Outer Zone Research Articles

Effects of wall confinement on flame topologies and lean blowout characteristics of partially premixed DME/air flames in a gas turbine model combustor

Dimethyl ether (DME) is a promising alternative fuel for gas turbines, considering its renewable nature and potential for large-scale synthesis from CO2 feedstock. However, there are limited studies on the swirl combustion characteristics of DME, particularly regarding the stability performance. This work investigates the effects of wall confinement on flow, mixing, and lean blowout (LBO) characteristics of partially premixed DME/air swirl flames in a gas turbine model combustor. Flow and flame macrostructures are captured using particle image velocimetry and planar laser-induced fluorescence (PLIF) measurements, respectively. The results show remarkable differences in flame topologies between unconfined and confined flames, especially the formation of inner recirculation zone and outer recirculation zone. The LBO limits are measured over various Reynolds numbers and flame dynamics approaching LBO are captured using 10 kHz OH* chemiluminescence imaging. Unconfined flames have unexpectively lower LBO limits (∼0.4) than the LBO limits of confined flames (over 0.5). Approaching LBO, unconfined flames display a quiet blowout mode featuring swirling spiral blow-off behaviors. In contrast, confined flames exhibit a violent blowout mode featuring large-scale quasi-instability behaviors, including periodic events of local extinction, flame lift-off, and re-ignition. Based on the numerical simulations and simultaneous OH- and CH2O-PLIF measurements, the large discrepancy in the measured LBO limits between the two configurations is found to result from different re-ignition processes related to the low-temperature ignition before the final blowout. These findings highlight the crucial roles of wall confinement in determining the stable flame topologies, LBO characteristics, and mechanisms driving the LBO physics for partially premixed DME/air swirl flames.

Winter Wheat Aboveground-Biomass Estimation and Its Dynamic Variation during Coal Mining—Assessing by Unmanned Aerial Vehicle-Based Remote Sensing

Underground coal mining in coal-grain overlapped areas leads to land subsidence and deformation above the goaf, damaging cultivated land. Understanding the influencing process of coal mining on cultivated land and crops is important for carrying out timely land reclamation and stabilizing crop yield. Research has been carried out by using crop growth parameters to evaluate the damaging degree of cultivated land when the mining subsidence is stable, but few studies focus on the influence of land damage on crop growth when the subsidence is unstable during coal mining. Therefore, this study tracked the three growth stages of winter wheat by using UAV multispectral imagery to explore the dynamic influence of underground mining on winter wheat aboveground biomass (AGB). Firstly, a winter-wheat-AGB estimation model (R2 = 0.89, RMSE = 2.18 t/ha) was developed by using vegetation indexes (VIs), textures, and terrain data extracted from UAV imagery. Secondly, based on the winter-wheat-AGB estimation model, the winter wheat AGB was successfully estimated and mapped at different growth stages. The AGB of winter wheat in the coal mining-affected area was approximately 5.59 t/ha at the reviving stage, 8.2 t/ha at the jointing stage, and 15.6 t/ha at the flowering stage. Finally, combined with the progress of coal mining, the dynamic changing process of crops during underground mining can be inferred by analyzing the spatiotemporal variation in winter wheat AGB. Results showed that, in the dip direction, winter wheat AGB at the flowering stage was the highest at the compression zone, followed by the inner stretch zone, outer stretch zone, and neutral zone. The distance from the waterlogged area and the existence of cracks were found to be the important moderating variables affecting the crop growth status in the mining subsidence area. In the strike direction, there were significant differences in the wheat AGB-affected area as the mining proceeded. Even areas where AGB had previously significantly increased gradually transitioned to significant decreases with the end of mining. The research explores the dynamic changes in winter wheat AGB and land damage status during coal mining. It provides a rapid and non-destructive land-damage-monitoring method to protect cultivated land in mining areas.

On the anisotropic coalescence of elliptic cylindrical voids considering the geometric and distributive properties

The geometric and distributive properties of voids significantly influence anisotropic coalescence behaviour. However, this problem has received little attention owing to the complexity of considering all the properties in the current analytical framework of limit analysis. To address this issue, this study proposes an analytical framework based on an elliptic coordinate system, including the determination of the ligament zone, characterization of plastic flow, and derivation of the void coalescence criterion, for porous materials with various geometric and distributive properties, including size, shape, spacing, and orientation. This framework is motivated by our observations that the evolution of the void geometry and surrounding plastic flow can be well characterized by the grid of the elliptic coordinate system. Subsequently, an analytical function is proposed to determine the ligament zone and coalescence direction with various void properties. A hollow nonaxisymmetric cylindrical unit cell is proposed to describe this ligament zone, and the corresponding trial velocity field is derived by extending the previous Gurson-like velocity field into the elliptic cylindrical coordinate system. The rationality of the field is validated by comparing its equivalent strain rate field with numerical simulations. Finally, a coalescence criterion is derived via the limit analysis of the proposed unit cell undergoing internal necking. Two heuristic adjustments are formulated for the overflow phenomenon in the rigid zone and outer ligament zones. Numerical assessments with various void properties confirm the accuracy of the analytical model. The coalescence criterion can predict the independent and coupling effects of geometric and distributive properties on anisotropic void coalescence. This study provides possible solutions to future plasticity problems of ellipsoidal inclusions.

Evolution of Stellar Rotation in Open Clusters

Understanding stellar rotation and the role of magnetic braking remains a major outstanding problem in astrophysics. In this paper, stellar rotation of the young open cluster Blanco 1 is investigated and compared with other clusters with ages ranging from ∼35 Myr to ∼950 Myr and star masses in the range 0.2 < M⊙ < 1.4. It is proposed that rotation rates of stars in young open clusters are determined by the early angular momentum acquired during formation and not by magnetic braking effects, which operate on longer time scales. On the convective C Sequence, for lighter stars, the early angular velocity is related directly to the moment of inertia. However, for the interface or I Sequence, differential rotation exists and observed rotation rates are essentially the rotation rates of the outer convection zone. It is estimated that the convection zone can rotate at over 10× the rate of the inner radiative zone for heavier stars. This differential rotation process can drive saturated interface dynamos that lead to large rotational mass dependences which can be described by a simple energy transfer model. Comparing with clusters of different ages magnetic braking outlines the evolution of older clusters from young clusters. For old clusters such as Praesepe the majority of stars have experienced spin down, that can be described by a simple model based on an additional momentum loss proportional to the angular momentum of the early cluster, which for the I Sequence is consistent with the well known Skumanich relation.

Performance experiments and pressure drop prediction modelling of an energy-saving cyclone separator

The study proposes a new type of axial-inlet cyclone separator with the smaller cylinder-cone ratio and an expansion tube at the particle exhaust, named energy-saving cyclone separator, which offers several advantages over the traditional tangential inlet cyclone in engineering units. Experimental results demonstrate that the separation efficiency exceeds 83 % for fine particles smaller than 10μm, while the pressure drop is significantly lower than that of the commonly used PV-type tangential inlet cyclone separator, at only 44 % of the PV cyclone separator’s pressure drop. Moreover, the flow fields of energy-saving cyclone separator are measured to analyze its characteristics. It is found that the lower tangential momentum ratio in both the inner and outer swirl zones of energy-saving cyclone separator reduces the dissipation of dynamic swirl pressure at the bottom of the cone section and outlet pipe, resulting in a lower pressure drop. The high proportion of downward axial momentum in the outer swirl section causes the separated large particles to discharge through the dust exhaust, improving the separation efficiency of coarse particles. Furthermore, a model to predict the pressure drop of energy-saving cyclone separator is developed.

Prior Nonmelanoma Skin Cancer is Associated with Fewer Fractures, More Vitamin D Sufficiency, Greater Bone Mineral Density, and Improved Bone Microarchitecture in Older Adults

BackgroundPrior nonmelanoma skin cancer (NMSC), a biomarker of cumulative lifetime sun exposure, is associated with reduced fracture risk later in life. The mechanism is unknown. MethodsProspective cohort analysis of 1099 community-dwelling adults aged 50-80 years with baseline and 10-year follow-up assessments. Histopathologically-confirmed NMSC diagnosis was established by linkage with the Tasmanian Cancer Registry. Bone mineral density (BMD) and vertebral deformity were quantified by DXA, 25-hydroxyvitamin D (25(OH)D) by radioimmunoassay, bone microarchitecture by high-resolution peripheral quantitative CT, melanin density by spectrophotometry, and skin photosensitivity and clinical fracture by questionnaire. 25(OH)D <50 nmol/L was considered deficient. ResultsParticipants with an NMSC reported prior to baseline were less likely to sustain an incident vertebral deformity over 10 years (RR = 0.74, P = .036). There were similar reductions for other fracture types but these did not reach significance. Prior NMSC was associated with baseline (RR = 1.23, P = .005) and 10-year longitudinal (RR = 5.9, P = .014) vitamin D sufficiency and greater total body BMD (β = 0.021g/cm2, P = .034), but not falls risk or muscle strength. The relationship between prior NMSC and bone microarchitecture was age-dependent (pinteraction < 0.05). In the oldest age tertile, prior NMSC was associated with greater volumetric BMD (β = 57.8-62.6, P = .002-0.01) and less porosity (β = −4.6 to −5.2, P = .002-0.009) at cortical, compact cortical and outer transitional zones. ConclusionsPrior NMSC was associated with fewer incident fractures in community-dwelling older adults. This protective association is most likely mediated by modifiable fracture risk factors associated with an outdoor lifestyle, including 25(OH)D, BMD, and bone microarchitecture.

Computational investigation of the effect of the trailing edge thickness on the wind turbine performance

Trailing edge (TE) thickness is a manufacturing constraint in blade design, especially for airfoils with a sharp TE. To achieve a specific TE thickness, blade geometry is often modified during the design process, typically in the outer zone of the blade where the airfoil’s TE is thinner. This area has a significant impact on energy production and loads. Quantifying the effect of TE thickness modifications is crucial for making informed design decisions.Therefore, this study quantifies and compares the impact of linear and polynomial geometry modifications on airfoil aerodynamics and turbine performance. Xfoil and OpenFAST were used to calculate these performance variations in the well-known NREL 5 MW wind turbine. The TE thickness of the model was modified to meet various manufacturing constraints, ranging from no restriction to a limit of 12mm TE thickness.In terms of the aerodynamic behavior of the airfoils, the maximum efficiency of airfoils with low relative thickness decreases as the TE thickness increases. Annual Energy Production shows a reduction of up to 0.42% for the worst case, while blade root loads increase by up to 20%. For low relative thickness airfoils, the linear method has proven to be a better option with less impact on performance.

Finite element modelling of pipe piles driven in low-to-medium density chalk under monotonic axial loading

Percussive driving in low-to-medium density chalk creates a thin annulus of fully de-structured ‘putty’ chalk around pile shafts and an outer annular zone where fracturing is more intense than in the natural chalk. This damage and the related generation, and subsequent equalisation, of excess pore pressures impacts the piles’ time-dependent axial loading behaviour, as do other ageing processes. This paper presents finite element analyses of open steel tubular piles driven for the recent ALPACA and ALPACA Plus research projects under monotonic axial loading to failure after extended ageing periods. A nonlinear elastic stiffness model with a nonlocal deviatoric strain-based Mohr-Coulomb failure criterion was employed, with different sets of properties to represent the de-structured, fractured chalk and intact chalk. It is shown that the piles’ axial responses are mainly controlled by the puttified chalk annuli. A simplified but efficient means is adopted to impose pre-loading chalk effective stress conditions that explicitly capture the effects of installation damage and subsequent ageing. The potential for strain-softening in the brittle chalk is examined and the effective stress paths developed in representative chalk elements throughout the loading are considered in conjunction with the mobilisation of accumulated deviatoric strains. The simulations indicate 264% higher shaft capacity in compression than in tension, which is mainly attributed to the internal chalk plug.

Timing and Evolution of Gold Mineralization in the Maljavr Occurrence (NW Russia), NE Part of the Fennoscandian Shield

Gold occurrence Maljavr is the first Archean conglomerate-hosted gold mineralization found in the Fennoscandian Shield. Gold-mineralized metasomatic rocks form a set of lenses within a 10 m thick linear zone, conformable to the bedding of host conglomerates. The lenses are up to 10 m long and up to 1 m thick and they clearly exhibit three alteration envelopes: the rock in the central part consists of garnet and quartz or garnet-only; biotite, garnet, and quartz make the intermediate biotite–garnet envelope; hornblende, hedenbergite, and quartz are the principal rock-forming minerals in the outer zone of the lenses. All metasomatic rocks contain sulfide mineralization up to 15–20 vol.% and up to 0.6 g/t Au. The main ore mineral is pyrrhotite, and the minor minerals are arsenopyrite, chalcopyrite, pentlandite, löllingite, and troilite. The age of zircon from biotite gneiss in the zone of alteration is 2664 ± 18 Ma, this is considered as the time of formation of lenses of metasomatic rocks. Biotite gneiss-conglomerate and metasomatic rocks were later intruded by tourmaline granite pegmatite 2508 ± 7 Ma. The injection of pegmatite caused re-crystallization of sulfides (mainly arsenopyrite and löllingite) and redistribution of gold. Visible gold in association with Bi minerals native bismuth, ehrigite, maldonite, bismuthinite, joseite-B, and hedleyite was found in inclusions in recrystallized arsenopyrite and löllingite. Au content in the rocks with recrystallized arsenopyrite and löllingite is &gt;1 g/t, up to 30 g/t in hand samples. The 2508 Ma pegmatite is interpreted as synchronous with formation of gold mineralization in its present form. The linkage of gold mineralization with pegmatite and geochemical association Au-As-Se-Te-Bi in the mineralized rocks agree with characteristics of intrusion-related gold deposits worldwide. Biotite gneiss–metaconglomerate, hosting the mineralized altered rocks, was the probable primary source of arsenic and gold for mineralization.

Effect of Zonal Laser Texturing on Friction Reduction of Steel Elements in Lubricated Reciprocating Motion

During co-action between contact elements in reciprocating motion, different working conditions exist in outer and inner zones of stationary elements. Because the tribological effects of surface texturing depend on the operating conditions, various dimple patterns were created in the middle part of the steel disc and near the reversal points. The behaviors of variable dimple patterns were compared with those of uniform texturing and untexturing. It was found that the dimple patterns in the middle disc zone depended on the resistance to motion. The best tribological behavior was obtained for a pit area ratio of 13% and diameter of 0.4 mm in the inner zone, and pit area ratio of 3% and diameter of 0.2 mm in the outer zones. Low resistance to motion and the smallest friction variation of all tested sliding pairs were achieved. For the same pit area ratio of 13% in a disc of 0.4 mm, the dimple diameter behaved better than in the 0.2 mm diameter disc. The greatest decrease in the coefficient of friction of 85% compared to untextured sliding pair was achieved for uniform laser texturing with a pit area ratio of 13% and dimple diameter of 0.4 mm, when the normal load was 40 N and frequency of displacement was 20 Hz.

Revealing the complexity of meniscus microvasculature through 3D visualization and analysis

Three-dimensional information is essential for a proper understanding of the healing potential of the menisci and their overall role in the knee joint. However, to date, the study of meniscal vascularity has relied primarily on two-dimensional imaging techniques. Here we present a method to elucidate the intricate 3D meniscal vascular network, revealing its spatial arrangement, connectivity and density. A polymerizing contrast agent was injected into the femoral artery of human cadaver legs, and the meniscal microvasculature was examined using micro-computed tomography at different levels of detail and resolution. The 3D vascular network was quantitatively assessed in a zone-base analysis using parameters such as diameter, length, tortuosity, and branching patterns. The results of this study revealed distinct vascular patterns within the meniscus, with the highest vascular volume found in the outer perimeniscal zone. Variations in vascular parameters were found between the different circumferential and radial meniscal zones. Moreover, through state-of-the-art 3D visualization using micro-CT, this study highlighted the importance of spatial resolution in accurately characterizing the vascular network. These findings, both from this study and from future research using this technique, improve our understanding of microvascular distribution, which may lead to improved therapeutic strategies.

Phoenixin knockout mice show no impairment in fertility or differences in metabolic response to a high-fat diet, but exhibit behavioral differences in an open field test.

Phoenixin (PNX) is a conserved secreted peptide that was identified 10 years ago with numerous studies published on its pleiotropic functions. PNX is associated with estrous cycle length, protection from a high-fat diet, and reduction of anxiety behavior. However, no study had yet evaluated the impact of deleting PNX in the whole animal. We sought to evaluate a mouse model lacking the PNX parent gene, small integral membrane protein 20 (Smim20), and the resulting effect on reproduction, energy homeostasis, and anxiety. We found that the Smim20 knockout mice had normal fertility and estrous cycle lengths. Consistent with normal fertility, the hypothalamii of the knockout mice showed no changes in the levels of reproduction-related genes, but the male mice had some changes in energy homeostasis-related genes, such as melanocortin receptor 4 (Mc4r). When placed on a high-fat diet, the wildtype and knockout mice responded similarly, but the male heterozygous mice gained slightly less weight. When placed in an open field test box, the female knockout mice traveled less distance in the outer zone, indicating alterations in anxiety or locomotor behavior. In summary, the homozygous knockout of PNX did not alter fertility and modestly alters a few neuroendocrine genes in response to a high-fat diet, especially in the female mice. However, it altered the behavior of mice in an open field test. PNX therefore may not be crucial for reproductive function or weight, however, we cannot rule out possible compensatory mechanisms in the knockout model. Understanding the role of PNX in physiology may ultimately lead to an enhanced understanding of neuroendocrine mechanisms involving this enigmatic peptide.

Achieving a Water-Resilient Rotterdam: Past, Present and Future Perspectives

Achieving a Water-Resilient Rotterdam: Past, Present and Future Perspectives

Performance of cut-off walls under long-term vacuum suction: A case study

This study assesses the performance of cut-off walls in a vacuum preloading project at Lianyungang Port, China, to tackle challenges posed by ultra-soft reclaimed land. It investigates the walls’ impermeability and structural integrity by analyzing changes in hydraulic conductivity, in-situ lateral displacement, particle size distribution, and dry density both before and after vacuum suction. The introduction of a hydroxypropyl starch-based coupling agent (CA) in slurry reduces the hydraulic conductivity in the sandy matrix. Significant lateral displacement near the surface amplifies the likelihood of cracks, which lead to increased hydraulic conductivity. The cut-off wall is characterized by three zones: an erosion zone with large amount of fine particle mobility, a central effective zone with minimal deformation, and an outer tensile zone whose soil loosening leads to impermeability reduction. These findings provide valuable insights into the design and construction of cut-off walls for similar geotechnical applications and aid in forecasting the performance and lifespan of the cut-off wall.

Disparities in Cancer Stage Outcomes by Catchment Areas for a Comprehensive Cancer Center

The National Cancer Institute comprehensive cancer centers (CCCs) lack spatial and temporal evaluation of their self-designated catchment areas. To identify disparities in cancer stage at diagnosis within and outside a CCC's catchment area across a 10-year period using spatial and statistical analyses. This cross-sectional, population-based study conducted between 2010 and 2019 utilized cancer registry data for the Johns Hopkins Sidney Kimmel CCC (SKCCC). Eligible participants included patients with cancer in the contiguous US who received treatment for cancer, a diagnosis of cancer, or both at SKCCC. Patients were geocoded to zip code tabulation areas (ZCTAs). Individual-level variables included sociodemographic characteristics, smoking and alcohol use, treatment type, cancer site, and insurance type. Data analysis was performed between March and July 2023. Distance between SKCCC and ZCTAs were computed to generate a catchment area of the closest 75% of patients and outer zones in 5% increments for comparison. The primary outcome was cancer stage at diagnosis, defined as early-stage, late-stage, or unknown stage. Multinomial logistic regression was used to determine associations of catchment area with stage at diagnosis. This study had a total of 94 007 participants (46 009 male [48.94%] and 47 998 female [51.06%]; 30 195 aged 22-45 years [32.12%]; 4209 Asian [4.48%]; 2408 Hispanic [2.56%]; 16 004 non-Hispanic Black [17.02%]; 69 052 non-Hispanic White [73.45%]; and 2334 with other or unknown race or ethnicity [2.48%]), including 47 245 patients (50.26%) who received a diagnosis of early-stage cancer, 19 491 (20.73%) who received a diagnosis of late-stage cancer , and 27 271 (29.01%) with unknown stage. Living outside the main catchment area was associated with higher odds of late-stage cancers for those who received only a diagnosis (odds ratio [OR], 1.50; 95% CI, 1.10-2.05) or only treatment (OR, 1.44; 95% CI, 1.28-1.61) at SKCCC. Non-Hispanic Black patients (OR, 1.16; 95% CI, 1.10-1.23) and those with Medicaid (OR, 1.65; 95% CI, 1.46-1.86) and no insurance at time of treatment (OR, 2.12; 95% CI, 1.79-2.51) also had higher odds of receiving a late-stage cancer diagnosis. In this cross-sectional study of CCC data from 2010 to 2019, patients residing outside the main catchment area, non-Hispanic Black patients, and patients with Medicaid or no insurance had higher odds of late-stage diagnoses. These findings suggest that disadvantaged populations and those living outside of the main catchment area of a CCC may face barriers to screening and treatment. Care-sharing agreements among CCCs could address these issues.

Dynamics of microplastic abundance under tidal fluctuation in Musi estuary, Indonesia

Tidal dynamics contribute to fluctuations in microplastic abundance (MPs). This is the first study to characterize MPs under the influence of tidal fluctuations in the Musi River Estuary. MPs samples were collected during flood and ebb tides at 10 research stations representing the inner, middle and outer parts of the Musi River Estuary. MPs were extracted to identify the shape, color and size. MP abundances were 467.67 ± 127.84 particles/m3 during flood tide and 723.67 ± 112.05 particles/m3 during ebb tide. The concentration of MPs in the outer zone of the estuary (ocean) was detected to be higher than in the inner zone of the estuary (river). The MPs found were dominated by black color, film shape and size 101–250 μm. A greater abundance of MPs at ebb tide than at flood tide implies that the Musi Estuary's largest source of emissions is discharge from the river.

Advanced diffusion MRI provides evidence for altered axonal microstructure and gradual peritumoral infiltration in GBM in comparison to brain metastases

PurposeIn contrast to peritumoral edema in metastases, GBM is histopathologically characterized by infiltrating tumor cells within the T2 signal alterations. We hypothesized that depending on the distance from the outline of the contrast-enhancing tumor we might reveal imaging evidence of gradual peritumoral infiltration in GBM and predominantly vasogenic edema around metastases. We thus investigated the gradual change of advanced diffusion metrics with the peritumoral zone in metastases and GBM.MethodsIn 30 patients with GBM and 28 with brain metastases, peritumoral T2 hyperintensity was segmented in 33% partitions based on the total volume beginning at the enhancing tumor margin and divided into inner, middle and outer zones. Diffusion Tensor Imaging (DTI)-derived fractional anisotropy and mean diffusivity as well as Diffusion Microstructure Imaging (DMI)-based parameters Dax-intra, Dax-extra, V‑CSF and V-intra were employed to assess group-wise differences between inner and outer zones as well as within-group gradients between the inner and outer zones.ResultsIn metastases, fractional anisotropy and Dax-extra were significantly reduced in the inner zone compared to the outer zone (FA p = 0.01; Dax-extra p = 0.03). In GBM, we noted a reduced Dax-extra and significantly lower intraaxonal volume fraction (Dax-extra p = 0.008, V‑intra p = 0.006) accompanied by elevated axial intraaxonal diffusivity in the inner zone (p = 0.035). Between-group comparison of the outer to the inner zones revealed significantly higher gradients in metastases over GBM for FA (p = 0.04) as well as the axial diffusivity in the intra- (p = 0.02) and extraaxonal compartment (p < 0.001).ConclusionOur findings provide evidence of gradual alterations within the peritumoral zone of brain tumors. These are compatible with predominant (vasogenic) edema formation in metastases, whereas our findings in GBM are in line with an axonal destructive component in the immediate peritumoral area and evidence of tumor cell infiltration with accentuation in the tumor’s vicinity.

Morphology and Kinematics of the Gas in M51: How Interaction with NGC 5195 Has Molded the Structure of Its Arms

The Whirlpool Galaxy is a well-studied grand design galaxy with two major spiral arms, and a large satellite NGC 5195. The arms both show long uniform sections with perturbations (“kinks” or sharp turns) in specific regions. Comparing the two arms shows a small radial offset between the main kinked regions. We analyzed the morphology and also the velocity field in the disk of M51 using kinematic maps based on Hα and CO line emission. These sample complementary radial ranges, with the CO map covering the central zone and the Hα map extending to cover the outer zone. We looked for indicators of density wave resonance, zones where radial flows of gas in the disk plane reverse their sign. These were present in both velocity maps; their 2D localization placed them along or closely parallel to the spiral arms, at a set of well-defined galactocentric radii, and notably more concentrated along the southern, stronger arm. The results can be well interpreted quantitatively, using a numerical model of the interaction of M51 and NGC 5195 in which the satellite has made two relatively recent passes through the disk plane of M51. During the first pass the pair of dominant spiral arms was stimulated, and during the second pass the strong kinks in both arms were formed at about the same time. The second interaction is particularly well characterized, because the timescale corresponding to the production of the kinks and the recovery of the original pitch angle is identical for the two arms.

Structural Evolution of the Northern Agrio Fold and Trust Belt (∼37°30′S), Neuquén Basin, Argentina, Derived From Low‐Temperature Multi‐Thermochronometry

AbstractThe Agrio Fold and Thrust Belt (FTB), situated in the Southern Central Andes at 37–39°S, underwent two phases of contractional deformation: Late Cretaceous‐Eocene and middle‐late Miocene. Despite advances in understanding its tectonic history, many questions persist regarding the timing and activity of specific structures during these deformation phases. By combining low‐temperature multi‐thermochronometry, inverse thermal models and field structural data, we present a new thermal‐structural history for the northern Agrio FTB. Our findings unveil an initial cooling event between approximately 85–75 Ma and 55–50 Ma, involving cooling rates of 1.1–2°C/Ma and vertical displacement rates from 0.07 to 0.12 km/Ma. This slow event, confined to the inner zone, is associated with the growth of the basement‐cored Manzano anticline. Additionally, still in the inner zone of the Agrio FTB, a second and faster cooling event from ∼15–10 Ma to 0 Ma, marked by a cooling rate of 7°C/Ma and a vertical displacement rate ranging from 0.11 to 0.17 km/Ma, results from in‐sequence thick‐skinned thrusting at depth. In the outer zone of the FTB, only the younger cooling event from 15–10 Ma to 0 Ma is evident, with a cooling rate of 8.8°C/Ma and a vertical displacement rate ranging from ∼0.14 to 0.26 km/Ma, attributed to displacement along the basement‐involved Las Yeseras thrust. Furthermore, Apatite Fission Track (AFT) ages of detrital grains in the Tralalhué conglomerates support the maximum depositional age for these synorogenic strata to be between 14.1 and 9.2 Ma.

Evolution of reservoir quality related to clay coating overgrowths in tight sandstone in the fluvial facies of the southeastern Sichuan Basin

As a result of silicate overgrowth, clay coatings influence the evolution of reservoir quality during diagenesis. Most studies indicate coatings can resist compaction and inhibit cementation, thus preserving primary porosity and serving as one of the primary controlling factors for improving reservoir quality. However, some research suggests clay coatings have insufficient hardness to resist compaction and could potentially block pore throats and prevent fluid flow within the sandstone, negatively affects reservoir quality. Therefore, to address whether coatings are positive to reservoir evolution, this study employs polarized light microscopy, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and porosity-permeability testing to investigate the characteristics of clay coatings within the fluvial facies sandstone of the Xiashaximiao Formation. The microscopy reveals abundant clay coatings were found, mainly in lithic-arenite with 30%–45% feldspar and rock fragments. The underlying Lianggaoshan Formation locally exhibits interbedded siltstones with volcanic rock fragments, providing material sources for the clay coatings formation. SEM and EDX analyses indicate two predominant forms of clay coatings: single-layer (primarily chlorite) and double-layer (inner smectite/illite, outer ferroan chlorite). Single-layer overgrowths primarily consist of thin layers of chlorite (5–15 μm), whereas double-layer overgrowths consist of a thin inner zone (1–5 μm) covering the grain surface and a thicker outer zone (10–20 μm) covering the inner zone, demonstrating characteristics indicative of multi-stage growth. Porosity-permeability testing results the sandstone samples have <10% porosity, which are typically tight sandstones, but those with clay coatings have higher porosity. Nevertheless, sandstones with double-layer overgrowths exhibit lower permeability relative to those with single-layer overgrowths or without overgrowths. Therefore, based on the integration of morphological and physical properties of silicate overgrowths, it is proposed the efficiency of clay coatings in resisting compaction, inhibiting cementation, and preserving primary porosity increases with the number of growth stages, layers, and thickness, which in turn depends on the abundance of source materials. Single-layer coatings facilitate fluid migration, whereas thicker double-layer overgrowths are prone to occluding narrow pore throats, thereby restricting fluid mobility. Consequently, this study establishes a model for the multi-stage evolution of clay coatings overgrowths, elucidating the varying fluid migration behaviors across different stages and providing a more detailed investigation of the implication of clay coatings on reservoir quality, thus offering new theoretical insights into diagenesis and the evolution of tight sandstone reservoirs.