescence, showing their attractive potentials as novel electroluminescent emitters in the application of non-doped cluster LEDs.

Controlling Interfacial Amidation Reaction Rate to Regulate Crystal Growth toward High-Performance FAPbBr3-Based Inverted Light-Emitting Diodes.

Controlling interfacial reactions is critical for zinc oxide (ZnO)-based inverted perovskite light-emitting diodes (PeLEDs), boosting the external quantum efficiency (EQE) of the near-infrared device to above 20%. However, violent interfacial reactions between the bromine-based perovskites and ZnO-based films severely limit the performance of inverted green PeLEDs, whose efficiency and stability lag far behind those of their near-infrared counterparts. Here, a controllable interfacial amidation between the bromine-based perovskites and magnesium-doped ZnO (ZnMgO) film utilizing caprylyl sulfobetaine (SFB) is realized. The SFB molecules strongly interact with formamidinium bromide, decelerating the amidation reaction between formamidinium and carboxylate groups on the ZnMgO film, thus regulating the crystallization of FAPbBr3. Combined with the passivation of benzylamine, a FAPbBr3 bulk film directly deposited on a ZnMgO substrate with single-crystal characteristics is obtained, exhibiting a high photoluminescence quantum yield of above 80%. The resultant PeLEDs demonstrate a peak EQE of exceeding 20% at a high luminance of 120,000 cd m-2 and a half lifetime of 26 min at 11,000 cd m-2, representing the state-of-the-art inverted green electroluminescence. This work resolves the crucial issues of violent interfacial reactions and provides a strategy toward inverted green PeLEDs with outstanding performance.

High-Performance Tandem Quantum-Dot Light-Emitting Diodes Based on Bulk-Heterojunction-Like Charge-Generation Layers.

In this study, the fundamental but previously overlooked factors of charge generation efficiency and light extraction efficiency (LEE) are explored and collaboratively optimized in tandem quantum-dot light-emitting diodes (QLEDs). By spontaneously forming a microstructured interface, a bulk-heterojunction-like charge-generation layer composed of a poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate)/ZnO bilayer is fabricated and an ideal charge-generation efficiency surpassing 115% is obtained. The coupling strength of the waveguide mode for the top unit and the plasmon polariton loss for the bottom unit are highly suppressed using precise thickness control, which increases the LEE of the tandem devices. The red tandem QLED achieves an exceptionally low turn-on voltage for electroluminescence at 4.0V and outstanding peak external quantum efficiency of 42.9%. The ultralow turn-on voltage originates from the sequential electroluminescence turn-on of the two emissive units of the tandem QLED. Benefiting from its unique electroluminescent features, an easily fabricated optical-electrical dual anti-counterfeiting display is built by combining a dichromatic tandem QLED with masking technology.

Elucidating the Role of Ligand Engineering on Local and Macroscopic Charge‐Carrier Transport in NaBiS2 Nanocrystal Thin Films

AbstractTernary chalcogenides have emerged as potential candidates for ultrathin photovoltaics, and NaBiS2 nanocrystals (NCs) have gained appeal because of their months‐long phase‐stability in air, high absorption coefficients >105 cm−1, and a pseudo‐direct bandgap of 1.4 eV. However, previous investigations into NaBiS2 NCs used long‐chain organic ligands separating individual NCs during synthesis, which severely limits macroscopic charge‐carrier transport. In this work, these long‐chain ligands are exchanged for short iodide‐based ligands, allowing to understand the macroscopic charge‐carrier transport properties of NaBiS2 and evaluate its photovoltaic potential in more depth. It is found that ligand exchange results in simultaneous improvements in intra‐NC (microscopic) and inter‐NC (macroscopic) mobilities, while charge‐carrier localization still takes place, which places a fundamental limit on the transport lengths achievable. Despite this limitation, the high absorption coefficients enable ultrathin (55 nm thick) solar absorbers to be used in photovoltaic devices, which have peak external quantum efficiencies > 50%. In addition, temperature‐dependent transient current measurements uncover a small activation energy barrier of 88 meV for ion migration, which accounts for the strongly hysteretic behavior of NaBiS2 photovoltaic devices. This work not only reveals how the charge‐carrier transport properties of NaBiS2 NCs over several length and time scales are influenced by ligand engineering, but also unveils the facile ionic transport in this material, which limits the potential of NaBiS2 in photovoltaics. On the other hand, the discovery shows that there are opportunities to use this material in memristors, electrolytes, and other applications requiring ionic conduction.

Synchronously Polishing the Lead-Rich Surface and Passivating Surface Defects of CsPb(Br/I)3 Quantum Dots for High-Performance Pure-Red PeLEDs.

Mixed-halide CsPb(Br/I)3 perovskite quantum dots (QDs) are regarded as one of the most promising candidates for pure-red perovskite light-emitting diodes (PeLEDs) due to their precise spectral tuning property. However, the lead-rich surface of these QDs usually results in halide ion migration and nonradiative recombination loss, which remains a great challenge for high-performance PeLEDs. To solve the above issues, we employ a chelating agent of 1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetic acid hydrate (DOTA) to polish the lead-rich surface of the QDs and meanwhile introduce a new ligand of 2,3-dimercaptosuccinic acid (DMSA) to passivate surface defects of the QDs. This synchronous post-treatment strategy results in high-quality CsPb(Br/I)3 QDs with suppressed halide ion migration and an improved photoluminescence quantum yield, which enables us to fabricate spectrally stable pure-red PeLEDs with a peak external quantum efficiency of 23.2%, representing one of the best performance pure-red PeLEDs based on mixed-halide CsPb(Br/I)3 QDs reported to date.

High-Performance All-Inorganic Architecture Perovskite Light-Emitting Diodes Based on Tens-of-Nanometers-Sized CsPbBr3 Emitters in a Carrier-Confined Heterostructure.

Developing green perovskite light-emitting diodes (PeLEDs) with a high external quantum efficiency (EQE) and low efficiency roll-off at high brightness remains a critical challenge. Nanostructured emitter-based devices have shown high efficiency but restricted ascending luminance at high current densities, while devices based on large-sized crystals exhibit low efficiency roll-off but face great challenges to high efficiency. Herein, we develop an all-inorganic device architecture combined with utilizing tens-of-nanometers-sized CsPbBr3 (TNS-CsPbBr3) emitters in a carrier-confined heterostructure to realize green PeLEDs that exhibit high EQEs and low efficiency roll-off. A typical type-I heterojunction containing TNS-CsPbBr3 crystals and wide-bandgap Cs4PbBr6 within a grain is formed by carefully controlling the precursor ratio. These heterostructured TNS-CsPbBr3 emitters simultaneously enhance carrier confinement and retain low Auger recombination under a large injected carrier density. Benefiting from a simple device architecture consisting of an emissive layer and an oxide electron-transporting layer, the PeLEDs exhibit a sub-bandgap turn-on voltage of 2.0 V and steeply rising luminance. In consequence, we achieved green PeLEDs demonstrating a peak EQE of 17.0% at the brightness of 36,000 cd m-2, and the EQE remained at 15.7% and 12.6% at the brightness of 100,000 and 200,000 cd m-2, respectively. In addition, our results underscore the role of interface degradation during device operation as a factor in device failure.

Charge Injection and Auger Recombination Modulation for Efficient and Stable Quasi-2D Perovskite Light-Emitting Diodes.

The inefficient charge transport and large exciton binding energy of quasi-2D perovskites pose challenges to the emission efficiency and roll-off issues for perovskite light-emitting diodes (PeLEDs) despite excellent stability compared to 3D counterparts. Herein, alkyldiammonium cations with different molecular sizes, namely 1,4-butanediamine (BDA), 1,6-hexanediamine (HDA) and 1,8-octanediamine (ODA), are employed into quasi-2D perovskites, to simultaneously modulate the injection efficiency and recombination dynamics. The size increase of the bulky cation leads to increased excitonic recombination and also larger Auger recombination rate. Besides, the larger size assists the formation of randomly distributed 2D perovskite nanoplates, which results in less efficient injection and deteriorates the electroluminescent performance. Moderate exciton binding energy, suppressed 2D phases and balanced carrier injection of HDA-based PeLEDs contribute to a peak external quantum efficiency of 21.9%, among the highest in quasi-2D perovskite based near-infrared devices. Besides, the HDA-PeLED shows an ultralong operational half-lifetime T50 up to 479h at 20mA cm‒2, and sustains the initial performance after a record-level 30000 cycles of ON-OFF switching, attributed to the suppressed migration of iodide anions into adjacent layers and the electrochemical reaction in HDA-PeLEDs. This work provides a potential direction of cation design for efficient and stable quasi-2D-PeLEDs.