Oscillatory Strain Research Articles

Microstructural analysis on the compatibility of various dilution oils on magnetorheological grease performance

This research explores the effects of dilution oils on the storage stability of magnetorheological grease (MRG) by studying the effect of dilution oil viscosity on the microstructure of carrier fluids medium for MRG, which can help address practical challenges encountered in the development and deployment of MRG. Three samples of MRG with 70 wt% CIP are prepared; a control, and 2 samples diluted until 10 wt% hydraulic fluid and kerosene respectively. The resulting samples were analysed using a modular compact rheometer (MCR) for oscillatory strain sweep and rotational current sweep. Rheological analyses were repeated after one year in storage. Fourier-Transform Infrared (FTIR) spectroscopy and Atomic Force Microscopy (AFM) results show significant microstructural and performance deterioration of grease thickener in the sample with kerosene, which concludes that kerosene had a very significant effect on the degradation of the grease thickener. From this study, it was revealed that low viscosity oils disrupt the reconstruction of the thickener of lithium grease, which in turn causes deteriorating shear rheological performance of MRG at off-state conditions. This comprehensive analysis explains the relationships between MRG composition, microstructural characteristics, and performance parameters, offering a foundational framework for further exploration and advancement in this scientific field.

Can plant-based cheese alternatives be characterized by methods for dairy cheese? Extending dairy cheese methods to characterize plant-based cheese alternatives

The techno-functional properties of dairy cheeses are often superior to their plant-based cheese alternatives. However, the constant increase in demand for plant-based cheese alternatives makes it important to achieve texture and functionality as in dairy cheeses. In this study commercial dairy cheeses and plant-based cheese alternatives were analyzed in regard to chemical composition, texture properties (unheated and heated state) and melting behavior with methods commonly applied to dairy cheeses. Especially, during an oscillatory temperature sweep, data did not show the “melting” the consumer notices while baking the product in an oven as done in the Schreiber test (2_CA, 3_CA). Therefore, a large amplitude oscillatory strain method (LAOS 60 °C) was applied and linked with the results obtained from the Schreiber test and the temperature sweep measurements. LAOS not only showed good correlation with the melting behavior observed in the Schreiber test but also allowed conclusions about the microstructure of the samples.

Capturing Catalyst Strain Dynamics during Operando CO Oxidation.

Understanding the strain dynamic behavior of catalysts is crucial for the development of cost-effective, efficient, stable, and long-lasting catalysts. Using time-resolved Bragg coherent diffraction imaging at the fourth generation Extremely Brilliant Source of the European Synchrotron (ESRF-EBS), we achieved subsecond time resolution during operando chemical reactions. Upon investigation of Pt nanoparticles during CO oxidation, the three-dimensional strain profile highlights significant changes in the surface and subsurface regions, where localized strain is probed along the [111] direction. Notably, a rapid increase in tensile strain was observed at the top and bottom Pt {111} facets during CO adsorption. Moreover, we detected oscillatory strain changes (6.4 s period) linked to CO adsorption during oxidation, where a time resolution of 0.25 s was achieved. This approach allows for the study of adsorption dynamics of catalytic nanomaterials at the single-particle level under operando conditions, which provides insight into nanoscale catalytic mechanisms.

Rheological softening of metal nanocontacts sheared under oscillatory strains

Rheological softening of metal nanocontacts sheared under oscillatory strains

The Production of Three-Dimensional Metal Objects Using Oscillatory-Strain-Assisted Fine Wire Shaping and Joining.

Material shaping and joining are the two fundamental processes that lie at the core of many forms of metal manufacturing techniques, including additive manufacturing. Current metal additive manufacturing processes such as laser/e-beam powder bed fusion and Directed Energy Deposition predominantly use heat and subsequent melt-fusion and solidification to achieve shaping and joining. The energy efficiency of these processes is severely limited due to energy conversion losses before energy is delivered at the point of melt-fusion for shaping and joining, and due to losses through heat transfer to the surrounding environment. This manuscript demonstrates that by using the physical phenomenon of lowered yield stress of metals and enhanced diffusion in the presence of low amplitude high frequency oscillatory strain, metal shaping and joining can be performed in an energy-efficient way. The two performed simultaneously enable a metal additive manufacturing process, namely Resonance-Assisted Deposition (RAD), that has several unique capabilities, like the ability to print net-shape components from hard-to-weld alloys like Al6061 and the ability to print components with a very high aspect ratio. In this study, we show this process's capabilities by printing solid components using aluminum-based metal alloys.

Rheological Analysis on Hardening of Magnetorheological Grease with Kerosene

Magnetorheological grease (MRG) with dilution oils may suffer from reduced storage stability caused by oil separation. This phenomenon potentially causes a performance reduction of the material due to possible accelerated degradation of the grease medium. The long-term rheological behavior of MRG with kerosene (MRGK) was investigated in this study. MRGK was prepared with 10 wt% kerosene as the dilution oil, together with a sample of MRG without any kerosene as the control. A modular compact rheometer (MCR) was used to obtain rheological data from the MRG samples in an oscillatory strain sweep mode under the influence of magnetic fields, which ranged from 0A to 3A. After one year, the measurement was repeated to observe any changes to the rheology of MRG samples. Results showed a significant hardening of the sample diluted with kerosene, which mainly showed a drastic increase in off-state storage modulus at low strain. This was shown by the off-state storage modulus of MRGK, which after one year showed an increase of 15% in the initial storage modulus, and an increase of 2438% in the storage modulus at 10% strain. The MRG sample showed an increase of 50% and 47%, respectively. The on-state storage modulus did not appear to experience such a drastic change after one year. The study concluded that while dilution oil may be a promising candidate to reduce the initial viscosity of MRG, the resulting performance difference may compromise the long-term performance, and may even cause accelerated degradation when in use.

Transition condition between memories of vibration and flow in the memory effect of paste.

Because of its plasticity, a densely packed colloidal suspension, called a paste, remembers directions of its motion, such as vibration and flow. When it dries, primary desiccation cracks propagate in a direction perpendicular to the direction of its vibrational motion and parallel to the direction of its flow motion, which are memory effects of paste. Application of an oscillatory shear strain to a paste using a rheometer reveals that the transition from memory of vibration to that of flow is induced when the amplitude of the oscillatory shear strain exceeds a threshold value. Findings also demonstrate that oscillatory motion is unnecessary, i.e., merely a large shear deformation is sufficient for the memory of flow. Therefore, only oscillatory shear strain with a small amplitude is necessary for memory of vibration; large shear deformation is sufficient for memory of flow.

Active Pulsatile Gels: From a Chemical Microreactor to a Polymeric Actuator.

We report on a synthesis protocol, experimental characterization, and theoretical modeling of active pulsatile Belousov-Zhabotinsky (BZ) hydrogels. Our two-step synthesis technique allows independent optimization of the geometry, the chemical, and the mechanical properties of BZ gels. We identify the role of the surrounding medium chemistry and gel radius for the occurrence of BZ gel oscillations, quantified by the Damköhler number, which is the ratio of chemical reaction to diffusion rates. Tuning the BZ gel size to maximize its chemomechanical oscillation amplitude, we find that its oscillatory strain amplitude is limited by the time scale of gel swelling relative to the chemical oscillation period. Our experimental findings are in good agreement with a Vanag-Epstein model of BZ chemistry and a Tanaka Fillmore theory of gel swelling dynamics.

Collective chemomechanical oscillations in active hydrogels

We report on the collective response of an assembly of chemomechanical Belousov-Zhabotinsky (BZ) hydrogel beads. We first demonstrate that a single isolated spherical BZ hydrogel bead with a radius below a critical value does not oscillate, whereas an assembly of the same BZ hydrogel beads presents chemical oscillation. A BZ chemical model with an additional flux of chemicals out of the BZ hydrogel captures the experimentally observed transition from oxidized nonoscillating to oscillating BZ hydrogels and shows this transition is due to a flux of inhibitors out of the BZ hydrogel. The model also captures the role of neighboring BZ hydrogel beads in decreasing the critical size for an assembly of BZ hydrogel beads to oscillate. We finally leverage the quorum sensing behavior of the collective to trigger their chemomechanical oscillation and discuss how this collective effect can be used to enhance the oscillatory strain of these active BZ hydrogels. These findings could help guide the eventual fabrication of a swarm of autonomous, communicating, and motile hydrogels.

Rheology of paste-like food inks for 3D printing: Effects of nutrient and water content

This research delves into understanding the effects of composition on the rheological response of multi-component food inks for 3D food printing. Accordingly, the motivation is to decouple the nutrient and water content effects on the rheology. We formulated inks by combining pea fractions with water and employing a water-holding-capacity based hydration method. Rheology is characterized by steady shear rate and oscillatory strain amplitude sweeps. Strain sweep curves infer that the deformation response of all inks follows a similar trend, and samples sharing the same macronutrient formulation are mapped to a master curve after scaling with the elastic plateau modulus. Samples sharing the same macronutrient formulation mapped to a master curve after scaling with the elastic modulus. Shear rate testing showed that the inks were shear thinning yield stress materials. Shear rate sweeps also collapsed on a master curve scaled by the yield stress and critical shear rate on the y and x axes. The yield stress and the plateau modulus appeared to be controlled by the water content, while the shear and strain thinning exponents were independent of the formulations, inferring that the rheology is scaled by the water content while preserving the shear thinning response. Observing the independence of the rheological properties from the nutrient composition and scalability of the rheology by the water content provided a step forward in developing formulations with various nutrient content at desired ow properties, which promises personalized nutrition. Furthermore, the study shows the applicability of various rheological techniques, which are expected to contribute to the literature on the rheology of granular pastes.

Dual functionality of the BiN monolayer: unraveling its photocatalytic and piezocatalytic water splitting properties.

To achieve scalable and economically viable green hydrogen (H2) production, the photocatalytic and piezocatalytic processes are promising methods. The key to successful overall water splitting (OWS) for H2 production in these processes is using suitable semiconductor catalysts with appropriate band edge potentials, efficient optical absorption, higher mechanical flexibility, and piezoelectric coefficients. Thus, we explore the bismuth nitride (BiN) monolayer using density functional theory simulations, revealing intriguing catalytic properties. The BiN monolayer is a semiconductor with an indirect electronic bandgap (Eg) of 2.08 eV and displays excellent visible light absorption (approximately 105 cm-1). Detailed analyses show that the band edges satisfy the redox potential for photocatalytic OWS via biaxial strain engineering and pH variation. Notably, the solar to hydrogen conversion efficiency (ηSTH) for the BiN monolayer can reach 17.18%, which exceeds the 10% efficiency limit of photocatalysts for economical green H2 production. The obtained in-plane piezoelectric coefficient of e11 = 16.18 Å C m-1 is superior to widely studied 2D materials. Moreover, the generated piezopotential under oscillatory strain stands at 28.34 V, which can initiate the water redox reaction via the piezocatalytic mechanism. This originates from the mechanical flexibility coupled with higher piezoelectric coefficients. The result highlights the BiN monolayer's potential application in photocatalytic, piezocatalytic, and photo-piezo-catalytic OWS.

Reversible-to-irreversible transition of colloidal polycrystals under cyclic athermal quasistatic deformation.

Cyclic loading on granular packings and amorphous media exhibits a transition from reversible elastic behavior to irreversible plasticity. The present study compares the irreversibility transition and microscopic details of colloidal polycrystals under oscillatory tensile-compressive and shear strain. Under both modes, the systems exhibit a reversible to irreversible transition. However, the strain amplitude at which the transition is observed is larger in the shear strain than in the tensile-compressive mode. The threshold strain amplitude is confirmed by analyzing the dynamical properties, such as mobility and atomic strain (von Mises shear strain and the volumetric strain). The structural changes are quantified using a hexatic order parameter. Under both modes of deformation, dislocations and grain boundaries in polycrystals disappear, and monocrystals are formed. We also recognize the dislocation motion through grains. The key difference is that strain accumulates diagonally in oscillatory tensile-compressive deformation, whereas in shear deformation, strain accumulation is along the x or y axis.

Characterization of novel alginate-Aloe Vera raft systems for treatment of gastroesophageal reflux disease

Raft-forming systems are designed to relieve reflux symptoms by forming a physical barrier on top of the stomach. The present study aimed to evaluate the physico-chemical properties of alginate-aloe vera raft-forming systems for the first time. To achieve this goal, aloe vera was used in the proportion of 1 and 1.5 % in raft suspensions containing 5 % alginate as the main component of gel structure. Rafts were characterized by their volume, floating behavior, thickness, swelling properties, strength, resilience, reflux resistance, and acid neutralization capacity (ANC). Results showed the effectiveness of aloe vera in forming rafts that were voluminous, buoyant with greater total floating time (TFT), and stronger than formulations with no aloe vera. Furthermore, data showed that the presence of aloe vera could improve resilience time, swelling proportions, resistance to reflux under simulant conditions of movement in the stomach, and ANC values of rafts. Rafts were further characterized by oscillatory strain sweep test, differential scanning calorimetry, and Fourier transform infrared spectroscopy. Evaluation of the mechanical properties of rafts displayed a viscoelastic behavior of gels corresponding to the internal cross-linked structure of rafts. This study demonstrated that designing of alginate-aloe vera rafts can be suitable for the treatment of gastro-esophageal reflux disorders.

A new instrument for interfacial dilational rheology.

We present a new design for an interfacial dilational rheometer that can generate oscillatory dilational strain on a planar air-liquid interface. The strain is generated by a pneumatic mechanism involving a deformable film, which forms a circular barrier that can contract or expand under different pressures. The interfacial stress is measured using a Wilhelmy rod. We carefully examine and demonstrate the effects of potential sources of measurement error, including inertia, drag, buoyancy, flow from the bulk phase, and surface waves. The design avoids mixed deformations present in other instruments and is currently capable of accurate measurements at frequencies up to ∼0.1Hz and dilational strains below 0.001, with potential for higher frequencies after further theoretical development. We demonstrate the integration of the interfacial dilational rheometer with a Langmuir trough by measuring the compression isotherm of an insoluble surfactant, stearic acid. Furthermore, we verify the capability of the interfacial dilational rheometer to perform frequency and amplitude sweeps and present the storage and loss moduli for a water-soluble surfactant, sodium dodecylbenzenesulfonate, at different concentrations.

Rheological measurements and normal compression tests on shear thickening fluids below room temperature

This work concentrated on the rheological measurements and normal compression tests of a shear thickening fluid (STF) below room temperature from −20 to 20 °C. The STF was made of 20% of fumed silica and 80% ethylene glycol in weight fraction. Experimental measurements were conducted with a parallel plate MCR301 rheometer. Temperature dependency, steady-state tests, oscillatory fRequency sweep tests, oscillatory shear strain amplitude sweep tests, and normal compression tests were applied on STF, and the testing results were analysed and discussed. The temperature played an important role in the performance of STF. The low temperature increased the STF’s viscosity and shear thickening effect but decreased the STF’s critical shear rate. Frequency was found to contribute to the STF’s phase change from the liquid state to the solid state. The normal compression tests were conducted to determine the equivalent stiffness of STF under different temperatures and various shear rates. The results showed that the STF’s equivalent normal stiffness could be increased by either lowering the applied temperature or increasing the shear rate. A mathematical model was adopted to represent the viscosity of STF in the temperature range from −20 to 20 °C.

Viscoelastic response of confined powder under large strain oscillations, characterized by its noise temperature

We report a study on granular matter with and without small additions of silicon oil, under low-frequency and large amplitude oscillatory shear strain under constant normal pressure, by running experiments with a rotational rheometer with a cup-and-plate geometry. We analysed the expansion with the Chebyshev polynomials of the orthogonal decomposition of stress–strain Lissajous–Bowditch loops. We found the onset of the strain amplitude for the yielding regime indicated a regime change from filament-like structures of grains to grain rearrangements for the dry granulate and from oscillations to the breaking and regeneration of liquid bridges for wet granulates. We have shown that this viscoelastic dynamics can be characterized by a noise temperature following Sollich et al. (Phys Rev Lett https://doi.org/10.1103/PhysRevLett.78.2020, 1997). The analysis of the first harmonics of the Chebyshev expansion showed that the state of disorder of dry and wet granular matter in pre-yielding and yielding regimes involved ensembles of different inherent states; thus, each of them was governed by a different noise temperature. The higher-order harmonics of the Chebyshev expansion revealed a proportionality between the viscous nonlinearity and the variation in the elastic nonlinearity induced by the deformation, which shows the coupling between the elastic deformation and the viscous flow of mesoscopic-scale structures.Graphic abstract

Comparison of Deformation Patterns Excited in the Human Brain In Vivo by Harmonic and Impulsive Skull Motion.

Noninvasive measurements of brain deformation in human participants in vivo are needed to develop models of brain biomechanics and understand traumatic brain injury (TBI). Tagged magnetic resonance imaging (tagged MRI) and magnetic resonance elastography (MRE) are two techniques to study human brain deformation; these techniques differ in the type of motion and difficulty of implementation. In this study, oscillatory strain fields in the human brain caused by impulsive head acceleration and measured by tagged MRI were compared quantitatively to strain fields measured by MRE during harmonic head motion at 10 and 50 Hz. Strain fields were compared by registering to a common anatomical template, then computing correlations between the registered strain fields. Correlations were computed between tagged MRI strain fields in six participants and MRE strain fields at 10 Hz and 50 Hz in six different participants. Correlations among strain fields within the same experiment type were compared statistically to correlations from different experiment types. Strain fields from harmonic head motion at 10 Hz imaged by MRE were qualitatively and quantitatively similar to modes excited by impulsive head motion, imaged by tagged MRI. Notably, correlations between strain fields from 10 Hz MRE and tagged MRI did not differ significantly from correlations between strain fields from tagged MRI. These results suggest that low-frequency modes of oscillation dominate the response of the brain during impact. Thus, low-frequency MRE, which is simpler and more widely available than tagged MRI, can be used to illuminate the brain's response to head impact.

Antibodies Adsorbed to the Air-Water Interface Form Soft Glasses.

When monoclonal antibodies are exposed to an air-water interface, they form aggregates, which negatively impacts their performance. Until now, the detection and characterization of interfacial aggregation have been difficult. Here, we exploit the mechanical response imparted by interfacial adsorption by measuring the interfacial shear rheology of a model antibody, anti-streptavidin immunoglobulin-1 (AS-IgG1), at the air-water interface. Strong viscoelastic layers of AS-IgG1 form when the protein is adsorbed from the bulk solution. Creep experiments correlate the compliance of the interfacial protein layer with the subphase solution pH and bulk concentration. These, along with oscillatory strain amplitude and frequency sweeps, show that the viscoelastic behavior of the adsorbed layers is that of a soft glass with interfacial shear moduli on the order of 10-3 Pa m. Shifting the creep compliance curves under different applied stresses forms master curves consistent with stress-time superposition of soft interfacial glasses. The interfacial rheology results are discussed in the context of the interface-mediated aggregation of AS-IgG1.

A self-healable and injectable hydrogel for pH-responsive doxorubicin drug delivery in vitro and in vivo for colon cancer treatment

Hydrogels are three-dimensional solid-like structures with a wide range of applications in drug transport, tissue engineering, wound dressing, etc. We developed herein a new hydrogel by mixing 5′-guanosine monophosphate (5′-GMP) disodium salt (16 mM) and 1,4,5,8-naphthalene tetracarboxylic acid tetra potassium salt (NAP) (4 mM) in 4:1 (GMP:NAP) stoichiometry in aqueous media (pH ∼4 at 25 °C). The mechanical properties of the resulting hydrogel were investigated by rheological studies, which showed that the hydrogel formed at pH 4 is the most stable [storage modulus (Gꞌ) of ∼4000 Pa] and has higher endurance for the oscillatory strain (20% strain). Spectroscopic investigations provided insights into the unique self-assembly of 5′-GMP and NAP. Further, the composite exhibited pH-responsive hydrogelation over the pH range of 3–6, and the gel was transformed into a sol form at pH > 5. This stimuli-sensitive nature of the hydrogel was then exploited for the encapsulation and efficacious delivery of an anticancer drug, doxorubicin (DOX), specifically toward the colorectal cancer. Microscopic studies revealed the presence of a regular entangled fibrillar network for the hydrogels, which allowed for its exceptionally high drug loading capacity. The controlled release of DOX from the hydrogel was then studied at the physiological pH of the gastrointestinal tract, i.e. pH ∼7.4. The DOX-loaded hydrogel (DOX-Gel) exhibited a ∼82% release of DOX over 100 h at pH ∼7.4. The enhanced cellular toxicity of DOX was observed in CT-26 murine colorectal carcinoma cell lines treated with the DOX-loaded hydrogel compared to DOX only as manifested from the fluorescence-activated cell sortinganalyses and fluorescence microscopic studies. The fluorescence-activated cell sorting analysis showed a ∼4.5-fold increase in the drug internalization for the DOX-Gel as compared to DOX only formulations. The co-localization of DOX into the cell nucleus was confirmed from confocal microscopy. The in vivo drug delivery efficacy of this pH-responsive hydrogel was further assessed on an animal tumor model, Balb/c mice (n = 9). A significant regression of ∼87.5% in the tumor volume was observed after 21 days of DOX-gel administration, in contrast to DOX only formulation, which showed only a ∼46.0% regression in the tumor volume. The blood reports of the non-treated control mice and the mice treated with DOX only indicated a metastatic behavior in comparison with the mice treated with the DOX-Gel. This, the present system, is a self-healable, injectable hydrogel, which makes it an ideal drug delivery vehicle with stimuli-responsive controlled drug release capabilities even in vivo.

Quantitative measurements of changes in agglomerate size with oscillatory shear strain in polymer nanocomposites using online dielectric analysis

Shear strains during processing affect the agglomerate size of nanoparticles in nanocomposites and their final behavior in various applications. In this study, dielectric characterization technique as a novel and well-effective method is applied for quantitative measurement of average agglomerate size in polymer nanocomposites under shear strain sweep, combining with an existing analytical model. Examining how changes in filler content, surface energy and polarity of particles and the matrix control the strain-dependency of agglomerates size, two different nanoparticles, namely, titanium dioxide (TiO2) and carbon black (CB), with same average diameters and volumes were added to polystyrene (PS). It was found that larger agglomerates were present in the PS/CB nanocomposite prior to shearing and the CB agglomerates were less prone to deagglomeration under shear strain. This behavior was attributed to higher polarity of CB nanoparticles, leading to higher tendency for agglomeration and higher resistance to shear, in respect to TiO2 nanoparticles.