Organic Dyes Research Articles

Solar-powered detection of organic dyes using nitrogen-doped N-TiO2/Ag2O nanorod arrays.

Organic pollutant detection has caused widespread concern regarding due to their potential environmental and human health risks. In this work, a nitrogen-doped titanium dioxide/silver oxide (N-TiO2/Ag2O) composite has been designed asa sensitive photoelectrochemical (PEC) monitoring platform of organic dyes. Sensitive determination relies on the outstanding PEC performance of N-TiO2/Ag2O. The improved PEC performance stems from the effective separation of photocarriers and the extended light response range provided by the narrowing bandgap and a p-n junction with N-TiO2/Ag2O. The N-TiO2/Ag2O electrode exhibits a photocurrent density of up to 2.2mA/cm2, demonstrating three times increase compared withthe photocurrent density observed with the pure TiO2 film. The linear detection range for rhodamine B (RhB), methylene blue (MB), and methyl orange (MO) is 0.2ng/mL to 10 μg/mL with an ultrasensitive detection limit of 0.2ng/mL without bias voltage. Due to the outstanding photocurrent density and sensitive response to organic pollutants, the N-TiO2/Ag2O PEC sensor provided a promising analytical method to detect environmental organic dyes.

Eco-Friendly Synthesis of CuO@ZnO Nanocomposites Using Artemisia vulgaris Leaf Extract and Study of Its Photocatalytic Activity for Methylene Blue

In this study, copper oxide nanoparticles (CuO NPs), zinc oxide nanoparticles (ZnO NPs), and copper oxide/zinc oxide nanocomposites (CuO@ZnO NPs) were synthesized by green synthetic route where bioactive compounds inherently present in the leaf extract of Artemisia vulgaris act as stabilizing and reducing agents. Phytochemicals present in leaf extract were assessed by qualitative chemical tests and spectroscopic measurements. UV-visible spectroscopy, Fourier Transform Infrared (FTIR) spectroscopy, Energy Dispersive X-ray (EDX) spectroscopy, X-ray Diffraction (XRD), and Field Emission Scanning Electron Microscopy (FESEM) were used to characterize the as-synthesized nanomaterials, i.e., CuO, ZnO, and CuO@ZnO NPs. XRD pattern revealed the crystalline nature of nanoparticles. Based on the Debye–Scherrer formula, the sizes of CuO NPs, ZnO NPs, and CuO@ZnO NCs were found to be 17.24, 20.74, and 22.50 nm, respectively. The band gap of the as-prepared nanomaterials was measured using the Tauc plot. Using the nanomaterials, MB degradation was studied at room temperature under exposure to UV light. The degradation efficiency of CuO, ZnO, and 2% CuO@ZnO was found to be 52%, 68%, and 98%, respectively. Kinetic degradation process reveals that the CuO@ZnO NCs showed a better photocatalytic activity on MB dye with the degradation constant of 0.04124 min−1 compared to those of either constituent. Based on the findings, it was found that CuO@ZnO nanocomposites have the potential to degrade MB as an organic dye and can be used for wastewater treatment.

Improvement photoresponsivity and quantum efficiency of photodetector sensitized by organic dye

Improvement photoresponsivity and quantum efficiency of photodetector sensitized by organic dye

Fabrication of mesoporous titania films and kinetics of photoelectrocatalytic degradation of organic dye

Mesoporous titania films with worm-like patterns were fabricated on indium-tin oxide (ITO) glass by dip-coating skill, and were characterized systematically. Impacts of the process and technical parameters on the formation of the films were investigated. The mesoporous films were characterized by low-angle X-ray diffraction (XRD) and wide-angle XRD, transmission electron microscopy (TEM), scanning electron microscope (SEM), linear sweep voltammograms and nitrogen adsorption/desorption isotherms. Subsequently, the films were used in a photoelectrocatalytic system for the degradation of methyl orange. The influence of operation variables, including pH values, bias potential, light intensity, organics concentration and the mass of the films, on the degradation of the dye was investigated in details. More than 96 % degradation of the organics was achieved in 2 h. The kinetic results for the photoelectrocatalytic oxidation of the organic were also presented in this paper.

Photocatalytic degradation of methylene blue over MIL-100(Fe)/GO composites: a performance and kinetic study

Adsorption coupled with photocatalytic degradation is proposed to fulfill the removal and thorough elimination of organic dyes. Herein, we report a facile hydrothermal synthesis of MIL-100(Fe)/GO photocatalysts. The adsorption and photocatalytic degradation process of methylene blue (MB) on MIL‐100(Fe)/GO composites were systematically studied from performance and kinetic perspectives. A possible adsorption‐photocatalytic degradation mechanism is proposed. The optimized 1M8G composite achieves 95% MB removal (60.8 mg/g) in 210 min and displays well recyclability over ten cycles. The obtained MB adsorption and degradation results are well fitted onto Langmuir isotherm and pseudo‐second order kinetic model. This study shed light on the design of MOFs based composites for water treatment.Graphical

Robust Photocatalytic MICROSCAFS® with Interconnected Macropores for Sustainable Solar-Driven Water Purification.

Advanced oxidation processes, including photocatalysis, have been proven effective at organic dye degradation. Tailored porous materials with regulated pore size, shape, and morphology offer a sustainable solution to the water pollution problem by acting as support materials to grafted photocatalytic nanoparticles (NPs). This research investigated the influence of pore and particle sizes of photocatalytic MICROSCAFS® on the degradation of methyl orange (MO) in aqueous solution (10 mg/L). Photocatalytic MICROSCAFS® are made of binder-less supported P25 TiO2 NPs within MICROSCAFS®, which are silica-titania microspheres with a controlled size and interconnected macroporosity, synthesized by an adapted sol-gel method that involves a polymerization-induced phase separation process. Photocatalytic experiments were performed both in batch and flow reactors, with this latter one targeting a proof of concept for continuous transformation processes and real-life conditions. Photocatalytic degradation of 87% in 2 h (batch) was achieved, using a calibrated solar light simulator (1 sun) and a photocatalyst/pollutant mass ratio of 23. This study introduces a novel flow kinetic model which provides the modeling and simulation of the photocatalytic MICROSCAFS® performance. A scavenger study was performed, enabling an in-depth mechanistic understanding. Finally, the transformation products resulting from the MO photocatalytic degradation were elucidated by high-resolution mass spectrometry experiments and subjected to an in silico toxicity assessment.

Photocatalytic degradation of Rhodamine B dye via Bi2O3 embedded BaO-P2O5-TeO2 glass nanocomposites: An ab initio study of structural, optical, and electrical transport properties

Bismuth incorporated glassy systems with composition xBi2O3-(1-x) [0.3BaO-0.3P2O5-0.4TeO2] (where x = 0.10, 0.15, 0.20, and 0.25) are synthesized by melt quenching technique. The glassy systems are examined for their structural, and surface morphological properties using XRD, SEM, and EDX analysis. A study of photocatalytic activity for the degradation of common organic dyes like Rhodamine B (RhB) dye under visible light is also carried out. From UV-vis absorbance data, the calculated optical band gap energy values declined from (2.99-2.56) eV, whereas the Urbach energy and refractive index values increased from (0.35 -0.52) eV, and (2.39 - 2.52), respectively with the rise of Bi2O3 content(x). Additionally, the fundamental processes of electrical conductivity have been studied within the framework of Jonscher's universal power law and the Almond-West formalism. The Mott and Greaves model asserts that the small polaron hopping model underlies DC conductivity; as Bi2O3 content increases, DC conductivity rises, but hopping distance (Rhop) and hopping energy (Whop) drop dramatically. The electrical conductivity study reveals the semi-conducting nature of the as-prepared samples. In our present study, we are focusing on the structural, optical, and electrical transportation properties, additionally, we investigated this class of glassy materials as a promising candidate for photocatalytic dye degradation. Our study reveals that RhB dye can degrade up to 75% within 340 min of visible light illumination. Moreover, the test demonstrates the production of superoxide radicals by the CB-electrons and hydroxyl radicals by the VB holes enables efficient photocatalytic dye degradation.

Facile one-step synthesis of in situ WO3@Gr nanorods as an efficient material for antimicrobial and decoloration applications

This work examined the synthesis, antibacterial activity, and decolourisation of WO3@Graphene nanorods (WO3@Gr NR). WO3@Gr NR nanocomposite was in situ produced via a facile one-step hydrothermal process employing sodium tungstate dihydrate and exfoliated graphene as precursors. The resulted NR exhibited an average diameter of 13 nm, a large specific surface area of 53.3 m2 g−1, and a bimodal pore size distribution with an average pore size of 5.5 nm. The optical bandgap is extrapolated to be 2.75 eV. Graphene was shown to be responsible for the sample’s elaborate visible-light absorption, which improved adsorption and the ability to harvest visible light. WO3@Gr NR are more efficient against E. coli than S. aureus, killing up to 52% and 39% of cells, respectively, after two hours of treatment. When used in conjunction with invisible light, the NR killed E. coli and S. aureus by 78 and 62%, respectively. The bactericidal activity of photoinduced WO3@Gr NR was evaluated against P. aerugunosa, E. faecalis, E. coli, and S. aureus. The photocatalytic constant rates of organic dye methylene blue (MB) were determined to be 0.01 min−1. An IC50 (50% cell growth inhibition) value of 97 (μg ml−1) was determined for the nanocomposite against human liver cancer cell lines (HepG2). Our findings suggest that this nanorod may be utilised to degrade bacteria and organic colours in wastewater simultaneously while posing no risk to human health.

Tuning the interlayer spacing of graphene oxide membrane via surfactant intercalation for ultrafast nanofiltration

A facile method has been developed to fabricate lamellar composite graphene oxide (CGO) membranes by incorporating positively charged surfactants – cetyltrimethylammonium bromide (CTAB). The interlayer spacing of GO nanosheets was regulated by the sum of both vertical and horizontal alignment of CTAB on the GO surface via electrostatic interaction. The CTAB intercalated GO membrane exhibited an internal layer spacing of 16.97 Å compared to 8.26 Å for the GO membrane. The obtained CGO lamellar membrane with well-defined nanochannels showed ultrafast pure water flux of ∼1112 L h−1 m−2 bar−1 and an excellent separation efficiency of >99 % towards negatively charged organic dye molecules at a high permeation flux of ∼932 L h−1 m−2 bar−1, which was nearly 2.5-fold enhancement compared with that of the pristine GO membrane (∼400 L h−1 m−2 bar−1). The electrostatic and π–π interaction forces between the CGO membrane and organic dye molecules played a major role in the overall dye separation mechanism. Furthermore, the CGO membrane demonstrated excellent stability with no loss in separation performance (>96 % organic molecules rejection) after exposure to various pH solutions and deionized water (DI) water. The current work provides a straightforward approach for the formation of highly tunable and stable CTAB-intercalated GO membranes for ultrafast molecular separation.

Ultrasonication-assisted synthesis of transition metal carbide of MXene: an efficient and promising material for photocatalytic organic dyes degradation of rhodamine B and methylene blue in wastewater.

Water pollutants of non-biodegradable toxic aromatic dye including Methylene blue (MB) and Rhodamine (RhB) are extremely carcinogenic thiazines used in various industries such asleather industry, paper industry, and the dyeing industry. The presence of dyes in wastewater causes severe threats to human health that are responsible for various harmful chronic or acute diseases and also shows an adverse impact on the environment as it reduces transparency and is harmful to water microorganisms. To overcome severe issues, many traditional techniques have been used to remove toxic pollutants, but thesemethods are insufficient to remove chemically stable dyes that remain in the treated wastewater. However, the photocatalytic degradation process is an efficient approach to degrade the dye up to the maximum extent with improved efficiency. Therefore, in this work, a new class of two-dimensional (2D) transition metal carbide of Titanium Carbide (Ti3C2Tx) MXene material was used for the organic dyes degradation such as MB and RhB using a photocatalytic process. A layered structure of hexagonal lattice symmetry of Ti3C2Tx MXene was successfully synthesized from the Titanium Aluminum Carbide ofTi3AlC2 bulk phase using an exfoliation process. Further, the XRD spectrum confirms the transformation of bulk MAX phase having (002) plane at 9.2° to Ti3C2Tx MXene of (002) plane at 8.88° confirms the successful removal of Al layer from MAX phase. A smooth, transparent, thin sheet-like morphology of Ti3C2Txnanosheet sizewere found to be in the range of 70 to 150nm evaluated fromTEM images. Also,no holes or damages in the thin sheets were foundafter the treatment with strong hydrofluoric acid confirms the formationTi3C2Tx layered sheets. The synthesized Ti3C2Tx MXene possesses excellent photocatalytic activity for the degradation of dyes MB, RhB, and mixtures of MB and RhB dyes. MB dye degraded with a degradation percentage efficiency of 99.32% in 30min, while RhB dye was degraded upto98.9% in 30min. Also, experiments were conducted for degradation ofmixture of MB and RhB dyes by UV light, and the degradationpercentage efficiency were found to be 98.9% and 99.75% for mixture of MB and RhB dyein 45min, respectively. Moreover, reaction rate constant (k) was determined for each dye of MB, RhB, and mixtures of MB and RhB and was found to be 0.0215min-1 and 0.0058min-1, and for mixtures, it was 0.0020min-1 and 0.009min-1, respectively.

Crystal violet degradation by visible light-driven AgNP/TiO2 hybrid photocatalyst tracked by SERRS spectroscopy

Dyes are important concerns regarding aquatic environmental contamination given their extensive industrial use and the occurrence of highly toxic and carcinogenic effects on the biota. In this work, photodegradation processes of the organic dye crystal violet (CV) by a hybrid plasmonic photocatalyst involving titanium dioxide (TiO2) and silver nanoparticles (AgNP), through irradiation with low-power visible light were studied, and the experiments were tracked by ultraviolet-visible absorption (UV–VIS) and surface-enhanced resonance Raman scattering (SERRS) spectroscopies. Enhanced photocatalytic activity was observed, reaching about 71, 80 and 87 % of CV removal with only 100 minutes of irradiation, depending on the Ag loading used. The high photocatalytic efficiency is further highlighted by the low energy consumption in the process, requiring only ca. 1.46 kW h L-1 in the best reaction condition. Quantum-mechanical calculations were used to the assignment of electronic spectra, as well as to the prediction of frontier molecular orbitals and atomic charges, aiming to propose mechanisms for radical attacks. Such results allow suggesting degradation processes involved mainly N-demethylation and bond breaking of central carbon. The presence of CV protonated species was also supported through Density Functional Theory (DFT) investigation. The integration of theoretical and experimental results allows proposing the formation of pararosaniline, phenol and benzophenone derivatives, which may have highest ecotoxicity than the original contaminant, outstanding the remarkable relevance of SERRS spectroscopy in monitoring such recalcitrant substances.

Polyester fabric supported graphene oxide/Cu-Ag bimetallic nanoparticles as a "dip catalyst" for the reduction of p-nitrophenol and organic dyes

In this paper, we present a new catalyst based on graphene oxide deposited on PES fabric and decorated with Cu0 and Ag0 NPs. The material was created via dip-coating followed by in-situ reduction of Cu2+ and Ag+ to Cu0 and Ag0 on its surface. Different physico-chemical characterizations were performed to investigate the possible interfacial interactions between PES, GO, and metallic ions. The PES-GO/Cu0-Ag0 was evaluated for the reduction of 4-nitrophenol (0.03. 10-3 M), Rhodamine B (20 ppm) and Methyl Orange (20 ppm). The PES-GO/Cu0-Ag0 catalyst shows outstanding catalytic activity for the reduction of all organic compounds tested. The reaction constant for 4-NP, RhB, and MO was 0.564, 0.569, and 0.42 min-1, respectively. Furthermore, the findings indicate that PES-GO/Cu0-Ag0 coatings on PES substrate may be advantageous to avoid problems with powder separation.

A switchable zinc-based metal organic framework for the light triggered absorption and release of organic dyes

Due to its adjustable pore structure, the metal–organic frameworks (MOFs) have attracted much attention in the treatment of organic dye molecules in wastewater. However, the general tuning of the pore channels of MOFs is mainly by changing the chain length of the organic ligands and metal nodes. This approach not only limits the types of MOFs, but also limits the treatment of a large number of dye methylene blue (MB) and methyl orange (MO) dye molecules in the wastewater. Hence, we synthesized photoresponsive Zn-AzDC/TPA MOF as adsorbents to adsorb and release organic dye molecules in a photo-controlled manner. The photoresponsive Zn-AzDC/TPA was prepared using a mixed ligand strategy, in which the azobenzene carboxylic acid derivative (AzDC) served as a photoresponsive ligand and terephthalic acid (TPA) served as a non-active ligand in coordination with zinc ion. The optical and structural properties of the synthesized Zn-AzDC/TPA was characterized by UV–vis, FT-IR, PXRD, SEM, TEM, TGA, and pore analysis. Interestingly, it was found that the photoresponsive AzDC unit of Zn-AzDC/TPA demonstrated reversible trans–cis isomerization under the alternating UV and visible light, resulting in reversible changes in the pore size of the Zn-AzDC/TPA. Its photoresponse properties can trapp and release dye molecules under light-driven conditions. This result provides a new direction for the application of photoresponsive MOF and also lays a foundation for the study of diversified optically responsive materials.

N-heterocyclic carbene functionalized boehmite-supported silver nanoparticles as nanocatalyst for reduction of environmental pollutants

The drastic change in the industrial sector and the commercialization has led to the exposure of various hazardous molecules in the atmosphere wherein modern catalytic techniques have played a crucial role in the advancement of technologies to overcome this problem. In this work, we have reported an efficient method for the synthetic fabrication of novel N-heterocyclic carbene functionalized boehmite-supported silver nanoparticles (BML@Ag) as a sustainable nanocatalyst for treating water pollutants like 4-nitrophenol (4-NP) and Congo red (CR) dye. Further, to confirm the successful development of the prepared nanocatalyst we have carried out various spectroscopic and microscopic analyses like FT-IR, p-XRD, FE-SEM, EDS, HR-TEM, BET and TGA. The average crystallite size was found to be 6.69 nm. Further, the BML@Ag nanocatalyst was explored for its catalytic efficacy in the reduction of 4-NP and degradation of the organic diazo dye CR using an aqueous solution of NaBH4 as the reducing agent. The reduction of 4-NP was observed to occur in 2.5 min (99.9%), while CR degraded in 5 min (98.8%), with the rate constants of 36.2×10-3 and 13.6×10-3 s-1 respectively. The recyclability study was demonstrated for both 4-NP and CR dye and recyclability was achieved up to 3 cycles with an excellent conversion efficiency. To explore the convenience of the BML@Ag nanocatalyst, the effects of changing parameters such as catalyst loading, pH, and salt concentration were thoroughly investigated. Furthermore, the ability of the BML@Ag nanocatalyst to reduce/degrade the pollutants was demonstrated with spiked tap and lake water samples. The efficiency of BML@Ag nanocatalyst was found to give the best conversion efficiency for the lake water samples of both 4-NP and CR dye with 99.5% and in the tap water the efficiency was noted to be reduced in both cases. The real-time investigation validated the competence of the BML@Ag nanocatalyst to be extended for commercial use.

3-aminopropyltriethoxysilane modified MXene on three-dimensional nonwoven fiber substrates for low-cost, stable, and efficient solar-driven interfacial evaporation desalination

Recently, the solar-driven interfacial evaporation desalination has attracted more and more attentions due to the advantages of low cost, zero energy consumption, and high water purification rate, etc. One of the bottlenecks of this emerging technique lies in a lack of simple and low-cost ways to construct three-dimensional (3D) hierarchical microstructures for photothermal membranes. To this end, a two-step strategy is carried out by combining surface functionalization with substrate engineering. Firstly, a silane coupling agent 3-aminopropyltriethoxysilane (APTES) is grafted onto an ideal photothermal material of Ti3C2Tx MXene, to improve the nanochannel sizes and hydrophilicity, which are attributed to enlarged interspaces of MXene and introduced hydrophilic group e.g., –NH2 and –OH, respectively. Secondly, a low-cost and robust nonwoven fiber (NWF) substrate, which has a 3D micron-sized mesh structure with interlaced fiber stacks, is employed as the skeleton to load enough APTES-grafted MXene by a simple soaking method. Benefited from above design, the Ti3C2Tx-APTES/NWF composite membrane with a 3D hierarchical structure shows enhanced light scattering and utilization, water transport and vapor escape. A remarkable evaporation rate of 1.457 kg m−2 h−1 and an evaporation efficiency of 91.48 % are attained for a large-area (5 × 5 cm2) evaporator, and the evaporation rate is further increased to 1.672 kg m−2 h−1 for a small-area (2 × 2 cm2) device. The rejection rates of salt ions and heavy metal ions are higher than 99 % and 99.99 %, respectively, and the removal rates of organic dye molecules are nearly to 100 %. Besides, the composite photothermal membrane exhibits great stabilities in harsh conditions such as high salinities, long cycling, large light intensities, strong acid/alkali environments, and mechanical bending. Most importantly, the photothermal membrane shows a considerable cost-effectiveness of 89.4 g h−1/$. Hence, this study might promote the commercialization of solar-driven interfacial evaporation desalination by collaboratively considering surface modification and substrate engineering for MXene.

Photocatalytic performance of ZnO and ZnO/Zn3(PO4)2 coatings formed by plasma electrolytic oxidation of zinc

In this study, plasma electrolytic oxidation (PEO) of zinc in a water solution containing 10 g/L Na3PO4⋅12H2O + 2 g/L KOH, was used for the preparation oxide of coatings for application in photocatalysis for degradation of organic dyes. Degradation of methyl orange (MO) as a model of organic dyes under simulated sunlight was used. In coating formed after 2 min of PEO, the pure phase hexagonal wurtzite ZnO was identified, while in coatings formed for a long time of PEO (up to 5 min) monoclinic phase of Zn3(PO4)2 was identified together with ZnO (ZnO/Zn3(PO4)2 coatings). ZnO/Zn3(PO4)2coatings show better photocatalytic activity (PA) than ZnO coating. The ZnO/Zn3(PO4)2 coating with the highest PA was formed after 4 min. Coupling ZnO with Zn3(PO4)2 reduce the recombination rate of photo-generated electron/hole pairs in ZnO which leads to an increase in PA of ZnO/Zn3(PO4) coatings compared to pure ZnO coating. This is confirmed by photoluminescent measurements. According to photocatalytic and photoluminescence measurement mechanism of the light-induced degradation of MO over ZnO/Zn3(PO4)2 coatings is suggested.

Correlating semiconductor nanoparticle architecture and applicability for the controlled encoding of luminescent polymer microparticles

Luminophore stained micro- and nanobeads made from organic polymers like polystyrene (PS) are broadly used in the life and material sciences as luminescent reporters, for bead-based assays, sensor arrays, printable barcodes, security inks, and the calibration of fluorescence microscopes and flow cytometers. Initially mostly prepared with organic dyes, meanwhile luminescent core/shell nanoparticles (NPs) like spherical semiconductor quantum dots (QDs) are increasingly employed for bead encoding. This is related to their narrower emission spectra, tuneability of emission color, broad wavelength excitability, and better photostability. However, correlations between particle architecture, morphology, and photoluminescence (PL) of the luminescent nanocrystals used for encoding and the optical properties of the NP-stained beads have been rarely explored. This encouraged us to perform a screening study on the incorporation of different types of luminescent core/shell semiconductor nanocrystals into polymer microparticles (PMPs) by a radical-induced polymerization reaction. Nanocrystals explored include CdSe/CdS QDs of varying CdS shell thickness, a CdSe/ZnS core/shell QD, CdSe/CdS quantum rods (QRs), and CdSe/CdS nanoplatelets (NPLs). Thereby, we focused on the applicability of these NPs for the polymerization synthesis approach used and quantified the preservation of the initial NP luminescence. The spectroscopic characterization of the resulting PMPs revealed the successful staining of the PMPs with luminescent CdSe/CdS QDs and CdSe/CdS NPLs. In contrast, usage of CdSe/CdS QRs and CdSe QDs with a ZnS shell did not yield luminescent PMPs. The results of this study provide new insights into structure–property relationships between NP stained PMPs and the initial luminescent NPs applied for staining and underline the importance of such studies for the performance optimization of NP-stained beads.

Novel Biomaterial-Derived Activated Carbon from Lippia Adoensis (Var. Koseret) Leaf for Efficient Organic Pollutant Dye Removal from Water Solution

Today, various pollutants, such as dyes from industries, are being released into the environment worldwide, posing significant challenges that require sustainable attention and advanced solutions. This research focuses on the synthesis and characterization of a novel biomaterial-based activated carbon (AC) derived from Lippia Adoensis (Koseret) leaves and investigates its effectiveness in removing MB from aqueous solutions. The biomaterial adsorbent derived from LA was subjected to proximate analysis, pH-point zero charge (pHpzc), FT-IR, and SEM characterization. The pHpzc results indicated a slightly acidic surface functional group for AC. The impact of temperature and chemical impregnation (H<sub>3</sub>PO<sub>4</sub>, NaCl and NaOH) was examined, with the optimal temperature of AC preparation found to be 600°C. The use of H<sub>3</sub>PO<sub>4</sub> for the chemical activation of biomaterials resulted in a high AC surface area. Batch adsorption experiments involved varying pH (2–10), dosage (0.1–0.35 g/50ml), initial concentration (10–35 ppm) and contact time (15–105 min). The optimal parameters were determined as pH = 8, dose = 0.25g, concentration = 10 ppm, and contact time = 75 min. The maximum adsorption capacity and removal efficiency were calculated as 3.99 and 92.2%, respectively. Thermodynamic analysis confirmed the spontaneous and endothermic nature of the system. Adsorption isotherm and kinetic studies revealed a good fit with the Langmuir isotherm (R<sup>2</sup>= 0.999), indicating monolayer adsorption and the pseudo-second order model, respectively. These findings suggest that the use of LA-AC could offer a cost-effective solution for the removal of methylene blue from water, contributing to the solution of water pollution challenges and promoting the adoption of eco-friendly wastewater treatment technologies.

Conformational and environmental effects on the electronic and vibrational properties of dyes for solar cell devices.

The main challenge for solar cell devices is harvesting photons beyond the visible by reaching the red-edge (650-780nm). Dye-sensitized solar cell (DSSC) devices combine the optical absorption and the charge separation processes by the association of a sensitizer as a light-absorbing material (dye molecules, whose absorption can be tuned and designed) with a wide band gap nanostructured semiconductor. Conformational and environmental effects (i.e., solvent, pH) can drastically influence the photophysical properties of molecular dyes. This study proposes a combined experimental and computational approach for the comprehensive investigation of the electronic and vibrational properties of a unique class of organic dye compounds belonging to the family of red-absorbing dyes, known as squaraines. Our focus lies on elucidating the intricate interplay between the molecular structure, vibrational dynamics, and optical properties of squaraines using state-of-the-art density functional theory calculations and spectroscopic techniques. Through systematic vibrational and optical analyses, we show that (i) the main absorption peak in the visible range is influenced by the conformational and protonation equilibria, (ii) the solvent polarity tunes the position of the UV-vis absorption, and (iii) the vibrational spectroscopy techniques (infrared and Raman) can be used as informative tools to distinguish between different conformations and protonation states. This comprehensive understanding offers valuable insights into the design and optimization of squaraine-based DSSCs for enhanced solar energy conversion efficiency.

Facile fabrication of MgAl2O4/MWCNT nanocomposite for efficient and stable solar-driven degradation of organic dye

This work reports the synthesis and characterization of Magnesium Aluminate (MgAl2O4) and Magnesium Aluminate/Multi Walled Carbon Nanotube (MgAl2O4/MWCNT) nanocomposite by facile chemical co-precipitation method for the dye degradation application. MgAl2O4 and MgAl2O4/MWCNT nanocomposite are characterized by Scanning Electron Microscopy (SEM), x-ray Diffractometry (XRD), Raman Spectrometry, UV–vis Spectrophotometry (UV–vis), Fourier Transform Infrared Spectroscopy(FTIR), and x-ray Photoelectron Spectroscopy (XPS). Surface morphology of MgAl2O4/MWCNT nanocomposite exhibits entangled needle-like structures while MgAl2O4 spinel comprises agglomerated nanoparticles of different sizes. XRD confirms the formation of MgAl2O4. XPS identifies the chemical states and binding energies of constituent elements present in the sample. Optical properties reveal that addition of MWCNTs in MgAl2O4 decreases the optical bandgap energy from 3.02 eV to 2.78 eV. MgAl2O4/MWCNT nanocomposite shows reduced bandgap compared to pristine MgAl2O4 due to increased chemical defects or vacancies in intergranular regions and chemical interaction between MgAl2O4 and MWCNT, leading to the formation of new energy levels in MgAl2O4/MWCNT nanocomposite. Addition of MWCNTs provides a large surface area, more active sites, and enhances electron mobility between energy levels. MgAl2O4/MWCNT nanocomposite proves itself a better photocatalyst due to the fast degradation of Methyl Blue (MB) in 65 min as compared to MgAl2O4 which degrades the dye in 90 min. MgAl2O4/MWCNT nanocomposite also shows good stability and reusability even after performing the six cycles of dye degradation.