Optimization Of Solid Lipid Nanoparticles Research Articles

Optimization of solid lipid nanoparticles prepared by a single emulsification-solvent evaporation method.

This data article contains the data related to the research article “Characterization, biorecognitive activity and stability of WGA grafted lipid nanostructures for the controlled delivery of rifampicin” (Pooja et al. 2015) [1]. In the present study, SLN were prepared by a single emulsification-solvent evaporation method and the various steps of SLN preparation are shown in a flow chart. The preparation of SLN was optimized for various formulation variables including type and quantity of lipid, surfactant, amount of co-surfactant and volume of organic phase. Similarly, effect of variables related to homogezation, sonication and stirring processes, on the size and surface potential of SLN was determined and optimized.

Solid lipid nanoparticles of ondansetron HCl for intranasal delivery: development, optimization and evaluation

The present investigation deals with the development and statistical optimization of solid lipid nanoparticles (SLNs) of ondansetron HCl (OND) for intranasal (i.n.) delivery. SLNs were prepared using the solvent diffusion technique and a 2(3) factorial design. The concentrations of lipid, surfactant and cosurfactant were independent variables in this design, whereas, particle size and entrapment efficiency (EE) were dependent variables. The particle size of the SLNs was found to be 320-498 nm, and the EE was between 32.89 and 56.56 %. The influence of the lipid, surfactant and cosurfactant on the particle size and EE was studied. A histological study revealed no adverse response of SLNs on sheep nasal mucosa. Transmission electron microscopic analysis showed spherical shape particles. Differential scanning calorimetry and X-ray diffraction studies indicated that the drug was completely encapsulated in a lipid matrix. In vitro drug release studies carried out in phosphate buffer (pH 6.6) indicated that the drug transport was of Fickian type. Gamma scintigraphic imaging in rabbits after i.n. administration showed rapid localization of the drug in the brain. Hence, OND SLNs is a promising nasal delivery system for rapid and direct nose-to-brain delivery.

Formulation development and systematic optimization of solid lipid nanoparticles of quercetin for improved brain delivery

This study aims at formulating solid lipid nanoparticles (SLNs) of quercetin, a natural flavonoid with established antioxidant activity, for intravenous administration in order to improve its permeation across the blood-brain barrier into the CNS, and eventually to improve the therapeutic efficacy of this molecule in Alzheimer's disease. The SLNs of quercetin were formulated using Compritol as the lipid and Tween 80 as the surfactant through a microemulsification technique, and optimized employing a 3(2) central composite design (CCD). Selection of the optimized SLN formulation, using brute-force methodology and overlay plots, was based on its efficiency of entrapping quercetin inside the lipophilic core, particle size, surface charge potential and ability of the SLNs to release the entrapped drug completely. The optimized formulation was subjected to various in-vivo behavioral and biochemical studies in Wistar rats. The optimized formulation exhibited a particle size of less than 200 nm, 85.73% drug entrapment efficiency and a zeta potential of 21.05 mV. In all the in-vivo behavioral and biochemical experiments, the rats treated with SLN-encapsulated quercetin showed markedly better memory-retention vis-à-vis test and pure quercetin-treated rats. The studies demonstrated successful targeting of the potent natural antioxidant, quercetin, to brain as a novel strategy having significant therapeutic potential to treat Alzheimer's disease.

Development and optimization of solid lipid nanoparticles of amikacin by central composite design

Solid lipid nanoparticles (SLNs) have been studied as a drug-delivery system for the controlling of drug release. These colloidal systems have many important advantages, such as biocompatibility, good tolerability, and ease of scale-up. In the preparation of SLNs, many factors are involved in the characteristics of the particles, such as particle size, drug loading, and zeta potential. In this study, fractional factorial design was applied to examine which variables affect the physicochemical properties of amikacin SLNs. Study was continued by a statistical central composite design (CCD) to minimize particle size and maximize drug-loading efficiency of particles. The results showed that three quantitative factors, including the amount of lipid phase, ratio of drug to lipid, and volume of aqueous phase, were the most important variables on studied responses. The best predicted model for particle size was the quadratic model, and for drug-loading efficiency, was the linear model without any significant lack of fit. Optimum condition was achieved when the ratio of drug to lipid was set at 0.5, the amount of lipid phase at 314 mg, and the volume of aqueous phase at 229 mL. The optimized particle size was 149 ± 4 nm and the drug-loading efficiency 88 ± 5%. Polydispersity index was less than 0.3. The prepared particles had spherical shape, and the drug release from nanoparticles continued for 144 hours (6 days) without significant burst effect.

Development and Statistical Optimization of Solid Lipid Nanoparticles of Simvastatin by Using 23 Full-Factorial Design

The objective of this study was to develop solid lipid nanoparticles (SLNs) of simvastatin and to optimize it for independent variables (amount of glycerol monostearate, concentration of poloxamer, and volume of isopropyl alcohol) in order to achieve desired particle size with maximum percent entrapment efficiency (% EE) and percent cumulative drug release (% CDR). To achieve our goal, eight formulations (F(1)-F(8)) of SLNs were prepared by solvent injection technique and optimized by 2(3) full-factorial design. The design was validated by extra design checkpoint formulation (F(9)), and the possible interactions between independent variables were studied. The responses of the design were analyzed using Design Expert 7.1.6. (Stat-Ease, Inc, USA), and the analytical tools of software were used to draw Pareto charts and response surface plots. On the basis of software analysis, formulation F(10) with a desirability factor of 0.611 was selected as optimized formulation and was evaluated for the independent parameters. Optimized formulation showed particle size of 258.5 nm, % EE of 75.81%, with of 82.67% CDR after 55 h. The release kinetics of the optimized formulation best fitted the Higuchi model, and the recrystallization index of optimized formulation was found to be 65.51%.

Characterization and formulation optimization of solid lipid nanoparticles in vitamin K1 delivery

Background: Solid lipid nanoparticle (SLN) systems have been applied to various drugs and delivery routes. Vitamin K1 is an important cofactor for maintaining hemostasis and preventing hemorrhage. Method: Vitamin K1-loaded SLNs are systematically being developed by optimizing triglycerides and lipophilic and hydrophilic surfactants based on the size and stability of the resulting SLNs. Concentrations of the surfactants, Myverol and Pluronic, were optimized by a central composite design and response surface methodology. Vitamin K1 (phylloquinone) was used as a lipophilic drug in the SLN system to evaluate the potential for oral delivery. Results: Vitamin K1-loaded SLNs had a mean size of 125 nm and a zeta potential of −23 mV as measured by photon correlation spectroscopy. The prepared SLNs were examined by differential scanning calorimetry and transmission electron microscopy and found to have an imperfect crystalline lattice and a spherical morphology. Effects of ultrasonication duration and drug load on the particle size and entrapment efficiency of the SLNs were also evaluated. Conclusion: More than 85% of the vitamin K1 was entrapped in SLNs when the payload was <5%. The vitamin K1 in SLNs was stable for a 54-h duration in simulated gastric and intestinal fluids. The particle size and vitamin K1 entrapped in the SLN were stable after 4 months of storage at 25°C. The results demonstrated that SLNs prepared herein can potentially be exploited as carriers for the oral delivery of vitamin K1.

Formulation and optimization of solid lipid nanoparticles of buspirone HCl for enhancement of its oral bioavailability

Solid lipid nanoparticles (SLNs) of buspirone HCl as a water-soluble drug were prepared by emulsification-evaporation, followed by the sonification method. A preliminary screening of the most effective parameters on the production of nanoparticles by a Taguchi L8 orthogonal array showed that the lipid type, surfactant percentage, speed of homogenizer, and acetone:dichloromethane (DCM) ratio had a significant effect on particle size. In the next step, the lipid was fixed on cetyl alcohol, surfactant on Tween 20, lecithin:lipid weight ratio on 20:70, sonication time on 30 seconds, and the other effective, independent factors aforementioned were studied each at three levels by a three-factor, three-level Box-Behnken design. The percentage of drug entrapment, mean particle-size diameter, and zeta potential were studied as the responses. Contour plots were constructed to further elucidate the relationship between the independent and dependent variables. A pharmacokinetic study was conducted in male Wistar rats after oral administration of 15 mg.kg−1 buspirone in the form of free drug or SLNs. The optimized SLNs had aq particle size of 345.7 nm, loading efficiency of 32.8%, and zeta potential of −6.8 mV. Buspirone released about 90% during 4.5 hours in vitro. It was found that the relative bioavailability of the drug in SLNs was significantly increased, compared to that of the drug solution.

Development and optimization of solid lipid nanoparticles of amikacin by central composite design

Development and optimization of solid lipid nanoparticles of amikacin by central composite design