Operation Of Microgrid Research Articles

Design and verification of monitoring system of DC microgrid based on Ethernet communication

AbstractReal‐time acquisition of microgrid (MG) operation data and remote control play a crucial role in the safe and stable operation of MG. A design scheme of monitoring system is proposed for the wind/photovoltaic/energy storage islanded direct current MG. The core controllers used in direct current MG system are programmable logic controller and digital signal processor. The monitoring system mainly adopts Ethernet communication, together with serial port communication mode Recommend Standard 232 (RS232) and Recommended Standard 485 (RS485) communication modes. A heterogeneous networking is built with controllers and data display instruments. Different monitoring interfaces are designed, the important information can be real‐time detected, collected and displayed. The multi‐energy and multi‐load dispatching operation control are realized according to scheduling operation plan. The parameters of the inverter can be adjusted, and the output voltage waveform and sinusoidal pulse width modulation waveform of the inverter can be measured. The communication of the proposed monitoring system is reliable, flexible and expandable, and easy to realize remote operation control. Moreover, the detection and control functions can be extended further. Through experiments, the effective control and monitoring of the designed monitoring system is verified, and the intelligent management is realized.

Multi-Time Scale Energy Storage Optimization of DC Microgrid Source-Load Storage Based on Virtual Bus Voltage Control

The energy storage adjustment strategy of source and load storage in a DC microgrid is very important to the economic benefits of a power grid. Therefore, a multi-timescale energy storage optimization method for direct current (DC) microgrid source-load storage based on a virtual bus voltage control is studied. It uses a virtual damping compensation strategy to control the stability of virtual bus voltage and establishes a virtual energy storage model by combining different types of distributed capability units. The design of an optimization process for upper-level daily energy storage has the objective function of maximizing the economic benefits of microgrids to cope with unplanned fluctuations in power. A real-time energy-adjustment scheme for the lower level is introduced, and a real-time energy-adjustment scheme based on virtual energy storage for the short-term partition of the source-load storage is designed to improve the reliability of microgrid operations. The experiment shows that, in response to the constant amplitude oscillation of the power grid after a sudden increase in power, this method introduces a virtual damping compensation strategy at 20 s, which can stabilize the virtual bus voltage. From 00:00 to 09:00, the battery power remains at around 4 MW, and from 12:00 to 21:00, the battery exits the discharge state. The economic benefits from applying this method are significantly higher than before. This method can effectively adjust the source-load energy storage in real time. During peak electricity price periods, the SOC value of supercapacitors is below 0.4, and during normal electricity price periods, the SOC value of supercapacitors can reach up to 1.0, which can make the state of the charge value of supercapacitors meet economic requirements.

Optimal Planning of Standalone Rural Microgrid With Effective Dispatch Strategies and Battery Technology

ABSTRACTMicrogrids are a viable substitute for traditional power systems because they may deliver cleaner, more dependable, affordable power with fewer losses. However, the microgrid's performance is impacted by the variable nature of renewable energy sources. Battery storage is a crucial component of microgrid planning since it defines the system's techno‐economic feasibility. A standalone rural microgrid is designed in the current study, employing three distinct battery types: lithium‐ion, lead acid, and zinc‐bromine flow. The suggested microgrid's techno‐economic analysis employs three distinct dispatch mechanisms, that is, cycle charging, load flow, and complete dispatch. The case study of the suggested framework is carried out in Lucknow (India). The system comprises PV/battery/wind energy system/diesel and battery. The simulation results suggest that the optimal system with the least electrification cost is 0.113 $/kWh using complete dispatch strategies and a zinc‐bromine battery. It has 206 kWh zinc‐bromine flow batteries, a 10 kW converter, a 20 kW PV, a 13‐kW diesel generator, and a Combined dispatch strategy. The system's net present cost per unit cost of energy is $40 275 and 0.113 $/kWh for the chosen region, respectively. Compared to the other two battery technologies for hybrid systems, the zinc‐bromine flow battery technology is also shown to be the most environmentally friendly. Among the three battery technologies available, zinc‐bromine flow is best used in a particular location's hybridized operation.

Optimization of emission scheduling in microgrids with electric vehicle integration

In the context of the continuous development of new energy vehicles, an increasing number of electric vehicles (EVs) are being integrated into microgrids, which impacts the operation of microgrids. It is necessary to analyze the emission scheduling of microgrids connected with EVs to ensure the smooth and reliable operation of microgrids with EV integration. This paper aims to realize optimal microgrid scheduling. This article took the case of EV connection with microgrids through orderly charging and discharging. Firstly, mathematical models for each output unit in the microgrid were established. Then, aiming to minimize both the operational cost and pollution emission treatment cost of the microgrid, an emission dispatch optimization model was developed. The whale optimization algorithm (WOA) was chosen as the solving algorithm, and an improved WOA (IWOA) was obtained by optimizing the original WOA in terms of population initialization and position updating parameters. An example analysis revealed that the IWOA demonstrated superior optimization performance compared to other optimization algorithms. In the scenario of orderly charging and discharging, the EVs discharged during peak hours and charged during off-peak hours to balance the microgrid load. The operating cost obtained through the IWOA was 967.25 yuan, and the pollution emission treatment cost was 241.52 yuan, resulting in a total cost of 1208.77 yuan. These results confirm the reliability of the proposed IWOA in solving the model and its applicability in optimizing microgrids with EV integration.

Fault in Converter Interfaced Micro Grid Using Detection and Identification of Hybrid Technique

ABSTRACTThis paper introduces a novel hybrid approach, termed ZOA‐SNN, for fault detection and identification in converter‐interfaced microgrids. By integrating the Zebra Optimization Algorithm (ZOA) with Spiking Neural Network (SNN) technology, the proposed method provides a comprehensive solution suitable for both grid‐connected and autonomous microgrid operation scenarios. The technique effectively isolates faults in the microgrid while maintaining operation continuity, particularly in islanded conditions. When operating in grid‐connected mode, distributed generators (DGs) provide electricity as needed. When the grid is not available, power sharing amongst DGs is controlled by voltage angle droop control. By isolating malfunctioning portions, the proposed protection system reduces load shedding, while DG control guarantees smooth islanding and resynchronization. Evaluation on the MATLAB platform demonstrates the superior performance of the proposed technique compared to existing algorithms such as Augmented Lagrangian Particle Swarm Optimization (ALPSO), Graph Convolutional Network (GCN), and Buffalo Optimization (BO). With an accuracy, recall, precision, and F1‐score reaching 98.5%, 99.2%, 99.1%, and 99.1%, respectively, the ZOA‐SNN approach excels in fault detection and classification. Additionally, it significantly reduces computation times for parameter calculation, enhancing efficiency in microgrid control systems. These results highlight the innovation and advantages of the ZOA‐SNN approach in enhancing the reliability and efficiency of fault detection systems in microgrid environments.

Multi‐timescale optimal scheduling of microgrids for generating new energy output scenarios based on correction error sampling intervals

AbstractMicrogrid can realize energy saving and emission reduction and multi‐energy complementation, but the fluctuation of renewable energy output and the error of day‐ahead scheduling will threaten the stability of microgrid operation. For this reason, this article proposes a microgrid multi‐timescale optimal scheduling method based on new energy output scenario generation. First, the microgrid framework of this article is introduced, and an energy cycle emission reduction model taking into account electricity‐to‐gas conversion is designed; second, a new energy prediction error model is established based on the prediction box and Gaussian hybrid model, and the scenario of wind and photovoltaic power generation is generated by correcting the sampling intervals for error sampling; and then, based on the day‐ahead scheduling plan, an intraday cooling, heating and electricity two‐layer rolling optimization model is established to correct the day‐ahead scenario. Finally, the example analysis shows that the cyclic emission reduction model can realize the recycling of resources, reduce the fuel cost and carbon emission, and the generation of scenarios for wind power can smooth out the fluctuation of new energy power, which, together with the intra‐day two‐layer rolling optimization, can reduce the day‐ahead scheduling error and improve the stability of microgrid operation.

Optimal planning and operation of heterogeneous autonomous and grid-connected microgrids based on multi-criteria techno-economic, environmental, and social indices

Sustainable energy transition involves the execution of recent technologies as a means of ensuring energy access and security. However, the increasing adoption of such technologies, particularly in the presence of diverse constraints, poses significant challenges from a planning perspective. In this context, the multi-objective analysis offers valuable insights for decision-making that balances mutual benefits, as relying solely on a single objective may increase the risk level for stakeholders engaged in coordinated decisions. Based on the real dataset, this study presents a comparative multi-criteria techno-economic, environmental, and social evaluation of site-specific unified standalone and grid-connected hybrid microgrids. The study employs a modified Last Cluster Mean Carried Forward approach for data processing, incorporating the Proprietary Derivative-free Algorithm and Original Grid-Search Algorithm to ensure a standardized comparison. Results reveal the substantial advantages of grid-connected systems over standalone counterparts, with reductions of 12.54 % to 63.73 % and 68.93 % to 89.13 % in terms of Net Present Cost and Levelized Cost of Energy, respectively. Grid-connected systems exhibit superior adaptability, recovering 52.3 % to 98.1 % surplus energy with a Renewable Fraction averaging 77.1 % to 87.9 %. However, these systems were hindered by frequent interruptions and required a minimum capacity shortage of 2.5 % to 3.5 %. Furthermore, grid-connected systems have proved feasible when carbon emissions, forests required to absorb the emissions, and the Social Cost of Carbon Emissions are considered in the range of 4.65–67.13 kiloton (metric), 423.32–6108.53 ha, and $0.24-$3.42 million, respectively. Social analysis and sensitivity analyses are performed to justify the robustness and adaptability. Lastly, the findings are followed by policy recommendations and results validation by comparing prevailing government tariffs and other studies.

Hierarchical Optimal Dispatching of Electric Vehicles Based on Photovoltaic-Storage Charging Stations

Electric vehicles, known for their eco-friendliness and rechargeable–dischargeable capabilities, can serve as energy storage batteries to support the operation of the microgrid in certain scenarios. Therefore, photovoltaic-storage electric vehicle charging stations have emerged as an important solution to address the challenges posed by energy interconnection networks. However, electric vehicle charging loads exhibit notable randomness, potentially altering load characteristics during certain periods and posing challenges to the stable operation of microgrids. To address this challenge, this paper proposes a hierarchical optimal dispatching strategy based on photovoltaic-storage charging stations. The strategy utilizes a dynamic electricity pricing model and the adaptive particle swarm optimization algorithm to effectively manage electric vehicle charging loads. By decomposing the dispatching task into multiple layers, the strategy effectively solves the problems of the “curse of dimensionality” and slow convergence associated with large numbers of electric vehicles. Simulation results demonstrate that the strategy can effectively achieve peak shaving and valley filling, reducing the load variance of the microgrid by 24.93%, and significantly reduce electric vehicle charging costs and distribution network losses, with a reduction of 92.29% in electric vehicle charging costs and 32.28% in microgrid losses compared to unorganized charging. Additionally, this strategy can meet the travel demands of electric vehicle owners while providing convenient charging services.

Application of an Optimal Fractional-Order Controller for a Standalone (Wind/Photovoltaic) Microgrid Utilizing Hybrid Storage (Battery/Ultracapacitor) System

Nowadays, standalone microgrids that make use of renewable energy sources have gained great interest. They provide a viable solution for rural electrification and decrease the burden on the utility grid. However, because standalone microgrids are nonlinear and time-varying, controlling and managing their energy can be difficult. A fractional-order proportional integral (FOPI) controller was proposed in this study to enhance a standalone microgrid’s energy management and performance. An ultra-capacitor (UC) and a battery, called a hybrid energy storage scheme, were employed as the microgrid’s energy storage system. The microgrid was primarily powered by solar and wind power. To achieve optimal performance, the FOPI’s parameters were ideally generated using the gorilla troop optimization (GTO) technique. The FOPI controller’s performance was contrasted with a conventional PI controller in terms of variations in load power, wind speed, and solar insolation. The microgrid was modeled and simulated using MATLAB/Simulink software R2023a 23.1. The results indicate that, in comparison to the traditional PI controller, the proposed FOPI controller significantly improved the microgrid’s transient performance. The load voltage and frequency were maintained constant against the least amount of disturbance despite variations in wind speed, photovoltaic intensity, and load power. In contrast, the storage battery precisely stores and releases energy to counteract variations in wind and photovoltaic power. The outcomes validate that in the presence of the UC, the microgrid performance is improved. However, the improvement is very close to that gained when using the proposed controller without UC. Hence, the proposed controller can reduce the cost, weight, and space of the system. Moreover, a Hardware-in-the-Loop (HIL) emulator was implemented using a C2000™ microcontroller LaunchPad™ TMS320F28379D kit (Texas Instruments, Dallas, TX, USA) to evaluate the proposed system and validate the simulation results.

A cooperative approach for generation and lines expansion planning in microgrid‐based active distribution networks

AbstractWith the growth of the load in the electricity networks, sufficient investment in the generation and lines expansion should be made in order to provide the energy needed by consumers with the lowest possible investment and operation costs. This issue is especially important in distribution networks, which are faced with the uncertainties of renewable energy generation and the development of microgrids and related issues.In this article, the planning of generation and lines expansion has been modeled with the aim of minimizing the total costs of microgrids, based on the cooperative approach. For this purpose, a bi‐level model has been developed; on the upper level, microgrids make investment decisions with a cooperative approach, and a constrained stochastic formulation has been developed with considering operational uncertainties on the lower level. Also, in this article, in order to ensure the supply of critical loads in island conditions, the self‐sufficiency index is defined. Three case studies have been considered to ensure the effectiveness of the developed model. In case 1, each microgrid will be able to supply its load only by generating of its units and purchasing from the retail market. In case 2, the possibility of trading with other microgrids in a non‐cooperative approach will also be available to the microgrids operators, and in case 3, microgrids can exchange energy with other microgrids in a cooperative manner. The simulation results showed that due to the possibility of using nearby microgrid resources, the cost of microgrid load supply in case 2 was reduced by 4.84% compared to case 1. Also, this cost in case 3 was reduced by 5.23% and 0.38%, respectively, compared to cases 1 and 2, due to the use of a cooperative manner in microgrid load providing.

A two-layer strategy for sustainable energy management of microgrid clusters with embedded energy storage system and demand-side flexibility provision

The intermittent nature of renewable energy generation and the fluctuating demands pose persistent challenges in microgrid operations. In response, stakeholders and operators have turned to clustering the geographically adjacent microgrids as a solution. In this context, this paper introduces a novel two-layer energy management strategy for microgrid clusters, utilizing demand-side flexibility and the capabilities of shared battery energy storage (SBES) to minimize operational costs and emissions, while ensuring a spinning reserve within individual microgrids to prevent load-shedding. In the lower layer, the proposed approach devises optimal day-ahead operation policies, while the upper layer employs a cooperative strategy to further optimize the operational efficiency across the entire cluster. The energy management problem is accurately formulated as a mixed integer quadratic programming (MIQP) optimization, which incorporates linear terms in the problem's constraints. The formulation accounts for operational costs associated with SBES including expenses of charging/discharging and changes in operating states (CiOS). Real-world case studies with a cluster of three microgrids in Australia validate the effectiveness of this approach. Results show a reduction in operational costs for the base case scenario by 6.96 % compared to conventional microgrid management strategies. Sensitivity analyses further demonstrate the economic benefits of varying SBES capacity and flexibility pricing, with savings ranging from 6.5 % to 8.1 %. The proposed strategy also reduces CO2 emissions by up to 11.6 %, while improving system reliability. This strategy holds promise for integration into distributed energy systems with high renewable penetration and clustered local grids, offering significant advantages for utility operators and end-users through improved energy efficiency and reduced emissions.

Voltage Deviation Improvement in Microgrid Operation through Demand Response Using Imperialist Competitive and Genetic Algorithms

In recent decades, with the expansion of distributed energy generation technologies and the increasing need for more flexibility and efficiency in energy distribution systems, microgrids have been considered a promising innovative solution for local energy supply and enhancing resilience against network fluctuations. One of the basic challenges in the operation of microgrids is the optimal management of voltage and frequency in the network, which has been the subject of extensive research in the field of microgrid operational optimization. The energy demand is considered a crucial element for energy management due to its fluctuating nature over the day. The use of demand response strategies for energy management is one of the most important factors in dealing with renewables. These strategies enable better energy management in microgrids, thereby improving system efficiency and stability. Given the complexity of optimization problems related to microgrid management, evolutionary optimization algorithms such as the Imperialist Competitive Algorithm (ICA) and Genetic Algorithm (GA) have gained great attention. These algorithms enable solving high-complexity optimization problems by considering various constraints and multiple objectives. In this paper, both ICA and GA, as well as their hybrid application, are used to significantly enhance the voltage regulation in microgrids. The integration of optimization techniques with demand response strategies improves the overall system efficiency and stability. The results proved that the hybrid method provides valuable insights for optimizing energy management systems.

A Real-Time and Online Dynamic Reconfiguration against Cyber-Attacks to Enhance Security and Cost-Efficiency in Smart Power Microgrids Using Deep Learning

Ensuring the secure and cost-effective operation of smart power microgrids has become a significant concern for managers and operators due to the escalating damage caused by natural phenomena and cyber-attacks. This paper presents a novel framework focused on the dynamic reconfiguration of multi-microgrids to enhance system’s security index, including stability, reliability, and operation costs. The framework incorporates distributed generation (DG) to address cyber-attacks that can lead to line outages or generation failures within the network. Additionally, this work considers the uncertainties and accessibility factors of power networks through a modified point prediction method, which was previously overlooked. To achieve the secure and cost-effective operation of smart power multi-microgrids, an optimization framework is developed as a multi-objective problem, where the states of switches and DG serve as independent parameters, while the dependent parameters consist of the operation cost and techno-security indexes. The multi-objective problem employs deep learning (DL) techniques, specifically based on long short-term memory (LSTM) and prediction intervals, to effectively detect false data injection attacks (FDIAs) on advanced metering infrastructures (AMIs). By incorporating a modified point prediction method, LSTM-based deep learning, and consideration of technical indexes and FDIA cyber-attacks, this framework aims to advance the security and reliability of smart power multi-microgrids. The effectiveness of this method was validated on a network of 118 buses. The results of the proposed approach demonstrate remarkable improvements over PSO, MOGA, ICA, and HHO algorithms in both technical and economic indicators.

Advanced energy management scheme for fuel cell-based microgrid using self–regulated controller and switched capacitor inverter

Clean energy production is now the main challenge for sustainable future which can be addressed by introducing renewable energy sources. Fuel cells are critical in providing sustainable energy solutions by enabling efficient energy conversion in microgrids. To enhance the performance of fuel cell-based microgrids, advanced controllers and inverters are necessary to manage power quality and stability. One of the key benefits of this fuel cell is the separation of energy conversion and management, which allows independent optimization for each function of microgrid's performance, cost, or other installation considerations. The ability to individually control of each component of a microgrid can significantly impact various applications positively. Beyond their technological and economic advantages, fuel cells are highly sensitivity to microgrid's characteristics such as current quality and harmonics which creates difficulties for their design and management. Therefore, the entire microgrid must be managed by an effective energy management strategy and integration of advanced inverter topologies. This study aims to improve fuel cell efficiency and power quality within the microgrid through an advanced energy management (AEM) strategy. The proposed AEM structure is developed focusing on two key components: a self-regulated controller (SRC) and a switched capacitor multilevel inverter (SCMLI). These elements work together to mitigate the disturbances and enhance the power quality of the system. The methodology includes simulation and hardware-in-the-loop (HIL) testing under non-linear load conditions. Initial grid-side current total harmonic distortion (THD) of 28.38% was reduced to 2.19% through the proposed system. An impact analysis is also presented to demonstrates that reducing current harmonics and voltage imbalance have improved the efficiency of fuel cell to 50.18% and fuel utilization to 98.05%. The findings show that the proposed scheme significantly reduces current harmonics and improves the overall performance benchmark of the microgrid and fuel cell.

Advancing microgrid operation: leveraging a load dispatch based-ANN for a multi-source energy integration scenario

Advancing microgrid operation: leveraging a load dispatch based-ANN for a multi-source energy integration scenario

Practical solutions for microgrid energy management: Integrating solar forecasting and correction algorithms

Nowadays, the shift towards renewable energies is happening at an exponential pace. Microgrids are an integral part in integrating renewable energies into the global energy mix. Due to the volatility of renewables, such as solar or wind, proper energy management is needed to avoid generation or load curtailment. This issue is addressed throughout the literature using a wide variety of strategies, ranging from classical linear to nature inspired metaheuristic optimization algorithms. This paper goes beyond the simulation phase of different optimization algorithms and addresses the optimal energy management problem by proposing a novel framework to integrate optimization strategies into the daily operation of microgrids. The proposed framework showcases 3 practical methods for controlling the distributed generators, as well as a communication scheme which facilitates the data transfer between the machine running the optimization strategy and the energy management system of the microgrid. The framework is demonstrated on a small-scale islanded microgrid setup, located at the Technical University of Cluj-Napoca. The microgrid setup consists of a photovoltaic array, a battery energy storage system and two dispatchable generators. A two-stage optimization strategy is used, consisting of a day-ahead stage, which uses the solar forecast provided by the Global Forecast System, prior to each day, to issue a working plan for the dispatchable generators, and an intra-day stage, which uses hourly solar forecasts, issued during the day, to adjust the operation of the microgrid and minimize the error between the day-ahead solar forecast and the actual weather conditions. Mixed integer linear programming is used to solve the optimization problem and validate the correct operation of the proposed framework over two case studies. The results show that the microgrid works as intended, in both scenarios, as well as the benefits of using an intra-day correction stage.

Evaluating Microgrid Investments: Introducing the MPIR Index for Economic and Environmental Synergy

In view of the increasing environmental challenges and the growing demand for sustainable energy solutions, the optimization of microgrid systems with regard to economic efficiency and environmental compatibility is becoming ever more important. This paper presents the Microgrid Performance and Investment Rating (MPIR) index, a novel assessment framework developed to link economic and environmental objectives within microgrid configurations. The MPIR index evaluates microgrid configurations based on five critical dimensions: financial viability, sustainability, regional renewable integration readiness, energy demand, and community engagement, facilitating comprehensive and balanced decision making. The current cases focus on the area of Greece; however, the model can have a wider application. Developed using a two-target optimization model, this index integrates various energy sources—including photovoltaics, micro-wind turbines, and different types of batteries—with advanced energy management strategies to assess and improve microgrid performance. This paper presents case studies in which the MPIR index is applied to different microgrid scenarios. It demonstrates its effectiveness in identifying optimal configurations that reduce the carbon footprint while maximizing economic returns. The MPIR index provides a quantifiable, scalable tool for stakeholders, not only advancing the field of microgrid optimization, but also aligning with global sustainability goals and promoting the transition to a more resilient and sustainable energy future.

Experimental investigation of adaptive multi-generalized integrator-based controller for electronically interfaced hybrid microgrid system

This research work explores the conceptualization and evaluation of a hybrid microgrid that taps into the potential of solar photovoltaic systems, wind energy conversion systems, and battery energy storage systems. In practice, nonlinear loads pose power quality issues that significantly impact the performance of hybrid microgrids. To tackle these challenges, an adaptive multi-generalized integrator (MGI) filter is proposed. This filter extracts the fundamental signal from the distorted utility grid voltages. It features a pre-filter with a DC-off set rejection loop, effectively minimizing the DC-offsets from the distorted grid voltages. This facilitates the distribution of active power generated by the hybrid microgrid's sources while simultaneously addressing various power quality problems. In addition, a dynamic power management control approach enhances grid resilience by operating the hybrid microgrid in grid-connected and islanding modes. It provides uninterrupted and high-quality power supply to consumers during grid outages. The performance of this filter is comprehensively assessed through numerical simulations in MATLAB®/Simulink® environment. A real-time laboratory prototype is developed with WAVECT® WUC300 FPGA controller, demonstrating the practical application of the proposed filter. It ensures the minimum DC-offsets of 0.02V, fast convergence, and minimum oscillations. The grid synchronization and power quality index of the grid currents simultaneously achieve a THD of 2.82 %, complying with the IEEE-1547 and IEEE-519 standards. Importantly, the proposed adaptive-MGI filter outperforms the conventional SOGI and LMF filters in terms of nonlinear load tracking capabilities, with a response speed of less than 200μs, thereby highlighting its practical relevance and importance.

Digital twin-enhanced opportunistic maintenance of smart microgrids based on the risk importance measure

Smart microgrids face more diverse and frequent risks than traditional grids due to their complexity and reliance on distributed generation. Ensuring the reliable operation of smart microgrids requires effective maintenance. Traditional maintenance methods, based on periodic inspections and fault diagnosis, struggle to adapt to the dynamics and complexity of microgrid systems. The introduction of digital twin technology provides a new solution for the opportunistic maintenance of microgrid systems. This paper presents a digital twin microgrid architecture for real-time monitoring and decision-making in opportunistic maintenance. Meanwhile, this paper introduces a risk importance measure to aid to optimize opportunistic maintenance strategies when resources are limited. Finally, a wind-solar-storage microgrid is used to illustrate the proposed method. Experimental results show that the proposed method significantly reduces maintenance costs and improves system reliability, effectively supporting microgrid maintenance.

A multi-agent system approach for real-time energy management and control in hybrid low-voltage microgrids

The real-time operation of microgrids is crucial due to its ability to enhance energy resilience and efficiency. Continuous monitoring and adaptation to fluctuations in energy supply and demand ensure a stable and reliable electricity supply to local communities, even in the case of grid disturbances. This article presents an efficient and easily implementable real-time energy management and control system based on multi-agent systems for hybrid Low-Voltage Micro-Grids (LVMGs) using energy storage systems and renewable sources. The main objective of the proposed approach is to determine optimal setpoints for all microgrid components to improve overall efficiency and reduce electricity costs while satisfying multiple constraints. The well-defined flexibilities of all microgrid components to adjust their power are exploited to achieve optimal power allocation. The approach is tested and validated by developing a simulation environment using the Java Agent Development (JADE) framework, enabling the implementation of microgrid optimization through MATLAB/Simulink.