Operando X-ray Absorption Research Articles

Enhanced stability of boron modified NiFe hydroxide for oxygen evolution reaction.

The introduction of non-metal elements including boron has been identified as a significant means to enhance oxygen evolution reaction (OER) performance in NiFe-based catalysts. To understand the catalytic activity and stability, recent attention has widened toward the Fe species as a potential contributor, prompting exploration from various perspectives. Here, boron incorporation in NiFe hydroxide achieves significantly enhanced activity and stability compared to the boron-free NiFe hydroxide. The boron inclusion in NiFe hydroxide is found to show exceptionally improved stability from 12 to 100 hours at a high current density (200 mA cm-2). It facilitates the production and redeposition of OER-active, high-valent Fe species in NiFe hydroxide based on the operando Raman, UV-vis, and X-ray absorption spectroscopy analysis. It is proposed that preserving a homogenous distribution of Fe across the boron-containing catalyst surface enhances OER stability, unlike the bare NiFe hydroxide electrocatalyst, which exhibits uneven Fe dissolution, confirmed through elementary mapping analysis. These findings shed light on the potential of anionic regulation to augment the activity of iron, an aspect not previously explored in depth, and thus are expected to aid in designing practical OER electrocatalysts.

Designing bifunctional perovskite catalysts for the oxygen reduction and evolution reactions.

The development of unified regenerative fuel cells (URFCs) necessitates an active and stable bifunctional oxygen electrocatalyst. The unique challenge of possessing high activity for both the oxygen reduction (ORR) and oxygen evolution (OER) reactions, while maintaining stability over a wide potential window impedes the design of bifunctional oxygen electrocatalysts. Herein, two design strategies are explored to optimize their performance. The first incorporates active sites for the ORR and OER, Mn and Co, into a single perovskite structure, which is achieved with the perovskites Ba0.5Sr0.5Co0.8Mn0.2O3-δ (BSCM) and La0.5Ba0.25Sr0.25Co0.5Mn0.5O3-δ (LBSCM). The second combines an active ORR perovskite catalyst (La0.4Sr0.6MnO3-δ (LSM)) with an OER active perovskite catalyst (Ba0.5Sr0.5Co0.8Fe0.2O3-δ (BSCF)) in a physical mixed composite (BSCF/LSM). The success of the two strategies is investigated by measuring the catalysts' catalytic performance and response to alternating reducing and oxidizing potentials to mimic the dynamic conditions experienced during the operation of URFCs. Additionally, the continuous, potentiodynamic change in Mn, Co, and Fe oxidation states during the ORR and OER is elucidated with operando X-ray absorption spectroscopy (XAS) measurements, revealing key insights into the nature of the active sites. The results reveal important catalyst physiochemical properties and provide a guide for future research and design principles for bifunctional oxygen electrocatalysts.

Operando insights into correlating CO coverage and Cu-Au alloying with the selectivity of Au NP-decorated Cu2O nanocubes during the electrocatalytic CO2 reduction.

Electrochemical reduction of CO2 (CO2RR) is an attractive technology to reintegrate the anthropogenic CO2 back into the carbon cycle driven by a suitable catalyst. This study employs highly efficient multi-carbon (C2+) producing Cu2O nanocubes (NCs) decorated with CO-selective Au nanoparticles (NPs) to investigate the correlation between a high CO surface concentration microenvironment and the catalytic performance. Structure, morphology and near-surface composition are studied via operando X-ray absorption spectroscopy and surface-enhanced Raman spectroscopy, operando high-energy X-ray diffraction as well as quasi in situ X-ray photoelectron spectroscopy. These operando studies show the continuous evolution of the local structure and chemical environment of our catalysts during reaction conditions. Along with its alloy formation, a CO-rich microenvironment as well as weakened average CO binding on the catalyst surface during CO2RR is detected. Linking these findings to the catalytic function, a complex compositional interplay between Au and Cu is revealed in which higher Au loadings primarily facilitate CO formation. Nonetheless, the strongest improvement in C2+ formation appears for the lowest Au loadings, suggesting a beneficial role of the Au-Cu atomic interaction for the catalytic function in CO2RR. This study highlights the importance of site engineering and operando investigations to unveil the electrocatalyst's adaptations to the reaction conditions, which is a prerequisite to understand its catalytic behavior.

Design principles of operando ultraviolet-visible and electron paramagnetic resonance spectroscopy setups for active site characterization in ion-exchanged zeolites

Cu- and Fe-exchanged zeolites have been widely investigated for their applicability in selective partial oxidation of CH4 and abatement of environmentally harmful nitrogen oxides. However, the differentiation between spectator and active sites is cumbersome due to their dynamic co-existence, which aggravates the elucidation of the redox dynamics of the latter. Therefore, correlated multi-spectroscopic approaches carried out under operando conditions are needed in order to disentangle the inherent reactivity of specific species. Here we describe the conceptualization of complementary operando spectroscopic methods for the investigation of ion-exchanged zeolites employed in redox reactions. The potential and versatility of this approach are demonstrated by means of two exemplary case studies. First, we present the insight generated by two custom operando ultraviolet-visible and electron paramagnetic resonance spectroscopy setups operating in batch mode into CH4-to-CH3OH conversion over Cu-exchanged mordenite. In addition to recording the method-dependent spectroscopic fingerprints of distinct Cu centers, the overall CH4 consumption is simultaneously monitored in both setups. The extracted apparent activation energies of the reactive centers obtained from the two systems are in good agreement with each other allowing to link the bulk reactivity to the intrinsic site-specific kinetics of all Cu centers. Second, the EPR setup is equipped with a flow reactor designed to carry out modulated excitation experiments with phase-sensitive detection in order to improve the signal-to-noise ratio and time resolution. The cell is employed to study the conversion of NO via selective catalytic reduction over Fe-exchanged ferrierite. In combination with operando X-ray absorption spectroscopy, a small portion of active Fe species consisting of monomers in gamma-positions and oligomeric structures located in the main channel is identified, which are kept in a redox active state under relevant reaction conditions and thus sustain the chemical transformation of NO.

Vacancy Defects Inductive Effect of Asymmetrically Coordinated Single-Atom Fe─N3 S1 Active Sites for Robust Electrocatalytic Oxygen Reduction with High Turnover Frequency and Mass Activity.

The development of facile, efficient synthesis method to construct low-cost and high-performance single-atom catalysts (SACs) for oxygen reduction reaction (ORR) is extremely important, yet still challenging. Herein, an atomically dispersed N, S co-doped carbon with abundant vacancy defects (NSC-vd) anchored Fe single atoms (SAs) is reported and a vacancy defects inductive effect is proposed for promoting electrocatalytic ORR. The optimized catalyst featured of stable Fe─N3 S1 active sites exhibits excellent ORR activity with high turnover frequency and mass activity. In situ Raman, attenuated total reflectance surface enhanced infrared absorption spectroscopy reveal the Fe─N3 S1 active sites exhibit different kinetic mechanisms in acidic and alkaline solutions. Operando X-ray absorption spectrareveal the ORR activity of Fe SAs/NSC-vd catalyst in different electrolyte is closely related to the coordination structure. Theoretical calculation reveals the upshifted d band center of Fe─N3 S1 active sites facilitates the adsorption of O2 and accelerates the kinetics process of *OH reduction. The abundant vacancy defects around the Fe─N3 S1 active sites balance the OOH* formation and *OH reduction, thus synergetically promoting the electrocatalytic ORR process.

Operando x-Ray Absorption Spectroscopy Investigation of Secondary Metal Doping into Iron-Nitrogen-Carbon Catalysts for Oxygen Electroreduction

Oxygen reduction reaction (ORR) plays a key role in the development of fuel cell technology, and great efforts have been made to reduce the amount of platinum, required to speed up this sluggish reaction, or, even more desirable, to use efficient electrocatalysts based on earth-abundant metals. To date, numerous single-atom catalysts in the form of metal-doped carbon-nitrogen materials (MNC) have proved to be a promising alternative to ORR Pt-based materials. [1-3]In this study we employed advanced spectroscopic techniques, namely Mössbauer spectroscopy and operando X-ray absorption (XAS) spectroscopy, to understand the structural and electronic factors underlying an increase in the catalytic turn over frequency (TOF) of bimetallic FeSnNC and FeCoNC catalysts, relative to the parent FeNC materials. In particular, 57Fe Mössbauer spectroscopy identified a larger ratio of D1/D2 species in both bimetallic catalysts, supporting a larger ratio of Fe(III)-Nx/Fe(II)-Nx sites. The combination of extended X-ray absorption fine structure (EXAFS) modeling, and the analysis of operando X-ray absorption near-edge spectroscopy (XANES) spectra revealed a disordered carbon structure around FeNx active sites, and variations in the iron oxidation state that can be linked to the enhanced intrinsic catalytic reactivity (TOF). This talk is therefore intended to draw attention to the potential of the XAS technique, especially when applied to in-situ/operando studies in the field of electrocatalysis. References F. Luo, A. Roy, L. Silvioli, D.A. Cullen, A. Zitolo, M.T. Sougrati, I.C. Oguz, T. Mineva, D. Teschner, S. Wagner, J. Wen, F. Dionigi, U.I. Kramm, J. Rossmeisl, F. Jaouen and P. Strasser. P-block single-metal-site tin/nitrogen-doped carbon fuel cell cathode catalyst for oxygen reduction reaction. Nature Materials 2020, 19, 1215-1223A. Zitolo, N. Ranjbar, T. Mineva, J. Li, Q. Jia, S. Stamatin, G.F. Harrington, S.M. Lyth, P. Krtil, S. Mukerjee, E. Fonda, F. Jaouen. Identification of catalytic sites in cobalt-nitrogen-carbon materials for the oxygen reduction reaction. Nature Communications 2017, 8(1), 957A. Zitolo, V. Goellner, V. Armel, M. T. Sougrati, T. Mineva, L. Stievano, E. Fonda, F. Jaouen. Identification of catalytic sites for oxygen reduction in iron and nitrogen doped graphene materials. Nature Materials 2015, 14, 937-942

Tracking Mn and Zn in Rechargeable Aqueous Zn-MnO2 Batteries By Operando X-Ray Absorption

Zn-MnO2 batteries with mildly acidic electrolytes are a promising chemistry for large scale storage thanks to their remarkable energy density, low cost, and high safety. This is mainly obtained thanks to the high capacity of the Zn metal anode, and the nonflammable character of the aqueous electrolyte. MnO2 is one of the most common cathode of choice, not only for being Earth-abundant, but also because it can undergo a two-electron mechanism, which is however complex and still not fully understood. There is currently agreement in considering for discharge a MnO2 dissolution, leading to soluble Mn2+ and simultaneous precipitation of Zinc Hydroxide Sulfate (ZHS, ZnSO4[Zn(OH2)]3·xH2O). When charging the process is not simply reverted. In fact, a distinct electrochemical profile is observed, with at least two distinct plateaus and a third, apparently pseudocapacitive stage (Figure 1a). A similar multistage profile is observed during the second discharge. Although such profile is characteristic and observed with different MnO2 phases and architectures, the underlying mechanism remains elusive, as it seems to involve mainly poorly crystallized phases.We studied the mechanism by operando X-ray absorption (XAS) at the Mn and Zn K-edges to follow speciation simultaneously and quantitatively in the cathode and in the electrolyte via principal component analysis. Beam intensity needed appropriate regulation to avoid interference with the experiment.Simultaneous X-ray diffraction allowed precise correlation with the MnO2 dissolution and ZHS formation. We found evidence of Mn(III) intermediate occurring during local bond reorganization, which is inferred by the significant evolution of the absorption fine structure region (EXAFS) of the Mn K-edge (Figure 1b). In contrast, minor Zn spectral changes reflect primarily processes of precipitation and dissolution, suggesting that no Zn-Mn mixed phases form during cycling. Figure 1

Metastable Ni(I)-TiO2-X Photocatalyst: Self-Amplifying H2 Evolution from Plain Water without Noble Metal Co-Catalyst and Sacrificial Agent

This contribution describes the self-assembling and self-activating nature of a TiO2 photocatalyst that generates hydrogen from water in the absence of sacrificial species or noble metal co-catalysts [1]. Such system forms when nanoparticles of reduced anatase TiO2 are illuminated in an aqueous Ni2+ solution [2,3]. UV illumination creates in-situ a Ni+/TiO2/Ti3+ photocatalyst that over time produces H2 at a higher rate. Thus, UV light is both the synthesis tool that forms this active metastable photocatalytic entity and the energy provider for this entity to enable H2 evolution from water.Operando X-ray absorption (XAS) and electron paramagnetic (EPR) spectroscopies show that key to self-assembly and self-activation is the light-induced formation of defects in the semiconductor [4], which enables the formation of monovalent Ni+ surface states. Metallic nickel states, i.e., Ni0, do not form, neither in the dark (resting state) nor under illumination (active state). Once the catalyst is assembled, the Ni+ surface states act as electron relay for electron transfer to form H2 from water.Self-amplifying reaction schemes of this type entail considerable potential for developing a new generation of photocatalysts via simple one-pot synthesis routes.

Operando X-Ray Absorption Spectroscopy of Solid Electrolyte Interphase Formation on Silicon Anodes

Lithium-ion batteries (LIBs) are key to the transition from fossil fuels towards increased use of renewable energy sources. However, more widespread deployment requires improvements in energy density, cost and cycle-lifetime. Various cathode and anode materials are under consideration for next-generation LIBs, and the interfacial stability of these materials in contact with the electrolyte is a critical consideration. Interface-sensitive operando characterization techniques are thus urgently needed to reveal the reactions occurring in working batteries.1,2 The solid electrolyte interphase (SEI) that forms on Li-ion battery anodes is critical to their long-term performance, however observing SEI formation processes at the buried electrode-electrolyte interface is a significant challenge. Here we show that operando soft X-ray absorption spectroscopy in total electron yield mode can resolve the chemical evolution of the SEI during electrochemical formation in a Li-ion cell, with nm-scale interface sensitivity. O, F, and Si K-edge spectra, acquired as a function of potential, reveal when key reactions occur on high-capacity amorphous Si anodes cycled with and without fluoroethylene carbonate (FEC).3 Cross-referencing to cycling data, complementary bulk sensitive fluoresecent yield (FY) XAS measurements, and density functional theory (DFT) calculated spectra enables identification of the electrolyte and SEI species, and the dominant mechanisms of SEI formation. Without FEC present, LiF formation is detected at 0.6 V vs. Li/Li+ prior to significant lithiation of the a-Si, whilst at lower potentials the SEI grows in thickness with an increased contribution from organic components containing -C(=O)O- species. The observed sequential formation of inorganic and organic components is implicated in layering of the SEI. With FEC as an additive we see the onset of SEI formation at much higher potentials (1.0 V vs. Li/Li+), and attribute the improved cycle life seen with this additive to the rapid healing of SEI defects formed during delithiation. Operando TEY-XAS offers new insights into the formation mechanisms of electrode-electrolyte interphases and their stability for a wide variety of electrode materials and electrolyte formulations. References Wu et al. Phys. Chem. Chem. Phys. 2015, 17, 30229.Weatherup et al. Top. Catal. 2018, 61, 2085.Swallow et al. Nature Commun. 2022, 13, 6070.

(Keynote) Competition of Oxygen and Chlorine Evolution on Oxide Surfaces – a Soft X-Ray and Dems Approach to Identification of Active Site

Anodic gas evolving reactions, e.g. oxygen evolution and chlorine evolution, are of fundamental importance both in energy storage as well as in electrolytic production of chemicals. Both reactions are of electrocatalytic nature, proceed in the same potential range and are catalyzed by the same types of electrode materials. While the oxygen evolution is thermodynamically favored the two electron chlorine evolution is kinetically preferred, namely at acid and neutral pH. This kinetic preference is industrially explored in chlor-alkali processes as well in chlorate electrolysis. The growing interest in electrolytic hydrogen production fueled by the popularity of the hydrogen as the likely replacement of fossil fuels brings up the question of the tolerance of the industrial anodes to presence of chlorides in the water intended for electrolytic hydrogen production. Such a tolerance can be best achieved by steering the selectivity of the anode between oxygen and chlorine evolution aiming eventually at the possibility of the sea water use in hydrogen producing water electrolysis. So far existing attempts at control the anode selectivity in presence of chlorides explore two principal approaches – pH control and surface engineering. While the pH related approach is rationalized by different pH sensitivity of each of the competing reaction the surface engineering related activities so far rely on trial and error approach. Qualitatively the selectivity may be controlled by either selectively promoting/suppressing each of the contributing reactions. While the literature lists attempts when the overall selectivity towards OER is apparently achieved by selective suppression of CER [1] more recent reports suggest that the actual selectivity is in fact controlled by the ability of the catalysts to support a lattice oxygen activating mechanism of the oxygen evolution process [2]. While these assignments are based on correlation of selectivity measurements with local structure and DFT modelling and a direct evidence of such a behavior is so far missing. This paper will document here the capability of the real-time and operando soft X-ray absorption spectroscopy [3] to provide this missing evidence. Anodic behavior of two type of ruthenium oxide electrodes in chloride free and chloride containing solutions will be documented by comparison of the nature and potential dependent population of the oxygen related intermediates formed at anode surface in the potential range of oxygen and chlorine evolution in acid media (pH=1) and combined with DEMS data to identify the active sites for each contributing electrode reaction.

Operando and Dynamic XAS Studies of Metal-Support Interactions of Iridium-Based Catalysts for Oxygen Evolution Reaction (OER) in Proton Exchange Membrane Water Electrolysis (PEMWE)

Iridium (Ir) is an important electrocatalyst material for the oxygen evolution reaction (OER) in acidic media. However, high loadings of very costly and scarce Ir are needed to achieve sufficient performance in proton exchange membrane water electrolysis (PEMWE). [1] To establish a large-scale green hydrogen economy based on PEMWE in the near future, the Ir loading needs to be further reduced. In the last decades, promising Ir-based catalyst strategies has been developed to improve the OER activity by controlling the size of Ir nanoparticles (NPs) [2] and tuning the electronic interactions of the Ir NPs with the catalyst support material, referred to as strong metal support interaction (SMSI). The latter has frequently been observed for heterogeneous catalysts (e.g. Au NPs supported on titanium oxide [3]), while the SMSI for Ir-based OER electrocatalysts is poorly understood to date.This study focuses on operando and dynamic X-ray absorption spectroscopy (XAS) analysis of Ir NPs deposited on three support materials: graphitized carbon (C), titanium oxide (TiO2) and antimony-doped tin oxide (ATO). The surfactant-free Ir NPs with controlled size of around 1 nm were obtained by a colloidal approach in low-boiling point alcohols. [2, 4] Afterwards, the Ir NPs were homogeneously distributed on different support materials with similar loadings and particle sizes confirmed by TEM and XRD. Solute components from the aged catalyst materials (Ir and/or support material) in the electrolyte solution were determined by ICP-OES, while the solid catalyst powders were analysed by TGA and µ-XRF. Our first/initial electrochemical results by recording cyclic voltammetry (CV) profiles show that after the immobilization the Ir NPs obtained from the same batch are strongly oxidized on TiO2, while a metallic character of the Ir is still observed on the C and ATO. The OER mass activity of 120±8 A/gIr for Ir/C is 2-times higher than for Ir/TiO2 (60±6 A/gIr) and 1.2-times higher than for Ir/ATO (95±4 A/gIr) at 1.5 VRHE,iR-free and 25 °C obtained from rotating disc electrode (RDE) setup.Operando and dynamic Ir LIII edge XANES measurements during the cycling from 0.06 to different upper potentials (0.8, 1.0, 1.2, 1.4 and 1.6 VRHE) at 2 mV/s were performed in acidic media at the SuperXAS (X10DA) beamline, Switzerland. All measurements were carried out using a home-made spectro-electrochemical flow-cell. Principal component analysis (PCA) of Quick-XANES data confirmed the tendencies of the formation of irreversible Irz+ species on TiO2 even at low upper potentials, while ATO and C tend to retain the metallic character of the Ir NPs. From the PCA, two independent components were identified to describe the changes in the series of XANES data. The compositions of these components were then analyzed using linear combination fitting (LCF).For 60 wt.% Ir/C, the cycling up to 1.4 VRHE shows two components with 50:25:25 wt.% of Ir0:Ir3+:Ir4+ and 42:0:58 wt.% of Ir0:Ir3+:Ir4+ obtained from the PCA and LCF analysis. During the cycling, the ratios of these components change gradually. In spite of the strong hysteresis behavior, we observed that the ratio between both components reverses to the initial state. In other words, only the component with 42:0:58 wt.% of Ir0:Ir3+:Ir4+ is present at 1.4 VRHE, while the other component is dominant at lower anodic potential.In the same experiment, the analysis of our data for 60 wt% Ir/ATO using PCA indicates two independent components with 74:11:15 wt.% of Ir0:Ir3+:Ir4+ and 70:0:30 wt.% of Ir0:Ir3+:Ir4+. The cycling up to 1.4 VRHE shows similar behavior like 60 wt.% Ir/C.Although the same batch of colloidal Ir NPs were used for the immobilization, the PCA and LCF analysis for 60 wt.% Ir/TiO2 reveal two components with high content of Ir4+ species, more precisely 36:64 wt.% of Ir0:Ir4+ and 2:98 wt.% of Ir0:Ir4+. The cycling up to 1.4 VRHE shows mainly a reversible behavior due to high content of Ir4+ species on TiO2. With increasing anodic potential, the content of metallic Ir further decreases and the main component with almost only Ir4+ species is stable at 1.4 VRHE. In the backward direction, the reduction to metallic Ir takes place to small extent. Therefore, the component with 36:64 wt.% of Ir0:Ir4+ is mainly present at 0.06 VRHE.In summary, our PCA and LCF analysis of the operando and dynamic Quick-XANES data provide further insights into the electronic structure of Ir species and the mechanism of the complex metal-support interaction for Ir NPs immobilized on C, ATO and TiO2.

Probing the Electrode-Liquid Interface Using Operando total-Reflection X-Ray Absorption Spectroscopy

Traditional operando methods to study electrochemical (EC) processes, although successful, are based on EC measurements, lacking in direct sensitivity of chemical and structural changes. A fundamental understanding of the underlying mechanism occurring during an EC reaction could allow to improve performances and properties of applied material systems. EC processes are localized at the electrode-electrolyte interfacial regions, but several surface sensitive experimental techniques are often limited to ex situ conditions, owing to the need of a Ultra High Vacuum (UHV) environment, e.g., Scanning Tunneling Microscopy (STM), X-ray Photoelectron Spectroscopy (XPS), Low Energy Electron Diffraction (LEED), etc.1 On the contrary, synchrotron-based hard x-rays provide an intense and highly energetic source that can penetrate the electrolyte without undergoing significant attenuation. Furthermore, the x-ray beam can be focused on a flat metal surface adopting a grazing incidence geometry, increasing surface sensitivity up to a few nanometers in subcritical condition. The latter case is achieved when the incident angle is set below the critical angle for total external reflection (TER), characterized by the occurrence of an evanescent wave confined at the surface. As a result, x-ray photon-in photon-out techniques can be used to probe the electrode-liquid interface in working conditions.2,3 In this contribution, we performed operando Grazing Incidence X-ray Absorption Spectroscopy (GI-XAS) in total external reflection (TER) mode4 (Fig. 1) at P64 (DESY, Hamburg), using our EC setup designed for multimodal studies with hard x-ray scattering and spectroscopy techniques3. XAS can provide unique information about the local chemical and structural environment of absorbing atoms during electrochemical polarization. The electro-oxidation of polycrystalline gold, relevant for the understanding of electrolysis, and the surface passive film development and breakdown of Ni-Cr-Mo corrosion resistant alloys, have been investigated. Despite the presence of the electrolyte and the PEEK walls of the EC cell, 1-3 nm thick surface oxides film can be detected in TER mode using energies down to 8 keV. Advantages and challenges of this method will be discussed showing experimental results. Figure 1 Left: Schematic of our EC cell showing sample geometry for GI-XAS in TER mode, the incidence angle q is always lower than the critical angle. Right: GI-XAS in TER mode from a Ni 59 alloy sample at the Ni k-edge at increasing EC polarization in 1M NaCl and pH 12. Maurice, V. Progress in corrosion science at atomic and nanometric scales. Progress in Materials Science 40 (2018).Timoshenko, J. & Roldan Cuenya, B. In Situ / Operando Electrocatalyst Characterization by X-ray Absorption Spectroscopy. Chem. Rev. 121, 882–961 (2021).Långberg, M. Redefining passivity breakdown of super duplex stainless steel by electrochemical operando synchrotron near surface X-ray analyses. npj Materials Degradation, 3(1): p. 22. (2019).D. Gajdek. Structural Changes in Monolayer Cobalt Oxides under Ambient Pressure CO and O 2 Studied by In Situ Grazing-Incidence X-ray Absorption Fine Structure Spectroscopy, J. Phys. Chem. C, vol. 126, n. 7, pagg. 3411–3418 (2022) Figure 1

Does Anisotropic ‘Lattice’ Collapse Always Lead to Cracking in Ni-Rich Layered Oxide Cathode Particles?

Single-crystalline Ni-rich layered oxides (LiNi x Mn y Co1−x−y O2; x ≥ 0.8) are promising high-energy-density cathodes for future Li-ion batteries as they can withstand cathode particle cracking, which is a significant contributor to electrochemical capacity loss. The absence of grain/particle boundaries substantially mitigates the build-up of bulk structural strain in these materials generated from the anisotropic structural evolution (i.e., lattice collapse) during electrochemical cycling. However, compared to their polycrystalline counterparts, rigorous evaluations of their long-term electrochemical performance and their dependence on electrode structure changes, impedance, and particle cracking, are still necessary to take it towards commercialisation. Operando X-ray diffraction (XRD) and absorption spectroscopy (XAS) are ideal probes of these bulk electrode structure properties and provide a direct temporal correlation between the battery electrochemistry and the non-equilibrium structural changes in the electrodes. However, such studies often use electrochemically compromised cells modified for X-ray transmission that are neither representative of a real-world full-cell architecture nor operable long-term under industrially relevant cycling conditions, thereby compromising the results' practicality. This is especially problematic for technologically mature cathodes like single-crystalline Ni-rich layered oxides, which require greater scrutiny of their long-term degradation modes after hundreds of cycles. In this work, using in-house operando X-ray studies and large-area post-mortem electron tomography of a (TRL-5) pilot-line-built A7 pouch full cells with industry-relevant specifications, we demonstrate how single-crystalline LiNi0.8Mn0.1Co0.1O2 (NMC811) cathodes can withstand the severe anisotropic structural evolution and show no particle cracking even when cycled under harsh conditions of 2.5–4.4 V at 40 °C for 100 cycles. The bulk structural changes in both electrodes as well as the associated electrochemical performance loss are also evaluated. Furthermore, the validity of the in-house pilot line cell results is benchmarked against a commercially sourced Li-ion cell. In addition to furthering our understanding of single-crystalline Ni-rich cathodes, this work emphasises the need for real-world-relevant reproducible fundamental investigations of academic Li-ion cells and presents a methodology for doing so. Figure 1

Operando High-Temperature X-Ray Absorption Spectroscopy of LiNiO2 Cathode Material during Synthesis

The increasing demand for higher energy density in batteries for automotive applications has led to a trend toward increasing the Ni content in layered oxide cathode materials to increase their reversible capacity. However, LiNiO2, which has the highest Ni content, shows a faster capacity drop during charge-discharge cycling, which is attributed to its inherent structural instability in both the pristine and delithiated states. Therefore, to address the former issue and to better understand the appropriate synthesis conditions for LiNiO2, we have studied the changes in the local structure of LiNiO2 during the synthesis process using operando analysis techniques. Recently, high temperature in situ X-ray diffraction during LiNiO2 synthesis was reported by Bianchini [1] and Weber [2], which confirmed the loss of lithium and oxygen and the migration of Ni to Li layers above 700 °C. To further understand the mechanism of Li/Ni mixing and oxygen loss, operando high-temperature X-ray absorption spectroscopy (XAS) was performed during the synthesis of LiNiO2 to clarify the electrical structure of Ni at high temperatures. Pre-heated Li x NiO2 (x = 0.76, 1.01, 1.26, and 1.51) precursors were prepared by heating LiOH·H2O and Ni(OH)2 at 480 °C for 24 h in air. The precursor was pelletized and set in a quartz sample holder. Operando high-temperature Ni K-edge XAS spectra of the precursor were obtained at BL9A and BL12C in Photon Factory (PF), High Energy Accelerator Research Organization (KEK) by a transmission mode. The operando spectra of all samples except Li/Ni = 0.76 revealed a clear edge shift to the lower energy side corresponding to nickel reduction above 700 °C. The Li/Ni = 0.76 sample has a lithium-deficient composition and Ni is not oxidized to Ni3+ below 700 °C, so the Li/Ni = 0.76 sample has almost no Ni K-edge energy shift above 700 °C. These results suggest that Ni in LiNiO2 is reduced above 700 °C even in an oxygen atmosphere, regardless of whether the Li/Ni ratio is greater than 1. The Ni reduction above 700 °C is probably the cause of the Li/Ni mixture.Reference[1] M. Bianchini, J. Janek, et al., Angew. Chem., Int. Ed., 58, 10434 (2019).[2] R. Weber, J. R. Dahn, et al., J. Electrochem. Soc., 167, 100501 (2020).

Effect of Electrolyte Anions on the Activity of Iridium Oxide Catalysts for Water Electrolysis

Developing environmentally friendly and renewable energy sources is essential due to the environmental and energy security issues caused by traditional combustion of fossil fuel-based energy sources. Therefore, as a clean and sustainable energy carrier, hydrogen has attracted great attention in recent years. In this regard, water electrolysis utilizing renewable energy sources to produce hydrogen is considered one of the most promising technologies. It is believed elucidation of the reaction mechanism of highly active iridium oxides is promising for the further development of cost-efficient PEM water electrolysis catalysts. The properties of the MEA could be affected by many parameters such as the catalysts, operating temperature, and pressure1,2. Another important factor is the cation impurities that can be found in the circulating water, which could severely degrade the MEA performance during the operation of a PEM water electrolyze. However, there are less reports on anion impurities such as SO4 2- and PO4 3-. Therefore, in this study, the relationship between electrolyte anions and OER activity was investigated for IrOx catalysts with different crystal structure. By using operando X-ray absorption spectroscopy (XAS), we investigated the electronic state of Ir and O under operation potential.IrOx with different degree of crystallinity (SA3.5 and SA58) were provided by Tanaka Kikinzoku Kogyo K.K., Chemical & Refining Company and named after their BET surface areas. These two samples were then tested for electrochemical properties in different concentrations of phosphoric acid and perchloric acid, respectively. The electrochemical measurements were performed using a standard three-electrode cell connected to an MPG-205-NUC system (Bio-Logic). The cyclic voltammograms (CV) were scanned from 0.1 V to 1.2 V vs. RHE at 50 mV s-1. The electrochemical activities of the catalysts were subsequently investigated using linear sweep voltammetry (LSV) in the range of 1.1 to 1.7 V vs RHE at 10 mV s−1. operando XAS were collected using a home-made flow-type cell, where Pt wire and RHE worked as counter and reference electrodes, respectively. The catalyst ink was coated onto an Nafion membrane to prepare both the X-ray window and working electrode. The electrolyte was circulated at the flow rate of 100 mL min-1.The catalytic performance of IrOx was investigated at different types and content of electrolyte under H3PO4 and HClO4. Figure 1 shows the CVs of SA3.5 and SA58 under different types and content of electrolyte. In the presence of phosphate anions, SA3.5 showed a tendency to decrease Ir redox between 0.6 and 1.1 V with increasing electrolyte concentration. On the other hand, there were no obvious changes in SA58. It was found that IrOx catalysts have an great effect of specific adsorption of anions and low symmetry of monoclinic phase catalysts (SA 3.5) are more susceptible to anion poisoning. Figure 2 shows the result of examining the poisoning mechanism using soft X-ray XAS. O K-edge results present the formation of µ2-O (O-O) bond at around 528.7 eV, which was previously observed by Nong, H. N. et. al. through operando O-K edge measurements during OER process3. The peak intensity at 528.7 eV of the amorphous samples was in the same order as the OER activities. According to potential dependence change of the pre-edge peak, under the presence of phosphate anions, the hole formation to Ir-O hybrid orbitals was suppressed in SA3.5. This result indicates that the anion adsorbs to the active site, poisoning the catalyst surface and inhibiting the reaction. Acknowledgements This work is based on results obtained from a project (JPNP14021) commissioned by the New Energy and Industrial Technology Development Organization (NEDO) of Japan. References Zhang, Y.; Zhu, X.; Zhang, G.; Shi, P.; Wang, A.-L.; et al. J. Mater. Chem. A: 2021, 9, 5890-5914.Chen, Z.; Duan, X.; Wei, W.; Wang, S.; Ni, B.-J.; et al. Nano Energy: 2020, 78, 105270.Nong, H. N.; Falling, L. J.; Bergmann, A.; et al. Nature 2020, 587 (7834), 408-413. Figure 1

Trapped Platinum Single-Site Catalysts for the Hydrogen Evolution Reaction

Trapped platinum single-site catalysts (Pt-SSCs) in defective carbon substrates are of particular interest for polymer-electrolyte membrane (PEM) water electrolysers due to their high Pt atom utilization for the hydrogen evolution reaction (HER). However, their intrinsic catalytic activity compared with metallic Pt nanoparticles remains a topic of debate in the field with opposing results reported. [1, 2] A detailed investigation of the bonding environment of Pt and its evolution at HER working conditions is therefore warranted in order to corelate the Pt single-site structure to its catalytic activity and stability.Here, we present a detailed analysis on trapped Pt-SSC prepared by pyrolysing H2PtCl6 adsorbed on a polyaniline substrate. [3] We used in-situ heated scanning transmission electron microscopy, temperature-dependent X-ray photoelectron spectroscopy and operando X-ray absorption spectroscopy to follow the evolution of Pt’s bonding environment during pyrolysis and HER. We demonstrate that the trapped Pt-SSC is stable under HER potentials but with lower catalytic activity relative to commercial Pt nanoparticles. We also perform first principles calculations to elucidate the origin of the inferior activity.Our results promote the understanding of the relationship between the structure of trapped Pt-SSC and its HER performance, and calls for a techno-economic analysis to assess the practicality of using Pt-SSCs in commercial PEM water electrolyzers.References Q. Yang, H. Liu, P. Yuan, Y. Jia, L. Zhuang, H. Zhang, X. Yan, G. Liu,Y. Zhao, J. Liu, S. Wei, L. Song, Q. Wu, B. Ge, L. Zhang, K. Wang, X. Wang, C.-R. Chang, and X. Yao, J. Am. Chem. Soc., 144, 2171 (2022).J. Wang, H. Y. Tan, T. R. Kuo, S. C. Lin, C. S. Hsu, Y. Zhu, Y. C. Chu, T. L. Chen, J. F. Lee, and H. M. Chen, Small, 17, 2005713 (2021).P. Tang, P.-Y. Huang, J. E. N. Swallow, C. Wang, D. Gianolio, H. Guo, J. H. Warner, R. S. Weatherup and M. Pasta, “Structure- property relationship of defect-trapped Pt single-site electrocatalysts for the hydrogen evolution reaction” Reasearch Square (2023), doi: 10.21203/rs.3.rs-2397818/v1.

Operando XAS Investigation of Bimetallic Iron−Molybdenum Sulfide Electrocatalysts for the Hydrogen Evolution Reaction

Nowadays green hydrogen production has been seen as a key element for the future development and large-scale implementation of fuel cell technology, while electrolyzer technologies represent the most advanced methods for producing pure hydrogen from water. The preparation of efficient, cost-effective, and stable noble-metal-free electrocatalysts for the hydrogen evolution reaction (HER) at the cathode of proton exchange membrane electrolyzers (PEMEL) remains one of the main issues that need to be solved to allow the widespread use of hydrogen as an energy carrier.Molybdenum sulfide (MoSx) is a well-known material showing promising HER catalytic activity, especially in its amorphous state and when doped with other transition metals1. The successful implementation of a bimetallic iron-molybdenum sulfide electrocatalyst for HER into a PEM electrolyzer has been recently reported2. However, the structure of their active sites requires a more elaborate investigation. In this study, we employed operando X-ray absorption spectroscopy to identify potential-induced structural and electronic changes in FeMoSmw bimetallic iron−molybdenum sulfides and MoSmw obtained by a microwave irradiation synthetic approach 2. Extended X-ray absorption fine structure (EXAFS) spectra at Mo and Fe K-edges under operando conditions provided us with accurate structural characterization of the catalytic active sites: while an amorphous MoS3 phase is detected and retained in both MoSmw and FeMoSmw at low potential, a FeS phase is observed at the Fe K-edge, likely explaining the better performance of the bimetallic iron-molybdenum sulfides electrocatalysts compared to iron-free molybdenum sulfides.

Unintended Cation Crossover in CO2 Conversion MEA Cells: Causes and Effects

Membrane electrode assemblies in gas diffusion cells enable CO2 reduction at industrially relevant rates, yet their long-term operational stability is often limited by the formation of solid precipitates (e.g. K2CO3) in the cathode pores. This is a consequence of a combination of 1) local alkalization due to the electrochemical reaction, 2) generation of (bi)carbonate by chemical reaction of CO2 with the alkaline electrolyte, and 3) the presence of alkali metal cations. In catholyte-free, zero-gap cells using anion exchange membranes, the presence of electrolyte cations at the cathode is the result of unintended crossover from the anolyte, and a detailed understanding of the factors enabling this crossover is lacking. Here we show that the anolyte concentration governs the flux of cation migration through the membrane, and this substantially influences the behaviors of copper catalysts in catholyte-free CO2 electrolysers. Systematic variation of the anolyte ionic strength (using aqueous KOH or KHCO3) correlated with drastic changes in the observed product selectivity – most notably, at low ionic strength, Cu catalysts produced predominantly CO, in contrast to the mixture of C2+ products typically observed on Cu. In this talk, we examine the factors influencing ion crossover and the resulting effects on catalyst structure and activity, under conditions of both CO2 and CO reduction. Operando X-ray absorption spectroscopy and quasi in situ X-ray photoelectron spectroscopy were used to study how the catalyst is affected by operation conditions. Our results show that even in catholyte-free cells, cation effects (including unintended ones) can significantly influence reaction pathways, and this must be considered in future development of catalysts and devices.El-Nagar, G. A., Haun, F., Gupta, S., Stojkovikj, S. & Mayer, M. T. Unintended cation crossover influences CO2 reduction activity in Cu-based zero-gap electrolysers. Nature Communications14, 2062 (2023) doi: doi.org/10.1038/s41467-023-37520-x Figure 1

Temperature-Dependent Interplay of Chemical Versus Electrochemical Electrolyte Oxidation at Ni-Rich Cathodes

Increasing demands for high energy density Li-ion batteries as a source for power supply are demanding an optimization of cathode active materials (CAMs) and of the overall cell chemistry of batteries. Thus, the main interest of researchers has focused on nickel-rich (>80%) layered transition metal oxides such as NCMs (LiNixCoyMnzO2, with x+y+z=1) or NCAs (LiNixCoyAlzO2, with x+y+z=1) as CAMs, owing to their high capacity. However, as a result of the increase in Ni-content, the structural stability of these CAMs is significantly decreased at high upper cut-off potentials compared to those with lower Ni-content, resulting in capacity fading, which restricts their practically achievable capacity.[1] One possible culprit behind this capacity fading at high state-of-charge (SOC) is the release of reactive lattice oxygen, which is known for layered TM-oxides to occur at high SOC (i.e., starting at approx. 80% SOC).[2] The released oxygen is proposed to lead to the chemical oxidation of ethylene carbonate (EC), resulting in HF formation, which in turn is proposed to trigger the dissolution of TMs.[3] Furthermore, the electrochemical oxidation of the electrolyte is known to occur at high potentials, which as a result of its reactive reaction products, can induce further transition metal (TM) dissolution from the CAM.[4,5] The proposed chemical oxidation of the electrolyte by lattice oxygen suggests that this process should be strongly correlated to the dissolution of TMs from the CAM. However, as shown by operando X-ray absorption spectroscopy (XAS) and on-line electrochemical mass spectroscopy (OEMS) studies, the onset for the TM-dissolution, depending on the CAM under investigation, occurs at ~300 mV higher potentials compared to the onset for oxygen evolution.[2,3] This suggests that the dissolution of metals is rather induced by the electrochemical oxidation of the carbonate-based electrolyte, which was reported to initiate at potentials above 4.7 VLi at room temperature.[5] Both the electrochemical oxidation of battery electrolytes, as well as the dissolution of TMs from the CAM were reported to be strongly affected by temperature, while the onset potential for lattice oxygen loss is essentially unaffected, which further hints towards the significance of former.[5-7] Within this work we therefore conduct a detailed study on the temperature dependency of both the gas formation due to (electro)chemical electrolyte oxidation and the dissolution of TMs by means of OEMS and operando hard XAS, respectively. By applying a measurement protocol consisting of constant voltage-holds in steps of 50 mV at elevated potentials (see Figure 1), an excellent time as well as potential resolution enables the deconvolution of the onset for lattice oxygen release and the (electro)chemical oxidation of LP47 (1 M LiPF6 in EC:DEC 3:7 by weight) for a LiNi0.80Co0.15Al0.05O2 (NCA) CAM via OEMS. It will be shown that the onset for oxygen evolution coincides with a significant evolution of CO2 (see Figure 1b), indicating chemical oxidation of the electrolyte. However, the onset for POF3/PF5 evolution (marked in Figure 1b as “POF3”, since both gasses appear on the same mass channel)[8], which is a reaction product from the decomposition of LiPF6 caused by electrochemical electrolyte oxidation, is shifted to 300 – 450 mV higher potentials (depending on the temperature). It suggests a chemical oxidation mechanism of the electrolyte, which proceeds without significant H2O/H+ production. A change in temperature strongly affects this onset of “POF3” evolution, while O2 is released at the same degree of de-lithiation, regardless of temperature. To correlate this effect observed in the temperature-dependent gassing behavior to the dissolution of transition metals for this CAM, an operando hard XAS study at different temperatures will be conducted.

Operando Investigations of Reversible and Irreversible Transformations of Metal Organic Framework Based Catalysts during the Oxygen Evolution Reaction

Intermittency issues due to the growth of renewable energy usage lead to an increasing interest in energy storage systems. Thereby, one can use the excess energy for the production of hydrogen from water by anion exchange membrane (AEM) water electrolysis using earth-abundant, non-noble metal catalysts. However, the kinetics of the oxygen evolution reaction (OER) limit the activity of the catalyst and hence, the development of performance stable and active OER catalysts is of great importance for the commercialization of AEM water electrolyzers. In metal organic frameworks (MOFs), a porous structure is created by linking metal atoms/clusters with other metal centres using organic ligands. The resulting structure with a high surface area and dispersed metal centres is a promising catalyst for OER.MOF catalysts with Ni and Co metal centres show impressive OER activity. Both, Co-MOF-74 and Ni-MOF-74 exhibit higher OER activity than their oxide counterparts produced by flame spray synthesis in form of nanoparticles (Fabbri (2017) and Abbott (2018)).1,2 Thereby, an increasing OER activity of Ni-MOF-74 during rotating disk electrode stability tests, indicates that the catalytic species undergoes favorable electronic and structural transformations.Using an in-house-developed spectro-electrochemical flow cell, these transformations were studied by operando X-ray absorption spectroscopy (XAS) and X-ray diffraction (XRD). Operando XAS enabled us to monitor the changes occurring in the Ni metal centers while performing cyclic voltammetry (CV) from 1 VRHE up to potentials above the OER onset potential with a time resolution of 5 sec. The operando XAS measurements show that Ni-MOF-74 develops into a highly OER active and stable catalytic species. However, operando XRD measurements prove that the crystalline MOF structure changes into an amorphous structure during OER. Monitoring the electronic and structural transformations due to potential cycling, three different structures were extracted: an initial state, which disappeared within the first eight CV cycles, and two novel electronic/local structures appearing at low and high potential, respectively. The transformations in the electronic and local structure of the Ni metal centers occurring between low and high potential appear to be reversible, as the Ni metal centers return to their initial state during long-term storage in air. However, XRD measurements indicate that this further transformation does not affect the structure of the catalyst: Even though the Ni centers return to their original local structure and oxidation state after long-term storage in air, the long-range structure stays amorphous.The study focuses on elucidating the structure-performance relations of Ni-MOF-74 based OER catalysts providing the key structural parameters that lead to the formation of the highly OER active species. The mechanism of reversible and irreversible transformations occurring in Ni-MOF-74 catalysts allows the extraction of activity descriptors for the development of highly OER active and stable non-noble metal catalysts for AEM water electrolysis.