Patellofemoral Joint Kinematics Research Articles

Open wedge high tibial osteotomy alters patellofemoral joint kinematics: A multibody simulation study.

Changes in lower limb alignment after open-wedge high tibial osteotomy (owHTO) influence joint kinematics. The aim of this study was to investigate the morphological and kinematic changes of the knee joint, in particular the patellofemoral joint, using a multibody simulation model. OwHTO with an open tibial wedge of 6-12 mm (1 mm intervals) was virtually performed on each of 13 three-dimensional (3D) computer-aideddesign models (CAD models) derived from computer tomography scans of full-leg cadaver specimens. For each owHTO, an individual biomechanical simulation model was built and knee flexion from 5° to 100° was simulated using a multibody simulation model of the native knee. Morphologic and alignment parameters as well as tibiofemoral and patellofemoral kinematic parameters were evaluated. Almost linear changes in tibial tuberosity trochlea groove(TT-TG) (0.42 mm/1 mm wedge height) were observed which led to pathological values (TT-TG > 20 mm) in 3 out of 13 knees. Furthermore, a 6 mm increase in osteotomy wedge height increased lateral patellofemoral rotation by 0.8° (range: 0.39° to 1.11°) and led to a lateral patellar translation of 0.8 mm (range: 0.37-3.11 mm) on average. Additionally, valgisation led to a medial translation of the tibia and a decrease in the degree of tibial internal rotation during knee flexion of approximately 0.3°/1 mm increase in osteotomy wedge height. The increase in TT-TG and the biomechanical effects observed influence patellofemoral tracking, which may increase retropatellar pressure and are potential risk factors for the development of anterior knee pain.

Validation and evaluation of subject-specific finite element models of the pediatric knee

Finite element (FE) models have been widely used to investigate knee joint biomechanics. Most of these models have been developed to study adult knees, neglecting pediatric populations. In this study, an atlas-based approach was employed to develop subject-specific FE models of the knee for eight typically developing pediatric individuals. Initially, validation simulations were performed at four passive tibiofemoral joint (TFJ) flexion angles, and the resulting TFJ and patellofemoral joint (PFJ) kinematics were compared to corresponding patient-matched measurements derived from magnetic resonance imaging (MRI). A neuromusculoskeletal-(NMSK)-FE pipeline was then used to simulate knee biomechanics during stance phase of walking gait for each participant to evaluate model simulation of a common motor task. Validation simulations demonstrated minimal error and strong correlations between FE-predicted and MRI-measured TFJ and PFJ kinematics (ensemble average of root mean square errors < 5 mm for translations and < 4.1° for rotations). The FE-predicted kinematics were strongly correlated with published reports (ensemble average of Pearson's correlation coefficients (ρ) > 0.9 for translations and ρ > 0.8 for rotations), except for TFJ mediolateral translation and abduction/adduction rotation. For walking gait, NMSK-FE model-predicted knee kinematics, contact areas, and contact pressures were consistent with experimental reports from literature. The strong agreement between model predictions and experimental reports underscores the capability of sequentially linked NMSK-FE models to accurately predict pediatric knee kinematics, as well as complex contact pressure distributions across the TFJ articulations. These models hold promise as effective tools for parametric analyses, population-based clinical studies, and enhancing our understanding of various pediatric knee injury mechanisms. They also support intervention design and prediction of surgical outcomes in pediatric populations.

Internal Rotation, Varus, and Anterior Femoral Component Malalignments Adversely Affect Patellofemoral Joint Kinematics in Patellofemoral Arthroplasty.

Patellofemoral arthroplasty (PFA) is reported to provide nearly normal PF joint kinematics but only with adequate surgical techniques. This study evaluated the effects of various femoral component settings on patellar component biomechanics. A dynamic musculoskeletal computer simulation analyzed normal knee and standard PFA models, as well as 8 femoral component malposition models: 5° internal or external rotation, 5° valgus or varus, 5° extension or flexion, and 3-mm or 5-mm anterior positioning. Mediolateral patellar translation, lateral patellar tilt, and contact force and stress at the PF joint were measured in each model during gait. The patella in the standard PFA model was shifted up to 5.0 mm laterally near heel off and was tilted up to 3.0° laterally at heel strike compared to the normal knee model. The patella in the external rotation model translated more laterally in the direction of the femoral component setting than in the standard model. However, in the internal rotation and varus alignment models, the patellar lateral shift occurred largely in the opposite direction of the femoral component setting. The patella in most models was tilted in the same direction as the femoral component setting. The PF contact force was increased, especially in the anterior femoral position models, by up to 30 MPa compared with 20 MPa in the standard model. Internal rotation, varus, and anterior femoral component settings during PFA should be avoided to reduce postoperative complications, whereas external rotation might be appropriate only for cases with lateral patellar instability.

Computer-based analysis of different component positions and insert thicknesses on tibio-femoral and patello-femoral joint dynamics after cruciate-retaining total knee replacement

BackgroundPositioning of the implant components and tibial insert thickness constitute critical aspects of total knee replacement (TKR) that influence the postoperative knee joint dynamics. This study aimed to investigate the impact of implant component positioning (anterior-posterior and medio-lateral shift) and varying tibial insert thickness on the tibio-femoral (TF) and patello-femoral (PF) joint kinematics and contact forces after cruciate-retaining (CR)-TKR. MethodA validated musculoskeletal multibody simulation (MMBS) model with a fixed-bearing CR-TKR during a squat motion up to 90° knee flexion was deployed to calculate PF and TF joint dynamics for varied implant component positions and tibial insert thicknesses. Evaluation was performed consecutively by comparing the respective knee joint parameters (e.g. contact force, quadriceps muscle force, joint kinematics) to a reference implant position. ResultsThe PF contact forces were mostly affected by the anterior-posterior as well as medio-lateral positioning of the femoral component (by 3 mm anterior up to 31 % and by 6 mm lateral up to 14 %). TF contact forces were considerably altered by tibial insert thickness (24 % in case of + 4 mm increase) and by the anterior-posterior position of the femoral component (by 3 mm posterior up to 16 %). Concerning PF kinematics, a medialised femoral component by 6 mm increased the lateral patellar tilt by more than 5°. ConclusionsOur results indicate that regarding PF kinematics and contact forces the positioning of the femoral component was more critical than the tibial component. The positioning of the femoral component in anterior-posterior direction on and PF contact force was evident. Orthopaedic surgeons should strictly monitor the anterior-posterior as well as the medio-lateral position of the femoral component and the insert thickness.

A combined anterior cruciate ligament/Meniscal injury alters the patellofemoral joint kinematics of anterior cruciate ligament-deficient knees during a single-leg lunge exercise: A cross-sectional study.

Anterior cruciate ligament deficiency (ACLD) is often accompanied by concomitant meniscal tears. The study aimed to assess the kinematic alterations of patellofemoral joint (PFJ) in anterior cruciate ligament deficiency knees with or without meniscal tears during a single-leg lunge. Sixty unilateral anterior cruciate ligament deficiency patients were recruited for the study, including 15 isolated anterior cruciate ligament deficiency patients (group 1), 15 anterior cruciate ligament deficiency patients with medial meniscal tears (group 2), 15 patients with lateral meniscal tears (group 3) and 15 patients with combined medial/lateral meniscal tears (group 4). The patellofemoral joint kinematics were determined by a single fluoroscopic image system. Patellofemoral joint kinematics of contralateral anterior cruciate ligament-intact (ACLI) and anterior cruciate ligament deficiency knees were compared. With or without meniscal tears, anterior cruciate ligament deficiency knees had significantly smaller patellar flexion than the anterior cruciate ligament-intact knees (∼5°-10°; p < 0.05). anterior cruciate ligament deficiency knees had more patellar lateral tilting by approximately 1°-2° than the anterior cruciate ligament-intact knees (p < 0.05) in groups 2, 3, and 4. anterior cruciate ligament deficiency groups with medial meniscal deficiencies showed consistent increased lateral patellar translations (2-4mm) compared to the anterior cruciate ligament-intact group during a single-leg lunge. The results indicate that meniscal tears alter anterior cruciate ligament deficiency patients' patellofemoral joint kinematics and the types of the meniscal injuries also affect the patellofemoral joint kinematics. Considering the varying effects of meniscal tears on the patellofemoral joint kinematics, specific treatments for anterior cruciate ligament deficiency patients with meniscal tears should be proposed in some closed kinetic chain (CKC) exercise programs, such as single-leg lunge.

Simultaneous Measurement of Patellofemoral Joint Kinematics and Contact Mechanics in Intact Knees: A Cadaveric Study.

ObjectivePatellofemoral kinematics and contact mechanics are important measurements for the assessment of patellofemoral joint (PFJ) problems. Simultaneously measuring PFJ contact pressures and kinematics is a challenging task. The purpose of this study was to simultaneously measure the kinematics and mean/peak contact pressures in the PFJs of cadaveric knees.MethodsThis was a comparative study performed on fresh cadaveric knees. The kinematic data was acquired for nine cadaveric knees using an optical tracking system. Data about the contact pressure and contact area in the PFJ was obtained at knee flexion angles of 0°, 30°, 60°, 90°, and 120° using a pressure sensor. Intraclass correlation coefficients (ICCs) and minimal detectable differences (MDDs) of six degrees of freedom (6 DOF) in the PFJs were calculated. ICCs and the MDDs of contact pressure, peak pressure, and contact area in the PFJs were also analyzed. We also compared the kinematics of the cadaveric knees before and after the insertion of the pressure sensor.ResultsAll ICC values of 6 DOF in the PFJs were found to be greater than or equal to 0.924. Regarding medial–lateral rotation, the patellar showed a simplified movement pattern that demonstrated progressive lateral rotation of 4.8° ± 3.4° at 120° of knee flexion. While for patellar tilting, the patella showed medial tilting that peaked at 7.2 ± 2.5° at 30° of knee flexion. Whereas no significant differences in PFJ kinematics were found between with and without the placement of the pressure sensor at all knee flexions (P > 0.05). Most of the ICC values for contact pressure, peak contact pressure, and contact area ranged from 0.8 to 0.9. The MDDs for rotational displacement were 0.9° and 0.6 mm for translational displacement. No statistical differences in patellar kinematics were found before and after the insertion of the pressure sensor.ConclusionsThe setup in the present study enables researchers to simultaneously and synchronously collect real‐time PFJ kinematics and tibiofemoral joint (TFJ) biomechanical kinematic data with high reliability. The low MDDs enabled the researchers to obtain an accurate interpretation of the kinematic and contact mechanics measurement using the experimental setting used in the present study.

In Vivo Knee Kinematics in Patients With Arthrofibrosis After Anterior Cruciate Ligament Reconstruction

Context: Arthrofibrosis after anterior cruciate ligament (ACL) reconstruction can be detrimental to the knee joint function and patient outcomes. However, the effects of arthrofibrosis on the in vivo tibiofemoral and patellofemoral joint kinematics after ACL reconstruction remain unclear. Objective: The objective of this study was to quantify the in vivo knee kinematics during a dynamic lunge task in the knee with arthrofibrosis after ACL reconstruction. Methods: Eleven patients with arthrofibrosis in one knee after ACL reconstruction participated in this study. Computed tomography and dual fluoroscopic imaging were used to evaluate in vivo kinematics of affected and contralateral knees during a lunge task. Differences in 6 degrees of freedom tibiofemoral kinematics and patellar tracking between limbs were assessed via repeated-measures analysis of variance. Results: Internal tibial rotation (5.2° vs 7.5°, respectively; P &lt; .001) and inferior patellar shift (24.6 mm vs 28.9 mm, respectively; P &lt; .001) were significantly lower in the arthrofibrotic knee compared with the contralateral knee from 15° to 75° of knee flexion. The patella in the arthrofibrotic knee significantly less flexed by 9.1° (P = .009) throughout the measured ROM and less laterally tilted by 3° (P = .017) compared with the contralateral knee from 30° to 75° of knee flexion. Conclusions: A significant superior shift and medial tilt of the patella were found in the affected knee compared with those in the contralateral knee during the dynamic lunge. Decreased internal tibial rotation and patellar flexion were found in knees with arthrofibrosis following ACL reconstruction; whether these kinematic changes are caused by arthrofibrosis need further investigation.

Effects of Weight-Bearing on Tibiofemoral, Patellofemoral, and Patellar Tendon Kinematics in Older Adults.

Quantification of natural knee kinematics is essential for the assessment of joint function in the diagnosis of pathologies. Combined measurements of tibiofemoral and patellofemoral joint kinematics are necessary because knee pathologies, such as progression of osteoarthritis and patellar instability, are a frequent concern in both articulations. Combined measurement of tibiofemoral and patellofemoral kinematics also enables calculation of important quantities, specifically patellar tendon angle, which partly determines the loading vector at the tibiofemoral joint and patellar tendon moment arm. The goals of this research were to measure the differences in tibiofemoral and patellofemoral kinematics, patellar tendon angle (PTA), and patellar tendon moment arm (PTMA) that occur during non-weight-bearing and weight-bearing activities in older adults. Methods: High-speed stereo radiography was used to measure the kinematics of the tibiofemoral and patellofemoral joints in subjects as they performed seated, non-weight-bearing knee extension and two weight-bearing activities: lunge and chair rise. PTA and PTMA were extracted from the subject’s patellofemoral and tibiofemoral kinematics. Kinematics and the root mean square difference (RMSD) between non-weight-bearing and weight-bearing activities were compared across subjects and activities. Results: Internal rotation increased with weight-bearing (mean RMSD from knee extension was 4.2 ± 2.4° for lunge and 3.6 ± 1.8° for chair rise), and anterior translation was also greater (mean RMSD from knee extension was 2.2 ± 1.2 mm for lunge and 2.3 ± 1.4 mm for chair rise). Patellar tilt and medial–lateral translation changed from non-weight-bearing to weight-bearing. Changes of the patellar tendon from non-weight-bearing to weight-bearing were significant only for PTMA. Conclusions: While weight-bearing elicited changes in knee kinematics, in most degrees of freedoms, these differences were exceeded by intersubject differences. These results provide comparative kinematics for the evaluation of knee pathology and treatment in older adults.

Gender differences in knee kinematics during weight-bearing knee flexion for patients with arthrofibrosis after anterior cruciate ligament reconstruction

BackgroundKnowledge of tibiofemoral and patellofemoral joint kinematics is important for understanding gender-related dimorphism in developing knee arthrofibrosis and advancement of related treatments. The objective of our study was to investigate gender differences existing in tibiofemoral kinematics and patellar tracking in patients with arthrofibrosis after anterior cruciate ligament (ACL) reconstruction during weight-bearing knee flexion.MethodsThe tibiofemoral and patellofemoral joint kinematics were measured in 30 patients (15 male and 15 female) with arthrofibrosis after ACL reconstruction during a lunge task, using computed tomography and dual fluoroscopic imaging system. These data were analyzed for gender differences.ResultsThe range of tibial rotation, patellar inferior shift, tilt, and flexion were significantly decreased in the affected knee compared to the contralateral knee from 15° to 75° of knee flexion (P ≤ 0.04). Statistically significant difference was detected for medial tibial translation between male and female patients at 60° (P = 0.04) and 75° of knee flexion (P = 0.02). The tibial rotation was significantly decreased at 60° (P = 0.03) and 75° of knee flexion (P < 0.01) in females. The inferior patellar shift in females was significantly lower than that in males at 15° (P = 0.04) and 30° of knee flexion (P = 0.01). The patellar tilt was significantly lower at 60° (P = 0.02) and 75° of knee flexion (P < 0.01) in females compared to males.ConclusionsThe results indicated a significant effect of gender on knee kinematics in patients with arthrofibrosis after ACL reconstruction during weight-bearing knee flexion. These gender differences in tibiofemoral kinematics and patellar tracking may warrant further investigations to determine implications for making gender-specific surgical treatments and rehabilitation programs.

Posterior Tibial Loading Results in Significant Increase of Peak Contact Pressure in the Patellofemoral Joint During Anterior Cruciate Ligament Reconstruction: A Cadaveric Study

Background: Inappropriate posterior tibial loading and initial graft tension during anterior cruciate ligament (ACL) reconstruction may cause altered patellofemoral joint (PFJ) contact mechanics, potentially resulting in pain and joint degeneration. Hypothesis: PFJ contact pressure would increase with the increases in posterior tibial loading and graft tension during ACL reconstruction. Study Design: Controlled laboratory study. Methods: Nine fresh-frozen, nonpaired human cadaveric knees were tested in a customized jig from 0° to 120° of knee flexion. First, the knee was tested in the ACL-intact state. Second, reconstruction of the ACLs using different posterior tibial loadings and graft tensions were performed. The posterior tibial loading was evaluated at 2 levels: 33.5 and 67 N. Graft tension was assessed at 3 levels: low tension (20 N), medium tension (60 N), and high tension (80 N). Maximum values of peak contact pressure in the medial and lateral patellar facets were compared between ACL-intact and ACL-reconstructed knees. The PFJ kinematics between ACL-intact knees and ACL-reconstructed knees were compared during knee flexion at 30°, 60°, 90°, and 120°. Results: Reconstruction of ACLs with both low and high posterior tibial loading resulted in significant increases of peak contact pressure in the medial (range of differences, 0.46-0.92 MPa; P < .05) and lateral (range of differences, 0.51-0.83 MPa; P < .05) PFJ compared with the ACL-intact condition. However, no significant differences in PFJ kinematics were identified between ACL-reconstructed knees and ACL-intact knees. In ACL-reconstructed knees, it was found that a high posterior tibial loading resulted in high peak contact pressure on the medial patellar side (range of differences, 0.37-0.46 MPa; P < .05). No significant difference in peak contact pressure was observed among the differing graft tensions. Conclusion: In this cadaveric model, ACL reconstruction resulted in significant increases of peak contact pressure in the PFJ facet when compared with the ACL-intact condition. A high posterior tibial loading can lead to high medial PFJ peak contact pressure. Graft tension was found to not significantly affect PFJ contact pressure during ACL reconstruction. Clinical Relevance: An excessive posterior tibial loading during ACL reconstruction resulted in increased PFJ contact pressures at time of surgery. These data suggest that a low posterior tibial loading might be preferred during ACL reconstruction surgery to reduce the PFJ contact pressure close to that of the ACL-intact condition.

Regressional analysis of the patella parameters of male cadaveric knees found among South East Nigerians: A useful guide to patella replacement during total knee replacement

Background: Total knee replacement (TKR) is a viable option for the management of osteoarthritis, and it has proven to be both effective and successful. Optimization of the patellofemoral joint kinematics is important for surgeons who choose to resurface the patella during TKR. The whole idea is to get the final patellar bone-prosthesis composite thickness to match the original patellar thickness before the surgery. Aim: To correlate patella height (PH) and patella width (PW) with patella thickness (PT) as well as build a regression model through which the dimensions can predict the thickness among the native knees of the South East Nigerians. Materials and Methods: This is a correlational, nonexperimental, and observational study conducted on 60 knees from 30 male cadavers taken from the anatomy laboratory of the University of Nigeria, Enugu Campus. The PH, PW, and PT were measured by using specific endpoints and the observed data were subjected to statistical correlation analysis. Results: PH and PT were strongly positively correlated, r(59) = 0.797, P < 0.001. Results of the multiple linear regression indicated that there was a collective significant effect between the PH, PW, and PT (F(2, 57) = 51.486, P < 0.001, R2 = 0.644). The individual predictors were examined further and indicated that PH (t = 4.931, P < 0.001) was a significant predictor whereas PW (t = 1.153, P = 0.254) was not a significant predictor in the model. The patella’s predicted thickness is equal to 1.734+0.328 (PH in cm) +0. PT increased 0.328 cm for each centimeter of height. The PH was the only significant predictor of PT. Conclusion: This study was able to establish a correlation between the PH, PW, and PT, and it was able to demonstrate PH and PW as predictors of PT among the population of South East Nigeria.

Short-term effectiveness of an intervention targeting lower limb range of motion on pain and disability in patellofemoral pain patients: A randomized, non-concurrent multiple-baseline study

IntroductionPatellofemoral pain (PFP) is a common and often long-standing musculoskeletal condition. Evidence of the effectiveness of interventions addressing soft tissue flexibility is conflicting and of inconsistent scientific quality. However, reduced soft tissue flexibility can negatively affect patellofemoral joint kinematics. Lower limb range of motion (LLROM) reflects soft tissue flexibility throughout the kinetic chain. The aim was to evaluate the short-term effectiveness of an intervention targeting LLROM on pain and disability in patients with PFP. MethodsA randomized, non-concurrent, multiple-baseline single-case design with a two-week intervention phase and baseline and postintervention phase with varying length was conducted. Eight participants (5 females, 3 males) of age 19(±1.6) years, weekly sports participation 12(±3.1) hours and 17(±14) months symptom duration were included. The Anterior Knee Pain Scale – Dutch Version (AKPS-DV) and the Patient Specific Complaint Scale (PSCS) were administered twice a week. After allocating participants to one of four subgroups of reduced LLROM the intervention was applied. The intervention consisted of soft tissue techniques (mobilization, taping, and stretching). ResultsParticipant 3 and 6 showed a medium and small but statistically significant positive effect on the AKPS-DV. Participant 2 showed a large and statistically significant positive effect on the PSCS. ConclusionsThis study provides moderate evidence that an intervention targeting LLROM in patients with PFP reduces pain and disability in the short-term. Further research is needed to evaluate the long-term effectiveness and optimize individual treatment outcomes.

Optimization location of femoral attachment in medial patellofemoral ligament reconstruction assisted with arthroscopy for patellar dislocation

To investigate the technique of optimizing the location of femoral attachment in medial patellofemoral ligament (MPFL) reconstruction assisted with arthroscopy and evaluate the effectiveness. Between January 2014 and September 2018, 35 patients with patellar dislocation were admitted. There were 14 males and 21 females with an average age of 22.6 years (range, 16-38 years). All patients had a history of knee sprain. The disease duration ranged from 1 to 7 days (mean, 2.8 days). Patellar dislocation occurred 2-4 times (mean, 2.5 times). The preoperative Lysholm score and Kujala score were 47.60±11.24 and 48.37±9.79, respectively. The patellar congruence angle was (31.40±6.81)°, the patellar tilt angle was (29.95±5.44)°, the lateral patellofemoral angle was (-11.46±5.18)°, and the tibial tubercle-trochlear groove distance was (16.66±1.28) mm. All patients were treated by MPFL reconstruction with the semitendinosus tendon under arthroscopy. During operation, the suture anchors were inserted into the midpoint and the 1/3 point of superomedial edge of the patella. Then, the femoral tunnels were created in medial femoral condyle through limited excision. For tendon fixation, the Kirschner wires were inserted into adductor tubercle, medial epicondyle of femur, and the midpoint between the two points, as well as the anteriorly and posteriorly. Afterwards, the changes of ligament length and tension, patellar tracking, and the relationship of patella and femoral trochlea were evaluated, thereby determining the optimized femoral attachment for MPFL reconstruction. Finally, the patellar congruence angle, patellar tilt angle, and lateral patellofemoral angle were measured by imaging to assess the relationship of patella and femoral trochlea. Moreover, Lysholm score and Kujala score were used to evaluate the knee joint function. All incisions healed by first intention without infection. All patients were followed up 12-18 months (mean, 15.4 months). At 12 months, the Lysholm score was 94.40±3.99 and the Kujala score was 92.28±4.13, which were significant higher than those before operation ( P<0.05). No patellar dislocation occurred during follow-up. At 12 months, the patellar congruence angle was (6.57±4.59)°, the patellar tilt angle was (9.73±2.82)°, the lateral patellofemoral angle was (7.14±4.63)°, which were superior to those before operation ( P<0.05). During the MPFL reconstruction under arthroscopy, a higher positioning accuracy for the femoral attachment and satisfactory effectiveness can be obtained by evaluating MPFL length and tension, patellofemoral joint kinematics, and patellar tracking.

The effect of patellofemoral pain syndrome on patellofemoral joint kinematics under upright weight-bearing conditions.

Patellofemoral pain (PFP) is commonly caused by abnormal pressure on the knee due to excessive load while standing, squatting, or going up or down stairs. To better understand the pathophysiology of PFP, we conducted a noninvasive patellar tracking study using a C-arm computed tomography (CT) scanner to assess the non-weight-bearing condition at 0° knee flexion (NWB0°) in supine, weight-bearing at 0° (WB0°) when upright, and at 30° (WB30°) in a squat. Three-dimensional (3D) CT images were obtained from patients with PFP (12 women, 6 men; mean age, 31 ± 9 years; mean weight, 68 ± 9 kg) and control subjects (8 women, 10 men; mean age, 39 ± 15 years; mean weight, 71 ± 13 kg). Six 3D-landmarks on the patella and femur were used to establish a joint coordinate system (JCS) and kinematic degrees of freedom (DoF) values on the JCS were obtained: patellar tilt (PT, °), patellar flexion (PF, °), patellar rotation (PR, °), patellar lateral-medial shift (PTx, mm), patellar proximal-distal shift (PTy, mm), and patellar anterior-posterior shift (PTz, mm). Tests for statistical significance (p < 0.05) showed that the PF during WB30°, the PTy during NWB0°, and the PTz during NWB0°, WB0°, and WB30° showed clear differences between the patients with PFP and healthy controls. In particular, the PF during WB30° (17.62°, extension) and the PTz during WB0° (72.5‬0 mm, posterior) had the largest rotational and translational differences (JCS Δ = patients with PFP—controls), respectively. The JCS coordinates with statistically significant difference can serve as key biomarkers of patellar motion when evaluating a patient suspected of having PFP. The proposed method could reveal diagnostic biomarkers for accurately identifying PFP patients and be an effective addition to clinical diagnosis before surgery and to help plan rehabilitation strategies.

Prediction of patellofemoral joint kinematics and contact through co-simulation of rigid body dynamics and nonlinear finite element analysis

Joint-level rigid body dynamics simulations, when coupled with tissue-level finite element analyses, can simultaneously provide movement and tissue deformation metrics to understand mechanical interactions within the joint on a multi-scale level. In this study, a co-simulation workflow of a joint-level rigid body model that predicts the relative motion as a function of the non-linear cartilage response predicted by a non-linear implicit finite element solver is presented. Predictions are compared to in-vitro measurements (The Open Knee(s) project) in terms of the mean error and level-of-agreement: pressureerror = 0.46 MPa (level-of-agreement, −0.23 – 1.1 MPa); areaerror = −89 mm2 (level-of-agreement, −280 – 98 mm2) and contact forceerror = 93 N (level-of-agreement, 7.8 – 180 N). The automated co-simulation control algorithm enables multiscale coupling between joint and tissue-level models with real-time two-way communication as opposed to the traditional feed-forward approach of multi-scale models.

Can Computer-Assisted Total Knee Arthroplasty Support the Prediction of Postoperative Three-Dimensional Kinematics of the Tibiofemoral and Patellofemoral Joints at the Replaced Knee?

The aim of this study was to analyze the extent to which postoperative patellofemoral joint (PFJ) kinematics assessed at 6-month follow-up after total knee arthroplasty (TKA) mimics the intraoperative kinematics after final component implantation. The study hypothesis, already proved in terms of tibiofemoral joint (TFJ) kinematics, is that the intraoperative assessment of PFJ kinematics after component implantation is also capable of predicting postoperative knee kinematics during activities of daily living. Twenty patients selected for TKA with patellar resurfacing were implanted using surgical navigation, including patellar component positioning via a novel computer-assisted procedure. This allowed for intraoperative TFJ and PFJ kinematic assessment after final component implantation. At 6-month follow-up, all patients were contacted for follow-up control; in addition to clinical examination, this implied postoperative kinematics assessments by three-dimensional video fluoroscopy of the replaced knee during standard activities of daily living. Several traditional PFJ, as well as TFJ, rotations and translations were calculated intra- and postoperatively and then statistically compared. Good postoperative replication of the intraoperative measurements was observed for most of PFJ variables analyzed, as well as those for TFJ. Relevant statistical analysis also supported the significant consistency between the intra- and postoperative measurements. Pertaining to the present findings on a statistical basis, intraoperative measurements performed at both TFJ and PFJ kinematics using a surgical navigation system under passive conditions, are predictive of the overall knee kinematics experienced at postoperative follow-ups by the same replaced knees in typical activities of daily living.

Evaluation of predicted patellofemoral joint kinematics with a moving-axis joint model

The main objectives of this study were to expand the moving-axis joint model concept to the patellofemoral joint and evaluate the patellar motion against experimental patellofemoral kinematics. The experimental data was obtained through 2D-to-3D bone reconstruction of EOS images and segmented MRI data utilizing an iterative closest point optimization technique. Six knee model variations were developed using the AnyBody Modeling System and subject-specific bone geometries. These models consisted of various combinations of tibiofemoral (hinge, moving-axis, and interpolated) and patellofemoral (hinge and moving-axis) joint types. The newly introduced interpolated tibiofemoral joint is calibrated from the five EOS quasi-static lunge positions. The patellofemoral axis of the hinge model was defined by performing surface fits to the patellofemoral contact area; and the moving-axis model was defined based upon the position of the patellofemoral joint at 0° and 90° tibiofemoral-flexion. In between these angles, the patellofemoral axis moved linearly as a function of tibiofemoral-flexion, while outside these angles, the axis remained fixed. When using a moving-axis tibiofemoral joint, a hinge patellofemoral joint offers (−5.12 ± 1.23 mm, 5.81 ± 0.97 mm, 14.98 ± 2.30°, −4.35 ± 1.95°) mean differences (compared to EOS) while a moving-axis patellofemoral model provides (−2.69 ± 1.04 mm, 1.13 ± 0.80 mm, 12.63 ± 2.03°, 1.74 ± 1.46°) in terms of lateral-shift, superior translation, patellofemoral-flexion, and patellar-rotation, respectively. Furthermore, the model predictive capabilities increased as a direct result of adding more calibrated positions to the tibiofemoral model (hinge-1, moving-axis-2, and interpolated-5). Overall, a novel subject-specific moving-axis patellofemoral model has been established; that produces realistic patellar motion and is computationally fast enough for clinical applications.

Repair of the medial patellofemoral ligament with suture tape augmentation leads to similar primary contact pressures and joint kinematics like reconstruction with a tendon graft: a biomechanical comparison.

To compare suture tape-augmented MPFL repair with allograft MPFL reconstruction using patellofemoral contact pressure and joint kinematics to assess the risk of patellofemoral over-constrainment at point zero. A total of ten fresh frozen cadaveric knee specimens were tested in four different conditions of the MPFL: (1) native, (2) cut, (3) reconstructed with tendon graft, and (4) augmented with suture tape. The patellofemoral mean pressure (MP), peak pressure (PP) and contact area (CA) were measured independently for the medial and lateral compartments using pressure-sensitive films. Patellar tilt (PT) and shift (PS) were measured using an optical 3D motion tracking system. Measurements were recorded at 0°, 10°, 20°, 30°, 60° and 90° of flexion. Both the tendon graft and the internal brace were preloaded with 2N, 5N, and 10N. There was no significant differences found between surgical methods for medial MP, medial PP, medial CA, lateral MP and PS at any preload or flexion angle. Significant differences were seen for lateral PP at 20° knee flexion and 10N preload (suture tape vs. reconstruction: 1045.9 ± 168.7kPa vs. 1003.0 ± 151.9kPa; p = 0.016), for lateral CA at 10° knee flexion and 10N preload (101.4 ± 39.5 mm2 vs. 108.7 ± 36.6 mm2; p = 0.040), for PT at 10° knee flexion and 2N preload (-1.9 ± 2.5° vs. -2.5 ± 2.3°; p = 0.033) and for PT at 0° knee flexion and 10N preload (-0.8 ± 2.5° vs. -1.8 ± 3.1°; p = 0.040). A preload of 2N on the suture tape was the closest in restoring the native joint kinematics. Suture tape augmentation of the MPFL resulted in similar primary contact pressures and joint kinematics in comparison with MPFL reconstruction using a tendon graft. A pretension of 2N was found to restore the knee joint closest to normal patellofemoral kinematics.

Sagittal patellar flexion angle: a novel clinically validated patellar height measurement reflecting patellofemoral kinematics useful throughout knee flexion.

Patellar height measurements on lateral radiographs are dependent on knee flexion which makes standardisation of measurements difficult. This study described a plain radiographic measurement of patellar sagittal height which reflects patellofemoral joint kinematics and can be used at all degrees of flexion. The study had two parts. Part one involved 44 normal subjects to define equations for expected patellar position based on the knee flexion angles for three new patellar height measurements. A mixed model regression with random effect for individual was used to define linear and polynomial equations for expected patellar position relating to three novel measurements of patella height: (1) patellar progression angle (trochlea), (2) patellar progression angle (condyle) and (3) sagittal patellar flexion. Part two was retrospective and involved applying these measurements to a surgical cohort to identify differences between expected and measured patellar position pre- and post-operatively. All three measurements provided insight into patellofemoral kinematics. Sagittal patellar flexion was the most useful with the least residual error, was the most reliable, and demonstrated the greatest detection clinically. Clinically applied radiographic measurements have been described for patellar height which reflect the sagittal motion of the patella and can be used regardless of the degree of flexion in which the radiograph was taken. The expected sagittal patellar flexion linear equation should be used to calculate expected patellar height. IV.

Resurfacing in a Posterior-Stabilized Total Knee Arthroplasty Reduces Patellar Crepitus Complication: A Randomized, Controlled Trial

BackgroundPatellar crepitus (PC) is a common complication after total knee arthroplasty (TKA) using a posterior-stabilized (PS) prosthesis. While numerous factors have been associated with PC development after PS-TKA, patellar resurfacing (PR) which directly impacts the patellofemoral joint kinematics has been underinvestigated. A prospective, randomized, controlled trial was conducted to (1) compare the PC incidence in PR and non-PR PS-TKA, (2) determine the time of PC presentation in PS-TKA, (3) identify radiographic parameters associated with PC, and (4) compare clinical outcomes of patients with and without PR. MethodsA total of 84 patients who underwent unilateral TKA using the Legion PS Total Knee System were randomized into PR group or non-PR group. PC incidence, time of PC presentation, radiographic parameters associated with PC development, and clinical outcomes were evaluated at 3 months, 6 months, 9 months, and 1 year postoperatively. ResultsPC occurred significantly more in the non-PR group (23.1% vs 7.3%, P = .048). Time of PC presentation in both groups was not different. Anterior knee pain was found in 16.7% of crepitus patients, and none required any surgical procedure. The non-PR knees had significant decreases in patellar shift index, patellar displacement, Insall-Salvati ratio, and patellar component height and increase in change in posterior femoral offset. Oxford and patellar scores were significantly better in the PR group at 9 months and 1 year. ConclusionGiven higher PC incidence and several worse clinical outcomes in the non-PR, we recommend resurfacing during PS-TKA with this knee system to avoid PC development.