Optimized Preparation Procedure Research Articles

Small animal patient preoperative preparation: a review of common antiseptics, comparison studies, and resistance.

This review aims to describe commonly used antiseptics in veterinary medicine including their mechanism of action, spectrum of activity, potential adverse effects, and application techniques. Additionally, it provides a review of the veterinary literature comparing antiseptics, a discussion of effectiveness and efficacy studies, and the potential for increased resistance to biocides and antimicrobials. This review concludes that appropriate selection and use is necessary to prevent the occurrence of surgical site infections, adverse effects, and potential for increasing resistance to antimicrobials. Continued research is needed to fill gaps in the current knowledge such as optimal preparation procedures for various surgical sites, standardization of efficacy and effectiveness testing, and the clinical impact of decreased susceptibility to chlorhexidine and other antiseptics.

Investigation of snow cover solid phase using total‐reflection x‐ray fluorescence method for an assessment of the environmental pollution

AbstractSnow cover is an important source of data for the study of environmental pollution due to its ability to accumulate atmospheric dust particles. A total reflection x‐ray fluorescence method (TXRF) was applied to assess the concentration levels of potentially toxic elements (As, Pb, Zn, Ni, Cu, Cr, V, Mn, and Sr) in samples of snow cover solid phase collected in suburban areas of the Irkutsk region with industrial activity. Suspension was chosen as an optimal sample preparation procedure for solid phases of snow samples obtained after melting and filtration. Results were compared with those obtained by wavelength‐dispersive x‐ray fluorescence spectrometry and atomic absorption spectrometry. Precision of TXRF results expressed by repeatability values was not exceeded 15% (n = 3) for most of the elements, and the trueness of the TXRF method expressed by recovery values was in the range of 87%–115% for concentration levels of 5.0–350 μg/g. Forty samples of snow cover solid phase were analyzed by TXRF method and results were compared with the background values. The investigation showed low contamination of the studied area by Pb, Cu, V, Mn, and Sr, medium contamination by Ni, As, and Cr, and high contamination by Zn. TXRF is advantageous in being rapid, cost‐efficient, and simple and can be used as a promising method for an assessment of environmental pollution.

Determination of multiclass contaminants in chilli powder based on magnetic multiwalled carbon nanotubes and UPLC-QTOF/MS

A multiclass analysis approach was developed using magnetic multiwalled carbon nanotubes sorbents and ultra-high performance liquid chromatography-quadrupole time-of-flight mass spectrometry (UPLC-QTOF/MS) for the rapid screening and simultaneous determination of 216 contaminants including 15 mycotoxins, 9 synthetic colourants, and 192 pesticides in chilli powder. The sample preparation process was optimized. The optimal preparation procedure utilized NaCl and NaAc as the salting-out agents, and Fe3O4-MWCNTs as the sorbents, resulting in reduced chemical consumption, improved cleaning performance, and facilitated high-throughput analysis. The proposed method was validated, and satisfactory parameters were obtained. Approximately 85.6% of the target analytes exhibited a weak matrix effect, with the matrix effects falling within the range of 0.8 ∼ 1.2. The method demonstrated acceptable recoveries of the analytes, falling within the range of 62.14%∼119.76% at three fortified levels with relative standard deviations (RSDs) of less than 20%. Additionally, the method’s limit of quantification (LOQ) ranged from ranged from 0.50 μg·kg−1 to 49.56 μg·kg−1. The method was further applied for analysis of 27 chilli powder samples, demonstrating its potential for screening and quantification of multiclass contaminants for spices.

An umbrella review of the use of platelet-rich plasma in the treatment of androgenetic alopecia.

To evaluate the efficacy of platelet-rich plasma (PRP) in the treatment of androgenetic alopecia, as well as establish an effective treatment protocol and optimal PRP preparation procedure. We searched the PubMed, Scopus, Embase, Cochrane, CNKI, and Wanfang databases from inception to October 29, 2021, using PROSPERO's International Prospective Register of Systematic Reviews (registration ID: CRD42022295921). The original literature search revealed 215 reviews; after duplication removal, 89 papers were eliminated, 95 were eliminated after reading the titles and abstracts, and eventually, 28 articles were included after reading the complete text. PRP treatment for androgenetic alopecia is effective, and we recommend the following: (1) a PRP volume of at least 0.05 ml/cm2 , preferably 0.1ml/cm2 ; (2) at least three consecutive treatments at an interval of 1month; (3) intensive therapy is beneficial and can be provided from 3 to 6months after continuous treatment; (4) objective indicators such as hair diameter, hair count; (5) long-term follow-up.

Optimization of a Liposomal DNase I Formulation with an Extended Circulating Half-Life.

Drug delivery systems such as liposomes are widely used to stabilize and increase the plasma half-life of therapeutics. In this article, we have investigated two strategies to increase the half-life of deoxyribonuclease I, an FDA-approved enzyme used for the treatment of cystic fibrosis, and a potential candidate for the reduction of uncontrolled inflammation induced by neutrophil extracellular traps. We demonstrate that our optimized preparation procedure resulted in nanoparticles with improved plasma half-life and total exposure relative to native protein, while maintaining enzymatic activity.

Concentration-dependent adsorption behaviors and mechanisms for ammonium and phosphate removal by optimized Mg-impregnated biochar

Using biochar as an adsorbent is a promising technique for simultaneous recovery of ammonium and phosphate from wastewater. However, deficiencies in studying the optimal preparation procedures and aqueous-condition-related adsorption mechanisms of biochar limited its large-scale application. In this study, the optimized Mg-impregnated biochar showed excellent Langmuir maximum adsorption capacities of 5.5 and 4.4 mmol/g for ammonium and phosphate, respectively, owing to the well-developed pore structures with high Mg content and the abundant oxygen-containing functional groups. Meanwhile, turning points in the curve of removal efficiency against initial concentration suggested a concentration-dependent adsorption behavior, which was also greatly affected by the solution pH and co-existing substances. Characterizing the adsorption mechanisms of biochar indicated that, when the concentrations of nutrient ions were low, a small amount of ammonium would be released, while phosphate was adsorbed by electrostatic interaction and Mg3(PO4)2 precipitation following the ratio of 1:3. In comparison, when the concentrations of nutrient ions were high, >98% of adsorbed phosphate and >80% of adsorbed ammonium were precipitated together as struvite, while the remaining adsorbed ammonium complexed with oxygen-containing functional groups. This study revealed the discrepant performances of Mg-impregnated biochar under different aqueous conditions, which could be a key influencing factor concerning its real application in nutrient recovery.

Micelle separation conditions based on particle size strongly affect carotenoid bioaccessibility assessment from juices after in vitro digestion

For assessing the carotenoid bioaccessibility during in vitro digestion, obtaining the micelle fraction that can diffuse through the mucin layer according to the particle size is an important step. However, the accuracy of the various approaches to obtaining the right fraction of micelles described in literature has not been investigated. In many studies the reported bioaccessible fraction might therefore be over- or underestimating the real bioaccessibility. The present study aimed to fill this gap and give approaches to get accurate data on the bioaccessible fraction from samples with different properties. Results illustrated that optimizing the centrifugal speed and duration of the digesta are essential in obtaining the micelle fraction. Different digesta have different optimum centrifugal parameters to obtain the bioaccessible fraction. 6,000 rpm and 40 min was selected as the optimum centrifugal parameter for combined juice (CJ). 6,000 rpm and 60 min was the optimum centrifugal parameter for CJ with oil, and CJ with emulsion using non-ionic emulsifier. 8,000 rpm and 20 min was the optimum centrifugal parameter for CJ with emulsion using ionic emulsifier. Polygalacturonanase (PG)-digested systems required higher centrifugal speed (10,000 rpm) compared with CJ-based systems (6,000 rpm or 8,000 rpm). A prediction model to determine the optimal centrifugation speed/time from the properties of the intestinal digesta was developed. Sample preparation conditions strongly affect carotenoid bioaccessibility assessment from juices during in vitro digestion. Based on these results, it is highly recommended to perform an optimized preparation procedure for bioaccessible fraction prior to carotenoid bioaccessibility analysis.

An Optimized Preparation Procedure of Tetrabasic Lead Sulfate for Lead-Acid Batteries

The addition of tetrabasic lead sulfates (4BS) as additives to positive pastes will effectively address the shortcomings which occur during the usage of Lead-acid batteries, such as the premature capacity loss and the active substances shed in the positive paste. We synthesized 4BS seeds using the doped lead sulfate atmospheric hydrothermal method with the lead oxide, lead sulfate, and sulfuric acid as reactant. The purity and yield of 4BS reach above 99% and 92.5%, respectively, and the particle size was approximately 10 μm. The products have been characterized by scanning electron microscope and X-ray diffractometer. Composition analysis and processing method exploration of the effluent from the 4BS synthesis were finished as well.

Hyaluronic Acid Coating Reduces the Leakage of Melittin Encapsulated in Liposomes and Increases Targeted Delivery to Melanoma Cells.

Melittin is a promising antitumor substance; however, it is a nonspecific cytolytic peptide, which limits its clinical application. In this study, melittin liposomes (Mel-Lip) and hyaluronic acid (HA)-modified Mel-Lip (Mel-HA-Lip) were designed to reduce the toxicity and increase the anti-tumor effects of melittin. The optimal preparation procedure was evaluated using a uniform design based on the single factor method, and the concentration of HA was determined based on the cellular uptake of coumarin 6 labeled HA-Lip. Liposomes and HA-modified liposomes were evaluated in vitro by assessing cytotoxicity, cellular uptake, and release behavior. Liposomes prepared in the optimum formulation improved stability, with a particle size of 132.7 ± 1.55 nm, zeta potential of −11.5 ± 1.51 mV, entrapment efficiency of 86.25 ± 1.28%, and drug-loading efficiency of 3.91 ± 0.49%. Cellular uptake tests revealed that the uptake of nanoparticles significantly increased with HA modification, suggesting that HA modification enhanced the internalization of liposomes within cells, which was consistent with the results of the cytotoxicity analysis. Furthermore, in vitro release experiments showed that Mel-HA-Lip possessed a stronger sustained-release effect compared with Mel-Lip. The results of this experiment provide insight into the potential tumor-targeting effects of melittin.

Atomically-smooth single-crystalline VO2 (101) thin films with sharp metal-insulator transition

Atomically-abrupt interfaces in transition metal oxide (TMO) heterostructures could host a variety of exotic condensed matter phases that may not be found in the bulk materials at equilibrium. A critical step in the development of such atomically-sharp interfaces is the deposition of atomically-smooth TMO thin films. Optimized deposition conditions exist for the growth of perovskite oxides. However, the deposition of rutile oxides, such as VO2, with atomic-layer precision has been challenging. In this work, we used pulsed laser deposition to grow atomically-smooth VO2 thin films on rutile TiO2 (101) substrates. We show that an optimal substrate preparation procedure followed by the deposition of VO2 films at a temperature conducive for step-flow growth mode is essential for achieving atomically-smooth VO2 films. The films deposited at optimal substrate temperatures show a step and terrace structure of the underlying TiO2 substrate. At lower deposition temperatures, there is a transition to a mixed growth mode comprised of island growth and layer-by-layer growth modes. VO2 films deposited at optimal substrate temperatures undergo a sharp metal to insulator transition, similar to that observed in bulk VO2, but at a transition temperature of ∼325K with ∼103 times increase in resistance.

Surface-enhanced ZnS:Ag quantum dots scintillator

Surface-enhanced ZnS: Ag quantum dots scintillator has been manufactured by coupling quantum dots and dendritic silver surface-enhanced substrates. Four-fold enhancement of the fluorescence intensity was achieved compare to the undoped quantum dots without surface-enhanced substrates. Two silicon layers of certain thickness were used to prevent quenching of the fluorescence by monitoring the distance between quantum dots and surface-enhanced substrates. The enhancement results show consistence with theories, and larger enhancement factor is possible to be obtained with optimal preparation procedure. This study suggests a new method to achieve high performance quantum dots scintillator beneficial to radiation detection applications.

Economically Motivated Adulteration of Lemon Juice: Cavity Ring Down Spectroscopy in Comparison with Isotope Ratio Mass Spectrometry: Round-Robin Study

Abstract Background: Economically motivated adulteration (EMA) of foods has become an increasing concern in recent years, with lemon juice as a popular target. Objective and Method: In this work, an optimized preparation procedure for the isolation of citric acid from lemon juice was validated using elemental analyzer-isotope ratio MS (EA-IRMS) to detect adulteration with exogenous citric acid. Additionally, 69 imported lemon juice samples were evaluated using combustion module-cavity ring down spectrometry (CM-CRDS) and compared with the well-established EA-IRMS. Equivalency of CM-CRDS to EA-IRMS was further demonstrated by conducting a round-robin study involving eight laboratories throughout the United States, Canada, and New Zealand. Results: Overall, the results obtained for CM-CRDS were statistically indistinguishable from the results obtained using EA-IRMS for EMA lemon juice analysis. Conclusions: Therefore, CM-CRDS is a viable option for this application. Highlights: The CM-CRDS instrumentation is easy to operate, robust, and provides δ13C values comparable to EA-IRMS for citrate analysis. Through a multi-laboratory exercise, CM-CRDS was shown to be an alternative to EA-IRMS in the detection of economic adulteration of lemon juice.

Economically Motivated Adulteration of Lemon Juice: Cavity Ring Down Spectroscopy in Comparison with Isotope Ratio Mass Spectrometry: Round-Robin Study.

Background: Economically motivated adulteration (EMA) of foods has become an increasing concern in recent years, with lemon juice as a popular target. Objective and Method: In this work, an optimized preparation procedure for the isolation of citric acid from lemon juice was validated using elemental analyzer-isotope ratio MS (EA-IRMS) to detect adulteration with exogenous citric acid. Additionally, 69 imported lemon juice samples were evaluated using combustion module-cavity ring down spectrometry (CM-CRDS) and compared with the well-established EA-IRMS. Equivalency of CM-CRDS to EA-IRMS was further demonstrated by conducting a round-robin study involving eight laboratories throughout the United States, Canada, and New Zealand. Results: Overall, the results obtained for CM-CRDS were statistically indistinguishable from the results obtained using EA-IRMS for EMA lemon juice analysis. Conclusions: Therefore, CM-CRDS is a viable option for this application. Highlights: The CM-CRDS instrumentation is easy to operate, robust, and provides δ13C values comparable to EA-IRMS for citrate analysis. Through a multi-laboratory exercise, CM-CRDS was shown to be an alternative to EA-IRMS in the detection of economic adulteration of lemon juice.

Prospects to the formation and control of potential dimer impurity E of pantoprazole sodium sesquihydrate

Pantoprazole sodium, a substituted benzimidazole derivative, is an irreversible proton pump inhibitor which is primarily used for the treatment of duodenal ulcers, gastric ulcers, and gastroesophageal reflux disease (GERD). The monographs of European Pharmacopoeia (Ph. Eur.) and United States Pharmacopoeia (USP) specify six impurities, viz.; impurities A, B, C, D, E and F, respectively for its active pharmaceutical ingredient (API). The identification and synthesis of all impurities except impurity E are well described in the literature; however, there is no report related to impurity E. The prospects to the formation and controlling of impurity E up to ≤0.03% in the synthesis of pantoprazole sodium sesquihydrate (PAN) were discussed in detail for the first time. The present work described the journey towards the successful development of an optimal preparation procedure of dimer impurity E. The most plausible mechanism involved in the formation of impurity E has been proposed.

Preparation and application of a new catalyst to produce bio-oil from microalgae liquefaction

In this study, hydrothermal catalytic liquefaction method was adopted to produce bio-oil from microalgae. The influence of supported Ni-Catalysts doped neodymium (Nd) on the bio-oil yield from microalgae liquefaction was investigated, aiming to find the optimal preparation procedure of bio-oil. It proved that under the condition of a temperature of 270°C and a reaction period of 30 min, the bio-oil yield of hydrothermal catalytic liquefaction of spirulina powder could reach 55.1% by means of the catalyst prepared with 1 mol/L neodymium nitrate as the dipping solution after a calcination for 4 h at 800°C. In addition, the characterization on catalyst was discussed in this research. Keywords: catalyst, bio-oil, microalgae, catalytic liquefaction, spirulina powder DOI: 10.3965/j.ijabe.20171001.2599 Citation: Wang Y P, Nan G, Wang W J, Zhang J L, Han W. Preparation and application of a new catalyst to produce bio-oil from microalgae liquefaction. Int J Agric & Biol Eng, 2017; 10(1): 169–175.

Strong synergistic effects in PLA/PCL blends: Impact of PLA matrix viscosity

Blends of two biodegradable polymers, poly(lactic acid) (PLA) and poly(ϵ-caprolactone) (PCL), with strong synergistic improvement in mechanical performance were prepared by melt-mixing using the optimized composition (80/20) and the optimized preparation procedure (a melt-mixing followed by a compression molding) according to our previous study. Three different PLA polymers were employed, whose viscosity decreased in the following order: PLC ≈ PLA1 > PLA2 > PLA3. The blends with the highest viscosity matrix (PLA1/PCL) exhibited the smallest PCL particles (d∼0.6μm), an elastic-plastic stable fracture (as determined from instrumented impact testing) and the strongest synergistic improvement in toughness (>16× with respect to pure PLA, exceeding even the toughness of pure PCL). According to the available literature, this was the highest toughness improvement in non-compatiblized PLA/PCL blends ever achieved. The decrease in the matrix viscosity resulted in an increase in the average PCL particle size and a dramatic decrease in the overall toughness: the completely stable fracture (for PLA1/PCL) changed to the stable fracture followed by unstable crack propagation (for PLA2/PCL) and finally to the completely brittle fracture (for PLA3/PCL). The stiffness of all blends remained at well acceptable level, slightly above the theoretical predictions based on the equivalent box model. Despite several previous studies, the results confirmed that PLA and PCL could behave as compatible polymers, but the final PLA/PCL toughness is extremely sensitive to the PCL particle size distribution, which is influenced by both processing conditions and PLA viscosity. PLA/PCL blends with high stiffness (due to PLA) and toughness (due to PCL) are very promising materials for medical applications, namely for the bone tissue engineering.

Development of tailored high-performance and durable electrocatalysts for advanced PEM fuel cells

A family of novel carbon materials with intermediate surface area and varying morphology and surface chemistry were used to prepare Pt/C catalysts by two different preparation procedures; a chemical impregnation method and a microwave-assisted polyol method. The catalysts were thoroughly characterized, and their electrochemical performance and stability were investigated with rotating disc electrode (RDE) cyclic voltammetric (CV) measurements. The intermediate-surface-area carbon supports gave catalysts with much greater support stability than a widely used standard catalyst. The novel catalysts had lower electrochemical surface area than the reference, but their specific electrocatalytic activity towards the oxygen-reduction reaction (ORR) was much higher, and some of them also featured higher mass-specific ORR activity than the reference. The series of catalysts prepared by the microwave-assisted polyol method featured smaller Pt nanoparticles and higher activities than those prepared by impregnation. On the other hand, the impregnated catalysts showed better durability of the Pt particles. The most promising catalysts were selected and elaborated in further optimized preparation procedures to obtain quantities sufficient for their use in proton-exchange membrane fuel cells (PEMFCs).

Miscanthus stem fragment – Reinforced polypropylene composites: Development of an optimized preparation procedure at small scale and its validation for differentiating genotypes

The production of ligno-cellulosic biomass-based composites requires the development of new methodologies to evaluate the reinforcement potential of a given biomass, such as miscanthus studied in the work. Miscanthus stems from thirteen genotypes were broken into elongated fragments and mixed with polypropylene composites in an internal mixer. The aim is to find the best protocol able to discriminate miscanthus genotypes for their reinforcement capability. The following process parameters were optimized in order to maximize the reinforcement effect of the stem fragment filler: mixing parameters (mixing time, rotor speed and chamber temperature), temperature, fragment content, size and length distributions and coupling agent. The relationship between the process parameters and the mechanical properties of composites were analyzed to evaluate the influence of genotype on reinforcement performance, showing the robustness of the protocol in effectively discriminating genotypes according to their reinforcing capacity.

Soy-based adhesive cross-linked by melamine–glyoxal and epoxy resin

To develop a soy-based adhesive with good water resistance, non-toxic melamine–glyoxal resin (MG) prepared in the laboratory was used as a cross-linker of soy-based adhesive. The FT-IR and ESI-MS results showed that there was a reaction between melamine and glyoxal. The resulted –CH–OH– groups could be the possible reactive groups for the cross-linking of soy-based adhesive. The wet shear strength of soy-based plywood indicated that the water resistance of soy adhesive cross-linked by MG improved with respect to that with no cross-linker, although it was not good enough to satisfy the relative standard. With the optimized preparation procedures for plywood, specifically, press temperature 180 °C, press time 3 min and resin loading 280 g m−2, type I soy-based plywood could be prepared with a hybrid cross-linker, namely 12%MG + 2% epoxy resin (EPR). The DSC results showed that the reaction between soy-based adhesive and the hybrid cross-linker MG + EPR was very complex.

Treatment of Parkinson's disease using cell transplantation.

The clinical trials with intrastriatal transplantation of human fetal mesencephalic tissue, rich in dopaminergic neurons, in Parkinson's disease (PD) patients show that cell replacement can work and in some cases induce major, long-lasting improvement. However, owing to poor tissue availability, this approach can only be applied in very few patients, and standardization is difficult, leading to wide variation in functional outcome. Stem cells and reprogrammed cells could potentially be used to produce dopaminergic neurons for transplantation. Importantly, dopaminergic neurons of the correct substantia nigra phenotype can now be generated from human embryonic stem cells in large numbers and standardized preparations, and will soon be ready for application in patients. Also, human induced pluripotent stem cell-derived dopaminergic neurons are being considered for clinical translation. Available data justify moving forward in a responsible way with these dopaminergic neurons, which should be tested, using optimal patient selection, cell preparation and transplantation procedures, in controlled clinical studies.