Oxide Dispersion Strengthened Research Articles

Microstructures and properties of Al2O3 dispersion-strengthened Cu10Sn oil bearings prepared by solid-liquid doping and reactive synthesis method

To modify the shortcomings of Cu10Sn oil bearing in mechanical performance, this work proposes to prepare the Al2O3 oxide dispersion strengthened (ODS) Cu10Sn oil bearings by reactive synthesis using elemental Sn and Al2O3 ODS-Cu powder, among which the uniformly doped Al2O3 ODS-Cu powder was synthesized through a solid-liquid doping of Al(NO3)3 in CuO powders followed with hydrogen reduction. The effects of Al2O3 content on the microstructure and properties of ODS-Cu powder and ODS-Cu10Sn oil bearings were investigated in details. The results showed that an increase in Al2O3 amount from 0 to 1.5wt.% leads to a decrease in the average particle size of the reduced ODS-Cu powders, and contributes to the significant improvement of radial compressive strength, and Vickers microhardness. The appropriate sintering temperature is approximately 800 °C, which can result in the evenly distributed Al2O3 and well-developed porosity in oil bearing sample after sintering. The corresponding compressive strength and microhardness of ODS1.5-Cu10Sn oil bearing can reach 305MPa and 208 HV respectively.

New dispersion mechanism for oxide dispersion-strengthened steels by liquid metallurgy

The use of oxide dispersion-strengthened (ODS) alloys in demanding applications can effectively reduce parts’ weights, extend life of use, and enhance overall energy efficiency. But, the current manufacturing of ODS alloys has remained impractical for decades due to poor scalability and extremely high costs. Mass production of ODS steels by liquid metallurgy is therefore crucial to decrease their costs by several orders of magnitude and expand their potential applications. However, oxide nanoparticle (NP) dispersion in molten alloys presents fundamental challenges for liquid metallurgy due to the vastly dissimilar atomic properties between ionocovalent oxides and metals. Here we show, for the first time, that Y2O3 NPs are able to be dispersed in liquid 316L with a 1 % Nb addition. It was discovered that Nb-enriched interfacial layers exist around the Y2O3 NPs in solidified steels after slow cooling. Theoretical analyses reveal that the Nb-enriched interfacial layer induces a higher energy barrier and a significantly lower van der Waals attraction between oxide NPs and liquid Fe for the successful dispersion of oxide NPs in liquid steels. Moreover, Y2O3 and Al2O3 NPs were successfully dispersed in lean steels, such as Fe-Nb and low-C steels. This new dispersion mechanism of oxide NPs opens an exciting pathway for the economical mass manufacturing of various ODS alloys by liquid metallurgy for numerous applications.

Study of helium diffusion in yttria: A multiscale approach based on the density functional theory and kinetic Monte Carlo, with transmission electron microscopy and thermo-desorption spectroscopy

A known issue for future nuclear reactors is helium accumulation inside the steel structure materials, responsible for structural issues such as embrittlement and cracking. One possible solution is using new types of reinforced steel, such as oxide dispersion strengthened (ODS) steel. It consists of adding oxide nanoparticles to the Fe-based material, especially yttrium oxide (yttria, Y2O3), improving its properties. Therefore, one first step is understanding the helium diffusion inside this system. Very little is known about helium inside yttria, with most studies being theoretical ones. Based on this context, this work proposes a combined theoretical and experimental multiscale approach to investigate helium diffusion inside yttria.The theoretical approach starts with the density functional theory, used to model the atomic yttria cell and determine helium insertion sites. The transitions between the sites were described using the Nudged Elastic Bond (NEB) method. Kinetic Monte Carlo was then employed to obtain the interstitial diffusion coefficient expression for the first time for this material. It showed a limited diffusion at temperatures below 600 K, which may indicate a tendency for He to be blocked in the oxide. Then, the charged vacancies were explored. It showed that the vacancy further reduces helium diffusion. Finally, it was demonstrated that helium spreads across different vacancies and interstitial sites.The experimental part involved implanting helium ions at 50 keV in samples with nanometric or micrometric grains. Then, the specimens were characterised with transmission electron microscopy (TEM) and thermo-desorption spectroscopy (TDS) techniques. TEM did not evidence detectable bubbles even at the highest studied fluence (1 × 1016 cm−2). The TDS highlighted different mechanisms for helium diffusion and the grain size's role, providing a novel model for diffusion coefficient calculation based on interstitial diffusion.

Microstructure and properties of oxide-reinforced FeCrAl matrix alloy manufactured by selective laser melting

In this work, nano-Y2O3 dispersed FeCrAl powders (NYD-Fe) were used to produce oxide dispersion strengthened (ODS) alloy by selective laser melting (SLM), and their microstructures and properties were investigated in detail by the kinds of characterization techniques. The results indicate that the Y2O3 particles adhered to the surface of FeCrAl powder absorb more laser, thus increasing the laser energy demand. High quality ODS deposits can be obtained at 600 mm/s and 180 W parameters. The ODS samples deposited by SLM exhibit coarse columnar grains with [001] texture. The Ti-rich nanoparticles and core-shell structured nanoparticles (Y- and O-rich core surrounded by a Ti-rich shell) are observed in ODS alloys. The precipitation formation of core-shell structured nanoparticles involves ball milling amorphization and dissolution reprecipitation. The ODS-180 alloy exhibits a higher ductility compared to FeCrAl-180 alloy, which is caused by the cellular structure with high density dislocations and the nano-sized precipitates inhibit the dislocation motion. The wear rate of the ODS-180 alloy is 51% lower than that of FeCrAl-180 alloy, which is mainly ascribed to the hardness and interface oxide layer resulting from its specific microstructural features.

Laser powder bed fusion of oxide dispersion-strengthened IN718 alloys: A complementary study on microstructure and mechanical properties

In this study, two new grades of oxide dispersion strengthened (ODS) Inconel 718 (IN718) alloys were designed by the thermochemical CALPHAD method and produced by laser powder bed fusion (LPBF) technique. Alloys designated as IN718-YF and IN718-YFH, that consist Y2O3 – FeO and Y2O3 - FeO - Hf, respectively, were fabricated with >99.9% densification using optimized process parameters. CALPHAD calculations were highly consistent with experimental findings, highlighting the formation of Al-containing Y-Ti-O and Y-Hf-O nano-oxides in both alloy types. Texture analyzes revealed no significant texture development in as-built (AB) or heat-treated (HT) alloys. Heat treatment was applied at 1050 °C for 1h to enhance nano-oxide density. The nano-oxide number density remained similar in IN718-YF while it decreased in IN718-YFH alloy as a result of carbide formation after the heat treatment. Besides, formation of secondary γ' particles was observed in the IN718-YFH / HT alloy. Even though the yield strengths of IN718-YF and IN718-YFH alloys in both AB and HT conditions were similar, the ductility of IN718-YFH was ∼50% less in almost all conditions compared to the ductility of IN718-YF. This has been shown to be as a result of irregular shaped micron-sized Y-Hf-O oxides, martensite formation in AB condition, increased amount of carbides and existence of secondary γ' particles in HT condition in IN718-YFH. High density of stacking faults (SF) forming at the interface of the nano-oxides have been detected in IN718-YF alloys. Besides dislocation/nanoparticle interactions, SFs which are responsible for the delocalization of the deformation improve the ductility of IN718-YF alloys. Overall, high temperature mechanical tests exhibit that both alloys have higher strength with improved ductility compared to the standard IN718 alloys, indicating the contribution of the nano-oxides.

Characteristics of oxide-dispersion strengthened alloys produced by high-temperature severe deformation

This study is to explore an economically attractive and technically feasible processing method for oxide-nanoparticle strengthened alloys for fusion reactor application. Despite many scientific merits of the advanced oxide-dispersion strengthened (ODS) alloys, such as the nanostructured ferritic alloy (NFA) 14YWT, the only viable production path for a high-quality NFA is the high-power mechanical alloying process. This process is often a multi-day high-speed ball milling of alloy powder with a small quantity of yttria (Y2O3) powder, followed by the milled-powder consolidation using extrusion or other methods and additional thermomechanical processing (TMP) for property control. This complex production path, including the low-temperature mechanical alloying in particular, has limited technical advancement toward the cost-effective and scale-up production of ODS alloy components. To overcome such a practical limitation, we proposed to explore alternative low-cost processing routes using traditional thermomechanical processing (TMP) method only. A series of continuous TMP cycles, which were designed to impose high-temperature severe plastic deformation (HT-SPD) conditions to the consolidated powder mixtures, were applied to achieve the effective distribution of oxide particles in nanograin structure and thus desirable mechanical properties. Since the reduced-activation ferritic-martensitic (RAFM) alloy powders (Fe-10Cr and Fe-14Cr alloys with various Y contents) are available in our inventory, we focused to utilize the new solid-state synthesis approach for controlling oxide (oxygen source) dissolution and nanoscale clustering in nanograin structure in those alloys. A combination of powder consolidation at 900 °C and continuous thermomechanical activation at 600 °C yielded two essential ODS alloy microstructure contents–nanograin structure and nanoparticle distribution–and thus demonstrated a good combination of strength and ductility.

Superior radiation resistance of ODS-RAFM steels revealed by Positron annihilation spectroscopy study

Oxide-dispersion-strengthened (ODS) reduced-activation ferritic/martensitic (RAFM) steels are considered as most promising structural materials for fusion reactors and other advanced nuclear systems due to its excellent irradiation resistance under high dose irradiations. However, the extreme complex synergistic effect between transmuted helium/hydrogen and displacement damage which most seriously affects the structure and mechanical properties of ODS-RAFM steels is very difficult to understand, especially the role of hydrogen still remains unclear. Taking advantage of very sensitive to small vacancy clusters of Positron annihilation spectroscopy (PAS) method, we conducted irradiation defect study on ODS-RAFM, RAFM and its corresponding model alloy Fe–9Cr and α-Fe to investigate their anti-swelling properties at the early stage of irradiation with hydrogen-helium synergism and the mechanism. Three distinct irradiation schemes including (1) single Fe ion beam, (2) simultaneous Fe and He (named Fe + He) ion beam, (3) subsequent H ion injection after Fe + He (named Fe + He/H) ion beam irradiation were performed. Hydrogen-helium synergistic effects on vacancy evolution within these steels were explored combining the first-principles calculation. The implantation of He was observed to significantly increase defect concentration among all four steels, while H exhibited interestingly complexity on affecting the evolution of helium bubbles. The H post-injection increased defect concentration obviously in the materials with abundant sinks, but improved poorly in ones with rare sinks. Through the systematic study of the interactions between H, He, and vacancies, it was revealed that even at the early irradiation stage, ODS-RAFM steels has already exhibited excellent irradiation resistance compared to other alloys across three irradiation schemes.

Positron annihilation spectroscopy evaluation of using proton irradiation as a surrogate for early neutron radiation damage

A positron annihilation spectroscopy investigation of early stages of radiation-induced damage in Chinese f/m (ferritic/martensitic) steel SIMP and strengthened variant of f/m steel ODS (oxide dispersion strengthened) EUROFER was conducted. Studied materials were irradiated by neutrons at the LVR-15 research reactor to 0.12 dpa at an average temperature of 260 ± 20 °C, and implanted by protons at the 6 MV Tandetron Accelerator of the Slovak University of Technology, to 0.0196 dpa at room temperature (RT) and 300 °C. The potential of using proton irradiation as a surrogate for early neutron radiation damage was investigated. A lifetime spectrometer and Doppler spectrometer was used to obtain simultaneously positron lifetime (PALS) and Doppler broadening spectra (DBS), which provided experimental data used to characterize the vacancy-type defect and their interaction with H atoms in the studied materials. The obtained results show an increase of mean positron lifetime (MLT) in the proton-implanted samples at RT when compared with high temperature irradiation. Similar trend was observed when comparing vacancy concentration of different irradiation conditions. The impact of temperature on mobility and recombination of defects, as well as effect of vacancy stabilization by H atoms, has been addressed. The effect of ODS microstructure on results has been examined. A methodology of comparing various irradiation conditions has been proposed, where the vacancy concentrations have been normalized by the dpa values. The potential application of proton implantation for evaluation of early stages of neutron damage was found to be promising.

Oxidation Behavior of Ni-Based Oxide Dispersion-Strengthened Alloy Fabricated by Direct Energy Deposition at 1100 °C

Oxidation Behavior of Ni-Based Oxide Dispersion-Strengthened Alloy Fabricated by Direct Energy Deposition at 1100 °C

Effect of Nitrogen Atmosphere Annealing of Alloyed Powders on the Microstructure and Properties of ODS Ferritic Steels.

Oxide Dispersion Strengthened (ODS) ferritic steels are promising materials for the nuclear power sector. This paper presents the results of a study on the sintering process using the Spark Plasma Sintering (SPS) technique, focusing on ODS ferritic steel powders with different contents (0.3 and 0.6 vol.%) of Y2O3. The novelty lies in the analysis of the effect of pre-annealing treatment on powders previously prepared by mechanical alloying on the microstructure, mechanical, and thermal properties of the sinters. Using the SPS method, it was possible to obtain well-densified sinters with a relative density above 98%. Pre-annealing the powders resulted in an increase in the relative density of the sinters and a slight increase in their thermal conductivity. The use of low electron energies during SEM analysis allowed for a fairly good visualization of the reinforcing oxides uniformly dispersed in the matrix. Analysis of the Mössbauer spectroscopy results revealed that pre-annealing induces local atomic rearrangements within the solid solution. In addition, there was an additional spectral component, indicating the formation of a Cr-based paramagnetic phase. The ODS material with a higher Y2O3 content showed increased Vickers hardness values, as well as increased Young's modulus and nanohardness, as determined by nanoindentation tests.

Manufacturing Oxide Dispersion Strengthened (ODS) steel plate via cold spray and friction stir processing

Oxide dispersion strengthened (ODS) steels, traditionally fabricated by ball milling and conventional powder metallurgy techniques to achieve bulk form, followed by intricate rolling and thermal treatment steps to achieve plate or sheet form. Here, we present a novel processing route that combines cold spray (CS) with friction stir processing (FSP) to manufacture ODS steel plate directly from gas atomization reaction synthesis (GARS)-prepared powder, thus no rolling steps involved. Microstructural and mechanical characterizations were performed to assess the quality and properties of the resulting ODS steel plate. Our findings demonstrate that the slightly porous CS deposited layer was fully consolidated after FSP, yielding a fully dense ODS steel plate that exhibited a favorable tradeoff between strength and ductility upon extraction from the substrate. Furthermore, through microstructural analysis, we revealed the presence of an appreciable density (∼1022/m3) of nano-sized oxide particles, with the majority being smaller than 5 nm via the combined CS + FSP fabrication route. This work serves as a first proof-of-concept demonstration of the manufacturing approach described herein, offering a possible alternative route for producing ODS steel plates.

Ultrahigh-strengthened intragranular κ-Al2O3 nanoparticles dispersed Mo composite prepared via SPS sintering of core-shell Mo nanocomposite powder

Oxide dispersion strengthening (ODS) is an effective method to improve the mechanical properties of Mo-based materials. However, the mechanical properties of traditional ODS-Mo composites are always limited by the coarsening and intergranular distribution of second-phase particles. In this work, an effective nano-reinforcement dispersion strategy was developed to fabricate an ODS-Mo composite with ultrafine grain and intragranular distribution of second-phase particles. Core-shell structural Mo nanocomposite powders, with internally distributed sub-10 nm Al2O3 dispersoids, were prepared by nano atomization doping (AD) followed by a chemical vapor transport growth strategy. Then, ODS-Mo composites with ultra-fine Mo grain (below 700 nm) and high-density intragranular κ-Al2O3 (below 20 nm) nanoparticles were prepared via spark plasma sintering (SPS), in which a coherent interface between κ-Al2O3 and Mo matrix was formed. The composites present remarkably improved hardness (above 500 HV), bend strength, and compressive yield strength (above 1664 MPa) at room temperature, with a suitable strain to fracture of 27.1 %. The calculation of strengthening mechanisms indicates that the enhancement was mainly attributed to the intragranular κ-Al2O3 nanoparticles. This nano-sized reinforcement distributed within the grain can more effectively pin dislocations and achieve dispersion strengthening in ODS-Mo composites. Therefore, this strategy can efficiently construct intragranular second-phase nanoparticles and open up new avenues to fabricate high-performance ODS-Mo composites.

Hot compression bonding of a 9Cr oxide dispersion strengthened alloy and a 9Cr reduced-activation ferritic/martensitic alloy

An innovative method of hot compression bonding is proposed in this work for the joining of 9Cr oxide dispersion strengthened (ODS) alloy and 9Cr reduced-activation ferritic/martensitic (RAFM) alloy. The microstructural evolution of the bonding interface was investigated by scanning electron microscopy (SEM), electron back-scattered diffraction (EBSD), and transmission electron microscopy (TEM). The results verify that the pinning effect of nano-oxides particles (NPs) in 9Cr ODS alloy significantly enhances its dynamic recrystallization (DRX) temperature and deformation resistance. Continuous DRX (CDRX) first occurred on the 9Cr RAFM alloy side, and the areas near the bonding interface were composed of recrystallized grains. With increasing strain, CDRX also showed up on the 9Cr ODS alloy side. Inevitable slight oxidation occurred at the bonding interface during the hot compression bonding (HCB) process, and the interfacial oxides transformed from initial coarse CrO to TiO and finally to Y-Ti-O nanoparticles with sizes comparable to pre-existing NPs dispersed in the 9Cr ODS alloy matrix. It is believed that interfacial oxide transformation and grain structure consistency contributed to the excellent interface healing of the two dissimilar alloy pieces. The effectiveness of the bonding was tested by tensile tests and fractography analysis, revealing that ideal metallurgical bonding could be achieved under a controlled strain level of 10 % at 800 °C followed by soaking at 1000 °C for 4 h.

Processing heterogeneously structured oxide-dispersion-strengthened Fe-10Cr-6.1Al-0.3Zr-0.1Y alloy for simultaneously enhanced strength and ductility

An oxide-dispersion-strengthened (ODS) Fe-10Cr-6.1Al-0.3Zr-0.1Y alloy with a bimodal grain size distribution was developed via a simple process of internal oxidation and powder forging. The intentionally promoted heterogeneous microstructure consists of coarse-grained “core” regions enclosed by mutually connected fine-grained “shell” zones, facilitated by unevenly distributed oxide particles. The sample sintered and then forged at 1150 ℃ exhibited a yield strength of 598 MPa, a tensile strength of 734 MPa, and a fracture elongation of 25.1%. Such simultaneously enhanced strength and ductility are significantly above those of cast or previous powder-consolidated counterparts. During tensile deformation, a strain gradient is built up across the inhomogeneous grains and a high density of geometrically necessary dislocations was observed near the interfaces of matrix/oxide particles, both contributing to heterogeneous deformation-induced strengthening. This elevates the work hardening rate and consequently the tensile elongation. Quantitative analysis indicates that the dislocation build-up during forging makes the dominant contribution to the high yield strength of Ox-1150. The present study offers a new route to the preparation of heterogeneously structured ODS Fe-Cr-Al alloys and provides guidance for optimizing the mechanical properties of such alloys in terms of strength-ductility synergy.

Microstructure and mechanical properties of oxide dispersion strengthened FeNiMnCr high-entropy alloy fabricated by spark plasma sintering

High-entropy alloys (HEAs) strengthened by dispersed oxide nanoparticles are considered potential structural materials used in advanced nuclear reactors. Herein, a novel Y-Si-O nanoparticle-strengthened near-equiatomic FeNiMnCr HEA was prepared via the powder metallurgy method. Microstructural characterizations revealed that the oxide dispersion-strengthened (ODS) FeNiMnCr HEA consisted of the face-centered cubic (FCC) matrix and high-density Y-Si-O nanoparticles (Y2SiO5 and Y2Si2O7). The average diameter and volume fraction of the nanoparticles were counted to be 21.3 nm and 1.02%, respectively. The grain size was reduced from 10.13 μm of the FeNiMnCr HEA to 0.79 μm of the ODS FeNiMnCr HEA. The ODS FeNiMnCr HEA showed a yield strength of 1125 MPa, an ultimate tensile strength of 1137 MPa, and a moderate elongation of 8.3% at room temperature. At 500°C, the ODS FeNiMnCr HEA also had a high yield strength of 662 MPa. Theoretical calculation showed that the high strength of the ODS FeNiMnCr HEA was mainly due to the grain boundary strengthening, dislocation strengthening, and precipitation strengthening.

Atomic Diffusivities of Yttrium, Titanium and Oxygen Calculated by Ab Initio Molecular Dynamics in Molten 316L Oxide-Dispersion-Strengthened Steel Fabricated via Additive Manufacturing.

Oxide-dispersion-strengthened (ODS) steels have long been viewed as a prime solution for harsh environments. However, conventional manufacturing of ODS steels limits the final product geometry, is difficult to scale up to large components, and is expensive due to multiple highly involved, solid-state processing steps required. Additive manufacturing (AM) can directly incorporate dispersion elements (e.g., Y, Ti and O) during component fabrication, thus bypassing the need for an ODS steel supply chain, the scale-up challenges of powder processing routes, the buoyancy challenges associated with casting ODS steels, and the joining issues for net-shape component fabrication. In the AM process, the diffusion of the dispersion elements in the molten steel plays a key role in the precipitation of the oxide particles, thereby influencing the microstructure, thermal stability and high-temperature mechanical properties of the resulting ODS steels. In this work, the atomic diffusivities of Y, Ti, and O in molten 316L stainless steel (SS) as functions of temperature are determined by ab initio molecular dynamics simulations. The latest Vienna Ab initio Simulation Package (VASP) package that incorporates an on-the-fly machine learning force field for accelerated computation is used. At a constant temperature, the time-dependent coordinates of the target atoms in the molten 316L SS were analyzed in the form of mean square displacement in order to obtain diffusivity. The values of the diffusivity at multiple temperatures are then fitted to the Arrhenius form to determine the activation energy and the pre-exponential factor. Given the challenges in experimental measurement of atomic diffusivity at such high temperatures and correspondingly the lack of experimental data, this study provides important physical parameters for future modeling of the oxide precipitation kinetics during AM process.

Liquid metal compatibility of pre-oxidized FeCrAl in flowing Sn

A flowing Sn thermal convection loop (TCL) experiment was conducted in FeCrAlMo (Kanthal alloy APMT) tubing for 1000 h with a peak temperature of 400 °C. Oxide dispersion strengthened (ODS) Fe-(10–12)Cr-6Al and APMT specimens were exposed and all were pre-oxidized to form an external alumina scale. Unlike static exposures at 400° and 500 °C where pre-oxidation prevented dissolution, large mass losses were observed in the TCL hot leg after the specimens were cleaned in Li. The observed pitting suggests that localized failure of the pre-formed alumina surface oxide caused significant metal loss. Specimen mass gains were not observed on the cold leg implying that mass transfer did not occur and the small levels of Fe and Cr in the Sn after the experiment implies that Sn-rich phases may have formed. Post exposure room temperature tensile testing showed limited impact of the Sn exposure on the 12Cr ODS FeCrAl alloy, comparable to a 1000 h anneal in Ar at 400 °C. These results suggest that pre-oxidation is not sufficient to protect FeCrAl alloys in contact with flowing liquid Sn at 350°-400 °C.

Softening mechanism and failure behavior of 9Cr oxide dispersion strengthened steel resistance spot welded joint

Oxide dispersion strengthened (ODS) steel is one of the most promising materials for nuclear applications. However, there are fewer studies on the spot welding of ODS steel, and the softening mechanism of ODS steel resistance spot welded joint is unclear. The microstructural features of the ODS resistance spot welded joint was characterized to analyze the softening mechanism. The failure behavior and tensile shear performance were studied combined with finite element simulation. The results showed that the fusion boundary has the lowest hardness and the softening zone is divided into fusion zone(FZ) softening and heat affected zone(HAZ) softening according to different location in the joint. In FZ softening, the softening is mainly caused by the presence of δ-ferrite and fewer oxides as well as lower dislocation density. In HAZ softening, the softening is mainly caused by larger grains, less oxides. There are two types of failure, the fracture initiated at HAZ softening shows a brittle feature, while initiated at FZ softening shows a ductile feature. The softening leads to a reduction in tensile-shear strength. Thus, the control of softening zone is critical to improve the reliability of welded joints.

Positron annihilation lifetime spectroscopy of FeCr and FeCrAl oxide dispersion strengthened (ODS) alloys

Positron annihilation lifetime spectroscopy (PALS) was performed to characterize the interfacial nanostructure between the oxide particles and ferritic matrix in two types of oxide dispersion strengthened (ODS) alloys: FeCr dispersed with Y-Ti oxide nanoparticles and FeCrAl dispersed with Y-Al oxide nanoparticles. The spectra were precisely fitted and decomposed into three components with two trapping rates. Bulk lifetime approached the theoretical value of 107 ps by taking into account the positron trapping at two types of defects. Structural characterization was performed by coincidence Doppler broadening and high-resolution transmission electron microscopy (HRTEM), revealing that two-trapping defect clusters were closely associated with Y-Ti or Y-Al oxide particles. Trapping was not detected in the non-ODS alloys. Based on Kuramotos advanced theoretical work, the shorter annihilation lifetime (179–194 ps) could be ascribed to positron trapping at vacancies and divacancies localized under the misfit dislocations associated with Y-Ti or Y-Al oxide particles. The longer annihilation lifetime (301–323 ps) could be attributed to Ar-filled gas bubbles precipitated at the oxide particle-matrix interfaces. These results of PALS analyses were consistent with the HRTEM characterization.

Flow behaviors and microstructural evolutions of nickel-based ODS superalloys during hot deformation

The hot deformation behaviors of nickel-based oxide dispersion strengthened (ODS) superalloys fabricated by mechanical alloying (MA) and hot extrusion (HEX) were investigated, the hot compression tests were performed to obtain true stress-true strain curves, the influence of strain rate and temperature connected with the microstructure evolution was analyzed, and the processing map and microstructure proposed at different strain levels was used to select its hot working parameters. The results illustrated that hot working conditions, especially the temperature, strongly influenced the grain structure. Specifically, deforming under high temperatures and low strain rate conditions enhances dynamic softening via dynamic recovery (DRV), dynamic recrystallization (DRX), and grain growth to consume the stored strain energy. In addition, the size and morphology of nanoparticles are not significantly changed before and after deformation, the nanoparticles and the matrix still maintain a good interface combination, and no interfacial mismatch such as nanosvoids between the nanoparticle and matrix is detected due to their outstanding interfacial binding ability and excellent ductility of matrix.