Surface Parameters Research Articles

Preparation of super-hydrophobic BN nanotube mesh and theoretical research of wetting state

In this study, we have fabricated stainless steel mesh with columnar super-hydrophobic boron nitride nanotubes (BNNTs) through the ‘gas-liquid-solid’ mechanism annealing method. We employed iron (Fe) powder as the catalyst and utilized boron (B) and boron oxide (B2O3) as the raw materials. The synthesis took place within a tubular furnace, operating under an NH3 atmosphere at a temperature of 1250C∘. The contact angle of water droplets on the experimental surface measures approximately 150∘, while the sliding angle is approximately 3∘. In the next place, the laboratory carried out a series of experiments on the tensile properties, corrosion resistance, and erosion resistance of the prepared samples. The experimental results showed that the sample material had good mechanical properties and corrosion resistance. In addition, the erosion resistance test results showed that the sample material even at high speed (2800 rpm/min). After washing the sample for 5 min, the surface of the material still has good wettability (contact angle is 136.49∘). Finally, droplet bouncing experiments have demonstrated that the adhesion force on the surface of the boron nitride nanotube stainless steel mesh is notably minimal, indicating its substantial hydrophobic properties. Additionally, we conducted an investigation into the wetting interaction between droplets and the surface of the boron nitride nanotube stainless steel mesh. By applying the Wenzel and Cassie formulas and considering the pertinent geometric parameters of the material surface, we theoretically elucidated that, upon contact, the droplets assume a ‘Cassie’ state on the surface of the super-hydrophobic boron nitride nanotube stainless steel mesh. The research results show that the superhydrophobic boron nitride nanotube stainless steel mesh has broad application prospects in the fields of hydrogen storage, sewage treatment and oil-water separation.

Effect of TiO2 Abutment Coatings on Peri-Implant Soft Tissue Behavior: A Systematic Review of In Vivo Studies.

Establishing a proper soft tissue adhesion around the implant abutment is essential to prevent microbial invasion, inhibit epithelial downgrowth, and obtain an optimal healing process. This systematic review aims to evaluate the real potential of TiO2 coating on the behavior of peri-implant soft tissue health and maintenance. A specific aim was to evaluate clinically and histologically the effect of TiO2 abutment coating on epithelial and connective tissue attachment. Electronic database searches were conducted from 1990 to 2023 in MEDLINE/PubMed and the Web of Science databases. In total, 15 out of 485 publications were included. Eight studies involved humans, and seven were animal studies. Exposure time ranges from 2 days to 5 years. The peri-implant soft tissue evaluations included clinical assessment (plaque index (PI), peri-implant probing pocket depth (PPD), and bleeding on probing (BoP)), histological as well as histomorphometric analysis. The Office of Health Assessment and Translation (OHAT) Risk of Bias Rating Tool for Human and Animal Studies was used to evaluate the overall quality of the studies included in the review. The results showed some variation but remained within acceptable limits. Within the limitations of this systematic review, the present findings suggest that TiO2 coatings seem to influence soft tissue healing. TiO2-coated abutments with a roughness value between 0.2 and 0.5 μm enhance soft tissue health. Sol-gel-derived TiO2 coatings induced better soft tissue attachment than noncoated machined abutment surfaces. The anodized titanium abutments demonstrate comparable clinical and histological outcomes to conventional machined abutments. However, there was variation among the included studies concerning TiO2 coating characteristics and the measured outcomes used to evaluate the soft tissue response, and therefore, quantitative analysis was not feasible. Long-term in vivo studies with standardized soft tissue analysis and coating surface parameters are necessary before a definitive conclusion can be drawn. OSF Registration No.: 10.17605/OSF.IO/E5RQV.

Quantitative evaluation of morphological and functional changes in meibomian glands and lipid layer thickness in patients with and without keratoconus.

To quantitatively evaluate the morphological parameters of meibomian glands (MGs) and lipid layer thickness (LLT) in patients with keratoconus (KC). In this prospective, cross-sectional study, 164 eyes of 164 keratoconus patients and 64 eyes of 64 age-matched control subjects were included. An advanced automatic MG analyzer was used to quantitatively measure the morphological and functional parameters of MGs. Morphological and functional parameters of MGs, LLT, and other ocular surface parameters were compared between the control and KC groups. The mean meibomian gland diameter, length, square, and gland area ratio (GA) were all significantly decreased in the KC group (all P < 0.05), while no significant difference was observed in the gland tortuosity index (TI) and gland signal index (SI) between the KC and control groups (all P > 0.05). There was no significant difference in the number of total and incomplete blinking among patients with different stages of keratoconus (all P > 0.05). The gland diameter, square, and TI were all negatively associated with KC severity (all P < 0.05), while no significant difference was observed among all stages of KC in gland length, GA, and SI (all P > 0.05). Moreover, the LLTs were positively correlated with the gland diameter, square, GA, and TI and negatively correlated with anterior corneal curvature or KC severity (all P < 0.05). Atrophic morphological changes in the meibomian glands were closely correlated with the severity of keratoconus. Gland diameter may be a sensitive functional morphology metric of meibomian glands in patients with keratoconus.

Improving the Asian dust storm prediction using WRF-Chem through combinational optimization of physical parameterization schemes

This study aims to enhance the accuracy of the Weather Research and Forecasting model coupled with Chemistry (WRF-Chem) in forecasting Asian dust storms (ADSs) by using the micro-Genetic Algorithm (μGA). We developed an optimization system---the WRF-Chem-μGA system---to seek the optimal combination of the planetary boundary layer (PBL) and land surface parameterization schemes, which are crucial for numerical forecast of dust storms. The optimization was conducted concerning meteorological and air quality variables, i.e., aerosol optical depth, PBL height, 2 m temperature, 2 m relative humidity, and 10 m wind speed, simultaneously for three ADS cases over the optimization domain, including South Korea. Among a total of 32 available combinations of physical parameterization scheme options (8 from PBL and 4 from land surface schemes), the optimized set through the WRF-Chem-μGA system consists of the Asymmetrical Convective Model version 2 (ACM2) for the PBL scheme and the Noah land surface model with Multiple Parameterization options (Noah-MP) for the land surface scheme. The optimized set showed an improvement ratio of up to 22.5 % in terms of the normalized RMSE for all meteorological and air quality variables, compared to various non-optimized sets of physical parameterization schemes for two additional ADS cases. The optimal set proposed in this study can be used comprehensively in numerical forecasts of various meteorological and air quality problems in the East Asian region, using the WRF-Chem model.

Unravelling the influence of surface functional groups and surface charge on heavy metal adsorption onto carbonaceous materials: An in-depth DFT study

Theoretical analyses were explored for the adsorption of heavy metals in aqueous systems, focusing on the influence of surface charge and functional groups of carbonaceous materials. The approach involved the meticulous assignment and interpretation of active adsorption bands, achieved through modelling of Fourier Transform Infrared (FT-IR) and X-ray Photoelectron Spectroscopy (XPS) spectra. Additionally, atomic charges were analyzed, utilizing their chemical properties to glean valuable insights into the atomic-level intricacies of the adsorption process. The structural parameters of the carbonaceous surface reveal that in unsaturated models, heavy metals preferentially adsorb onto neighboring carbons due to facilitated electron transfer. Conversely, adsorption predominantly occurs in saturated models within functional groups, except for interactions involving the phenolic group, where it occurs on the carbonaceous matrix. Overall, negative ΔG values were observed across a range of temperatures from 285 to 315 K, as evidenced by Gibbs free energy values ranging from −72.93 kcal/mol (Ni2+ on carboxylate) to −4.98 kcal/mol (Cd2+ on ketone), confirming the spontaneous and thermodynamic feasibility nature of the adsorption processes for heavy metals on biochar across all evaluated functional groups, following the trend Ni2+ > Zn2+ > Co2+ > Cd2+. These trends can be rationalized in terms of: a) the size-dependence, where smaller cations such as Ni2+ (0.69 Å) form more stable adsorption complexes than Cd2+ (0.95 Å); b) charge transfer, higher adsorption energy (-55.60 kcal/mol) corresponds to a greater magnitude of charge transfer (0.32e); and c) the electronegativity of the respective metals, which are as follows: 1.367 for Ni2+, 1.349 for Co2+ and 1.336 for Zn2+. Consequently, Ni2+ exhibits a greater propensity to accept electrons from oxygen biochar than Co2+ and Zn2+ atoms. Finally, the assignment of IR and XPS is challenging in the laboratory, facing several endeavours. Our findings indicate a notable shift in the C―O stretching signal from 1631 cm−1 (in the clean system) to 1652 cm−1 upon Cd2+ adsorption, with Co2+, Ni2+, and Zn2+ showing shifts to 1690 cm−1 and 1685 cm−1 for the latter two cases, respectively. Therefore, the theoretical signals reported in the current work are a helpful tool as benchmark data to address and complement further experimental information. Indeed, the modelling of IR and XPS fit with some experimental values for some representative cases, implying appropriate modelling of the above systems.

Clinical study of the cytokine panel in the diagnosis of ocular chronic graft-versus-host disease

Objective: To investigate the association between cytokines and ocular chronic graft-versus-host disease (cGVHD) and identify specific biomarkers for ocular cGVHD to enhance clinical diagnosis, treatment, and evaluation. Methods: A mouse model of cGVHD was established to explore the correlation between cGVHD and serum cytokines. Based on the findings from the animal experiments and literature review, a panel of 16 cytokine combinations was identified. Enzyme-linked immunosorbent assay (ELISA) was used to compare the cytokine concentrations in the serum and tear samples from patients who underwent allogeneic hematopoietic stem cell transplantation from June 2017 to March 2022 at the Medical Center of Hematology, Xinqiao Hospital, Army Medical University. Results: ① Compared with the control group, mice with cGVHD exhibited elevated serum IL-1β, IL-6, IL-8, IL-17, IFN-γ, CX3CL1, CXCL11, CXCL13, CCL11, and CCL19 concentrations (all P<0.05). ② Analysis of the cytokine profiles of the serum and tear samples revealed that compared with patients without ocular cGVHD, those with ocular cGVHD exhibited increased serum IL-8 [P=0.032, area under the curve (AUC) =0.678]; decreased serum IL-10 (P=0.030, AUC=0.701) ; elevated IL-8, IFN-γ, CXCL9, and CCL17 in tear samples; and lower IL-10 and CCL19 in tear samples (all P<0.05, all AUC>0.7). Moreover, cytokines in tear samples showed correlations with ocular surface parameters related to ocular cGVHD. Conclusions: Tear fluid demonstrates greater specificity and sensitivity as a biomarker for diagnosing ocular cGVHD than serum biomarkers. Among the identified cytokines in tear samples, IL-8, IL-10, IFN-γ, CXCL9, CCL17, and CCL19 serve as diagnostic biomarkers for ocular cGVHD post-transplantation, offering practical reference value for diagnosis.

Thermal Transitions and Structural Characteristics of Poly(3,4-ethylenedioxythiophene/cucurbit[7]uril) Polypseudorotaxane and Polyrotaxane Thin Films.

Herein, we report the thermal transitions and structural properties of poly(3,4-ethylenedioxythiophene/cucurbit[7]uril) pseudopolyrotaxane (PEDOT∙CB7-PS) and polyrotaxane (PEDOT∙CB7-PR) thin films compared with those of pristine PEDOT. The structural characteristics were investigated by using variable-temperature spectroscopic ellipsometry (VTSE), differential scanning calorimetry (DSC), X-ray diffraction (XRD) and atomic force microscopy (AFM). VTSE and DSC results indicated the presence of an endothermic process and glass transition in the PEDOT∙CB7-PS and PEDOT∙CB7-PR thin films. X-ray diffraction of PEDOT∙CB7-PS and PEDOT∙CB7-PR powders displayed the presence of interchain π-π stacking revealing a characteristic arrangement of aromatic rings in the internal structure of the crystallites. AFM imaging of PEDOT∙CB7-PS and PEDOT∙CB7-PR thin films exhibited significant differences in the surface topographies compared with those of PEDOT. A high degree of crystallization was clearly visible on the surface of the PEDOT layer, whereas the PEDOT∙CB7-PS and PEDOT∙CB7-PR thin films exhibited more favorable surface parameters. Such significant differences identified in the surface morphology of the investigated layers can, therefore, be clearly associated with the presence of surrounding CB7 on PEDOT skeletons.

Validation of a 3D Local-Scale Adaptive Solar Radiation Model by Using Pyranometer Measurements and a High-Resolution Digital Elevation Model.

The result of the multidisciplinary collaboration of researchers from different areas of knowledge to validate a solar radiation model is presented. The MAPsol is a 3D local-scale adaptive solar radiation model that allows us to estimate direct, diffuse, and reflected irradiance for clear sky conditions. The model includes the adaptation of the mesh to complex orography and albedo, and considers the shadows cast by the terrain and buildings. The surface mesh generation is based on surface refinement, smoothing and parameterization techniques and allows the generation of high-quality adapted meshes with a reasonable number of elements. Another key aspect of the paper is the generation of a high-resolution digital elevation model (DEM). This high-resolution DEM is constructed from LiDAR data, and its resolution is two times more accurate than the publicly available DEMs. The validation process uses direct and global solar irradiance data obtained from pyranometers at the University of Salamanca located in an urban area affected by systematic shading from nearby buildings. This work provides an efficient protocol for studying solar resources, with particular emphasis on areas of complex orography and dense buildings where shadows can potentially make solar energy production facilities less efficient.

A 3D Computational Model of Nanosecond Pulsed Laser Texturing of Metals for Designing Engineered Surfaces

Abstract Laser surface texturing uses a pulsed laser that is scanned on the surface, wherein each pulse creates a micro-crater through material ablation. A variety of textures can be generated depending on the laser parameters and the overlap of the laser spots. This work presents a computational model that can predict the topography of a textured surface produced using a nanosecond pulsed laser. The model involves a multi-physics approach that considers laser ablation with plasma effects and the melt pool’s fluid dynamics to obtain the crater profile for a single pulse. The 3D surface profile created from the multi-physics model is mathematically superimposed to mimic the spatial overlapping of multiple pulses. The model predicts surface topography when a laser is scanned along a linear track with successive overlapping tracks. The experiments have confirmed that the proposed model has an accuracy greater than 90% in predicting surface roughness (Sa), as well as volume parameters such as core void volume (Vvc) and valley void volume (Vvv). It was observed that the variation of these surface characteristics is highly non-linear with the process parameters. Furthermore, the model is used to design engineered surfaces to modify friction coefficient, adhesion, and leakage probability. It is demonstrated that the surface parameters for functional requirements can be modified significantly just by varying the overlap of the laser spots in different directions. The proposed model can be used to create textured surfaces for various applications through an appropriate choice of laser parameters and scanning parameters.

Divergent Responses of Summer Terrestrial Evapotranspiration to Cloud Increase in East Asia

AbstractCloud impact on terrestrial evapotranspiration (ET) can be significant, while a fundamental understanding of ET response to cloud change has not been addressed in regional aspects. In this study, seven ET datasets from satellite and land surface models are used to analyze the summer ET in response to low cloud cover (LCC) over East Asia, in combination with satellite microwave and optical vegetation data, as well as ERA5 climatic and surface parameters. In general, all ET datasets present a strong negative relationship with LCC over dense vegetation (e.g., forests), which leads to the ET reduction of more than −0.5 mmday−1 under the large LCC increase, compared with the least cloudy sky conditions. Such reduction is stronger under more humid and denser forests (aridity index AI &gt; 0.5 and enhanced vegetation index EVI &gt; 0.6). In contrast, a positive relationship between ET and LCC presents over arid and sparse lands (AI &lt; 0.2 and EVI &lt; 0.2), accompanied by enhanced ET (&gt;0.2 mmday−1). Analysis shows that under increased LCC conditions, substantial reduction in radiation availability results in the decline in both plant transpiration (ETveg) and soil evaporation (ETsoil) over humid dense vegetation, dominating the overall negative response. The increase of near‐surface relative humidity over arid sparse vegetation may indicate a stronger moisture availability, which promotes ETsoil and partly offsets the negative effect of radiation reduction. The change of vegetation water content, indicated by a satellite microwave vegetation index, is important for ETveg over arid mountainous lands with cloud cover. These findings contribute new insights to the understanding of vegetation‐atmosphere interactions.

Comparison of COSMO and ICON-LAM high-resolution numerical forecast for Romanian territory: Case studies and evaluation

This paper aims to offer the first detailed inter-comparison of the performance from the numerical weather prediction models Consortium for Small-scale Modeling (COSMO) and Icosahedral Nonhydrostatic General Circulation Model, Limited Area Mode (ICON-LAM), integrated for the Romanian territory at the horizontal resolution of 2.8 km. As the ICON numerical model is set to replace COSMO, a comparison is carried out between the operational configurations of the two models. First, two cases with severe weather (strong atmospheric instability, observed heavy precipitation, and strong wind) are analyzed: February 3-6, 2020 (heavy precipitation [snow] and very strong wind) and May 3-5, 2020 (heavy precipitation). This is followed by a statistical inter-comparison between the two models for the summer of 2020 (June, July, August). A statistical evaluation of the forecast quality from the two models is performed objectively, through statistical scores computed using surface observations from all available meteorological stations on the Romanian territory. Stratifications depending on station altitude and location are carried out, with emphasis on stations of particular interest, depending on the evolution of the synoptic situation. Following the statistical evaluation, results for the precipitation forecast do not show significant improvement in favor of either model. However, ICON-2.8 km mostly outperforms COSMO-2.8 km for surface parameters.

A novel fracture criterion for elastic‐brittle cracked body under compression and shear conditions

AbstractWhen the elastic‐brittle cracked body is subjected to compressive‐shear loading, not only does the phenomenon of wing crack initiation and propagation occur, but there is also a notable incidence of secondary crack initiation and propagation due to shear stress. Moreover, the shear fracture toughness (KIIc) predicted by the fracture criterion in the framework of classical fracture mechanics is usually smaller than the tensile fracture toughness (KIc), which is inconsistent with the actual observations. Therefore, this research firstly establishes a mechanical model of an elastic‐brittle cracked body under biaxial compression considering three kinds of crack parameters and materials' mechanical properties. Then, the stress field characteristics at the crack tip are analyzed. Next, a compression‐shear mixed fracture criterion is proposed. Finally, the effects of the lateral pressure coefficient (λ), critical plastic zone size (rc), friction coefficient (f), and deformation parameters of the crack surface on the failure modes at the crack tip are investigated.

The Macroscopic Measurement Of The Liver And Kidney Of Male Mice (Rattus Norvegicus Berkenhout) Treated With Neptunia Plena Lour Leaf Extract

The Supan Supan Laki plant (N. plena Lour) has been used traditionally by a group of people in Pal Batu Village, Paminggir District, North Hulu Sungai Regency as a herbal medicine to increase male sexual activity. Based on previous research, this plant has been proven to have a positive effect in increasing fertility in test animals. However, until now, there is no certainty regarding the safety of using this plant. This study aims to examine the effects and safety of consuming Supan Supan Laki extract on the macroscopic appearance of the liver and kidneys in mice. This research was carried out, there were four treatment groups in this study, namely Na-CMC 0.5%; 87.5mg/KgBW; 175mg/KgBW; and 350mg/KgBW, given for 28 days using a Completely Randomized Design (CRD) trial design. On the 29th day, surgery was performed to observe the liver and kidney macroscopically. Measurement of color, surface and relative organ weight parameters of the kidneys and liver of mice. The results of the study showed that administration of Supan Supan Laki leaf extract caused significant changes in the macroscopic appearance of the liver and kidney organs. In the research analysis using the One Way Anova test, the results of the test showed that the liver (p&gt;0.05) did not have a significant level of variation, while the kidney (p&lt;0.05) had a significant level of variation so that it could be concluded that the effect of N.plena Lour leaf extract have different effects on the relative weight of the heart and kidney organs.

Study on the influence of pore water pressure on shear mechanical properties and fracture surface morphology of sandstone

To further investigate the weakening effect of pore water pressure on intact rock mechanics properties and characteristics of fracture surface after failure, direct shear tests of sandstone were conducted under different pore pressure. A 3D scanner was employed to digitize the morphology of the post-shear fracture surface. The variogram function was applied to quantify the anisotropic characteristics of post-shear fracture surface. The relationship between deformation during shear failure of intact rock and quantitative parameters of fracture surface after shear failure was initially established. It can be found that amplitudes of the sinusoidal surface determine the maximum value of variogram, and period affect lag distance that reach the maximum value of variogram. Test results revealed that the increase of pore pressure has obvious weakening effect on shear strength and deformation of rock. Moreover, the increase of pore pressure makes the shear fracture surface flatter. It can be obtained that both Sillmax and Rangemax are positively related to shear strain, but negatively related to normal strain.

Field Telemetry Drilling Dataset Modeling with Multivariable Regression, Group Method Data Handling, Artificial Neural Network, and the Proposed Group-Method-Data-Handling-Featured Artificial Neural Network

This paper presents data-driven modeling and a results analysis. Group method data handling (GMDH), multivariable regression (MVR), artificial neuron network (ANN), and new proposed GMDH-featured ANN machine learning algorithms were implemented to model a field telemetry equivalent mud circulating density (ECD) dataset based on surface and subsurface drilling parameters. Unlike the standard GMDH-ANN model, the proposed GMDH-featured ANN utilizes a fully connected network. Based on the considered eighteen experimental modeling designs, all the GMDH regression results showed higher R-squared and minimum mean-square error values than the multivariable regression results. In addition, out of the considered eight experimental designs, the GMDH-ANN model predicts about 37.5% of the experiments correctly, while both algorithms have shown similar results for the remaining experiments. However, further testing with diverse datasets is necessary for better evaluation.

Study on gear contact stiffness and backlash of harmonic drive based on fractal theory

Contact stiffness and backlash in the harmonic drive significantly impact a robot's positioning accuracy and vibration characteristics. The height of the harmonic drive tooth pair is typically less than 1 mm, making the measurement and modeling of backlash and contact stiffness inherently complex. This paper proposes a contact stiffness and backlash model by establishing a correlation between fractal parameters and tooth contact load. To obtain the fractal roughness parameters of the real machined tooth surface, a combination of a noncontact optical profiler and the RMS method is employed. Subsequently, the study explores the influence of rough tooth surface and contact force fractal parameters on contact stiffness and gear backlash. The results demonstrate the substantial impact of surface topography parameters and contact force on contact stiffness and backlash. Specifically, an increase in the fractal dimension correlates with a reduction in gear backlash and contact stiffness. Conversely, the fractal roughness parameter exhibits the opposite effect. Notably, an increase in contact force enhances contact stiffness.

Time-varying stretching velocity analysis for an unsteady flow of Williamson fluid by Hermite wavelet

This study investigates unsteady velocity Uw=ξx/t\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${U}_{w}=\\xi x/t$$\\end{document} for a Williamson nanofluid film flowing over a moving surface. This work can be used to outline the effects of an applied angled magnetic-field on liquid film flow, which occurs in numerous real-world solicitations such as coating industries for wire or sheet, labs, painting, and several others. Analyzing williamson nanoliquid film flow over a stretching sheet is the main aim of this investigation. The leading Navier–Stokes models are reduced to third-order nonlinear ODE through similarity transformations that are then undertaken using the Hermite wavelet method (HWM). Both 2-dimensional and axisymmetric film flow circumstances have been analyzed. The moving surface parameter ξ\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\xi$$\\end{document} is said to have a limited range for which the solution exists. Specifically, ξ≤-1/4\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\xi \\le -1/4$$\\end{document} for axisymmetric flow and ξ≥-1/2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\xi \\ge -1/2$$\\end{document} for two-dimensional flow. Before decreasing to the boundary condition, the velocity climbs until it reaches its maximum. By taking into account the stretching (ξ>0\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\xi >0$$\\end{document}) and shrinking (ξ<0\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\xi <0$$\\end{document}) wall conditions, streamlines are also examined for axisymmetric and 2-dimensional flow patterns.

Synthesis, self-aggregation, thermal stability and cytotoxicity trends of alkyloxypropoxycyclohexane based pyridinium ionic liquids

New ether-functionalized pyridinium ionic liquids (ILs) has been synthesized by simple methodology and described by different spectroscopic techniques. Presence of two positional isomers has been confirmed with the help of NMR spectroscopy. The critical micelle concentration and other surface parameters of these ILs were deduced by conductivity, surface tension and fluorescence method. A collection of useful physical parameters i.e. critical micelle concentration (cmc), surface tension accomplished at cmc (γcmc), effectiveness of diminution in surface tension (Πcmc), maximum surface excess concentration (Ʈmax) and minimum surface area per molecule (Amin) at the air–water interface were also estimated. The average size of aggregates formed by investigated pyridinium ILs have been well examined by dynamic light scattering (DLS) experiments. The thermal degradation analysis of the present ILs has also been suggested that these ILs possessed thermal stability ranges from 200 °C to 240 °C. The investigated ILs have also been tested by MTT assay (3-(4, 5-dimethylthiazol-2-yl)-2, 5-diphenyltetrazolium bromide) on the C6 glioma cell line and found to revealed very low cytotoxicity in the concentration range required for biomedical applications. Such a low cytotoxicity of present ILs opens several new applications in the many biological purposes like drug and gene delivery agents. The physical study of investigated ILs indicate that the presence of ether functionality and varying hydrophobic chain length significantly altered the physicochemical properties of these pyridinium ILs than related to earlier synthesized N-(cyclohexanoxycarbonylmethyl) and 3-Cyclohexyloxy-2-Hydroxypropyl Pyridinium and Imidazolium surface active ILs.

Evaluation of visual field and ocular surface parameters by clinical comparison after blepharoplasty for dermatochalasis

To evaluate the effect of upper eyelid blepharoplasty surgery on corneal topography, visual field, ocular surface, meibography, corneal biomechanics and dry eye parameters. This prospective study included a total 80 eyes of 40 patients. Following a detailed ophthalmological examination, standardized patient satisfaction questions were posed to patients before and after upper eyelid blepharoplasty surgery. Visual field test, non-invasive break up time (NIBUT), meibography, and corneal topography parameters were analyzed and evaluated. The mean (+) visible areas in the visual field were found to be 46.20±24.96 preoperatively, 56.73±21.98 at the 1st postoperative month and 65.96±18.5 at the 3rd month, which were statistically significant. NIBUT values preoperatively, at 1 month and at 3 months were 11.26±4.48, 11.16±4.5 and 10.14±4.0, respectively, which were statistically significant. Meibomian gland loss rates on meibography preoperatively and postoperatively at 1 and 3 months were found to be 30.24±8.3, 29.36±8.2 and 28.22±7.7 respectively and were statistically significant. With the scoring system after blepharoplasty, patients reported improvement in their symptoms. Upper eyelid blepharoplasty surgery is predicted to increase the quality of vision. It was observed that there was a functional and cosmetic improvement in the complaints of the patients after blepharoplasty. However, blepharoplasty may cause changes in eyelid dynamics and cause dry eye syndrome.

Optimizing freeform lenses for extended sources with algorithmic differentiable ray tracing and truncated hierarchical B-splines.

We propose a method for optimizing the geometry of a freeform lens to redirect the light emitted from an extended source into a desired irradiance distribution. We utilize a gradient-based optimization approach with MITSUBA 3, an algorithmic differentiable non-sequential ray tracer that allows us to obtain the gradients of the freeform surface parameters with respect to the produced irradiance distribution. To prevent the optimizer from getting trapped in local minima, we gradually increase the number of degrees of freedom of the surface by using Truncated Hierarchical B-splines (THB-splines) during optimization. The refinement locations are determined by analyzing the gradients of the surface vertices. We first design a freeform using a collimated beam (zero-etendue source) for a complex target distribution to demonstrate the method's effectiveness. Then, we demonstrate the ability of this approach to create a freeform that can project the light of an extended Lambertian source into a prescribed target distribution.