Optimal Conditions Research Articles

Optimum Thermal Treatment for Removing Antibiotic Resistance Genes and Retaining Nutrients in Poultry Broiler Manure

Poultry broiler manure is a reservoir of antibiotic resistance genes (ARGs), antibiotics, organic carbon, and plant nutrients. However, its direct application leads to spread of ARGs in agricultural fields, causing public concerns. It is thus crucial to identify optimum heating conditions that remove ARGs while retaining nutrients. This study examined the effects of heating temperatures (100-500oC) and durations (30, 120 and 240min) on the removals of ARGs and antibiotics from poultry broiler manure and nutrient retention. The results showed that the poultry broiler manure contained a total of 211 ARG subtypes, which were susceptible to temperature. The contents of ARGs and antibiotics decreased with increasing temperature. The temperature had a significant effect on the loss of available phosphorus (r = -0.893, P <0.01), while other nutrients had no significant loss. The results show that the heat treatment at 110°C for 240min maximized the removals of ARGs while the loss of nutrients was minimized. Under these optimum conditions, all ARGs and antibiotics (e.g., oxytetracycline, tetracycline, doxycycline, tilmicosin, tylosin, sulfamethazine, and sulfadiazine) were removed while 91.98% of total carbon, 99.89% of total nitrogen, 92.38% of total phosphorus, 50.10% of available phosphorus, 99.96% of total potassium, and 95.02% available potassium were preserved. These findings suggest that heat treatment at 110oC for 240min could be an effective and affordable approach to safe use of poultry broiler manure.

Efficient removal of cationic dyes by a bivanadyl capped, highly reduced Keggin polyoxometalate through flocculation

Flocculation is widely applied for dye wastewater treatment, due to its low cost, high efficiency and convenient operation. However, finding novel flocculant with high performance and low cost is still a challenge. Therefore, a fully characterized bivanadyl capped, highly reduced Keggin polyoxometalate (Et3NH)5[PMoV6MoVI6O40(VIVO)2] (PMoV2) was explored as flocculant for the treatment of simulated cationic dye wastewater. The effect of initial pH, PMoV2 dosage, and concentrations of dyes and inorganic salts on the flocculation rate of methylene blue (MB)/ crystal violet (CV)/rhodamine B (RhB) was investigated. Under the optimum conditions, the flocculation rates of MB, CV and RhB were 99.7%, 99.8% and 99.7% in 5min, respectively. In addition, PMoV2 and dyes could be easily recovered from flocs. PMoV2 exhibited high selectivity for CV in the binary systems of CV-MB and CV-MO. Even after five recycling tests, PMoV2 still kept high flocculation rate of MB/CV/RhB. The possible flocculation mechanisms for MB/CV/RhB single system, and MB-CV and MO-CV binary systems were charge neutralization, charge neutralization and π-π interaction, and charge neutralization and electrostatic interaction, respectively. PMoV2 was better than the reported flocculants in the respect of easy availability and operation conditions, reusability and high flocculation rate. The cost effectiveness, eco-friendly nature and excellent flocculation performance in individual and binary dye systems made PMoV2 competitive in the field of water environment remediation and material development. This is the first report about the flocculation activities of bivanadyl capped, highly reduced Keggin polyoxometalate.

Modification and mechanistic study of fluid/fluid and carbonate rock/fluid interfaces using a glycolipid biosurfactant from an indigenous strain of Gordonia terrae for MEOR applications

To clarify the mechanism of the interface behavior between carbonate surface/biosurfactant solution/oil systems, the interfacial tension (IFT), surface wettability, spreading coefficient (SC), and capillary number were investigated with regard to the synergistic effects of a biosurfactant from an indigenous Gordonia terrae strain (isolated from an Iranian oil reservoir), formation water salinity, and pH using response surface methodology (RSM-CCD). According to the analysis of variance results, the process effectively depicted by the quadratic model demonstrated statistical significance in terms of the responses of IFT, wettability alteration, and SC, which were significantly affected by biosurfactant concentration. The optimal conditions were 0.260 g/L biosurfactant, 36.202 g/L salinity, and a pH of 5.9. Accordingly, the quadratic model was verified using the estimated optimal parameters, thereby confirming the accuracy of the model in which a strongly water-wet surface (contact angle change from 159° to 31°) and IFT reduction (from 23.96 to 1.26 mN/m) resulted in an SC of near-zero value (−0.18) and 25 % recovery of oil during the imbibition experiments after secondary water flooding. The desorption of the polar components of crude oil from the dolomite rock surface was also investigated through determining the un-coverage ratios of the elements using energy dispersive X-ray microanalysis and characterization. Although the solutions containing biosurfactants contributed to the alteration of the rock surface wettability, their performance strongly depended on the pH and salinity, resulting in different desorption ratios. The desorption of approximately 40 % of the adsorbed organic compounds from the carbonate surface was a critical limiting factor affecting the surface properties of the rock, and was responsible for altering the wettability to water-wet conditions. The results of this study are expected to contribute to the development of effective biosurfactant-flooding techniques for MEOR.

Optimal carbofuran degradation via CWPO in NOM-doped water by a framework Cu-doped aluminate perovskite catalyst derived from aluminum saline slags

This study is the first to propose the synthesis of LayAl1–xCuxO3–δ perovskite catalysts using Al recovered from acid leaching of saline slags. The effect of parameters such as the La/Al molar ratio was explored during the synthetic process. A suite of characterization techniques—including XRF, XRD, N2 adsorption, H2-TPR, FTIR, TGA-DTA, TEM, SEM, EDX, and XPS—confirmed the successful synthesis of high-purity (up to 90 %) perovskites with La and O vacancies, and a high concentration of Cu(I) active sites dispersed within the perovskite lattice. The best catalyst was used to optimize the degradation of carbofuran (CBF) in water doped with synthetic dissolved natural organic matter (NOM) using the Fenton-like catalytic wet peroxide oxidation (CWPO) approach. The effects of catalyst concentration, H2O2 dose, and pH on catalytic performance were investigated. Degradation, mineralization (COD removal), and H2O2 consumption were maximized, while Cu leaching was minimized using a statistical desirability function for multiple responses. Optimal conditions were found to be a catalyst concentration (mg Cu/mg H2O2) of 0.234 (2.0 g L–1), an H2O2 dose of 73.3 % (0.73 times the stoichiometric dose for full COD mineralization), and a remarkable circumneutral pH of 6.2. Under these conditions, degradation reached 94.1 %, and COD mineralization was 51 % under room temperature. Notably, the perovskite catalyst exhibited remarkable stability during reuse in up to three cycles, as demonstrated by the low Cu leaching (<1.30 mg L–1).

Type-II heterojunction Se-g-C3N4/ZnO coupled MnCo2O4 photocatalyst for enhanced levofloxacin hydrochloride degradation activated by peroxymonosulfate

The advanced oxidation process induced by photocatalysis under visible light undoubtedly possesses greater application potential and cost-effectiveness due to the high excitation energy supply costs. Here, we proposed a novel Type-II heterojunction Se-g-C3N4/ZnO (Se-CN/ZnO) and MnCo2O4 (MCO) photocatalyst for the efficient degradation of levofloxacin hydrochloride (LEV) activated by peroxymonosulfate (PMS) under sunlight. Analysis results confirmed the oxidation process was executed by Se-CN/ZnO synergistic MCO-activated PMS for the responsive degradation of LEV, achieving a removal efficiency greater than 98.6 % within 15 min (kinetic rate constant Kobs = 0.299 min−1), under optimal conditions ([Se-CN/ZnO (300 °C)]0 = 46 mg, [MCO]0 = 1.6 mg, [PMS]0 = 0.27 mM, [Aeration rate]0 = 146 mL/min, pH = 5.5). Effective interfacial transfer and spatial segregation of the photogenerated electron-hole were attributed to the stabilized Type-II energy band structure of Se-CN/ZnO, the rapid cyclic redox of metal ions Mnn+(n = 2,3,4) and Com+(m = 2,3) promoted the activation of PMS reduction of LEV through synergistic action of various endogenous substances. Analysis of the contribution of reactive oxygen species by electron paramagnetic resonance substantiated the dominant role of ·OH and O2·-, and the superiority of the degradation process was further validated with the analysis of the non-toxic and ecological safety characteristics of intermediates. The recommended method of eco-friendly and stable catalytic performance of LEV has engineering application prospects that are incomparable to many publicly available treatment methods.

MXene/TiO2 NAs on CC flexible electrode for electrocatalytic tigecycline degradation: Performance, Mechanistic insights, and toxicological assessment

In this study, a composite electrode (MXene/TiO2 NAs@CC) based on TiO2 nanotube arrays (NAs) and two-dimensional MXene-coated carbon cloth (CC) was prepared. The electrode greatly improved the catalytic activity by capturing protons through the abundant active sites of TiO2 nanotube arrays and promoting proton reduction with the high conductivity of MXene. Moreover, the composite electrode possessed the largest specific surface area (9.1660 m2·g−1) according to the results of the BET test. Under optimal conditions, the composite electrode degraded tigecycline (TGC) up to 86.66 % in 20 min. Furthermore, the electrocatalytic performance was not affected after 10 cycling experiments and 60 days of exposure to air, indicating its excellent stability. In addition, the cathodic co-catalytic reaction mechanism involving anode ·OH, HClO, and cathode H* was proposed. The degradation pathways of TGC and the toxicity of possible intermediates were also analyzed. Finally, a two-stage continuous wastewater reactor with high efficiency and low consumption (90.46 % removal rate, 0.061 kWh/m3) was designed. This study provides a new idea for designing an electrocatalytic reactor with high efficiency, stability, and low consumption, enriching the field of electrocatalytic treatment strategies for antibiotic wastewater. It is of great significance for the protection of the water environment and human health.

A novel strategy for waste activated sludge treatment: Recovery of structural extracellular polymeric substances and fermentative production of volatile fatty acids

Structural extracellular polymeric substances (SEPS) as valuable biopolymers, can be extracted from waste activated sludge (WAS). However, the extraction yield is typically low, and detailed information on SEPS characterizations, as well as proper treatment of the sludge after SEPS extraction, remains limited. This study aimed to optimize the conditions of heating-Na2CO3 extraction process to increase the yield of SEPS extracted from WAS. Subsequently, SEPS were characterized, and, for the first time, insights into their protein composition were uncovered by using proteomics. A maximum SEPS yield of 209 mg/g volatile solid (VS) was obtained under optimal conditions: temperature of 90°C, heating time of 60 min, Na+ dosage of 8.0 mmol/g VS, and pH required to precipitation of 4.0, which was comparable to that from the aerobic granular sludge reported in literature. Proteomics analysis unveiled that the proteins in SEPS primarily originated from microorganisms involved in nitrogen fixation and organic matter degradation, including their intracellular and membrane-associated regions. These proteins exhibited various catalytic activities and played crucial roles in aggregation processes. Besides, the process of SEPS extraction significantly enhanced volatile fatty acid (VFA) production during the anaerobic fermentation of residual WAS after SEPS extraction. A maximum VFA yield of 420 ± 14 mg COD/g VSadded was observed in anaerobic fermentation of 10 d, which was 77.2 ± 0.1% higher than that from raw sludge. Mechanism analysis revealed that SEPS extraction not only improved WAS disintegration and solubilization but also reduced the relative activity of methanogens during anaerobic fermentation. Moreover, SEPS extraction shifted the microbial population during anaerobic fermentation in the direction towards hydrolysis and acidification such as Fermentimonas sp. and Soehngenia sp. This study proposed a novel strategy based on SEPS extraction and VFA production for sludge treatment, offering potential benefits for resource recovery and improved process efficiency.

Simultaneous electrochemical removal of three microcystin congeners and sulfamethoxazole in natural water

Microcystins (MCs), frequently detected in freshwater ecosystems, have raised significant human health and ecological concerns. New approaches are being developed to control and remove MCs. In this study, we examined factors influencing the efficacy of electrochemical oxidation as a means of control. Anode material (Pt/Ti, Ta2O5-IrO2/Ti, SnO2-SbO2/Ti, boron-doped diamond (BDD)/Si), anode surface area ratios and solution volumes, initial pollutant concentrations, and the co-existing antibiotic sulfamethoxazole (SMX) were investigated. MCs and SMX were dissolved in filtered Taihu Lake water to simulate the natural aquatic environment. The results showed that non-active anodes, lower initial concentration of MC, larger surface area ratio of anode to cathode, and smaller ratio of reaction solution volume to anode surface area could promote the degradation target pollutants. Under optimal conditions in this study, the degradation rates of MC-LR, MC-YR, MC-RR, and SMX each reached more than 90% within 6 hours, and the removal efficiency of MC-YR was the highest among three congeners. The effect of SMX on the degradation of MC congeners depended mainly on their concentration differences, such that when the initial concentration of SMX was one to two orders of magnitude lower than microcystin, the presence of SMX would promote the degradation of MCs. In contrast, when the initial concentration of SMX was higher than that of microcystin by approximately an order of magnitude, sulfamethoxazole would inhibit the degradation of MCs by between 4.6% and 24.5%. Ultra-high-performance liquid chromatography tandem mass spectrometry analysis revealed that the three MC congeners were electrochemically degraded through aromatic ring oxidation, alkene oxidation, and bond cleavage on the ADDA (3-amino-9-methoxy-2,6,8-trimethyl-10-phenyldeca-4,6-dienoic acid) side chain. Notably, the removal of MCs was accompanied by a decline in the hardness of the reaction water. This study provided insights into electrochemical degradation of microcystins and antibiotics in natural water, offering suggestions for its practical application.

Study on the unique separation effect of emulsion in the stirring-induced turbulent flow field

Much attention has been gained to treat organic pollution dominated by oil pollutants in water with the frequent discharge of wastewater in industries. Liquid–liquid emulsion is a typical existence form of water and oil pollutants. The relative stable flow field is a necessary condition to separate the emulsion, while turbulence of the flow field is required for homogeneous mixing. For centuries, stirring-induced turbulent flow has been used for mixing, with a limited number of separation cases achieved by the stable part of the container at low Reynolds numbers (Re). In this study, the separation of liquid–liquid emulsions in a fully turbulent system for Reynolds number values above 10,000 was observed for the first time. Besides the turbulent flow influenced by the stirring speed, the additional dispersed phase, which was the same as the emulsified dispersed phase, played a critical role in the separation performance. The turbidity of oil-in-water emulsion could be decreased to less than 5 NTU (nephelometric turbidity unit) from 500 NTU under the optimal conditions in this study, with a separation efficiency of over 99%. This peculiar and wonderful characteristic of the turbulent flow and the study of the parameters and constraint conditions for separation may extend the application field of the turbulent flow field from conventional mixing to oil pollutants separation from water in environmental engineering.

On-site extraction of phenoxycarboxylic acid herbicides in environmental waters utilizing monolith-based in-tip microextraction technique

On-site extraction plays a significant role in the reliable quantification of strong polar phenoxycarboxylic acid herbicides (PCAs) in aqueous samples. In current study, a new technique for the field sample preparation of PCAs was developed by means of three channels in-tip microextraction device (TCIM). To capture PCAs effectively, an extraction phase based on monolith (EPM) using vinylimidazole and divinylbenzene/ethylene dimethacrylate as monomer and cross-linkers, respectively, was in-situ synthesized in pipette tips. The EPM fabricated at optimal conditions were characterized by a series of techniques and employed as the adsorbent of TCIM for the on-site extraction of PCAs. The adsorption isotherm was studied so as to inspect the extraction behaviors of EPM towards PCAs. Results revealed that the proposed EPM/TCIM presented satisfactory extraction performance towards PCAs through multiple interactions. The enrichment factors and adsorption capacity were 74-277 and 20 mg/g, respectively. Under the most beneficial extraction parameters, the developed EPM/TCIM was successfully employed to on-site extract PCAs, and then combining with HPLC equipped with diode array detector to monitor trace PCAs in actual waters. The limits of detection (LODs) towards investigated PCAs varied from 0.071 μg/L to 0.30 μg/L. In addition, the accuracy of established approach was inspected with documented method. Compared with existing lab-based sample preparation approaches, the introduced field sample preparation technique exhibits some merits such as avoidance of transporting large volume of water, prevention of analytes loss during sampling procedure, less usage of organic solvent and achievement of satisfactory efficient in sample preparation.

Investigation into the purification and regeneration of rare earth polishing powder waste via continuous solid-phase conversion

The concentration of rare earth elements (lanthanum, cerium, and praseodymium) within rare earth polishing powder waste (REPPW) typically exceeds 50 %, with the majority of impurities comprised of silicon and aluminum-related compounds. Transforming REPPW into recycled rare earth polishing powders that adhere to polishing standards in an eco-friendly and economically viable way presents a significant challenge in the industry. Traditional acid or alkaline processes predominantly recover rare earth elements as oxides, which are underutilized due to their high costs. Considering the varying forms of impurities and rare earth compounds found in REPPW, this research introduces a novel physicochemical decontamination and continuous chemical transformation process aimed at producing regenerated rare earth polishing powders. Under optimal conditions, the physicochemical two-step decontamination process achieved a rare earth recovery rate surpassing 92 %, while silicon and aluminum removal rates reached 86.12 %. During the continuous chemical transformation of REPPW, the rare earth phases in an alkaline setting followed the sequence REOF (CeO2) → RE(OH)3 → RECO3OH→RECO3F→CeLa2O3F3(CeO2), which not only facilitated phase reorganization but also enhanced the particle surface structure. Notably, these chemical transformations did not disrupt the rare earth distribution; instead, they indirectly boosted product purity and uniformly dispersed within the regenerated polishing powder particles, thereby improving polishing efficiency. Consequently, the adoption of this innovative regeneration process for polishing powders holds substantial importance for the sustainable utilization of rare earth resources.

Comprehensive characterization of active components in Salvia miltiorrhiza using polarity-partitioned two-dimensional liquid chromatography coupled with mass spectrometry

Salvia miltiorrhiza, a widely used traditional Chinese medicine, contains a complex matrix of hydrophobic diterpenoids and hydrophilic phenolic acids, presenting significant challenges in comprehensive analysis. In this study, an online polarity-partitioned two-dimensional liquid chromatography coupled with mass spectrometry (2D-LC-MS) method was developed for comprehensive analysis of both lipophilic and hydrophilic active components in Salvia miltiorrhiza. The method integrated hydrophilic interaction liquid chromatography (HILIC) and reversed-phase liquid chromatography (RPLC), facilitating the efficient separation of compounds across a wide range of polarities. An online dilution strategy was implemented, minimizing sample loss and enhancing the method's utility for quality control and chemical characterization of complex herbal matrices. Compared with other LC methods, this approach significantly improved analyte coverage, resolution, and analysis efficiency. Under optimal conditions, 150 active components were successfully identified, including 33 compounds newly discovered in Salvia miltiorrhiza. Additionally, the validated online method was applied to the quantitative determination of 16 quality markers of Salvia miltiorrhiza from different sources. The results demonstrated the online method's potential as a superior alternative to existing techniques, offering broader applicability in traditional Chinese medicine research.

An innovative process for clean ammonium-free vanadium precipitation and one-step preparation of vanadium dioxide based on hydrothermal enhancement of organic alcohols

As a transition metal oxide, VO2 has excellent optical and electrical properties and is widely used in many fields. The production of VO2 by the reduction of NH4VO3 and V2O5 will inevitably produce ammonia–nitrogen wastewater and NH3 emission during the production of NH4VO3 and V2O5, which will cause serious environmental pollution and will increase economic costs. The large-scale and low-cost synthesis of VO2 still faces great challenges. In this paper, VO2(B) was successfully prepared by a one-step hydrothermal method using NaVO3 as the vanadium source and CH3CH2OH as the reducing agent, and the optimal conditions for vanadium precipitation are as follows: vanadium concentration = 30 g/L, CH3CH2OH dosage = 20 % (percentage of solution volume), initial pH = 1, reaction temperature = 220 °C, reaction time = 12 h. The vanadium precipitation efficiency under the optimal conditions could reach 98.93 %, and the purity of VO2(B) could reach 98.59 %. The precipitation products were characterized by XRD, TG, FTIR, XPS, and SEM-EDS. The mechanism of VO2(B) preparation by ethanol reduction was proposed. This process is characterized by green, clean, and high efficiency. At the same time, the vanadium precipitation effect and vanadium precipitation products of various alcohols were studied to provide technical and theoretical support for the preparation of VO2(B).

Preparation of magnesium potassium phosphate cement from magnesite tailings under lower calcination temperature

The identification of a more economical source of magnesium, coupled with reduced preparation costs, is essential for enhancing the competitiveness of magnesium potassium phosphate cement (MKPC) production. This study explores the utilization of magnesite tailings, waste materials produced during the mining and ore dressing process of magnesite, as raw materials for the preparation of low-cost dead-burnt magnesium oxide (MgO-T) at comparatively low calcination temperatures. The research demonstrated that impurities, specifically silicon and calcium, formed compounds with MgO during calcination, leading to the encapsulation of certain MgO particles. This encapsulation reduced both the specific surface area and hydration activity of the MgO. Despite the calcination temperature of 1100 °C being significantly lower than that of commercial dead-burnt MgO (MgO-C) at 1700 °C, MgO-T exhibited lower activity compared to MgO-C, which rendered it more suitable for the production of MKPC. Under optimal conditions, characterized by a molar ratio of magnesium to phosphorus (M/P) of 3, a borax retarder content of 15%, and a water-cement ratio of 0.15, the MKPC prepared using MgO-T demonstrated an initial setting time exceeding 60min and achieved a compressive strength of up to 79.6MPa. XRD and microstructural analyses revealed that struvite-K was the primary strength phase; however, the porosity of the specimens had a more pronounced effect on strength. By producing lower activity MgO at reduced calcination temperatures, this method obviates the need for complex purification processes when utilizing magnesite tailings, thereby decreasing the costs associated with MKPC preparation and presenting promising applications for the future.

Novel 3D plate-like g-C3N4/BiOCl heterojunction as a highly efficient photocatalyst for the degradation of carbofuran in wastewater under visible light irradiation

The g-C3N4/BiOCl (gCN-BCl) heterojunction photocatalyst was synthesized using a low-temperature precipitation method for effective photocatalytic degradation of carbofuran (CBF). All gCN-BCl composites demonstrate greater efficacy in removing CBF compared to its individual constituents. The synergistic effect of incorporating the 0D structured BiOCl onto the 2D structured g-C3N4 was comprehensively examined using various microscopic, X-ray, and spectroscopic analytical techniques. Additionally, optical and photoelectrochemical analyses were conducted. The findings validated that the interaction between the two semiconductors at the heterointerfaces enhanced remarkable physical and structural stability, promoted high charge separation and transfer properties, and improved photocatalytic degradation. Under optimal conditions, 5-gCN-BCl (0.25 g/L) achieved a CBF (5 mg/L) removal efficiency of 95.7 % under visible light irradiation of 120 min, achieving 3.1- and 5.9-times higher degradation rate than the pure BiOCl and g-C3N4, respectively. The radical trapping experiments indicated that the h+ and •O2− were the primary reactive species involved in the CBF degradation. Furthermore, the potential toxicity of CBF and its intermediates was assessed, revealing that the photocatalytic degradation process significantly lowered the ecotoxicity of pesticide wastewater. The potency of 5-gCN-BCl was also evaluated in tap water and real wastewater samples, with CBF degradation efficiencies of 85.8 %, 47.6 %, and 38.7 % in tap water, municipal, and pesticide industry wastewater, respectively. Additionally, artificial neural network (ANN) modeling was employed to predict and optimize the photocatalytic degradation process, providing further insights into the system’s performance. The outcomes of this work offer valuable insights into the development of heterojunction photocatalysts with superior stability and efficacy for eliminating pesticides from water bodies.

Extraction of rhodium from supported liquid-phase hydroformylation catalysts with supercritical carbon dioxide

The continuous extraction of the rhodium inventory in supported liquid-phase (SLP) catalytic materials utilized in the hydroformylation (HyFo) of 1-butene was investigated by supercritical carbon dioxide (scCO2). Optimization of extraction efficiency involved varying parameters such as temperature (90 and 120 °C), pressure (10, 20 and 30 MPa), and the addition of methanol as a polar co-feed to the extraction medium (0–20 vol%). The results underscored the critical role of methanol in facilitating extraction, as experiments employing pure scCO2 yielded no rhodium recovery. Furthermore, extraction performance demonstrated sensitivity to temperature and pressure adjustments during the process. Notably, the use of 10 vol% methanol at 120 °C and 30 MPa achieved complete rhodium extraction from the grained SLP materials, which was identified as the optimum extraction condition. This study highlights the potential for scaling up in-situ rhodium extraction processes within HyFo production plants based on SLP catalysts, emphasizing significant implications for industrial applications.

Performance of a novel waste heat-powered ionic liquid-based CO2 capture and liquefaction system for large-scale shipping

In this work, we proposed a novel CO2 capture and liquefaction system for large-scale shipping using ionic liquid as capture solvent. By utilizing the waste heat of the exhaust gas and jacket cooling water from the ship’s engine as well as the residual pressure energy of the N2-O2 mixture from the CO2 absorption and desorption process, the system’s net energy consumption has been significantly reduced. We established the thermodynamic model of the system and investigated the effect of 10 primary system operational parameters on system performance with 3 different ionic liquids as CO2 capture solvent. The results demonstrated that the system with [DEME][TF2N] as the CO2 capture solvent had the best system performance. In addition, we performed a multi-parameter optimization of the system using simulated annealing algorithm with net energy consumption as the optimization objective and the minimal net energy consumption is 0.467 GJ/tCO2. Compared to the CO2 capture system that do not utilize waste heat and residual pressure energy, the net energy consumption was reduced by 57.29 % under optimal operational conditions which proves that the novel system significantly reduces the energy consumption of the CO2 capture and liquefaction process.

Computational and experimental investigation on functional monomer selection for a novel molecularly imprinting polymer of remdesivir

Molecularly-imprinted polymers (MIPs) are a sample preparation technique with a functional cavity that can rebind the same or similar analyte to the template. It also can increase the selectivity of the analytical method. Computational approaches are capable of making predictions about the most optimal synthesis conditions, including the most appropriate monomers and solvents. This study used the DFT method, GFN2-xTB, and molecular dynamics simulation to predict MIP synthesis’s best functional monomer, solvent, and stoichiometric ratio. Remdesivir (RMD), used as a template, has also never been developed to be made as MIP. The monomers were acrylic acid (AA), 2-hydroxyethyl methacrylate (HEMA), and acrylamide (AM). Laboratory testing, association constant, and Job plot analysis are carried out to confirm the results of computational tests. The polymer was synthesized using precipitation and characterized using SEM, FTIR, and TGA. The adsorption capacity was evaluated in two different solvents, i.e. acetonitrile (ACN) and water: ACN=9: 1 (v/v). Computational study results identified acrylamide as the most interactive ligand with RMD as a template. The results of molecular dynamics simulations identify that the RMD: AM=1: 1 complex is the most stable in terms of the radial distribution function, hydrogen bond occupancy, and Gibbs bond free energy. The adsorption ability test results show that MIP 1 and MIP 2 have imprinting factor values of 1.36 and 1.15, respectively.

Simultaneous determination of ethylene oxide, 2-chloroethanol and ethylene glycol residues in medical device products by gas chromatography

A gas chromatography-based method was developed for the simultaneous and rapid determination of ethylene oxide (EO), 2-chloroethanol (ECH), and ethylene glycol (EG) residues in medical devices after EO sterilization. A sample weighing 2.5 g was added with 5 mL of ethanol as the extraction medium, and the residual substances in the sample were extracted at 40 ℃ for 4 h. The samples were separated on a DB-WAX capillary column (30 m×0.53 mm×1.0 μm) and determined using a hydrogen flame ionization detector. The temperature was maintained at 40 ℃ for 5 min, increased to 120 ℃ at a rate of 40 ℃/min, held for 5 min, and then increased to 200 ℃ at a rate of 6 ℃/min, held for 2 min. The flow rate of the nitrogen gas was 3 mL/min. The split ratio was 5∶1. The inlet and detector temperatures were 200 and 300 ℃, respectively. The changes in the chromatographic peak areas over time (0.5-10 h) under different temperatures (20, 30, 40, and 50 ℃) were investigated, and the optimal extraction condition was determined to be 40 ℃ for 4 h. In the experiments, quantification was performed using an external standard method. EO, ECH, and EG exhibited good peak shapes and separation effects as well as good linearity within their respective ranges. The linear correlation coefficients for EO, ECH, and EG were greater than 0.99. The limits of detection (LODs) for EO, ECH, and EG were in the range of 0.10-0.40 μg/g, and the limits of quantification (LOQs) were in the range of 0.30-1.20 μg/g. The average recoveries under different spiked levels were in the range of 91.08%-116.08%, and the relative standard deviations (n=6) were in the range of 0.56%-8.45%. EO, ECH, and EG residues were found to exist at different levels in the medical devices tested. In particular, disposable infusion sets must be paid careful attention. ECH and EG were not detected in disposable sterile medical devices made of non-polyvinyl chloride materials, which may be due to the fact that the products themselves did not contain chloride ions, they were not exposed to chlorine-containing substances during their production, sterilization, storage, transportation, use, etc. This study established a method to detect EO residues in disposable medical devices, and has the advantages of simple operation, excellent specificity, accurate quantification, and good reproducibility. It can simultaneously detect three residual substances in medical devices while meeting the actual detection requirements for EO, ECH, and EG residues. The method can be used to scientifically and effectively evaluate the risk of EO residues in single-use medical devices sterilized with EO, and will be helpful for improving the quality of medical devices, ensuring the safety of device use, and providing a reference for regulatory supervision and testing.

Bioremediation of soils contaminated with nicosulfuron by the bacterial complex ES58

Nicosulfuron residues in soil can be harmful to the environment. In this study, acid-producing Klebsiella oxytoca ES5 and Klebsiella grimontii ES8 were isolated to construct the ES58 bacterial complex. The culture medium was optimized using response surface methodology, nicosulfuron degradation by ES58 reached 97.21% in 96h. The optimal degradation conditions were: temperature: 25℃, pH 6, initial nicosulfuron concentration: 50mgL-1 and inoculum volume: 2%. The two individual strains and the bacterial complex were tested for the ability of nitrogen fixation, phosphorus solubilization, potassium decomposition and iron carrier production. The results revealed that both strains and the bacterial complex had the ability to promote the growth, with bacterial complex being more capable than the two individual bacterial strains. After 28 d of bioremediation of nicosulfuron-contaminated soil by ES58, degradation rate of nicosulfuron was 90.84% in the unsterilized soil. Furthermore, the remediation process restored the activities of catalase, invertase, dehydrogenase and urease in the soil. The ES5-specific gene budA and ES8-specific gene ldh were detected in the soil at the 28th day. ES58 exhibited different effects on the growth indexes of nicosulfuron-sensitive crops. The study provides a novel strategy for nicosulfuron degradation effective by constructing and utilizing bacterial complex.