Organic Stationary Phase Research Articles

Pilot‐scale ion‐exchange centrifugal partition chromatography: Purification of sinalbin from white mustard seeds

The purification of p-hydroxybenzylglucosinolate (sinalbin) on a multigram scale from a crude aqueous extract of white mustard seeds (Sinapis alba var. concerta) was successfully achieved by scaling up a strong ion-exchange centrifugal partition chromatography (SIXCPC) laboratory procedure. Thus, the one-step sinalbin purification was performed with 2.35 g of crude extract in approximately 170 min (830 mg/h) up to 70.3 g in approximately 160 min (26.3 g/h) by switching from a 200 mL laboratory scale column to a 5.7 L pilot-scale column. The required biphasic solvent system contained ethyl acetate, n-butanol, and water in 3:2:5 v/v/v proportions, Aliquat 336 (trioctylmethyl ammonium chloride) was added to the organic stationary phase (80 mM) and acted as ion-exchanger. Potassium iodide in the aqueous mobile phase (80 mM) was used as sinalbin displacer. The 28.5 mass scale factor arose from the increase in mobile phase flow-rate (from 2 to 50 mL/min), from the higher mass of injected white mustard seed extract (from 12 to 350 g), and from the calculated productivity (from 830 mg to 26.3 g). These results demonstrate that industry scale production of glucosinolates is easily performed by SIXCPC, thus providing pure reference standards for pharmacology studies.

Large-scale separation of clavine alkaloids from Ipomoea muricata by pH-zone-refining centrifugal partition chromatography

Centrifugal partition chromatography in the pH-zone-refining mode was successfully applied to the separation of alkaloids, directly from a crude extract of Ipomoea muricata. The experiment was performed with a two-phase solvent system composed of methyl tert-butyl ether (MtBE)–acetonitrile–water (4:1:5, v/v) where triethylamine (10 mM) was added to the upper organic stationary phase as a retainer and trifluoroacetic acid (10 mM) to the aqueous mobile phase as an eluter. From 4 g of crude extract, 210 mg lysergol and 182 mg chanoclavine were obtained in 97% and 79.6% purities. Total yield recovery was >95%. Isolated alkaloids were characterized on the basis of their 1H, 13C NMR and ESI-MS data.

Use of pH-Zone Refining Countercurrent Chromatography for Preparative Separation of Fangchinoline and Tetrandrine from Stephania tetrandra

pH-Zone-refining countercurrent chromatography with a multilayer coil planet centrifuge has been successfully used for separation of fangchinoline and tetrandrine from crude extracts of Stephania tetrandra. The two target compounds were completely resolved by use of the two-phase solvent system petroleum ether (60–90 °C)–ethyl acetate–methanol–water 5:5:1:9 (v/v), with 10 mm triethylamine in the organic stationary phase and 5 mm hydrochloric acid in the aqueous mobile phase. Separation of 3.5 g sample yielded 126 mg fangchinoline (LC purity >93%) and 249 mg tetrandrine (LC purity >95%). The structures of the compounds were confirmed by use of electrospray ionization mass spectrometry and 1H NMR.

Preparative separation of di- and trisulfonated components of Quinoline Yellow using affinity-ligand pH-zone-refining counter-current chromatography

Four positionally isomeric 2-(2-quinolinyl)-1 H-indene-1,3(2 H)-dionedisulfonic acids (SA) and one triSA, components of the color additive Quinoline Yellow (QY, Color Index No. 47005), were isolated from the dye mixture by affinity-ligand pH-zone-refining counter-current chromatography (CCC) through complementary use of ion-exchange and ion-pair reagents as the ligand. The added ligands facilitated the partitioning of the very polar polysulfonated components into the organic stationary phase of the two-phase solvent systems that consisted of isoamyl alcohol–methyl tert-butyl ether–acetonitrile–water (3:5:1:7), (3:4:1:7) or (3:1:1:5). Thus, separation of a 5-g portion of QY using sulfuric acid as the retainer and dodecylamine as the ligand (an ion-exchange reagent, 20% in the stationary phase), resulted in 1.21 g of 6′,5-diSA and 1.69 g of 6′,8′,5-triSA, both of over 99% purity. A minor component, 8′,4-diSA, not previously reported was also obtained (4.8 mg of over 94% purity) through a similar separation of a different batch of QY using hydrochloric acid as the retainer and 10% dodecylamine as the ligand in the stationary phase. Two components that co-eluted (0.55 g) in the 5 g separation were separated when trifluoroacetic acid was used as the retainer and tetrabutylammonium hydroxide (an ion-pair reagent) as the ligand. The separation resulted in 20.7 mg of 6′,4-diSA, not previously reported, and 111.8 mg of 8′,5-diSA, both of over 98% purity. The isolated compounds were characterized by high-resolution mass spectrometry and proton nuclear magnetic resonance with correlated spectroscopy assignments.

Separation and purification of harmine and harmaline from Peganum harmala using pH‐zone‐refining counter‐current chromatography

pH-zone-refining counter-current chromatography was successfully applied to the separation of alkaloids from a crude extract of Peganum harmala L. using a multilayer coil planet centrifuge. The experiment was performed with a two-phase solvent system composed of methyl tert-butyl ether/THF/water (2:2:3 by volume) where triethylamine (10 mM) was added to the upper organic stationary phase as a retainer and hydrochloric acid (5 mM) to the aqueous mobile phase as an eluter. From 1.2 g of the crude extract, 554 mg harmine and 325 mg harmaline were obtained each with a purity of over 96% as determined by HPLC. The structures of the isolated compounds were identified by electron ionization MS (EI-MS), (1)H NMR, and (13)C NMR.

Separation of betalains from berries of Phytolacca americana by ion-pair high-speed counter-current chromatography

The first preparative fractionation of betalain pigments by means of ion-pair high-speed counter-current chromatography (IP-HSCCC) from berry extracts of Phytolacca americana (Phytolaccaceae) is presented. A novel HSCCC solvent system consisting of 1-butanol–acetonitrile–water (5:1:6, v/v/v) was applied using ion-pair forming trifluoroacetic acid at low concentration (0.7%, v/v). Affinity of polar betacyanins and betaxanthins to the organic stationary phase of the biphasic HSCCC solvent mixture was considerably improved. Partitioning coefficient values and influence of increasing trifluoroacetic acid additions to the biphasic solvent mixture were measured for all identified betacyanins and betaxanthins. Gentle separation by IP-HSCCC of the injected pigment extract (900 mg) yielded sufficient amounts of the principal pigments 15 S-betanin/15 R-isobetanin. The pure epimers separated by C 18-HPLC were immediately studied by one- and two-dimensional NMR. In the recovered fractions, minor concentrated betacyanins and betaxanthins were significantly enriched by IP-HSCCC and were detected for the first time in the extracts of P. americana. IP-HSCCC and C 18-HPLC were shown to be complementary techniques in the isolation procedure of recovering minor concentrated, highly polar and chemically instable betacyanins and betaxanthin from complex plant matrices. Altogether, identification of 17 betalains was achieved by HPLC-diode array detection-electrospray ionization MS/MS in the HSCCC fractions with their respective isomers, also resulting in the tentative elucidation of betacyanins with novel salicylic acid substitution pattern in the berry extracts of P. americana.

Large‐scale separation of salvianolic acid B from the Chinese medicinal plant Salvia miltiorrhiza by pH‐zone‐refining countercurrent chromatography

pH-Zone-refining countercurrent chromatography was successfully applied to the separation of salvianolic acid B from the Chinese medicinal plant, Salvia miltiorrhiza Bunge, using a multilayer coil planet centrifuge. A 2.0 g quantity of sample was separated using the following two-phase solvent system: methyl tert-butyl ether (MtBE)-water, 10 mM TFA in organic stationary phase and 10 mM ammonia in aqueous mobile phase. The obtained fractions were analyzed by HPLC and ESI-MS. The separation yielded 572 mg of the main component of salvianolic acid B with a purity of 94.1%.

A New Route for Preparation of High-density Organic Phase to High Selective HPLC for Polycyclic Aromatic Hydrocarbons by Atom-transfer Radical Polymerization of Octadecyl Acrylate on Silica

Abstract We have previously reported that poly(octadecyl acrylate) as an organic stationary phase in HPLC shows high molecular-shape selectivity through carbonyl–π interaction on highly ordered structures of long alkyl chains. In this communication, a new “grafting-from” strategy based on surface-initiated atom-transfer radical polymerization is applied for ordering of poly(octadecyl acrylate) on silica to lead to remarkable selectivity increase.

Selectivity Enhancement for trans-2-(2,3-Anthracenedicarboximido)-cyclohexane-derived Diastereomers in HPLC by Using an Ordered Organic Stationary Phase

2-(2,3-anthracenedicarboximido)cyclohexane derivatives (AC) have been known as the evolutionary diastereomerizing reagents for enantiomer discrimination in HPLC with ODS. However, a substantial separation of diastereomers can be observed only at lower temperatures, such as -40 degrees C. Therefore, in this work, poly(octadecyl acrylate)-grafted silica, ODAn was applied as an alternative stationary phase to ODS for the separation of AC-derived diastereomers. As a result, complete separation was achieved even under the conventional condition: for example, methanol as the mobile phase and 0 degrees C as the column temperature. An investigation on the temperature dependency of the selectivity demonstrated that ODAn shows a remarkable increase in selectivity at temperatures below 30 degrees C, which almost agreed with the peak-top temperature of the endothermic peak in a DSC thermogram for ODA35 immersed in a mobile phase. The better separation would be derived from a highly ordered structure of ODAn and a carbonyl-pi interaction with AC-derived diastereomers.

Large-scale separation of alkaloids from Corydalis decumbens by pH-zone-refining counter-current chromatography

pH-zone-refining counter-current chromatography was successfully applied to the separation of alkaloids from a crude extract of Corydalis decumbens (Thunb.) Pers. using a multilayer coil planet centrifuge (CPC). The experiment was performed with a two-phase solvent system composed of methyl tert-butyl ether (MtBE)–acetonitrile–water (2:2:3, v/v) where triethylamine (5–10 mM) was added to the upper organic stationary phase as a retainer and hydrochloric acid (5–10 mM) to the aqueous mobile phase as an eluter. From 3.1 g of the crude extract, 495 mg protopine, 626 mg tetrahydropalmatine and 423 mg bicuculline were obtained each with a purity of over 93% as determined by high performance liquid chromatography. The structures of the isolated compounds were identified by electron ionization mass spectrometry (EI–MS), high-performance liquid chromatography (HPLC)–electrospray ionisation–mass spectrometry (ESI–MS) and 1H NMR.

Preparative separation of cichoric acid from Echinacea Purpurea by pH-zone-refining counter-current chromatography

pH-zone-refining counter-current chromatography was successfully applied to the separation of cichoric acid from Echinacea Purpurea (L.) Moench. A 3.0 g quantity of sample was separated using the following two-phase solvent system: MtBE–CH 3CN–water (4:1:5, v/v), 10 mM trifluoroacetic acid in organic stationary phase and 10 mM ammonia in aqueous mobile phase. The obtained fractions were analyzed by high-performance liquid chromatography and negative ion electrospray ionization mass spectrometry. Double separations were performed with the same solvent system yielding 563 mg cichoric acid at 95.6% purity.

Evaluation of microstructural features of a new polymeric organic stationary phase grafted on silica surface: A paradigm of characterization of HPLC-stationary phases by a combination of suspension-state 1H NMR and solid-state 13C-CP/MAS-NMR

Silica-supported poly(octadecylacrylate) (Sil-ODA n ), polymeric octadecylsilyl silica (polymeric ODS), and monomeric octadecylsilyl silica (monomeric ODS) were studied by a combination of suspension-state 1H NMR and solid-state 13C CP/MAS-NMR to probe the mechanisms underlying their functions as stationary phases for RP-HPLC. Sil-ODA n , with a strong temperature dependent separation behaviour showed correspondent temperature dependent manifestations in both suspension-state 1H NMR and solid-state 13C CP/MAS-NMR experiments. With a gradual increase in temperature, intensity of proton signals ( 1H NMR) of octadecyl moieties (mainly methylene groups) rose dramatically. This dramatic rise was at the same temperature of an endothermic peak detectable in its DSC thermogram indicating a relatively complete solid to liquid phase transition. In addition temperature dependencies of the ratio of trans to gauche conformed well to temperature dependencies of the separation factor between naphthacene and triphenylene (as a simple indicator of shape selectivity). Therefore NMR spectra of Sil-ODA n were used as a reference for ascertaining percentage of octadecyl moieties of liquid type mobility in the two other stationary phases. Using this method we determined percentage of liquid phase in polymeric ODS and monomeric ODS at various temperatures. We suggest a combination of suspension-state 1H NMR and solid-state 13C CP/MAS-NMR for structure-dynamic characterization of various kinds of hydrocarbon chains grafted onto the silica particles.

Dioctadecyl l-glutamide-derived lipid-grafted silica as a novel organic stationary phase for RP-HPLC

Dialkyl l-glutamide-derived lipids have been found to form supramolecular assemblies and to show specific properties based on their highly ordered structures in aqueous and organic media. To use these unique properties to create molecular recognition systems, dioctadecyl l-glutamide-derived lipid-grafted porous silica particles (Sil-DSG) were newly prepared and used as a stationary phase in reversed phase liquid chromatography. Compared with conventional ODS (octadecylated silica), the Sil-DSG column showed remarkably higher selectivity for polycyclic aromatic hydrocarbons (PAHs). Especially, Sil-DSG recognized the molecular linearity and planarity of PAHs. Suspension state 1H NMR and 13C CP/MAS-NMR spectroscopies showed that the alkyl chains on the Sil-DSG are in gauche form and their mobility is strongly restricted at room temperature. This paper discusses higher selectivity of Sil-DSG with a carbonyl π-benzene π interactions.

Numerical simulation of two-phase partition chromatography in microchannels for moderated logP measurements

A finite element simulation has been used in order to study the partition chromatography process of one species between an aqueous mobile phase and an organic stationary phase located at the bottom of a rectangular microchannel. The transient model incorporates convection--diffusion of the species in the water phase coupled to the diffusion in the stationary organic phase by the way of the partition kinetics at the interface. The time evolution of the injected species concentration is analyzed versus the velocity of the mobile phase, the detecting position and the thickness of the stationary phase. The comparison of simulation results with both experimental data and analytical model confirm its validity. These simulations show that thin channels can be used to measure log P of molecules from their retention time. Finally, we have shown how the sample velocity can be optimized for a given geometry of the channel and diffusion coefficient of the species.

Mutual Metal Separation System with Enrichment Using pH‐Peak Focusing Countercurrent Chromatography

A highly efficient enrichment of metal ions was achieved by pH‐peak‐focusing high‐speed countercurrent chromatography (CCC) that is developed by the variation of the pH‐zone refining high‐speed CCC. In this method, Ca, Cd, Cu, Mg, Mn, and Zn are chromatographically extracted in a basic organic stationary phase containing ammonia and a complex‐forming reagent such as di(2‐ethylhexyl) phosphoric acid, by introducing the sample solution into the column rotated at 800–1200 rpm. When the column is eluted with the acidified mobile phase containing hydrochloric acid, metal ions are trapped and concentrated around the sharp pH border formed in between the acidic and the basic zones, moving toward the outlet of the column. Enriched metal ions are finally eluted with the sharp pH‐border as a highly concentrated peak into a small amount of eluent. The pH of the border is determined by the kinds of base and acid, and it shows the neutralization point. At this pH, trapped solute is moved towards the outlet of the column, based on its distribution ratio in each phase. The travel of this pH border through the column is determined by the molar ratio between the base in the stationary phase and acid in the mobile phase. By selecting appropriate experimental conditions, such as an acidity of the sample, bore of the column, and volume of the sample, each metal separation was achieved due to a longitudinally pH gradient on both sides of the pH border. Metal ions were concentrated at different positions in the moving pH border. When the pH border was sufficiently wide in the final stage of the elution, each concentrated metal could be separated mutually. The present method can be successfully applied to trace determination of cadmium in tap water, with coexsisting relatively large amounts of magnesium.

Stationary phases for thin-layer chromatography.

This paper presents a review of the literature concerning development of the stationary phases for thin-layer chromatography (TLC) in the last ten years. The silica gel remains the most important adsorbent for TLC separation. The kinetic properties of the silica-gel thin layer and the new TLC plates have been presented. Other materials used as stationary phase were alumina, zirconium oxide, Florisil, and ion-exchanger. Chemically new bonded stationary phase development is also discussed. The improvement of the separations of some organic mixtures by impregnation of silica gel, cellulose, or polyamide plates (with transition metal ions and silver salts) and their applications is presented. The impregnation of the thin layer with organic stationary phase and inclusion complexes is another method used for the enhancement of the separation efficiences. Another modality to improve the selectivity in TLC using ion-pairing as reagent of impregnation is described as well. The actual state of chiral separation by TLC is discussed with concrete references to recent advances in chiral stationary phases. The use of nonpolar chemically bonded stationary phases impregnated with transitional metal ions is presented as chiral stationary phases. The cellulose, modified cellulose, chitin, chitosan, and their derivatives are presented and their potential for the analysis of the racemates is discussed. The cyclodextrines and macrocyclic antibiotics were used with very good results for enantiomeric separation by TLC. A new separation approach with molecular imprinting polymers was reported as a chiral stationary phase in TLC. The examples provide a wide range of structural types that can be readily resolved enantiomerically by TLC.

Purification of Food Color Red No. 106 (acid red) using pH-zone-refining counter-current chromatography

pH-Zone-refining counter-current chromatography was successfully applied to the separation of the main components of Food Color Red No. 106 (R-106, acid red, Color Index No. 45100). A 300-mg quantity of sample was separated using the following two-phase solvent system: n-butanol–water, 40 m M sulfuric acid in organic stationary phase and 30 m M ammonia in aqueous mobile phase. The obtained fractions were analyzed by high-performance liquid chromatography and fast atom bombardment mass spectrometry. The separation yielded 261.9 mg of main component of acid red with purity of 99.9%.

Preparative separation of isomeric 2-(2-quinolinyl)-1H-indene-1,3(2H)-dione monosulfonic acids of the color additive D&C Yellow No. 10 (Quinoline Yellow) by pH-zone-refining counter-current chromatography

The main components of the color additive D&C Yellow No. 10 (Quinoline Yellow, Color Index No. 47005), 2-(2-quinolinyl)-1H-indene-1,3(2H)-dione-6′-sulfonic acid (6SA) and 2-(2-quinolinyl)-1H-indene-1,3(2H)-dione-8′-sulfonic acid (8SA), were isolated from the dye mixture by pH-zone-refining counter-current chromatography (CCC) in the ion-exchange mode. These positional isomers were separated from a portion of dye using sulfuric acid as the retainer acid and dodecylamine as the ligand (ion exchanger). The added ligand enhanced the partitioning of the hydrophilic components in the organic stationary phase of the two-phase solvent system that consisted of isoamyl alcohol–methyl tert.-butyl ether–acetonitrile–water (3:1:1:5). Thus, separation of 1.8 g of D&C Yellow No. 10 using the above method resulted in 0.6 g of 6SA and 0.18 g of 8SA of over 99% purity. The isolated compounds were characterized by mass spectrometry and proton nuclear magnetic resonance with correlated spectroscopy assignments. The study exemplifies a new field of applications for pH-zone-refining CCC, to the separation of positional isomers of strongly hydrophylic compounds containing sulfonic acid groups.

PH-Zone-refining counter-current chromatography of lappaconitine from Aconitum sinomontanum Nakai : I. Separation of prepurified extract

pH-Zone-refining counter-current chromatography was applied to the separation of diterpenoid alkaloids from a crude sample from a crude prepurified sample containing lappaconitine at about 90% purity using a multilayer coil planet centrifuge. The experiment was performed with a two-phase solvent system composed of methyl tert.-butyl ether–tetrahydrofuran–distilled water (2:2:3, v/v) where triethylamine (10 m M) was added to the upper organic stationary phase as a retainer and hydrochloric acid (10 m M) to the aqueous mobile phase as an eluter. The separation of 10.5 g of the sample yielded 9.0 g of lappaconitine at a high purity of over 99% as determined by HPLC.

ORIGINAL USES OF THE pH-ZONE REFINING PRINCIPLE: ADAPTATION TO SYNTHESIS IMPERATIVES AND TO IONIC COMPOUNDS

Countercurrent chromatography is a powerful separation technique based on the partition of solutes between two immiscible liquid phases. The first one, maintained in the column by a centrifugal force, acts as the stationary phase; the second phase, circulating through the apparatus, elutes compounds according to their partition coefficients. The total liquid nature of this process allows the addition of auxiliary components in both phases, increasing the separation power of countercurrent chromatography. In 1991, Y. Ito introduced pH-Zone refining systems in which the stationary phase contains a retainer and the mobile one an eluter. The acid-base system that acts as the retainer-eluter pair interacts with solutes and enables a separation based on acidic constant (pKa) base. First, this method was successfully used to separate and purify two poly-aza heterocyclic isomers, obtained by hetarynic dimerization and which are precursors of antitumor agents. Because of several imperatives, a new system, adapted from the classical one (eluter-retainer), was developed to respect our limitations. Secondly, ionic solutes such as sulfonic acid compounds cannot be studied by such a system, based on the influence of the acidic constant. Therefore, the retainer is replaced by a cationic liquid resin with very strong hydrophobic properties. Added to the organic stationary phase, this resin gives the stationary phase an ion-exchange behavior, guided by the eluter contained in the mobile phase. Applied to ionic solutes, the study of this new system highlights the main parameters of the separation.