Parallel Imaging Acceleration Factors Research Articles

Multiband accelerated 2D EPI for multi-echo brain QSM at 3 T.

Data for QSM are typically acquired using multi-echo 3D gradient echo (GRE), but EPI can be used to accelerate QSM and provide shorter acquisition times. So far, EPI-QSM has been limited to single-echo acquisitions, which, for 3D GRE, are known to be less accurate than multi-echo sequences. Therefore, we compared single-echo and multi-echo EPI-QSM reconstructions across a range of parallel imaging and multiband acceleration factors. Using 2D single-shot EPI in the brain, we compared QSM from single-echo and multi-echo acquisitions across combined parallel-imaging and multiband acceleration factors ranging from 2 to 16, with volume pulse TRs from 21.7 to 3.2 s, respectively. For single-echo versus multi-echo reconstructions, we investigated the effect of acceleration factors on regional susceptibility values, temporal noise, and image quality. We introduce a novel masking method based on thresholding the magnitude of the local field gradients to improve brain masking in challenging regions. At 1.6-mm isotropic resolution, high-quality QSM was achieved using multi-echo 2D EPI with a combined acceleration factor of 16 and a TR of 3.2 s, which enables functional applications. With these high acceleration factors, single-echo reconstructions are inaccurate and artefacted, rendering them unusable. Multi-echo acquisitions greatly improve QSM quality, particularly at higher acceleration factors, provide more consistent regional susceptibility values across acceleration factors, and decrease temporal noise compared with single-echo QSM reconstructions. Multi-echo acquisition is more robust for EPI-QSM across parallel imaging and multiband acceleration factors than single-echo acquisition. Multi-echo EPI can be used for highly accelerated acquisition while preserving QSM accuracy and quality relative to gold-standard 3D-GRE QSM.

10-channel phased-array coil for carotid wall MRI at 3T.

Accurate assessment of plaque accumulation near the carotid bifurcation is important for the effective prevention and treatment of stroke. However, vessel and plaque delineation using MRI can be limited by low contrast-to-noise ratio (CNR) and long acquisition times. In this work, a 10-channel phased-array receive coil design for bilateral imaging of the carotid bifurcation using 3T MRI is proposed. The proposed 10-channel receive coil was compared to a commercial 4-channel receive coil configuration using data acquired from phantoms and healthy volunteers (N = 9). The relative performance of the coils was assessed, by comparing signal-to-noise ratio (SNR), noise correlation, g-factor noise amplification, and the CNR between vessel wall and lumen using black-blood sequences. Patient data were acquired from 12 atherosclerotic carotid artery disease patients. The 10-channel coil consistently provided substantially increased SNR in phantoms (+77 ± 27%) and improved CNR in healthy carotid arteries (+62 ± 11%), or reduced g-factor noise amplification. Patient data showed excellent delineation of atherosclerotic plaque along the length of the carotid bifurcation using the 10-channel coil. The proposed 10-channel coil design allows for improved visualization of the carotid arteries and the carotid bifurcation and increased parallel imaging acceleration factors relative to a commercial 4-channel coil design.

Analysis of physiological noise in quantitative cardiac magnetic resonance.

PurposeTo determine the impact of imaging parameters on the temporal signal-to-noise ratio (TSNR) of quantitative cardiac magnetic resonance (MR) in humans, and to determine applicability of the physiological noise covariance (PNC) model for physiological noise (PN).MethodsWe conducted MRI experiments in four healthy volunteers, and obtained series of short-axis cardiac images acquired with snapshot balanced steady-state free precession (bSSFP) and snapshot gradient echo (GRE) using a broad range of spatial resolutions and parallel imaging acceleration factors commonly used in quantitative cardiac MR. We measured regional SNR and TSNR in these datasets and fit the measurements to the PNC model for PN, which assumes that PN scales with signal strength.ResultsThe relationship between SNR and TSNR in human cardiac MR without contrast preparation was well modeled by the PNC model. SNR consistently decreased as the spatial resolution (matrix size) and acceleration factor (R) increased for both GRE and bSSFP imaging. TSNR varied linearly with SNR using GRE imaging, when SNR was low (SNR < 20), and approached an asymptotic limit using bSSFP imaging, when SNR was high (SNR > 40).ConclusionsThe PNC model can be used to guide the choice of matrix size and acceleration factor to optimize TSNR in stable contrast cardiac MR, such as T2-prepared Blood-Oxygen-Level-Dependent (BOLD) and several variants of Arterial Spin Labeled (ASL) cardiac MR.

Spin echo based cardiac diffusion imaging at 7T: An ex vivo study of the porcine heart at 7T and 3T.

Purpose of this work was to assess feasibility of cardiac diffusion tensor imaging (cDTI) at 7 T in a set of healthy, unfixed, porcine hearts using various parallel imaging acceleration factors and to compare SNR and derived cDTI metrics to a reference measured at 3 T. Magnetic resonance imaging was performed on 7T and 3T whole body systems using a spin echo diffusion encoding sequence with echo planar imaging readout. Five reference (b = 0 s/mm2) images and 30 diffusion directions (b = 700 s/mm2) were acquired at both 7 T and 3 T using a GRAPPA acceleration factor R = 1. Scans at 7 T were repeated using R = 2, R = 3, and R = 4. SNR evaluation was based on 30 reference (b = 0 s/mm2) images of 30 slices of the left ventricle and cardiac DTI metrics were compared within AHA segmentation. The number of hearts scanned at 7 T and 3 T was n = 11. No statistically significant differences were found for evaluated helix angle, secondary eigenvector angle, fractional anisotropy and apparent diffusion coefficient at the different field strengths, given sufficiently high SNR and geometrically undistorted images. R≥3 was needed to reduce susceptibility induced geometric distortions to an acceptable amount. On average SNR in myocardium of the left ventricle was increased from 29±3 to 44±6 in the reference image (b = 0 s/mm2) when switching from 3 T to 7 T. Our study demonstrates that high resolution, ex vivo cDTI is feasible at 7 T using commercial hardware.

Flexible 23-channel coil array for high-resolution magnetic resonance imaging at 3 Tesla.

PurposeThe purpose of this work is the design, implementation and evaluation of a mechanically flexible receive-only coil array for magnetic resonance imaging (MRI) at 3 T that can be applied to various target organs and provides high parallel imaging performance.MethodsA 23-channel array was designed based on a rigid-flex printed circuit board (PCB). The flexible multi-layer part contains the copper traces forming the coil elements. The rigid part of the PCB houses the solder joints and lumped elements. The coil housing consists of rigid caps mounted above the rigid parts. Adhesive PTFE sheets cover all flexible parts. The developed array was tested on the bench as well as in phantom and in vivo MRI experiments employing parallel imaging acceleration factors up to six.ResultsEfficient mutual decoupling between receive elements and detuning between receive array and body coil was achieved. An increased signal-to-noise ratio in comparison to commercial reference coils is demonstrated, especially in regions close to the developed array and for high parallel imaging acceleration factors. Exemplary in vivo images of head, ankle, knee, shoulder and hand are presented.ConclusionBased on high sensitivity close to the array and low g-factors, this flexible coil is well suited for studies of occipital and temporal cortex, as well as musculoskeletal targets like knee, ankle, elbow and wrist.

Evaluation of radiomic texture feature error due to MRI acquisition and reconstruction: A simulation study utilizing ground truth

The purpose of this study was to examine the dependence of image texture features on MR acquisition parameters and reconstruction using a digital MR imaging phantom. MR signal was simulated in a parallel imaging radiofrequency coil setting as well as a single element volume coil setting, with varying levels of acquisition noise, three acceleration factors, and four image reconstruction algorithms. Twenty-six texture features were measured on the simulated images, ground truth images, and clinical brain images. Subtle algorithm-dependent errors were observed on reconstructed phantom images, even in the absence of added noise. Sources of image error include Gibbs ringing at image edge gradients (tissue interfaces) and well-known artifacts due to high acceleration; two of the iterative reconstruction algorithms studied were able to mitigate these image errors. The difference of the texture features from ground truth, and their variance over reconstruction algorithm and parallel imaging acceleration factor, were compared to the clinical “effect size”, i.e., the feature difference between high- and low-grade tumors on T1- and T2-weighted brain MR images of twenty glioma patients. The measured feature error (difference from ground truth) was small for some features, but substantial for others. The feature variance due to reconstruction algorithm and acceleration factor were generally smaller than the clinical effect size. Certain texture features may be preserved by MR imaging, but adequate precautions need to be taken regarding their validity and reliability. We present a general simulation framework for assessing the robustness and accuracy of radiomic textural features under various MR acquisition/reconstruction scenarios.

Reduction of across-run variability of temporal SNR in accelerated EPI time-series data through FLEET-based robust autocalibration

Temporal signal-to-noise ratio (tSNR) is a key metric for assessing the ability to detect brain activation in fMRI data. A recent study has shown substantial variation of tSNR between multiple runs of accelerated EPI acquisitions reconstructed with the GRAPPA method using protocols commonly used for fMRI experiments. Across-run changes in the location of high-tSNR regions could lead to misinterpretation of the observed brain activation patterns, reduced sensitivity of the fMRI studies, and biased results. We compared conventional EPI autocalibration (ACS) methods with the recently-introduced FLEET ACS method, measuring their tSNR variability, as well as spatial overlap and displacement of high-tSNR clusters across runs in datasets acquired from human subjects at 7T and 3T. FLEET ACS reconstructed data had higher tSNR levels, as previously reported, as well as better temporal consistency and larger overlap of the high-tSNR clusters across runs compared with reconstructions using conventional multi-shot (ms) EPI ACS data. tSNR variability across two different runs of the same protocol using ms-EPI ACS data was about two times larger than for the protocol using FLEET ACS for acceleration factors (R) 2 and 3, and one and half times larger for R=4. The level of across-run tSNR consistency for data reconstructed with FLEET ACS was similar to within-run tSNR consistency. The displacement of high-tSNR clusters across two runs (inter-cluster distance) decreased from ∼8mm in the time-series reconstructed using conventional ms-EPI ACS data to ∼4mm for images reconstructed using FLEET ACS. However, the performance gap between conventional ms-EPI ACS and FLEET ACS narrowed with increasing parallel imaging acceleration factor. Overall, the FLEET ACS method provides a simple solution to the problem of varying tSNR across runs, and therefore helps ensure that an assumption of fMRI analysis—that tSNR is largely consistent across runs—is met for accelerated acquisitions.

Three-dimensional black-blood T2 mapping with compressed sensing and data-driven parallel imaging in the carotid artery

PurposeTo develop a 3D black-blood T2 mapping sequence with a combination of compressed sensing (CS) and parallel imaging (PI) for carotid wall imaging. Materials and methodsA 3D black-blood fast-spin-echo (FSE) sequence for T2 mapping with CS and PI was developed and validated. Phantom experiments were performed to assess T2 accuracy using a Eurospin Test Object, with different combination of CS and PI acceleration factors. A 2D multi-echo FSE sequence was used as a reference to evaluate the accuracy. The concordance correlation coefficient and Bland-Altman statistics were calculated. Twelve volunteers were scanned twice to determine the repeatability of the sequence and the intraclass correlation coefficient (ICC) was reported. Wall-lumen sharpness was calculated for different CS and PI combinations. Six patients with carotid stenosis >50% were scanned with optimised sequence. The T2 maps were compared with multi-contrast images. ResultsPhantom scans showed good correlation in T2 measurement between current and reference sequence (r=0.991). No significant difference was found between different combination of CS and PI accelerations (p=0.999). Volunteer scans showed good repeatability of T2 measurement (ICC: 0.93, 95% CI 0.84–0.97). The mean T2 of the healthy wall was 48.0±9.5ms. Overall plaque T2 values from patients were 54.9±12.2ms. Recent intraplaque haemorrhage and fibrous tissue have higher T2 values than the mean plaque T2 values (88.1±6.8ms and 62.7±9.3ms, respectively). ConclusionThis study demonstrates the feasibility of combining CS and PI for accelerating 3D T2 mapping in the carotid artery, with accurate T2 measurements and good repeatability.

Optimizing the acceleration and resolution of three-dimensional fat image navigators for high-resolution motion correction at 7T.

To investigate the effect of spatial resolution and parallel imaging acceleration factor on the quality of the motion estimates derived from image navigators with a three-dimensional (3D) gradient-recalled echo (GRE) acquisition with fat excitation (3D FatNavs) for neuroimaging at 7T. Six healthy subjects were scanned for 10 min, during which time repeated GRE volumes were acquired during small movements-alternating between fat and water excitations (WaterNavs)-allowing retrospective decimation of the data to simulate a variety of combinations of image resolution and acceleration factor. Bias and error in the motion estimates were then compared across navigator parameters. The 2-mm, 4 × 4 accelerated data (TRvolume = 1.2 s) provided motion estimates that were almost indistinguishable from those from the full original acquisition (2 mm, 2 × 2, TRvolume = 5.2 s). For faster navigators, it was found that good accuracy and precision were achievable with TRvolume = 144 ms, using a lower spatial resolution (4 mm, 6 × 6 acceleration) to avoid the bias observed at exceptionally high acceleration factors (8 × 8 or higher). Parameter estimates from WaterNavs and FatNavs showed close agreement with FatNavs, with better performance at exceptionally high acceleration factors. Our data help to guide the parameter choice for 3D FatNavs when a compromise must be reached between the quality of the motion estimates and the available scan time. Magn Reson Med 77:547-558, 2017. © 2016 International Society for Magnetic Resonance in Medicine.

Retrospective correction of involuntary microscopic head movement using highly accelerated fat image navigators (3D FatNavs) at 7T

PurposeThe goal of the present study was to use a three‐dimensional (3D) gradient echo volume in combination with a fat‐selective excitation as a 3D motion navigator (3D FatNav) for retrospective correction of microscopic head motion during high‐resolution 3D structural scans of extended duration. The fat excitation leads to a 3D image that is itself sparse, allowing high parallel imaging acceleration factors – with the additional advantage of a minimal disturbance of the water signal used for the host sequence.MethodsA 3D FatNav was inserted into two structural protocols: an inversion‐prepared gradient echo at 0.33 × 0.33 × 1.00 mm resolution and a turbo spin echo at 600 μm isotropic resolution.ResultsMotion estimation was possible with high precision, allowing retrospective motion correction to yield clear improvements in image quality, especially in the conspicuity of very small blood vessels.ConclusionThe highly accelerated 3D FatNav allowed motion correction with noticeable improvements in image quality, even for head motion which was small compared with the voxel dimensions of the host sequence. Magn Reson Med 75:1030–1039, 2016. © 2015 Wiley Periodicals, Inc.

Retrospective correction of involuntary microscopic head movement using highly accelerated fat image navigators (3D FatNavs) at 7T

The goal of the present study was to use a three-dimensional (3D) gradient echo volume in combination with a fat-selective excitation as a 3D motion navigator (3D FatNav) for retrospective correction of microscopic head motion during high-resolution 3D structural scans of extended duration. The fat excitation leads to a 3D image that is itself sparse, allowing high parallel imaging acceleration factors--with the additional advantage of a minimal disturbance of the water signal used for the host sequence. A 3D FatNav was inserted into two structural protocols: an inversion-prepared gradient echo at 0.33 × 0.33 × 1.00 mm resolution and a turbo spin echo at 600 μm isotropic resolution. Motion estimation was possible with high precision, allowing retrospective motion correction to yield clear improvements in image quality, especially in the conspicuity of very small blood vessels. The highly accelerated 3D FatNav allowed motion correction with noticeable improvements in image quality, even for head motion which was small compared with the voxel dimensions of the host sequence.

Two-dimensional accelerated MP-RAGE imaging with flexible linear reordering

Implementation of an accelerated Magnetization Prepared RApid Gradient Echo (MP-RAGE) sequence for T1 weighted neuroimaging; exploiting modern MRI technologies to minimize scan time while preserving the image quality. A custom MP-RAGE sequence was implemented on a state-of-the-art 3T MR scanner equipped with a 32-channel receiver array head coil. The sequence utilized a shifted CAIPIRINHA k y -k z under-sampling pattern combined with elliptical scanning and a two-dimensional view ordering scheme to achieve high parallel imaging acceleration factors at maintained image contrast. It could be shown that MP-RAGE accelerated in two k-space directions outperforms single direction acceleration, which is the common practice with standard view ordering. Applying the CAIPIRINHA technique in conjunction with elliptical scanning further increased this benefit. By combining MP-RAGE with CAIPIRINHA sampling and elliptical scanning, the scan time can be reduced from 4-5 min to 2-3min with insignificant reduction in image quality.

Group-level impacts of within- and between-subject hemodynamic variability in fMRI

Inter-subject fMRI analyses have specific issues regarding the reliability of the results concerning both the detection of brain activation patterns and the estimation of the underlying dynamics. Among these issues lies the variability of the hemodynamic response function (HRF), that is usually accounted for using functional basis sets in the general linear model context. Here, we use the joint detection-estimation approach (JDE) (Makni et al., 2008; Vincent et al., 2010) which combines regional nonparametric HRF inference with spatially adaptive regularization of activation clusters to avoid global smoothing of fMRI images. We show that the JDE-based inference brings a significant improvement in statistical sensitivity for detecting evoked activity in parietal regions. In contrast, the canonical HRF associated with spatially adaptive regularization is more sensitive in other regions, such as motor cortex. This different regional behavior is shown to reflect a larger discrepancy of HRF with the canonical model. By varying parallel imaging acceleration factor, SNR-specific region-based hemodynamic parameters (activation delay and duration) were extracted from the JDE inference. Complementary analyses highlighted their significant departure from the canonical parameters and the strongest between-subject variability that occurs in the parietal region, irrespective of the SNR value. Finally, statistical evidence that the fluctuation of the HRF shape is responsible for the significant change in activation detection performance is demonstrated using paired t-tests between hemodynamic parameters inferred by GLM and JDE.

High acceleration quiescent-interval single shot magnetic resonance angiography at 3T in patients with peripheral artery disease

Background Quiescent-Interval Single Shot (QISS) non-contrast MR angiography (QISS-MRA) is an emerging technique with growing evidence for its use in the evaluation of peripheral artery disease (PAD) at 1.5T [1,2]. The use of 3 Tesla MRI scans is becoming more common in clinical practice and offers the main advantage of roughly double the signal-to-noise ratio (SNR) than that of 1.5 Tesla MRI. Improvements in B1 field inhomogeneity along with fast (parallel) imaging make QISS-MRA a viable technique on state-of-the-art 3T scanners. A prior study from this group investigated the potential to accelerate imaging at 3T using higher parallel imaging acceleration (PAT) factors on healthy volunteers [3]. With this technique optimized, we report preliminary results in clinical patients. The objective of this study is to evaluate the diagnostic quality of QISS at 3T in patients with PAD using contrast-enhanced MR angiography (CE-MRA) as the reference standard. Methods With IRB approval, eight patients (5 males, age 58-78 yrs; 3 females age 37-82) with symptoms of chronic lower extremity PAD were recruited prospectively and underwent imaging on a 3T scanner (MAGNETOM Skyra; Siemens Healthcare, Germany) using an ECG-gated QISSMRA sequence (PAT factor of 3); CE-MRA was acquired at 3T for each patient at the time of visit. The degree of stenosis was evaluated using a 5-point scale for 31 predefined arterial segments (from infra-renal aorta through to bilateral run-off vessels) on both QISS- and CE-MRA. The sensitivity and specificity of QISS-MRA at 3T for the determination of clinically significant (≥50%) versus nonsignificant (<50%) stenosis were calculated with CE-MRA as the reference standard; time-resolved acquisitions were included in the analysis.

Echo Planar Diffusion-Weighted Imaging: Possibilities and Considerations with 12- and 32-Channel Head Coils

Interest in clinical brain magnetic resonance imaging using 32-channel head coils for signal reception continues to increase. The present investigation assesses possibilities for improving diffusion-weighted image quality using a 32-channel in comparison to a conventional 12-channel coil. The utility of single-shot (ss) and an approach to readout-segmented (rs) echo planar imaging (EPI) are examined using both head coils. Substantial image quality improvements are found with rs-EPI. Imaging with a 32-channel head coil allows for implementation of greater parallel imaging acceleration factors or acquisition of scans at a higher resolution. Specifically, higher resolution imaging with rs-EPI can be achieved by increasing the number of readout segments without increasing echo-spacing or echo time to the degree necessary with ss-EPI — a factor resulting in increased susceptibility artifact and reduced signal-to-noise with the latter.

Artificial Luminal Narrowing on Contrast-Enhanced Magnetic Resonance Angiograms on an Occasion of Stent-Assisted Coiling of Intracranial Aneurysm:In VitroComparison Using Two Different Stents with Variable Imaging Parameters

ObjectiveIntracranial stenting for stent-assisted coiling of aneurysms requires adequate follow-up imaging. The aim of this in vitro study was to compare in-stent artificial luminal narrowing on contrast-enhanced MR angiograms (CE-MRA) when applying Neuroform® and Enterprise® stents for stent-assisted coiling.Materials and MethodsTwo intracranial nitinol stents (Enterprise® and Neuroform®) were placed in silicon tubes and then imaged at 3 T and 1.5 T by the use of a T1-weighted three-dimensional spoiled gradient-echo sequence with minimal TR and TE. CE-MRAs were obtained by using different imaging planes, voxel sizes, and bandwidths, and with or without parallel imaging. Artificial lumen narrowing (ALN) was calculated and the results were compared.ResultsLower magnetic field strength, axial plane perpendicular to axis of stent, and wider bandwidth resulted in a lower ALN on CE-MRA for both stents. Larger voxel size resulted in lower ALN for Neuroform® stent. The parallel imaging acceleration factor did not affect ALN. The mean ALN was lower for Neuroform®, but it was not significant by a paired t test.ConclusionCE-MRA of the stented lumen of vascular phantom was partially impaired with ALN. Consequently, image plane orientation, magnetic field strength, bandwidth, and voxel size should be adjusted appropriately to reduce ALN.

A Transmit/Receive Radiofrequency Array for Imaging the Carotid Arteries at 7 Tesla

To develop a transmit/receive radiofrequency (RF) array for magnetic resonance imaging (MRI) of the carotid arteries at 7 T. The prototype is characterized in numerical simulations and bench measurements, and the feasibility of plaque imaging at 7 T is demonstrated in first in vivo images. The RF phased array coil consists of 8 surface loop coils. To allow imaging of both sides of the neck, the RF array is divided into 2 coil clusters, each with 4 overlapping loop elements. For safety validation, numerical computations of the RF field distribution and the corresponding specific absorption rate were performed on the basis of a heterogeneous human body model. To validate the coil model, maps of the transmit B1(+) field were compared between simulation and measurement. In vivo images of a healthy volunteer and a patient (ulcerating plaque and a 50% stenosis of the right internal carotid artery) were acquired using a 3-dimensional FLASH sequence with a high isotropic spatial resolution of 0.54 mm as well as using pulse-triggered proton density (PD)/T2-weighted turbo spin echo sequences. Measurements of the S-parameters yielded a reflection and isolation of the coil elements of better than -18 and -13 dB, respectively. Measurements of the g-factor indicated good image quality for parallel imaging acceleration factors up to 2.4. A similar distribution and a very good match of the absolute values were found between the measured and simulated B1(+) transmit RF field for the validation of the coil model. In vivo images revealed good signal excitation of both sides of the neck and a high vessel-to-background image contrast for the noncontrast-enhanced 3-dimensional FLASH sequence. Imaging at 7 T could depict the extent of stenosis, and revealed the disruption and ulcer of the plaque. This study demonstrates that 2 four-channel transmit/receive RF arrays for each side of the neck is a suitable concept for in vivo MRI of the carotid arteries at 7 Tesla. Further studies are needed to explore and exploit the full potential of 7 T high-field MRI for carotid atherosclerotic plaque imaging.

Improvements in parallel imaging accelerated functional MRI using multiecho echo-planar imaging

Multiecho echo-planar imaging (EPI) was implemented for blood-oxygenation-level-dependent functional MRI at 1.5 T and compared to single-echo EPI with and without parallel imaging acceleration. A time-normalized breath-hold task using a block design functional MRI protocol was carried out in combination with up to four echo trains per excitation and parallel imaging acceleration factors R = 1-3. Experiments were conducted in five human subjects, each scanned in three sessions. Across all reduction factors, both signal-to-fluctuation-noise ratio and the total number of activated voxels were significantly lower using a single-echo EPI pulse sequence compared with the multiecho approach. Signal-to-fluctuation-noise ratio and total number of activated voxels were also considerably reduced for nonaccelerated conventional single-echo EPI when compared to three-echo measurements with R = 2. Parallel imaging accelerated multiecho EPI reduced geometric distortions and signal dropout, while it increased blood-oxygenation-level-dependent signal sensitivity all over the brain, particularly in regions with short underlying T*(2). Thus, the presented method showed multiple advantages over conventional single-echo EPI for standard blood-oxygenation-level-dependent functional MRI experiments.

An Eight-Channel Phased Array RF Coil for Spine MR Imaging at 7 T

To develop a transmit/receive radiofrequency (RF) array for MR imaging of the human spine at 7 T. The prototype is characterized in simulations and bench measurements, and the feasibility of high-resolution spinal cord imaging at 7 T is demonstrated in in vivo images of volunteers. The RF phased array consists of 8 overlapping surface loop coils with a dimension of 12 cm x 12 cm each. Bench measurements were obtained with a phantom made of body-simulating liquid and assessed with a network analyzer. For safety validation, numerical computations of the RF field distribution and the corresponding specific absorption rate were performed on the basis of 3 different human body models. In vivo images of 3 volunteers (2 with a documented scoliosis) were acquired using a 3D-FLASH sequence with a high spatial resolution of 0.57 mm isotropic. The 7 T transmit/receive RF coil could be easily integrated into the patient table for examinations of the cervicothoracic or thoracolumbosacral spine. Comparable results were found for all 3 numerical calculations using different human body models. Measurements of the g-factor indicated good image quality for parallel imaging acceleration factors up to 2.7 along the head-feet direction, which could be validated in the in vivo images. The in vivo images demonstrated very fine anatomic features such as the longitudinal ligaments or the venous drainage through the vertebral bodies. A largely homogeneous excitation over an extensive field-of-view of 40 cm could be obtained. These early results indicate that a multichannel transmit/receive phased array RF coil can be used for in vivo spine imaging at 7 T, thereby rendering high-resolution spine imaging a promising new application in 7 T clinical research.

Parallel imaging: is GRAPPA a useful acquisition tool for MR imaging intended for volumetric brain analysis?

BackgroundThe work presented here investigates parallel imaging applied to T1-weighted high resolution imaging for use in longitudinal volumetric clinical studies involving Alzheimer's disease (AD) and Mild Cognitive Impairment (MCI) patients. This was in an effort to shorten acquisition times to minimise the risk of motion artefacts caused by patient discomfort and disorientation. The principle question is, "Can parallel imaging be used to acquire images at 1.5 T of sufficient quality to allow volumetric analysis of patient brains?"MethodsOptimisation studies were performed on a young healthy volunteer and the selected protocol (including the use of two different parallel imaging acceleration factors) was then tested on a cohort of 15 elderly volunteers including MCI and AD patients. In addition to automatic brain segmentation, hippocampus volumes were manually outlined and measured in all patients. The 15 patients were scanned on a second occasion approximately one week later using the same protocol and evaluated in the same manner to test repeatability of measurement using images acquired with the GRAPPA parallel imaging technique applied to the MPRAGE sequence.ResultsIntraclass correlation tests show that almost perfect agreement between repeated measurements of both segmented brain parenchyma fraction and regional measurement of hippocampi. The protocol is suitable for both global and regional volumetric measurement dementia patients.ConclusionIn summary, these results indicate that parallel imaging can be used without detrimental effect to brain tissue segmentation and volumetric measurement and should be considered for both clinical and research studies where longitudinal measurements of brain tissue volumes are of interest.