Particle Size Analysis Research Articles

Purification of graphite from spent carbon cathodes through the reduction of the mechanical entrainment of cryolite using polyaluminium chloride as a flocculant

Spent carbon cathodes (SCCs) generated during electrolytic aluminum production pose significant environmental hazards. To optimize resource utilization, flotation is used as an early process for the clean recovery of valuable graphite from waste cathodes. However, the mechanical entrainment in flotation restricts the further improvement of product purity, resulting in an increase in waste gas and wastewater discharge in the subsequent purification process. In this study, to increase the fixed carbon content of flotation products, flocculant was first applied to the flotation separation of SCCs, and polyaluminum chloride (PAC) was used to flocculate cryolite with high impurity content to reduce mechanical entrainment in the flotation process. Zeta potential measurements, particle size analysis, optical microscopy, and scanning electron microscopy confirmed the agglomeration of cryolite under the action of PAC. Additionally, the DLVO (Derjaguin, Landau, Verwey, and Overbeek) theory was used to estimate the interaction energy to further explain the mechanism underlying cryolite agglomeration. Interaction energy calculation revealed that the attraction energy between particles was dominant at the PAC concentration of 2000 mg/L. Flotation experiments indicated that under a constant pulp pH of 7.8, the absence of sodium silicate, and a stirring speed of 1200rpm, mechanical entrainment decreased from 91.53 ± 1.53g/L to 69.80 ± 1.90g/L, and the carbon grade of the product increased from 83.07 ± 0.28% to 88.94 ± 0.30%. Overall, the proposed purification method provides a new approach for the efficient recovery of graphite in waste cathodes, which is of great significance for the sustainable development of graphite resources.

Clays to lightweight aggregates: Thermochemical modeling and industrial validation

The creation of thermochemical models to forecast the dependent variables governing the bloatability of lightweight aggregates (LWAs) is the goal of this work. Laser particle size analysis, XRD, XRF, IR, TGA-DTA, SEM-EDX, Laser imaging system, µ-CT, hot-stage microscope and Factsage (8.3) thermodynamic software were used for clays and LWAs characterization in the temperature range 900–1250°C. It was found that the LWAs bloating zone occurs at 1050–1250°C with a minimum bulk density (BD) of (0.74 g/cm3) at 1250°C. During the LWAs pyroplastic state, the crystallization of anorthite from the silicate melt lowers its viscosity due mainly to the alkalis’ uptake into the anorthite lattice. However, the silicate melt is still viscous enough to trigger the reduction of hematite and consequently guarantees the evolution of bloating gases. The simultaneous association of higher evolved gas with less melt content of higher viscosity would promote the LWAs bloatability. The higher the gas that accompanied with low melt of lower viscosity would loosen the LWAs their consistency and sphericity upon their sudden cooling. Based on the LWAs bulk density and lab experimental observations, the production window limits of successful LWAs are ≥40 wt% silicate melt of 103-107 Pa.s viscosity that accompanied with (0.50–4.00 wt%) gas content. This production window has been verified by Liapor industrial kiln feed. The LWAs pyroplastic and post-quenching characteristics are all statistically significant variables (<0.05) for prediction modeling. The forecasting models are statistically verified by the multi-collinearity testing that shows VIF values <10 indicating the absence of any multi-collinearity among the models’ explanatory variables.

Investigating the grinding characteristics of vanadium-titanium iron ore tailings for sustainable utilization in cementitious material preparation

The study of the cementitious material activity of industrial solid wastes is a key issue in the comprehensive utilization of its green building materials. In this study, mechanical activation was used to prepare cementitious materials from vanadium-titanium iron ore tailings (VTIOT) as the main raw materials, and the effects of grinding time, the key parameter, on the grinding characteristics of VTIOT, the mechanical properties of the VTIOT cementitious material, and the hydration mechanism were investigated by means of surface area analysis, particle size analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), alkali leaching, mechanical testing, hydration heat analysis, and thermogravimetric analysis (TGA). The results show that: the grinding time and specific surface area of VTIOT exhibit a linear correlation. Prolonging the grinding time, the fractal dimension of the particles gradually increases. The activity of Si4+ and Al3+ elements increases rapidly, reaching a Si4+ and Al3+ content of 96 mg·L−1 at 90 min of grinding. With a VTIOT mixing amount of 30 %, a mortar paste ratio of 1:3, and a water cement ratio of 0.5, the 50 min ground VTIOT mortar demonstrates 7 d and 28 d compressive strengths of 29 MPa and 38.7 MPa, corresponding to the highest values of the activity index, measured at 71.4 % and 75.2 %, respectively. Under standard curing conditions, the hydration products of cementitious materials at 7 d are ettringite (AFt), calcium silicate hydrate (C-S-H), alumina, ferric oxide, monsulfate (AFm), calcium hydroxide (Ca(OH)2), and calcium silica (CS). In the hydration process of 7 d, the exothermic peak and exothermic amount of the 50 min VTIOT cementitious materials are greater than those observed for other grinding times, but lower than those of pure reference cement.

Moats & comets - A methodology to explore for submerged prehistory at sea floor erosional features formed at artificial reefs, Atlantic continental shelf, GeorgiaUSA.

Our primary objective is to demonstrate a method that uses marine processes, principally seafloor scour, to broadly expose prehistoric landforms and associated localities. Too often, the loss of prehistoric strata to scour processes such as ravinement during broad-scale, continental shelf transgressions, are decried without the recognition of the potential for erosion at the local scale can expose those same strata for systematic study. The analysis of sea floor erosional features formed around artificial reefs by turbulent flows in the Georgia Bight have used interferometric side-scan sonar (SSS), Remotely Operated Vehicles (ROVs), ultra-high-definition videography (UHD), and sedimentological, palynological, paleontological, archaeological analytical techniques. These techniques were integrated within a geoarchaeological methodology focused on exploring the Continental Shelf for preserved evidence of prehistoric landforms, flora and fauna once thereon. A stepwise protocol was developed to first gather interferometric side-scan sonar data to be then processed by commercial software packages such as HYPACK Hydrographic and HYSWEEP together with HYSCAN and SONAR Wiz software. The sonar mosaics were imported to ArcGIS/QGIS software to characterize scour features/targets around artificial reefs that had exposed paleo-land surfaces previously obscured by the modern palimpsest sand sheet. Analysis of scours and depressions - “moats and comets” - adjacent to reef structures were evaluated using the profile tool within the HYPACK-HYSWEEP editor package. Symbology for the bathymetric raster layers was edited to provide a clear contrast and measurement at scour features. Measured GIS images were then classified as to scour extent and depth with respect to prevailing current directions responsible for producing turbulence. A ranking of the artificial reefs by factors such as scour depth and extent was used to guide subsequent investigation by ROVs. Sediment cores and grab samples were collected, and those samples underwent particle size analysis (PSA), macro-and micro-botanical analyses. All data – geophysical, GIS, video and geological – were collated and synthesized to produce an assessment of the potential of sea floor scour features to expose previously buried geomorphological/geological, paleontological and/or archaeological features of interest.

Properties, structure and mechanism of high-temperature modified steel slag based on solid waste

In this study, a composite modifier (CMCDL) containing coal gasification residue, dicyandiamide waste slag, and lake sediments was used to modify steel slag at high-temperature. Five kind of raw materials was analyzed in physicochemical properties, mineral composition and microstructure, cementitious properties and soundness, and particle size analysis, the same to steel slag after high-temperature modification (SHTM). The new mineral phases were found that tricalcium aluminate (C3A), gehlenite (C2AS), magnetite (Fe3O4), spinels (MgFe2O4), quartz (SiO2), celite (C6AF2) and diopside (CMS2) formed in the SHTM when the mass fraction increase from 10% to 30% in CMCDL. The HTM with CMCDL increases the glass phase and hydrated mineral (C3A, C3S, C2S) and in raw steel slag, promoting the disassembled of RO phase, turning the phase from FeO into MgFe2O4 and Fe3O4. MgFe2O4 and Fe3O4 have similar crystal structures, and they form mixed spinels. When the content of CMCCL (coal gasification residue: dicyandiamide waste slag: lake sediments =7:9:4) is 20%, the temperature is 1250 °C, result showed that the mass fraction of f-CaO in SHTM using CMCCL decreases from 4.81% to 1.86%, with a decrease of 61.3%, the 28-day activity index of SHTM increases up to 17.6% compared with raw steel slag, reaching 86.2%. Therefore, the CMCDL-blended SHTM can be applied harmlessly in cement and concrete, enabling low-energy fine grinding of steel slag.

Effect of Cubic Crystal Morphology on Thermal Characteristics and Mechanical Sensitivity of PYX

To investigate the influence of the cubic crystal morphology on the thermal properties and sensitivity of 2,6-bis(picrylamino)-3,5-dinitropyridine (PYX), cubic PYX (CPYX) crystals were prepared using the antisolvent method. Scanning electron microscopy (SEM), laser particle size analysis, X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR) were used to characterize the morphology, particle size and structure of the prepared products. The thermal behavior, thermal decomposition kinetics, thermal safety parameters and thermal decomposition mechanism of CPYX were investigated by differential scanning calorimetry–thermogravimetry–mass spectrometry–Fourier transform infrared spectrometry (DSC-TG-MS-FT-IR) and in situ FT-IR experiments. Meanwhile, the mechanical sensitivity of CPYX was determined by means of the explosion probability method. The results showed that the product had a smooth cubic morphology and small crystal aspect ratio with an average particle size (d50) of 10.65 μm, but it had no distinct differences from the crystal structure of raw PYX (RPYX). The thermal decomposition peak temperature, the self-accelerating decomposition temperature and the critical temperature of the thermal explosion of CPYX increased by 7.2 °C, 6.1 °C and 10.4 °C, respectively, compared to RPYX. Similarly, the apparent activation energy increased by 15%. Besides these, the impact sensitivity and friction sensitivity of CPYX decreased by 36% and 20%, respectively, compared to RPYX. The decomposition process of CPYX contains two stages. The first stage involves the breakage of N-H bonds and -NO2 groups with the release of CO2, N2O, NO, HCN and H2O, followed by the thermal decomposition of the resulting intermediate and the release of CO2, N2O and HCN in the second stage.

Research on Formulation and Evaluation of Floating Microspheres

The purpose of this study is to design and evaluate a floating multipart oral delivery system for diltiazem hydrochloride that can provide sustained release. The aim of the work is also to study various parameters that influence the behaviour of floating multiparticles in an oral dosage form. Floating microspheres were prepared by a non-aqueous emulsifying solvent evaporation technique using ethyl cellulose and Eudragit RS-100 asthe rate-controlling polymer. In vitro activity was evaluated using standard pharmacopoeia and other tests such as drug-polymer compatibility, (%)yield, particle size analysis, drug entrapment efficiency, surface topography, in vitro buoyancy and release studies. The results show that the mixing ratio of the components in the organic phase affected the size, size distribution (199-320 µm), drug concentration(59-84%), percent yield (57-77%) and drug. Liberation microsphere (45-99aftern12 hours) and swimming time &gt; 12 hours. The best results were obtained in the ratio drug: polymer Eudragit RS-100 (1:3). Good in vitro floating behaviour was observed in most cases, and various drug release patterns could be achieved by varying the polymer ratio, which was optimized to match the target release profile. Stability studies showed no significant change in the drug content of the formulation even after 3months. The data obtained in this study therefore suggest a floating dose of micro particles

Influence of chemical pretreatment on the pozzolanicity of recycled glass microparticles used as a substitute for Portland cement

This research investigated the influence of using chemically treated glass microparticles as a partial replacement for cement in Portland cement pastes and mortars. The microparticles were obtained by grinding glass waste into three different particle size fractions (&lt; 75 µm, &lt; 45 µm, and &lt; 25 µm), treated with calcium hydroxide (CH), and characterized using SEM/EDS and a laser particle size analyzer. Samples prepared with the incorporation of glass were characterized using XRD, TGA/DTG, and SEM/EDS. The pretreatment with calcium hydroxide induced the formation of C-S-H with different morphologies on the surface of the particles, in addition to causing changes in particle size distribution due to the formation of agglomerates. The pastes prepared with treated particles had lower amounts of CH and higher levels of hydrated silicates. However, when indirectly measuring the pozzolanicity of treated particles through the compressive strength of mortars, no significant differences were observed in the strengths of mortars made with treated and untreated particles.

Application of green synthesized Ag and Cu nanoparticles for the control of bruchids and their impact on seed quality and yield in greengram

Storage pests, particularly bruchids, are major biotic constraints causing significant storage losses in pulses. Conventional control methods relying on insecticides and fumigants often lead to food contamination due to toxic pesticide residues and a rapid decline in seed germination. In this investigation, through green nano-technological application, a promising and sustainable alternative for pest management is developed. Silver and copper nanoparticles were synthesized through ocimum leaf extract. The characterization of silver and copper nanoparticles was carried out by UV-spectroscopy, particle size analyzer, scanning electron microscopy, X-ray diffraction, and Fourier-transform infrared. Both the nanoparticles were spherical and crystalline in nature. Greengram seeds were primed with standardized silver and copper nanoparticles at different concentrations (1000, 1500, and 2000 ppm) and compared with castor-treated, deltamethrin-treated, and untreated control seeds for seed quality, growth, and yield. After one month of storage, all the pulse beetles released in different treatments exhibited 100 % mortality, whereas in control, the insects multiplied. At the end of nine months, the control seeds had shown 72 % damage and 39.67 % germination. In contrast, silver nanoparticles at 1000 ppm showed no seed damage and achieved 81.67 % germination, which was on par with copper nanoparticles at 1000 ppm with 79.33 % germination. Seed priming of silver and copper nanoparticles at 1000 ppm also demonstrated superior performance in all the seed quality and biochemical parameters (alpha amylase and catalase) throughout the storage period. Whereas, in the greenhouse experiment, enhanced growth (35.96 cm, 46.48 cm, and 53.00 cm at 30, 60 DAS, and at harvest, respectively) and yield per plant (3.75 g) were significantly higher in plants that were given foliar application with silver nanoparticles at 1000 ppm. Furthermore, foliar application of these nanoparticles at all concentrations (1000, 1500, and 2000 ppm) did not exhibit any adverse effects on soil microbial organisms, as assessed by dehydrogenase enzyme activity. Hence, this research highlights the potential use of silver and copper nanoparticles at 1000 ppm as effective tools for storage pest management and contributing to improved agricultural productivity and sustainability.

Leaching kinetics of ash impurities from aphanitic graphite by combining dual-ultrasound and hydrochloric acid–potassium hydrogen fluoride

The hydrochloric acid-fluoride salt is useful for purifying graphite. Ultrasonic-assisted technique can significantly reduce the leaching time and improve the leaching efficiency. Compared with single-frequency, dual-frequency ultrasound has the advantages of high energy efficiency and wide cavitation area. In this study, the combination of a dual-frequency ultrasound-assisted technique and hydrochloric acid–potassium hydrogen fluoride leaching agent was proposed for the leaching of aphanitic graphite to remove impurity minerals. First, the effects of probe-type ultrasonic power, tank-type ultrasonic power, temperature, HCl concentration, ultrasonication time, and KHF2 concentration on the purification efficiency of impurities from aphanitic graphite with the assistance of dual-frequency ultrasound were investigated. It was found that the combination of dual-frequency ultrasound and hydrochloric acid–potassium hydrogen fluoride can reduce the ash content of aphanitic graphite from 13.02 % to 1.02 % with an ash removal rate of 94.17 %. Second, volumetric reaction models and unreacted shrinkage nucleation models were used to fit the kinetics of impurities from aphanitic graphite with dual-frequency ultrasound-assisted HCl-KHF2 leaching. Kinetic analysis shows that the volumetric reaction model with chemical control was better to fit the leaching process. This is consistent with the calculation results of the activation energy of the reaction (Ea = 58.13 kJ/mol). Finally, laser particle size analyzer, X-ray diffraction (XRD), scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDS), X-ray fluorescence spectroscopy (XRF), transmission electron microscopy-energy dispersive X-ray spectroscopy (TEM-EDS) were used to analyze the fugacity of impurity minerals during the process of dual-frequency ultrasound-assisted HCl-KHF2 leaching. It was revealed that combining ultrasonic cavitation fragmentation with chloric acid–potassium fluoride generated SiF4 with high solubility, thereby removing silica-bearing impurities more efficiently. The challenges in further reducing ash content from 1.02 % in the leached concentrate of aphanitic graphite could be attributed to the existence of titanium-bearing mineral impurities on the surface of graphite particles and the presence of silica-bearing minerals between graphite carbon layers.

Development of Sustainable Vegan Pea Protein-Zinc Complex: Characterization, In Vitro Cellular Mineral Uptake, and Application in Functional Biscuit Production

This study aimed to investigate the potential of pea protein concentrate (PPC) to form protein-mineral composites, with a specific focus on its zinc- (Zn-) binding capabilities. In addition, the physical and functional properties of PPC were evaluated. PPC, a potential protein source, was found to possess lipophilic properties, suggesting its suitability for various applications in food production. The investigation involved a comprehensive characterization of pea protein concentrate-zinc complex (PPC-Zn) composites, utilizing various analytical techniques such as Fourier transform infrared spectroscopy, scanning electron microscopy, particle size analysis, zeta potential measurement, and thermogravimetric analysis. The findings of this study indicated that the protein content of PPC-Zn (79.02 ± 1.33%) insignificantly increased as compared to PPC (78.86 ± 1.16%). Furthermore, PPC demonstrated improved functional properties, including increased protein solubility (2.55%), enhanced water-holding (13.09%) and oil-holding capacity (11.17%), and improved foaming capacity and stability (2.08% and 6.07%, respectively). These improvements in functional properties were likely attributed to the unique surface structure observed in SEM micrographs. The research also highlighted the maximum binding capacity of PPC for zinc, which was observed at concentrations of 5 mM (95.35 ± 1.86%). This binding of zinc ions to PPC induced changes in the characteristics and internal structures of the protein concentrate. Notably, the presence of functional groups such as -COOH, -OH, and –NH2 in PPC suggested their involvement in coordinating with zinc ions to form PPC-Zn composites. This investigation demonstrated a significant increase (2.26%) in the mineral bioavailability of PPC-Zn. Additionally, the cellular uptake, retention, and transport of PPC-Zn were improved by 9.79%, 7.84%, and 9.51%, respectively. Fortified biscuits (B2) demonstrated enhanced cellular uptake (2.79%), retention (4.84%), and transport (3.51%) compared with control biscuits. Fortified biscuits (B2) had higher microbial counts (total plate count is 3.57 ± 0.03 and the yeast-mold count is 3.96 ± 0.07 cfu/g) than control biscuits (B1) (total plate count is 2.49 ± 0.13 and the yeast-mold count is 3.44 ± 0.11 cfu/g) at the end of storage, and there is no difference in sensory evaluation between the control and fortified biscuits. Furthermore, the key findings indicated that PPC could serve as a promising carrier for mineral supplements, binding with zinc effectively.

Green Synthesis and Characterization of CuO, Fe2O3 and CuO/Fe2O3 Compounds Investigation

Green chemistry techniques are increasingly being used to produce nanomaterials from easily accessible natural resources. The present study utilized a cost-effective and environmentally sustainable method to separately synthesize copper oxide, iron oxide, and mixed oxide nanoparticles. Copper (II) nitrate trihydrate and iron (III) nitrate nonahydrate were utilized as precursors with the help of fruit peel extracts. The nano-oxides were synthesized from the local fruit peels, specifically orange, cherry, and sidra (Ziziphus jujuba), by a simple procedure that involved heating the peels with distilled water, filtration, adding precursor, and calcination. Experiments were conducted on the resultant powders to evaluate their structural, biological, and physical characteristics. The results of the X-ray diffraction analysis showed that pure crystallite structures of CuO and Fe2O3 were formed, ternary compound CuFeO2 (delafossite), and CuO / Fe2O3 (nanocomposite) were synthesized, and their purity was verified through energy dispersive X-rays (EDX). The findings from scanning electron microscopy (SEM) and particle size analysis (PSA) revealed that the nanoparticles are semi-spherical, with particle sizes ranging from 83.9 to 118.7 nm for CuO, from 95.2 to 119.8 nm for Fe2O3, and from 60.6 to 90.4 nm for mixed oxides extracted from three fruit peels. The conducted experiments on bacterial and fungal resistance revealed that the produced oxides are effective antibacterial and antifungal particles. The synthesized nanoparticles were also analysed through AFM and Toxicity.

Insight into the interaction and binding mechanism of a natural nonnutritive sweetener mogroside V with soybean protein isolates based on multi-spectroscopic techniques and computational simulations

As a natural low-calorie sweetener, Mogroside V (Mog-V) has gradually become one of the alternatives to sucrose with superior health attributes. However, Mog-V will bring unpleasant aftertastes when exceeding a threshold concentration. To investigate the possibility of soy protein isolates (SPIs), namely β-conglycinin (7S), and glycinin (11S) as flavor-improving agents of Mog-V, the binding mechanism between Mog-V and SPIs was explored through multi-spectroscopy, particle size, zeta potential, and computational simulation. The results of the multi-spectroscopic experiments indicated that Mog-V enhanced the fluorescence of 7S/11S protein in a static mode. The binding affinity of 7S-Mog-V was greater compared with 11S-Mog-V. Particle size and zeta potential analysis revealed that the interaction could promote aggregation of 7S/11S protein with different stability. Furthermore, computational simulations further confirmed that Mog-V could interact with the 7S/11S protein in different ways. This research provides a theoretical foundation for the development and application of SPI to improve the flavor of Mog-V, opening a new avenue for further expanding the market demand for Mog-V.

The Preparation of Crumpled Graphene Oxide Balls and Research in Tribological Properties.

In this study, crumpled graphene oxide balls (CGBs) were prepared via capillary compression using a rapidly evaporating aerosol droplet method. The CGBs were observed using scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), and Raman spectroscopy. The size distributions of crumpled particles were obtained using a laser nanometer particle size analyzer (DLS). The dispersibility of the water and the ionic liquid (IL) was tested by ultrasonic dispersion. The tribological properties of water or ionic liquids containing crumpled graphene oxide ball additives (W/IL-CGB) were tested by a reciprocating friction tester and compared with water/ionic liquids with graphene oxide. The morphology of the wear scar was observed by a three-dimensional optical microscope and its lubrication mechanism was analyzed. The results show that the CGBs were successfully prepared by rapid evaporation of aerosol droplets, and the obtained CGBs were crumpled paper spheres. The CGBs had good water dispersion and ionic liquid dispersion, and IL-CGB has excellent anti-friction and anti-wear effects on steel-steel friction pairs. During the friction process, the CGB was adsorbed at the interface of the steel-steel friction pair to form a protective layer, which avoids the direct contact of the friction pair, thereby reducing friction and wear.

Investigating the depositional environments using particle-size analysis of Lower Cretaceous sandstone reservoirs, Biyadh Formation, Saudi Arabia

This study employed particle-size analysis on twenty friable sandstone beds from two outcrops of the Biyadh Formation, which acts as a water aquifer, petroleum reservoir, and CO2 capturing reservoir. Hydrodynamic processes and depositional environments were identified using bivariate plots, Visher diagrams, Passega diagrams, and linear discriminant functions (LDF). The results reveal that the beds of Outcrop A mainly consist of medium- to well-sorted, medium-grained sandstone that is near-symmetrical and mesokurtic. However, Outcrop B comprises medium-sorted, medium-grained sandstone beds that are near-symmetrical and leptokurtic. All the beds in Outcrop A and B are unimodal. Furthermore, Visher and Passega diagrams indicate that the particles of Outcrop A were mostly transported by rolling, saltation, and suspension. In contrast, the particles of Outcrop B were transported by rolling, saltation, suspension, and graded suspension. The LDF technique shows that the depositional environments were beach, aeolian, fluvial, and shallow marine.

Synthesis and Characterization of Novel Zirconium Incorporated Pectin-Based Citric Acid Crosslinked Nanoparticles

Synthesis and Characterization of Novel Zirconium Incorporated Pectin-Based Citric Acid Crosslinked Nanoparticles

Nanoplastic Size and Surface Chemistry Dictate Decoration by Human Saliva Proteins.

Environmental pollution with plastic polymers has become a global problem, leaving no continent and habitat unaffected. Plastic waste is broken down into smaller parts by environmental factors, which generate micro- and nanoplastic particles (MNPPs), ultimately ending up in the human food chain. Before entering the human body, MNPPs make their first contact with saliva in the human mouth. However, it is unknown what proteins attach to plastic particles and whether such protein corona formation is affected by the particle's biophysical properties. To this end, we employed polystyrene MNPPs of two different sizes and three different charges and incubated them individually with saliva donated by healthy human volunteers. Particle zeta potential and size analyses were performed using dynamic light scattering complemented by nanoliquid chromatography high-resolution mass spectrometry (nLC/HRMS) to qualitatively and quantitatively reveal the protein soft and hard corona for each particle type. Notably, protein profiles and relative quantities were dictated by plastic particle size and charge, which in turn affected their hydrodynamic size, polydispersity, and zeta potential. Strikingly, we provide evidence of the latter to be dynamic processes depending on exposure times. Smaller particles seemed to be more reactive with the surrounding proteins, and cultures of the particles with five different cell lines (HeLa, HEK293, A549, HepG2, and HaCaT) indicated protein corona effects on cellular metabolic activity and genotoxicity. In summary, our data suggest nanoplastic size and surface chemistry dictate the decoration by human saliva proteins, with important implications for MNPP uptake in humans.

Effect of Polyoxyethylene-Based Nonionic Surfactants on Chemical–Mechanical Polishing Performance of Monocrystalline Silicon Wafers

Effect of Polyoxyethylene-Based Nonionic Surfactants on Chemical–Mechanical Polishing Performance of Monocrystalline Silicon Wafers

Hypoxic adipose stem cell-derived exosomes carrying high-abundant USP22 facilitate cutaneous wound healing through stabilizing HIF-1α and upregulating lncRNA H19.

Hypoxic preconditioning has been recognized as a promotive factor for accelerating cutaneous wound healing. Our previous study uncovered that exosomal lncRNA H19, derived from adipose-derived stem cells (ADSCs), plays a crucial role in orchestrating cutaneous wound healing. Herein, we aimed to explore whether there is a connection between hypoxia and ADSC-derived exosomes (ADSCs-exos) in cutaneous wound healing. Exosomes extracted from ADSCs under normoxic and hypoxic conditions were identified using transmission electron microscope (TEM) and particle size analysis. The effects of ADSCs-exos on the proliferation, migration, and angiogenesis of human umbilical vein endothelial cells (HUVECs) were evaluated by CCK-8, EdU, wound healing, and tube formation assays. Expression patterns of H19, HIF-1α, and USP22 were measured. Co-immunoprecipitation, chromatin immunoprecipitation, ubiquitination, and luciferase reporter assays were conducted to confirm the USP22/HIF-1α/H19 axis, which was further validated in a mice model of skin wound. Exosomes extracted from hypoxia-treated ADSCs (termed as H-ADSCs-exos) significantly increased cell proliferation, migration, and angiogenesis in H2O2-exposed HUVECs, and promoted cutaneous wound healing invivo. Moreover, H-ADSCs and H-ADSCs-exos, which exhibited higher levels of H19, were found to be transcriptionally activated by HIF-1α. Mechanically, H-ADSCs carrying USP22 accounted for deubiquitinating and stabilizing HIF-1α. Additionally, H-ADSCs-exos improved cell proliferation, migration, and angiogenesis in H2O2-triggered HUVECs by activating USP22/HIF-1α axis and promoting H19 expression, which may provide a new clue for the clinical treatment of cutaneous wound healing.

Preparation and Biological Activity Studies of Octenyl Succinic Anhydride Starch-Based Emulsions Containing Natural Essential Oils and Their Components

In this study, clove essential oil (CL), eugenol (EU), and cinnamaldehyde (CI) were immobilized in starch sodium octenyl succinate (SSO) using an emulsification method. The main characteristics, stability, and biological properties of the prepared emulsions were established. Particle size analyses using dynamic light scattering showed that the smaller droplets were characteristic of emulsions containing CI (205–218 nm) and EU (181–236 nm), while the largest droplets were determined for CL emulsions (293–348 nm). Moreover, the highest antioxidant activity was determined for CL (79–83%) and EU (80–88%) emulsions, while CI emulsions showed the greatest antibacterial activity. The obtained emulsions were applied to the paper sheets and the bioactive properties of coated paper were studied. Evaluation of antioxidant properties revealed that high antioxidant activity reaching 76–92% and 87–91% was characteristic of coatings containing CL and EU, respectively. Meanwhile, coatings containing CI showed quite low antioxidant activity (4–9%) but demonstrated the greatest antimicrobial effect on Gram-negative and Gram-positive bacteria as well as yeasts. Hence, CL and EU emulsions could be used as effective natural antioxidants, whereas CI emulsions could be applied as an antimicrobial agent on cellulose-based substrates for a wide range of human health protection applications.