Optimal Properties Research Articles

Effect of Mn2+ substitution on the dielectric properties of NaMg(PO3)3 ceramics at microwave and terahertz frequencies

In this study, NaMg1-xMnx(PO3)3 (0.00 ≤ x ≤ 0.0625) ceramics with low dielectric constant were prepared via the solid-state reaction method. The effects of Mn2+ substitution on the microstructure and dielectric properties (at microwave and terahertz frequencies) of the NaMg(PO3)3 ceramics were studied by means of the Rietveld refinement, morphology, and ionic polarizability analysis. It is obtained that the NaMg0.0975Mn0.025(PO3)3 ceramic sintered at 880 °C for 4 h exhibited optimal dielectric properties at microwave frequencies, where εr = 4.585, Q × f = 48,313 GHz (@17.228 GHz), and τf = −40.83 ppm/°C. The Q × f and τf values were changed by 74.2 % and 27.8 %, as compared to the values of 27,728 GHz and −56.52 ppm/°C for the pure NaMg(PO3)3 ceramic, respectively. For terahertz frequencies (0.2–1.0 THz), the εr values were decreased to 3.79–3.98, and the tanδ values were between 0.0203 and 0.1152. All the experimental results indicate that this system exhibits great potentials both at microwave and terahertz frequencies.

The effects of Ni and Al elements on microstructure and mechanical properties of low carbon CoCrMo alloy coatings

Low-carbon cobalt-based alloy coatings with high ductility and low thermal fatigue crack propagation rates were prepared using laser cladding (LC) technology. The microstructure of the coatings was characterized using SEM, EBSD, and TEM, while the mechanical properties were tested and analyzed. The CoCrMo alloy primarily consists of γ-Co and a minor amount of ε-Co. The addition of Ni increased the stacking fault energy (SFE), resulting in the retention of γ-Co in the alloy. However, the increase of Al content reduced the SFE, leading to the precipitation of Al3Ni intermetallic compound along with a eutectic region with Al3Ni, Cr23C6, and ε-Co. More ε-Co phase appeared after tensile deformation due to the stress-induced transformation induced plasticity (TRIP) effect. Ni addition increased the content of face-centered cubic (fcc) γ-Co, enhancing the coating's ductility by approximately 85 % compared to CoCrMo. With higher Al content, the ε-Co phase increased, and the dispersion of Al3Ni improved the coatings' strength. The jagged structure of the eutectic region increased the resistance to thermal fatigue crack propagation, causing the crack propagated along the grain boundary. Optimal mechanical properties were achieved with the addition of 13 wt% Ni and 7 wt% Al, which achieved a 53 % increase in ductility and a 40 % reduction in the thermal fatigue crack propagation rate compared to CoCrMo.

Composite cellulose/bismuth/PVA nanocrystal for high-performance X-ray radiation shielding

The strong penetrating power of X-rays causes serious health problems. Longer exposure to radiation that penetrates normal cells can result in gene mutations, cancer, and even death. Protection against radiation exposure is necessary to prevent negative impacts from occurring. This research aims to make apron samples using a simple method based on cellulose as a matrix, bismuth as a filler with concentrations of 1 g, 0.75 g, 0.25 g and PVA acts as a binder that helps bind cellulose and bismuth particles into an effective X-ray radiation shield. The characterization carried out includes Fourier transform infrared (FTIR) to determine the functional groups and chemical composition of the sample, x-ray diffraction (XRD) to analyze the crystal size of the sample, and mobile x-ray with energies of 60, 70, and 80 keV to determine the radiation shielding performance. The findings of this study highlight that the optimal shielding properties were attained by employing a sample with the highest concentration of bismuth filler, specifically at 1 g. This material exhibits outstanding characteristics, including a high linear attenuation coefficient and mass attenuation coefficient of 0.68 cm−1 and 2.24 cm2/g respectively for an energy of 60 keV and especially low HVL (1.01 cm) and TVL (3.36 cm) values. These findings have significant implications for developing high-performance X-ray radiation shielding materials, particularly in industries where radiation exposure is a concern, such as the medical industry, research, and laboratories. The high tensile strength (2.83 N/mm2) and elongation (12.09 %) values as well as the low Young's modulus (0.108 N/mm2) values also indicate the flexibility of the resulting material, which could be beneficial for applications that require flexible shielding materials. The practicality of this research makes the audience feel that the findings are applicable and useful in real-world scenarios.

Novel statistical investigation on performance measures of WEDM: Optimization, microstructure and mechanical properties

A comparative performance analysis has been investigated on wire electrical discharge machining (WEDM) responses while machining a hybrid titanium matrix composite (TMC) varying the key input parameters like power (P), peak current (IP) and time-off (Toff). Two novel multi-objective optimization algorithms are developed namely desirable multi-objective genetic algorithm (DMOGA) and desirable multi-objective giant pacific octopus optimizer (DMOGPOO) for tackling various issues in many industries like automobile valve pins in crank and cam shafts, aerospace propeller and biomedical implants. The principal advantage of DMOGA to other algorithm is accuracy and robustness. The novelty fits in the iterative progression of growth of efficient grandee set, uttered as population congregating to a fitness function. Many techniques frequently encounter substandard solutions when evaluating MOO problems, as opposed to solving properly approximated functions of Pareto optimal solutions in targets. DMOGPOO is an enthralling statistical method which mimics the octopus’s predatory behavior, performs better than other multi-objective optimization (MOO) algorithms, where the desirable objective functions is fetched in python using MOGPOO. In a multi-objective foraging environment, the archive was utilized to imitate octopus predatory behavior and establish social hierarchies. DMOGPOO approach is designed with multi-objective formulations to preserve and guarantee enhanced coverage of optimum solutions across all goals. Experimental investigation is accepted on material removal rate (MRR), surface roughness (SR), kerf width (KW) and over cut (OC). Combined desirability in case of DMOGA is 0.716 which improved to 0.813 when DMOGPOO is proposed. MOO is improved with DMOGPOO of 13.547% when contrasted with DMOGA, with MRR of 3.81 mm3/min, SR of 0.79 µm, KW of 0.349 mm, OC of 0.099 mm, and combined desirability of 0.813. Improved optimality set is obtained when DMOGPOO is used. %improvement of MRR is 5.54%, SR is 75.95%, KW is 0.29%, and OC is 4.21%.

Phenolic Foam Preparation Using Hydrofluoroolefin Blowing Agents and the Toughening Effect of Polyethylene Glycol.

In this work, a new class of fourth-generation, zero ozone depletion potential, hydrofluoroolefin-based blowing agents were used to prepare phenolic foam. While hydrofluoroolefin blowing agents have been used previously to prepare polyurethane foams, few studies have been reported on their use in phenolic foams. We introduce an effective method for foam preparation using two low-boiling blowing agents, cis-1,1,1,4,4,4-hexafluoro-2-butene and trans-1,1,1,4,4,4-hexafluoro-2-butene, and their combinations with hexane. Traditionally, phenolic foams have been prepared using chlorofluorocarbons and hydrochlorofluorocarbons, which can have harmful effects on the environment due to their high ozone depletion potential or global warming potential. Conductor-like screening model for real solvents (COSMO-RS) modeling studies were performed to understand the effects of different blowing agent combinations on their boiling points. A series of phenolic foams were prepared by varying the concentration of the hydrofluoroolefin and the hydrofluoroolefin-hexane blowing agent combinations. The concentrations of the surfactant, Agnique CSO 30, and the toughening agent, polyethylene glycol, were also varied to yield a formulation with the optimal properties. The foams formulated with the hydrofluoroolefin-hexane mixture displayed a higher compressive strength and a lower thermal conductivity than those prepared with either hydrofluoroolefin or hexane alone. The cell microstructure of all the foams was examined using scanning electron microscopy. By introducing flexible chains into the resin matrix, PEG facilitates proper distribution of hydrofluoroolefin-hexane blowing agents and other reagents and thereby increases the mechanical strength of the foam.

Biocomposite Scaffolds Based on Chitosan Extraction from Shrimp Shell Waste for Cartilage Tissue Engineering Application.

Chitosan-based scaffolding possesses unique properties that make it highly suitable for tissue engineering applications. Chitosan is derived from deacetylating chitin, which is particularly abundant in the shells of crustaceans. This study aimed to extract chitosan from shrimp shell waste (Macrobrachium rosenbergii) and produce biocomposite scaffolds using the extracted chitosan for cartilage tissue engineering applications. Chitinous material from shrimp shell waste was deproteinized and deacetylated. The extracted chitosan was characterized and compared to commercial chitosan through various physicochemical analyses. The findings revealed that the extracted chitosan shares similar trends in the Fourier transform infrared spectroscopy spectrum, energy dispersive X-ray mapping, and X-ray diffraction pattern to commercial chitosan. Despite differences in the degree of deacetylation, these results underscore its comparable quality. The extracted chitosan was mixed with agarose, collagen, and gelatin to produce the blending biocomposite AG-CH-COL-GEL scaffold by freeze-drying method. Results showed AG-CH-COL-GEL scaffolds have a 3D interconnected porous structure with pore size 88-278 μm, high water uptake capacity (>90%), and degradation percentages in 21 days between 5.08% and 30.29%. Mechanical compression testing revealed that the elastic modulus of AG-CH-COL-GEL scaffolds ranged from 44.91 to 201.77 KPa. Moreover, AG-CH-COL-GEL scaffolds have shown significant potential in effectively inducing human chondrocyte proliferation and enhancing aggrecan gene expression. In conclusion, AG-CH-COL-GEL scaffolds emerge as promising candidates for cartilage tissue engineering with their optimal physical properties and excellent biocompatibility. This study highlights the potential of using waste-derived chitosan and opens new avenues for sustainable and effective tissue engineering solutions.

Synthesis, optimization, electrochemical and electrochromic properties of Zr-doped NiO films by chemical spray pyrolysis

Zirconium (Zr)-doped NiO films with different contents were successfully synthesized via the chemical spray pyrolysis technique. The structure, morphology, optical and electrochemical behaviors of these films were investigated by X-ray diffraction (XRD), Raman spectrometer, scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), UV–Vis-NIR spectrophotometry, cyclic voltammetry (CV), and chronoamperometry (CA). XRD results suggested that the synthesized samples have the cubic crystal structure and a preferred orientation along the plane (111). Raman spectra further confirmed the successful incorporation of zirconium ions into the NiO films. SEM images explained that the surfaces of the doped films were composed of uniform and dense nanoparticles. EDS analysis suggested that Zr, Ni and O elements were uniformly distributed on the films. The optical results showed that the band gap decreases from 3.53 eV to 3.47 eV as the increase of zirconium doping content. The electrochemical analysis suggested that zirconium doping improved the specific capacitance of the NiO films (the NiO film with the Zr amount of 7 %, 59 F/g at 6 mV/s). In addition, the NiO film with 5 % Zr doped amount exhibited the largest ΔOD (81 %), the largest CE (60.37 cm2/C), and the fastest coloring time (tc =2.1 s) and bleaching time (tb = 2.4 s). These results showed that this film had the excellent electrochromic properties, suggesting that the optimal Zr doped amount of NiO films is 5 %. As a novel kind of electrochromic material, the Zr-doped NiO film has broad application prospects in smart windows, green buildings and energy efficient utilization fields.

Evolution of Physical, Thermal, and Mechanical Properties of Poly(methyl Methacrylate)-Based Elium Thermoplastic Polymer During Polymerization.

Elium-based thermoplastic composites are a key material for future use in the marine, wind energy, and automotive industries because of their recyclability and ease of manufacture. To optimize the processing of the Elium composites to yield optimal structural properties, computational process modeling can be used to relate processing parameters to residual stresses and material durability. The key ingredient for reliable and accurate process modeling is the evolution of physical, thermal, and mechanical properties during polymerization. The objective of this study is to use molecular dynamics to predict the mass density, bulk modulus, shear modulus, Young's modulus, Poisson's ratio, glass transition temperature, and coefficient of thermal expansion as a function of the extent of reaction of the polymer. The predicted properties compare favorably to the experimentally measured values in the fully polymerized state. This data set of properties provides needed input data for process modeling of Elium-based composites for process parameter optimization and improved durability and performance.

The Characterization of a Low-Calorie and Lactose-Free Brown Fermented Milk by the Hydrolysis of Different Enzymatic Lactose.

The adoption of brown fermented milk in the normal diet and daily beverages is accompanied by significant sugar intake and a high public health burden. To reduce the sugar content in dairy products while maintaining optimal nutritional properties, a novel low-calorie, lactose-free brown fermented milk was developed through enzymatic hydrolysis and the Maillard reaction. The optimal product was achieved using low-temperature lactase, where the lactose and glucose content were reduced 33-fold and 2.4-fold to 0.06 g/100 g and 13.32 g/L, respectively, meeting the criteria for being lactose-free (<0.5 g/100 g). Meanwhile, hazardous compounds such as 5-hydroxymethylfurfural and 3-deoxyglucosone were reduced by more than 20%. After 28 days of storage, the water-holding capacity and suspension stability remained notably stable, and the protein composition was also more enriched compared to commercial milk. It is expected that this low-calorie dairy product may promote growth in the dairy market.

Gelatin-Sodium Alginate Hydrogels Cross-Linked by Squaric Acid and Dialdehyde Starch as a Potential Bio-Ink.

Hydrogels as biomaterials possess appropriate physicochemical and mechanical properties that enable the formation of a three-dimensional, stable structure used in tissue engineering and 3D printing. The integrity of the hydrogel composition is due to the presence of covalent or noncovalent cross-linking bonds. Using various cross-linking methods and agents is crucial for adjusting the properties of the hydrogel to specific biomedical applications, e.g., for direct bioprinting. The research subject was mixtures of gel-forming polymers: sodium alginate and gelatin. The polymers were cross-linked ionically with the addition of CaCl2 solutions of various concentrations (10%, 5%, 2.5%, and 1%) and covalently using squaric acid (SQ) and dialdehyde starch (DAS). Initially, the polymer mixture's composition and the hydrogel cross-linking procedure were determined. The obtained materials were characterized by mechanical property tests, swelling degree, FTIR, SEM, thermal analysis, and biological research. It was found that the tensile strength of hydrogels cross-linked with 1% and 2.5% CaCl2 solutions was higher than after using a 10% solution (130 kPa and 80 kPa, respectively), and at the same time, the elongation at break increased (to 75%), and the stiffness decreased (Young Modulus is 169 kPa and 104 kPa, respectively). Moreover, lowering the concentration of the CaCl2 solution from 10% to 1% reduced the final material's toxicity. The hydrogels cross-linked with 1% CaCl2 showed lower degradation temperatures and higher weight losses than those cross-linked with 2.5% CaCl2 and therefore were less thermally stable. Additional cross-linking using SQ and DAS had only a minor effect on the strength of the hydrogels, but especially the use of 1% DAS increased the material's elasticity. All tested hydrogels possess a 3D porous structure, with pores of irregular shape and heterogenic size, and their swelling degree initially increased sharply to the value of approx. 1000% during the first 6 h, and finally, it stabilized at a level of 1200-1600% after 24 h. The viscosity of 6% gelatin and 2% alginate solutions with and without cross-linking agents was similar, and they were only slightly shear-thinning. It was concluded that a mixture containing 2% sodium alginate and 6% gelatin presented optimal properties after gel formation and lowering the concentration of the CaCl2 solution to 1% improved the hydrogel's biocompatibility and positively influenced the cross-linking efficiency. Moreover, chemical cross-linking by DAS or SQ additionally improved the final hydrogel's properties and the mixture's printability. In conclusion, among the tested systems, the cross-linking of 6% gelatin-2% alginate mixtures by 1% DAS addition and 1% CaCl2 solution is optimal for tissue engineering applications and potentially suitable for 3D printing.

COMPARATIVE EFFECT OF WOODFLOUR AND GRANULATED RICE HUSK ON THE THERMAL INSULATION OF TERMITE HILL CLAY

This research work covered the comparative effect of wood flour (saw dust) and granulated rice husk on the thermal insulation of termite hill clay. The raw clay samples were mined from the Federal University of Technology Akure Campus and processed. Likewise, the saw dust and rice husk were also processed and grinded. The clay samples and the additives were sieved to obtain 300 microns and were mixed in predetermined proportions of 0, 2, 4, 6, 8 and 10 wt. %. Cylindrical samples were developed from the mixtures which were compacted and then air dried before oven dried and finally fired. The fired samples were subjected to selected tests to determine their insulation and refractory properties. These tests include porosity, linear shrinkage, volumetric shrinkage, bulk density, thermalconductivity, thermal shock resistance and cold crushing tests. It was discovered that the saw dust samples meet the ASTM standard for insulating bricks while the rice husk samples did not. Saw dust samples with 2 and 8 wt. % were ones with optimum properties.

Optimized UV-barrier carboxymethyl cellulose-based edible coatings reinforced with green synthesized ZnO-NPs for food packaging applications

AbstractThe widespread use of sodium carboxymethyl cellulose (CMC) in the production of edible coatings is returned to its biodegradable, biocompatible, and non-toxic nature. However, neat CMC edible coatings lack UV-shielding activity and have poor antimicrobial properties. This study aimed to develop a CMC-based coating with optimal UV-barrier properties by incorporating aloe vera (AV) and green synthesized zinc oxide nanoparticles (ZnO-NPs). The composition and synergistic effects of CMC, AV, and ZnO-NPs were optimized using central composite design to achieve the best UV-barrier properties. When using the optimized compositions of CMC (1.0 g), AV (3.0 g), and ZnO-NPs (5.0 wt%), the minimum UV-transmittance achieved was 4.75%. Fourier transform infra-red and wide-angle X-ray diffraction were used to confirm the interactions between the coating components. The incorporation of ZnO-NPs into CMC/AV was validated through surface morphology analysis via scanning electron microscopy and by examining the distribution of ZnO-NPs using transmission electron microscopy. CMC/AV/ZnO-NPs coatings showed excellent water barrier, mechanical, thermal, and antimicrobial properties when compared with the neat carboxymethyl cellulose coating. In addition, CMC/AV/ZnO-NPs coatings significantly resisted both mass loss and spoilage of green capsicum for a 15-day storage period. These results proved that the optimized coating could replace the plastic packaging candidates and be used potentially to preserve food products.

Influence of fish-scale powder addition and stacking order on mechanical and thermal properties of hybrid kenaf/glass polyester composites

The increasing concern for the environment has driven a surge in popularity of utilizing modern technology to develop new products from renewable resources. To address this, polymer composites are incorporating various bio-waste materials as filler components. This study focuses on fabricating four-layered hybrid polyester laminates using kenaf (K), glass (G), and reinforced with fish scale (FS) powder at concentrations ranging from 5 wt.% to 15 wt.%. Mechanical properties are assessed following ASTM standards to evaluate the optimal FS filler percentage. The results reflect that the KGKG laminate with 15 wt. % FS exhibits utmost tensile strength and hardness, while the same laminate with 10 wt. % FS shows optimal flexural and impact properties. Further, numerical analysis is performed using ANSYS 19.0 software to validate the experimental findings. It is marked that, the results of numerical analysis are align intimately with the experimental data, with a deviation of 5 to 10%. Additionally, the moisture absorption behavior is investigated, and the results revealing that FS filler reduced moisture uptake and enhanced dimensional stability. Further, the study is extended to investigate the thermal attributes of laminates through Thermogravimetric Analysis (TGA) and Dynamic Mechanical Analysis (DMA). The fractured surface morphology are studied through Scanning Electron Microscopic (SEM) and the findings reveal significant occurrences of matrix cracking, fiber withdrawal, and the separation of fibers from the matrix. Overall, this study suggests the incorporation of FS bio-fillers into hybridized kenaf/glass laminates in order to improve performance and create environmentally friendly options that suitable for automotive applications.

Discovery and structure − activity relationships of 2,4,5-trimethoxyphenyl pyrimidine derivatives as selective D5 receptor partial agonists

Dopamine receptors are therapeutic targets for the treatment of various neurological and psychiatric disorders, including Parkinson’s and Alzheimer’s. Previously, PF-06649751 (tavapadon), PF-2562 and PW0464 have been discovered as potent and selective G protein-biased D1/D5 receptor agonists with optimal pharmacokinetic properties. However, no selective D5R agonist has been reported yet. In this context, we designed and synthesized forty non-catecholamines-based pyrimidine derivatives and identified four pyrimidine derivatives as selective D5R partial agonists. Using cAMP-based GloSensor assay in transiently transfected HEK293T cells with human D1 or D5 receptors, we discovered that compound 5c (4-(4-bromophenyl)-6-(2,4,5-trimethoxyphenyl)pyrimidin-2-amine) exhibited modest D5R agonist activity. This leads us to explore various modifications of this scaffold to improve the D5 agonist potency and efficacy. Using molecular docking, and rational design followed by their evaluation at D1 and D5 receptors for agonist activity, we identified three new derivatives, 5j, 5h, and 5e. The most potent compound of this series 5j (4-(4-iodophenyl)-6-(2,4,5-trimethoxyphenyl)pyrimidin-2-amine), exhibited EC50 of 269.7 ± 6.6 nM. Mice microsomal stability studies revealed that 5j is quite stable (>70 % at 1 hr). Furthermore, pharmacokinetic analysis of 5j (20 mg/kg, p.o) in C57BL/6j mice showed that 5j is readily absorbed via oral route of dosing and also enters into the brain (plasma Tmax: 1 h, Cmax: 51.10 ± 13.51 ng/ml; Brain Tmax: 0.5 h, Cmax: 22.54 ± 4.08 ng/ml). We further determined the in-vivo effect of 5j on cognition in scopolamine-induced amnesia in C57BL/6j mice. We observed that 5j (10 mg/kg, p.o) alleviated scopolamine-induced impairment in short-term memory and social recognition, which were blocked by D1/D5 antagonist SCH23390 (0.1 mg/kg, i.p.). Furthermore, 5j did not exhibit any cytotoxicity (up to 10 µM) or in vivo acute toxicity up to 200 mg/kg (p.o). These results strongly suggest that 5j could be further developed for treating neurological disorders wherein the D5 receptors play pivotal roles.

A Computational Framework to Optimize the Mechanical Behavior of Synthetic Vascular Grafts.

The failure of synthetic small-diameter vascular grafts has been attributed to a mismatch in the compliance between the graft and native artery, driving mechanisms that promote thrombosis and neointimal hyperplasia. Additionally, the buckling of grafts results in large deformations that can lead to device failure. Although design features can be added to lessen the buckling potential, the addition is detrimental to decreasing compliance (e.g., reinforcing coil). Herein, we developed a novel finite element framework to inform vascular graft design by evaluating compliance and resistance to buckling. A batch-processing scheme iterated across the multi-dimensional design parameter space, which included three parameters: coil thickness, modulus, and spacing. Three types of finite element models were created in FEBio for each unique coil-reinforced graft parameter combination to simulate pressurization, axial buckling, and bent buckling, and results were analyzed to quantify compliance, buckling load, and kink radius, respectively, from each model. Importantly, model validation demonstrated that model predictions agree qualitatively and quantitatively with experimental observations. Subsequently, data for each design parameter combination were integrated into an optimization function for which a minimum value was sought. The optimization values identified various candidate graft designs with promising mechanical properties. Our investigation successfully demonstrated the model-directed framework identified vascular graft designs with optimal mechanical properties, which can potentially improve clinical outcomes by addressing device failure. In addition, the presented computational framework promotes model-directed device design for a broad range of biomaterial and regenerative medicine strategies.

Connection between higher order measures of risk and stochastic dominance

Higher order risk measures are stochastic optimization problems by design, and for this reason they enjoy valuable properties in optimization under uncertainties. They nicely integrate with stochastic optimization problems, as has been observed by the intriguing concept of the risk quadrangles, for example. Stochastic dominance is a binary relation for random variables to compare random outcomes. It is demonstrated that the concepts of higher order risk measures and stochastic dominance are equivalent, they can be employed to characterize the other. The paper explores these relations and connects stochastic orders, higher order risk measures and the risk quadrangle. Expectiles are employed to exemplify the relations obtained.

From Powders to Alloys: A Study of the Mechanical Alloying Process and Sintering

This study explores the intricacies of mechanical alloying, aiming to unlock its potential in modern engineering. It investigates the impact of milling duration, ball-to-powder ratio, and sintering temperature on the microstructure and mechanical properties of Al-7Zn-2.5Mg-2.5Cu alloy and Al7075 alloy. Mechanical alloying can produce alloys with exceptional hardness, strength, and ductility, while grain size can be controlled by adjusting milling parameters. Experimental techniques like X-Ray diffraction and transmission electron microscopy reveal microstructural changes during mechanical alloying, aiding in understanding metastable phases and element segregation, which influence the alloy’s properties. Sintering, the subsequent consolidation step, determines final properties, with a trade-off between grain size and mechanical qualities observed at different sintering temperatures. This trade-off presents an intriguing avenue for developing materials with optimal properties. The study also explores potential applications of mechanical alloying across industries, including aerospace, biomedical, and energy. These unique mechanical alloys are attractive for various uses, from structural to catalytic and magnetic materials. They have the potential to revolutionize industries and drive technological advancements.

Self-Sensing Potential of Metashale Geopolymer Mortars with Carbon Fiber/Graphite Powder Admixtures

Multifunctional building materials with self-sensing capability have great potential for civil engineering applications. The self-sensing capability of typically calcium aluminosilicate matrices of cementitious or geopolymer materials is adopted by admixing electrically conductive admixtures in an amount that ensures optimal electrical properties and their proportionality to mechanical loading. The paper aims to evaluate the self-sensing capability of 4 metashale geopolymer mortars with graphite powder (GP) and carbon fibers (CF) in different ratios, including MGF 5/0, MGF 4.5/0.5, MGF 4/1, and MGF 3/0. The 4-probe measurements at 21 V DC input voltage on (100 × 100 × 100) mm3 samples with embedded copper-grid electrodes evaluate the gauge factor, which corresponds to the monitored changes in electrical resistivity. Despite the limitations of DC measurements, the self-sensing capability is observed for all the mixtures. The most promising response to dynamic loading with an FCR of 0.018%, is observed for the MGF 4.5/0.5 sample.

Cell-free protein synthesis with technical additives - expanding the parameter space of in vitro gene expression.

Biocatalysis has established itself as a successful tool in organic synthesis. A particularly fast technique for screening enzymes is the in vitro expression or cell-free protein synthesis (CFPS). The system is based on the transcription and translation machinery of an extract-donating organism to which substrates such as nucleotides and amino acids, as well as energy molecules, salts, buffer, etc., are added. After successful protein synthesis, further substrates can be added for an enzyme activity assay. Although mimicking of cell-like conditions is an approach for optimization, the physical and chemical properties of CFPS are not well described yet. To date, standard conditions have mainly been used for CFPS, with little systematic testing of whether conditions closer to intracellular conditions in terms of viscosity, macromolecules, inorganic ions, osmolarity, or water content are advantageous. Also, very few non-physiological conditions have been tested to date that would expand the parameter space in which CFPS can be performed. In this study, the properties of an Escherichia coli extract-based CFPS system are evaluated, and the parameter space is extended to high viscosities, concentrations of inorganic ion and osmolarity using ten different technical additives including organic solvents, polymers, and salts. It is shown that the synthesis of two model proteins, namely superfolder GFP (sfGFP) and the enzyme truncated human cyclic GMP-AMP synthase fused to sfGFP (thscGAS-sfGFP), is very robust against most of the tested additives.

Structure-preserving finite element methods for computing dynamics of rotating Bose-Einstein condensate

This work is concerned with the construction and analysis of structure-preserving Galerkin methods for computing the dynamics of rotating Bose-Einstein condensate (BEC) based on the Gross-Pitaevskii equation with angular momentum rotation. Due to the presence of the rotation term, constructing finite element methods (FEMs) that preserve both mass and energy remains an unresolved issue, particularly in the context of nonconforming FEMs. Furthermore, in comparison to existing works, we provide a comprehensive convergence analysis, offering a thorough demonstration of the methods’ optimal and high-order convergence properties. Finally, extensive numerical results are presented to check the theoretical analysis of the structure-preserving numerical method for rotating BEC, and the quantized vortex lattice’s behavior is scrutinized through a series of numerical tests.