Heterojunction Organic Solar Cells Research Articles

Device modeling of non-fullerene organic solar cell by incorporating CuSCN as a hole transport layer using SCAPS

Heterojunction organic solar cells with a non-fullerene acceptor (NFA-BHJ-OSC) with inorganic hole transport layer (HTL) have drawn a lot of cognizance due to their greater efficiency compared with traditional Fullerene acceptor solar cells. The most often adopted HTL, PEDOT:PSS, degrades the device, due to the hygroscopic and acidic nature of PSS. Therefore, an alternate hole transport material is necessary to optimize the output of OSCs. A simulation on the performance of NFA-BHJ-OSC with an active layer of PBDB-T/ITIC incorporated with Copper (I) thiocyanate (CuSCN) as an HTL, is performed in the present paper using the software SCAPS 1-D. CuSCN is a p-type semiconductor having wider energy band gap in comparison to other inorganic hole transport materials. In the present simulation based work, NFA-OSC having CuSCN as the hole transport layer shows the optimized PCE of 20.36%, Fill Factor (FF) of 66.88%, JSC of 33.09 mA/cm2 and VOC of 1.0341 V by varying physical parameters such as active layer thickness, temperature, and properties of HTL and ETL. These values are promising to develop NFA-OSCs incorporating CuSCN as a HTL in the near prospect.

Ladder-Type Fused Benzodithiophene Extended along the Short-Axis Direction as a New Donor Building Block for Efficient Organic Solar Cells.

Ladder-type fused aromatic systems are important core structures of small molecule acceptors for organic solar cells (OSCs). In this study, a new ladder-type donor building block, based on the benzo[1,2-b:4,5-b']dithiophene (BDT) unit where the 3,7 positions of the BDT thiophene rings and the 3' position of the thiophene rings of the vertical BDT were fused to construct a seven-ring core structure named f-DTBDT, was investigated. In the f-DTBDT structure, the fusion of the BDT core and the thiophene rings at the 4,8 positions of BDT constrains all of the aromatic rings in a coplanar structure. The newly designed f-DTBDT was successfully employed as a core donor building block and conjugated with three electron-withdrawing acceptors (2-(3-oxo-2,3-dihydro-1H-inden-1-ylidene) malononitrile (2HIC), 2-(5,6-difluoro-3-oxo-2,3-dihydro-1H-inden-1-ylidene)malononitrile (2FIC), and 2-(5,6-dichloro-3-oxo-2,3-dihydro-1H-inden-1-ylidene)malononitrile (2ClIC)) as acceptor-donor-acceptor (A-D-A)-type acceptor materials for OSCs. Characterization results showed that the three synthesized A-D-A acceptors of DTBDT-IC, DTBDT-4F, and DTBDT-4Cl have high absorption behavior in the vis-NIR region as result of an intramolecular charge transfer interaction engendered by f-DTBDT and the ending group. The absorption regions of the acceptors were complementary with that of polymer PM6. Also, the frontier orbital energy levels of the new acceptors and wide-band-gap PM6 are well matched. Bulk heterojunction OSCs were fabricated using PM6 and the acceptors, and the highest power conversion efficiency (PCE) of 10.15% was obtained when using PM6:DTBDT-4F as the active layer.

Lifetime Study of Organic Solar Cells with O-IDTBR as Non-Fullerene Acceptor

Organic solar cells (OSCs) have increased their power conversion efficiency above 18% thanks to the use of non-fullerene acceptors in binary or ternary blends or in tandem configurations. In this article, a study on the lifetime of P3HT:O-IDTBR bulk heterojunction OSCs on ITO-free flexible substrates is presented. A direct comparison of glass–glass and plastic–plastic encapsulation performance, with a special focus on its effect on the lifetime of the devices after degradation procedures, has been carried out complying with the ISOS protocols for organic photovoltaic devices. The manufactured OSCs with 1 cm2 active layer have power conversion efficiencies ranging from 1.9 to 3.4% depending on the encapsulant material, encapsulation process, and substrate. An exponential degradation rate has been found, with a similar functional behavior for glass and plastic differing in the degradation constants, which ranges from k = 0.01 to 0.002 h−1. Only in one case, the ISOS-T3 essay for plastic encapsulation, a double exponential process, was observed with degradation rates of k1 = 0.03 h−1 and a second slower process with k2 = 0.001 h−1. The longest achieved T80 lifetime is 86 h for glass-encapsulated devices under an accelerated ISOS-T3 protocol.

Effect of oligothiophene π-bridge length in D-π-A star-shaped small molecules on properties and photovoltaic performance in single-component and bulk heterojunction organic solar cells and photodetectors

Donor-acceptor molecules with thiophene fragments as the π-bridge represent a promising class of materials for organic photovoltaics especially in single-component (SC) organic solar cells (OSCs) and other related applications. However, the effect of the oligothiophene π-bridge length on physicochemical properties, photophysics, charge transport, and photovoltaic performance of these materials has not been thoroughly addressed. Here, we report on the synthesis and comprehensive investigation of the series of star-shaped donor-acceptor molecules (0T–4T) with triphenylamine as a donor core linked through an oligothiophene π-bridge of variable length to the terminal hexyl-dicyanovinyl electron-withdrawing groups. We found that variation of the π-bridge length from 0 to 4 thiophene units strongly impacts their properties such as the solubility, highest occupied molecular orbital energy, optical absorption and photophysics, film morphology, phase behavior, and molecular packing as well as the charge carrier mobility. The performance of the SC and bulk heterojunction OSCs and photodetectors is comprehensively studied and compared. The results obtained provide insight into how to fine-tune and predict properties and photovoltaic performance of small molecules for organic solar cells and photodetectors.

Effect of Thermal Annealing on the Charge Carrier Selectivity of Ultra‐Thin Organic Interface Dipoles in Silicon Organic Heterojunction Solar Cells

Interfacial layers consisting of organic molecules with a permanent dipole moment exhibit enhanced charge carrier selectivity when applied as electron‐selective contacts in crystalline silicon (c‐Si) heterojunction solar cells. It is found that thermal annealing has a detrimental effect on the charge carrier selectivity of dipole materials based on the amino acid l‐histidine mixed with a fluorosurfactant. Although, the implied open‐circuit voltage (iVoc) increases with annealing, the Voc decreases significantly which is accompanied by a decrease in the built‐in voltage (Vbi) and increase in the specific contact resistivity (ρc). Based on numerical device simulations, it is concluded that the tunneling of electrons through the dipole layer becomes less effective with increasing annealing temperature due to the decomposition of the dipole materials. The decomposition leads to a more “resistive” interfacial layer and to a gradient in the electron quasi‐Fermi potential and, thus, a decrease in Voc. Furthermore, storage under ambient air at room temperature degraded the electron‐selective contacts substantially, limiting the potential of the dipole material for the application in silicon organic heterojunction solar cells.

Improvement of the Optoelectrical Properties of a Transparent Conductive Polymer via the Introduction of ITO Nanoparticles and Its Application in Crystalline Silicon/Organic Heterojunction Solar Cells.

Compared with conventional transparent conductive indium tin oxide (ITO) films, poly(3,4-ethylenedioxythiophene):poly (styrenesulfonic acid) (PEDOT:PSS) as a conductive polymer material has been diffusely applied in organic optoelectronic devices. However, its optoelectrical properties need to be further improved. Therefore, a simple and universal approach with introducing ITO nanoparticles (NPs) was proposed to improve the optoelectrical properties of PEDOT:PSS thin films. The results show that the vertical conductivity (σDC⊥) and average transmittance (from 300 to 1200 nm) of PEDOT:PSS films were enhanced about 26.8 and 6.3%, respectively. Crystalline silicon (c-Si)/organic heterojunction solar cells (HSCs) with PEDOT:PSS/ITO NP hybrid films were fabricated and performances led to further improvement. The spatial distributions of relative electrical field intensity and the carrier generation rate of the HSCs under the standard AM 1.5 G condition were simulated, which were in good agreement with the experimental conclusions.

Pseudo-bilayer architecture enables high-performance organic solar cells with enhanced exciton diffusion length

Solution-processed organic solar cells (OSCs) are a promising candidate for next-generation photovoltaic technologies. However, the short exciton diffusion length of the bulk heterojunction active layer in OSCs strongly hampers the full potential to be realized in these bulk heterojunction OSCs. Herein, we report high-performance OSCs with a pseudo-bilayer architecture, which possesses longer exciton diffusion length benefited from higher film crystallinity. This feature ensures the synergistic advantages of efficient exciton dissociation and charge transport in OSCs with pseudo-bilayer architecture, enabling a higher power conversion efficiency (17.42%) to be achieved compared to those with bulk heterojunction architecture (16.44%) due to higher short-circuit current density and fill factor. A certified efficiency of 16.31% is also achieved for the ternary OSC with a pseudo-bilayer active layer. Our results demonstrate the excellent potential for pseudo-bilayer architecture to be used for future OSC applications.

High efficient hybrid bulk hetero junction thin-film solar cell embedded with kesterite Cu2ZnSnS4 quantum dots

The photovoltaic performance of kesterite Cu 2 ZnSnS 4 (CZTS) quantum dot (QD) incorporated poly(3-hexylthiophene-2,5-diyl) (Alvarado et al., 1998; Alvarado et al., 1998) [6,6]: phenyl-C61butyric acid hexyl ester (P3HT:PCBH) polymer matrix based organic hybrid heterojunction solar cell configuration is investigated. The inorganic filler material CZTS QDs with P3HT:PCBH matrix, forms double bulk hetero junction (BHJ) throughout in the active layer, which facilitates rapid exciton dissocitaion process at P3HT:PCBH and CZTS:PCBH interfaces that results effective charge carrier separation. The prepared active layer material has been characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), x-ray diffraction (XRD), Raman and fourier transform infra red (FTIR). The enhanced optical absorbance of prepared hybrid structure has been verified by UV–Visible analysis. It has been observed that the improvement in photo conversion efficiency (PCE) from 2.36% for the solar cell device P3HT:PCBH to 4.12% for CZTS QD based P3HT:PCBH hybrid organic solar cell device. This dramtaic increase in PCE, is mainly due to the significant enhancement in short-circuit current density (J sc ) from 7.6 mA/cm 2 to 11.2 mA/cm 2 . That suggests, the incorporation of p-type kesterite CZTS QDs into P3HT:PCBH polymer matrix enhances the effective exciton dissociation at interfaces resulting charge separation and their fast extraction to electrodes inhibiting e − /h + pair recombination. Furthermore, the hybrid solar cell shows remarkable time stability retaining 80% of original PCE measured after 30 days under ambient environment conditions. The hybrid organic solar cell device shows thermal stability by retaining 95.6% of its intial efficiency measured which has been tested in the temperature range 20–80 °C. • Photovoltaic performance of CZTS QDs:P3HT:PCBH hybrid thin film solar cell is investigated. • PCE of hybrid device has been observed to enhance from 2.36% to 4.12%. • It shows time and thermal stability retaining 80% and 95.6% efficiency.

Computational study of organic small molecules based on imidazolinone for photovoltaic applications

ABSTRACT Organic photovoltaic cells have received significant interest due to the low-cost manufacturing and compatibility to deposit on flexible substrate. However, this technology suffers from certain problems including lowest solar spectrum absorption by reason of the large band gap of donor materials. This could return to the lack of extensive studies concerning the effects of geometric structures and the energy levels associated with the synthesis of molecules. In this context, six organic π-conjugated molecules based on imidazolinone with low band gap have been studied theoretically using quantum methods namely density functional theory (DFT) and time dependent-density functional theory (TD-DFT). The highest occupied molecular orbital (HOMO), lowest unoccupied molecular orbital (LUMO), and chemicals descriptors of these molecules have been examined in this work. Spectroscopic and electronic properties have been reported in order to study the parameters which affect photovoltaic efficiency. The calculated results of these compounds show a lower HOMO energy, large absorption spectra, and good theoretical open circuit voltage. The findings of this work are helpful to enhance the performance of bulk hetero junction organic solar cells (BHJ).

In situ NMR Investigation of the Photoresponse of Perovskite Crystal

Summary Hybrid perovskites are outstanding candidates for use in optoelectronic devices. Nonetheless, hybrid perovskites present numerous fundamental issues that are not yet fully understood. This study seeks to address this problem by reporting on the occurrence of ultraslow dynamic orientation changes in the methylammonium (MA) cations and the corresponding changes in the inorganic lattice of MAPbI3 perovskite crystals occurring over a time scale of 100 s under continuous illumination based on in situ single-crystal 2H nuclear magnetic resonance and in situ X-ray diffraction results. The demonstrated ultraslow dynamic changes in MAPbI3 are far slower than elementary molecular motions typically having time scales of femtoseconds and picoseconds and have never been reported previously. The ultraslow dynamic changes have been correlated with the reduction of band gap and the increase of absorption coefficient of MAPbI3, providing the molecular origins of the stabilization process in the photoresponse of the MAPbI3 device.

Comprehensive and Comparative Analysis of Photoinduced Charge Generation, Recombination Kinetics, and Energy Losses in Fullerene and Nonfullerene Acceptor-Based Organic Solar Cells.

In this work, a unique comprehensive and comparative analysis of photoinduced charge generation, recombination kinetics, and energy losses has been carried out to study the effect of different fullerene-based acceptors (FBAs) and nonfullerene acceptors (NFAs) on the performance of organic solar cells (OSCs). For this, different FBAs, specifically ICBA, PC60BM, and PC70BM, and NFAs, namely, ITIC, IT-4F, and IEICO-4F, were employed independently along with a particular donor polymer, PBDB-T, to fabricate bulk heterojunction OSCs and their performances have been compared. This donor molecule is known to give similar power conversion efficiency (PCE) with FBAs and NFAs and hence is ideal for comparative studies. The origin of the higher PCE of NFA-based OSCs vs FBA-based OSCs is analyzed in terms of spectral coverage, charge generation, recombination, and energy loss. It is found that the energy loss (ΔEloss) is ∼0.8 to 1 eV for FBA-based OSCs, while it is 0.5-0.7 eV for NFA-based OSCs. Interestingly, for the PBDB-T:IEICO-4F-based system, energy losses due to charge generation (ΔECT) are ∼0 eV and therefore this system has minimum ΔEloss among all of the studied devices. Providing a systematic, comprehensive, and comparative outlook, our study may further be extended to new upcoming NFA systems and beyond the donor system used in this work.

Optical Absorption Enhancement in Polymer BHJ thin Film Using Ag Nanostructures: A Simulation Study

Background: The photo-absorption and light trapping through the different layers of the organic solar cell structures are a growing concern now-a-days as it affects dramatically the overall efficiency of the cells. In fact, selecting the right material combination is a key factor in increasing the efficiency in the layers. In addition to good absorption properties, insertion of nanostructures has been proved in recent researches to affect significantly the light trapping inside the organic solar cell. All these factors are determined to expand the absorption spectrum and tailor it to a wider spectrum. Objective: The purpose of this investigation is to explore the consequence of the incorporation of the Ag nanostructures, with different sizes and structures, on the photo absorption of the organic BHJ thin films. Methods: Through a three-dimensional Maxwell solver software, Lumerical FDTD, a simulation and comparison of the optical absorption of the three famous organic materials blends poly(3- hexylthiophene): phenyl C71 butyric acid methyl ester (P3HT:PCBM), poly[N-9″-heptadecanyl-2,7- carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)]: phenyl C71 butyric acid methyl ester (PCDTBT:PCBM) and poly[2,6-(4,4-bis-(2-ethylhexyl)-4H-cyclopenta[2,1-b;3,4-b′]dithiophene)-alt- 4,7-(2,1,3-benzothiadiazole)]: phenyl C71 butyric acid methyl ester (PCDPDTBT:PCBM) has been conducted. Furthermore, FDTD simulation study of the incorporation of nanoparticles structures with different sizes, in different locations and concentrations through a bulk heterojunction organic solar cell structure has also been performed. Results: It has been demonstrated that embedding nanostructures in different locations of the cell, specifically in the active layer and the hole transporting layer had a considerable effect of widening the absorption spectrum and increasing the short circuit current. The effect of incorporation the nanostructures in the active layer has been proved to be greater than in the HTL. Furthermore, the comparison results showed that, PCDTBT:PCBM is no more advantageous over P3HT:PCBM and PCPDTBT:PCBM, and P3HT:PCBM took the lead and showed better performance in terms of absorption spectrum and short circuit current value. Conclusion: This work revealed the significant effect of size, location and concentration of the Ag nanostructures while incorporated in the organic solar cell. In fact, embedding nanostructures in the solar cell widen the absorption spectrum and increases the short circuit current, this result has been proven to be significant only when the nanostructures are inserted in the active layer following specific dimensions and structures.

Star-shaped benzotriindole-based donor-acceptor molecules: Synthesis, properties and application in bulk heterojunction and single-material organic solar cells

The search of the novel building blocks for π-conjugated donor-acceptor (D-π-A) molecules remains an urgent task to design promising materials for organic solar cells (OSCs) and other electronic devices. Here we report on the design and synthesis of two star-shaped D-π-A small molecules based on benzotriidole (BTI) electron-donating core, BTI(2T-DCV-Hex)3 and BTI(2T-CNA-EHex)3, end-capped with either hexyldicyanovinyl or 2-ethylhexylcyanoacetate acceptor groups. Comprehensive investigation and comparison of the optical, thermal and physicochemical properties of these molecules and their analogue with the triphenylamine (TPA) core, N(Ph-2T-DCV-Hex)3, revealed the effect of the electron-withdrawing groups and type of the donor core on their properties. The BTI-based material BTI(2T-DCV-Hex)3 differs from the amorphous TPA-based analogue by high crystallinity and blue-shifted absorption and luminescence spectra. The change of electron-withdrawing group from hexyldicyanovinyl to 2-ethylhexylcyanoacetate leads to a higher energy of the lowest unoccupied molecular orbital, lower solubility and several times higher photoluminescence quantum yield in solutions achieving 67%. Evaluation of the photovoltaic performance of these materials in single-material OSCs and as a donor material in bulk heterojunction OSCs with PC71BM as an acceptor revealed that the devices based on BTI(2T-DCV-Hex)3 are more efficient as compared to those based on BTI(2T-CNA-EHex)3. In comparison to N(Ph-2T-DCV-Hex)3, the photovoltaic devices based on BTI(2T-DCV-Hex)3 showed the comparable performance in bulk heterojunction OSCs and two times higher performance (about 1%) in single-material OSCs. As a result, we conclude that the BTI core is a promising block for the design of semiconducting materials for organic photovoltaics and other related applications.

Highly Efficient Inorganic–Organic Heterojunction Solar Cells Based on Polymer and CdX (X = Se, Te) Quantum Dots: An Insight from a Theoretical Study

By using the density functional method, we explore the potentiality of recently synthesized CdX (X=Se, Te)QD/P3HT composites in solar energy conversion devices. Our study reveals that inorganic/org...

Delocalization boosts charge separation in organic solar cells

Organic solar cells (OSCs) utilizing π-conjugated polymers have attracted widespread interest over the past three decades because of their potential advantages, including low weight, thin film flexibility, and low-cost manufacturing. However, their power conversion efficiency (PCE) has been far below that of inorganic analogs. Geminate recombination of charge transfer excitons is a major loss process in OSCs. This paper reviews our recent progress in using transient absorption spectroscopy to understand geminate recombination in bulk heterojunction OSCs, including the impact of polymer crystallinity on charge generation and dissociation mechanisms in nonfullerene acceptor-based OSCs. The first example of a high PCE with a small photon energy loss is also presented. The importance of delocalization of the charge wave function to suppress geminate recombination is highlighted by this focus review. When light is shined on semiconducting polymers, singlet excitons are promptly generated in organic solar cells. At a donor–acceptor heterojunction, excitons separate into holes on the donor and electrons on the acceptor as a result of the energetic offset of the molecular orbital. If the electron and hole separate further, they become free from Coulombic attraction and hence survive up to nano- or microseconds, long enough to be transported to each electrode. Otherwise, the geminate electron–hole pairs are likely to recombine to the ground state.

Three-Dimensional Spirothienoquinoline-Based Small Molecules for Organic Photovoltaic and Organic Resistive Memory Applications.

A new electron-rich spirothienoquinoline unit, tBuSAF-Th, has been developed via incorporation of a thienyl unit instead of a phenyl unit into the six-membered ring of the spiroacridine (SAF) and utilized for the first time as a building block for constructing small-molecule electron donors in organic solar cells (OSCs) and as active layers in organic resistive memory devices. The resulting three-dimensional spirothienoquinoline-containing 1-4 exhibit high-lying highest occupied molecular orbital (HOMO) energy levels. By the introduction of electron-deficient benzochalcogenodiazole linkers, with the chalcogen atoms being varied from O to S and Se, a progressively lower lowest unoccupied molecular orbital (LUMO) energy level has been achieved while keeping the HOMO energy levels similar. This strategy has allowed an enhanced light-harvesting ability without compromising open-circuit voltage (Voc) in vacuum-deposited bulk heterojunction OSCs using 1-4 as donors and C70 as the acceptor. Good photovoltaic performances with power conversion efficiencies (PCEs) of up to 3.86% and high short-circuit current densities (Jsc) of up to 10.84 mA cm-2 have been achieved. In addition, organic resistive memory devices fabricated with these donor-acceptor small molecules exhibit binary logic memory behaviors with long retention times and high on/off current ratios. This work indicates that the spirothienoquinoline moiety is a potential building block for constructing multifunctional organic electronic materials.

Investigation of post-thermal annealing-induced enhancement in photovoltaic performance for squaraine-based organic solar cells

In this work, we have systematically investigated the post-thermal annealing-induced enhancement in photovoltaic performance of a 2,4-bis[4-(N, N-diisobutylamino)-2,6-dihydroxyphenyl] squaraine (DIBSQ)/C60 planar heterojunction (PHJ) organic solar cells (OSCs). An increased power conversion efficiency (PCE) of 3.28% has been realized from a DIBSQ/C60 device with thermal annealing at 100 °C for 4 min, which is about 33% enhancement compared with that of the as-cast device. The improvement of the device performance may be mainly ascribed to the crystallinity of the DIBSQ film with post-thermal annealing, which will change the DIBSQ donor and C60 acceptor interface from ^PHJ to hybrid planar-mixed heterojunction. This new donor-acceptor heterojunction structure will significantly improve the charge separation and charge collection efficiency, as well as the open circuit voltage (Voc) of the device, leading to an enhanced PCE. This work provides an effective strategy to improve the photovoltaic performance of SQ-based OSCs.

Conjugated Polymers as Hole Transporting Materials for Solar Cells

In principle, conjugated polymers can work as electron donors and thus as low-cost p-type organic semiconductors to transport holes in photovoltaic devices. With the booming interests in high-efficiency and low-cost solar cells to tackle global climate change and energy shortage, hole transporting materials (HTMs) based on conjugated polymers have received increasing attention in the past decade. In this perspective, recent advances in HTMs for a range of photovoltaic devices including dye-sensitized solar cells (DSSCs), perovskite solar cells (PSCs), and silicon (Si)/organic heterojunction solar cells (HSCs) are summarized and perspectives on their future development are also presented.

Impact of concentration variation and thermal annealing on performance of multilayer OSC consisting of sandwiched P3HT layer between PEDOT:PSS and P3HT:PCBM

In this paper, comprehensive study on variation in composition ratio and thermal annealing of multilayer organic solar cells (OSC) has been demonstrated. Our previous work reported that in comparison to the conventional OSC structure, multilayer OSC consisting of the pure donor phase between the hole transport layer and active layer has shown a significant improvement in the power conversion efficiency (PCE). Since photovoltaic performance of the OSC strongly influenced by composition ratio, the impact of poly 3-hexylthiophene (P3HT) and 6,6-phenyl-C61-butyric acid methyl ester (PCBM) weight ratio has been analyzed. It has been found that, the short-circuit current density (JSC) of the device is highest for the P3HT:PCBM composition ratio of 1.0:0.8 and decreases slightly for 1.0:1.0 weight ratio. This study has also been accompanied with the thermal annealing on spin coated P3HT:PCBM which further enhances the PCE of the device. The maximum JSC and the PCE of 9.47 mA/cm2 and 3.26% has been achieved for the multilayer OSC having P3HT:PCBM composition ratio of 1.0:0.8 and thermally annealed at 140 °C. This is attributed largely by the tuned phase morphology of the donor-acceptor. It has been found that, the P3HT:PCBM weight ratio of 1.0:0.8 results into efficient photon absorption and charge separation in the bulk heterojunction OSC. The reduced concentration of PCBM in 1.0:0.8 weight ratio leads to the strong interchain interaction of P3HT molecules which enhances the charge separation and collection ability of the bulk heterojunction OSC.

Dialkoxymethano[60]fullerenes as electron acceptors in thin-film organic solar cells

This study presents the synthesis, characterization, and electrochemical properties of four new dialkoxymethanofullerenes, as well as their performance in organic solar cells (OSCs) devices. Dialkoxymethanofullerenes were synthesized in 27%–32% yield by thermolysis of dialkoxyoxadiazolines and reaction with C60 under reflux in toluene. The prepared compounds were then characterized and used for the first time as electron-acceptor materials in thin-film bulk heterojunction OSCs with PBTZT-stat-BDTT-8 as the electron donor material. The devices made with ethoxy-hexyloxymethanofullerene and methoxy-hexyloxymethanofullerene exhibited optimal power conversion efficiencies (PCEs) of 3.79% and 4.65%, with open-circuit voltage of 0.832 and 0.831 V, respectively. In contrast, the devices made with ethoxy-ethoxymethanofullerene and methoxy-ethoxymethanofullerene exhibited very low PCEs of <0.01% for both, indicating a large impact of the substituents on device performance.