Open Window Research Articles

Effects of Wearing Personal Protective Equipment on Serum Cortisol Levels and Physiological Variables in Healthcare Workers: A Randomised Controlled Trial in a Simulated Pandemic Environment.

The COVID-19 pandemic has necessitated the widespread use of personal protective equipment (PPE), particularly in high-risk environments. Full-body PPE is favoured for its comprehensive protection against the virus but poses challenges to the body's thermoregulatory system as it inhibits air exchange. This randomised trial was undertaken to investigate the effects of wearing a commonly used gown-type full-body PPE kit in a simulated environment. Initially, 65 healthy males were recruited and randomly divided into two groups: a study group wearing a full-body PPE kit (gown-type, full-body PPE kit with trousers, a gown-type shirt with a hood, a shoe cover, an N95 face mask, and an optional face shield) and a control group without PPE. They remained seated for three hours while wearing the PPE kit. Room conditions mimicked non-air-conditioned hospital scenarios, with temperature and humidity recorded and ventilation provided through open doors and windows, along with ceiling fan cooling. Activities with minimal physical exertion were allowed, and access to the toilet was kept to a minimum. Subjects underwent assessments of heart rate, respiratory rate, temperature, blood pressure, heart rate variability (HRV), and blood samples for serum cortisol before donning the PPE kit and entering a simulated ICU/WARD environment and after doffing. A total of 60 participants completed the study (30 in each group). Compared to the controls, serum cortisol levels significantly increased in the PPE groups, and HRV data indicated increased sympathetic activity in the PPE group. Wearing a full-body PPE kit (gown-type upper garment with trousers) was found to have a significant impact on cortisol levels and physiological variables in a simulated environment. This suggests that in situations like the COVID-19 pandemic that warrant the use of such PPE kits, appropriate measures should be taken to provide better thermal stability for maintaining the well-being of healthcare workers.

Experimental Measurements in Schools with Natural Ventilation

Abstract Facilities for children and young people should be established in a healthy environment that is protected from external health-damaging factors, such as noise, air pollution, and negative educational influences. A school building should also be a safe and healthy environment for pupils and students, as legally required. However, although some school buildings have been renovated, most were constructed in the last century, and their indoor microclimate remains unsatisfactory. Schools must maintain optimal thermal and humidity conditions to ensure the healthy development of children and their ability to function properly in a classroom. While natural ventilation through opening windows is a good practice, it may not always guarantee sufficient air exchange, especially for schools located in busy traffic areas. This paper presents experimental measurements and a comparison between two primary schools in Bratislava, which describes the current thermal and humidity conditions in the indoor environment of both schools. Experimental measurements were carried out on five school days in each primary school to determine the thermal-humidity conditions and indoor air quality, depending on the concentrations of carbon dioxide.

A poetics of opacity: disability, race and gender in Khady Sylla’s Une fenêtre ouverte

ABSTRACT Une fenêtre ouverte/An Open Window (2005), a documentary by the Senegalese writer and filmmaker Khady Sylla, offers an intimate, unsettling portrait of the mental health difficulties suffered by both Sylla and her friend, Aminta Ngom. This article reads Sylla’s film as embracing Black female disabled subjectivities that have been historically constructed – through intersecting patriarchal, colonialist and ableist regimes – as abject or aberrant. While scholarship on Sylla’s film has addressed ideas of female madness, it has not engaged with (Black feminist) disability studies – a critical lacuna addressed here. Drawing on ideas of opacity (Glissant), ‘mad methodology’ (Bruce) and Black feminist disabled perspectives that question emancipatory or healing coherence (Pickens, Nack Ngue), the article reads Sylla’s film in terms of a poetics of opacity that opens to a cripping of cinematic time and space. While focusing on a relationship of female friendship, solidarity and care that offers refuge from fraught familial dynamics, the film’s empathy is capacious, extending to Aminta’s mother and daughter too. As Une fenêtre ouverte traces the tensions that structure these various relationships, it reveals its feminist approach, its mode of feeling in solidarity, to be one that embraces strategies of opacity and ethical ambiguities.

The effect of islamic ornament as secondary skin on daylight quality

Abstract Islamic ornaments are used extensively in different types of buildings, serving both aesthetic and functional purposes. They are used in mosques, offices and other buildings, serving as both interior and exterior elements. One application is their use as secondary skins to cover window openings. This research investigates the effect of Islamic ornaments as secondary skins on interior lighting. The main question addressed is how Islamic ornaments affect the quality of natural lighting. Using computer simulations, scenarios with clear glass and varying ornament distance from the window were assessed under clear sky conditions at different times of the day. The results show that the presence of Islamic ornaments significantly reduces the average daylighting level on interior surfaces compared to scenarios without ornaments. Visual representations using ray diagrams and computer-generated images illustrate the effects of varying ornamental conditions. This research highlights the potential of Islamic ornaments to improve the quality of daylighting in architecture. The findings emphasise their role in optimising daylight indoors, and encourage careful consideration of the impact of spacing on window openings. In particular, the distribution of daylight varies between rooms orientated to the north and west.

Single Lung Transplantation After Open Window Thoracotomy for Empyema: A Case Report

A 41-year-old woman with lymphangioleiomyomatosis developed a bronchial anastomotic stenosis after left single lung transplantation (LTx). A part of the hyperinflated right native lung was excised in an attempt to remedy the left lung compression, which appeared to affect the bronchial anastomotic stenosis and ventilation/perfusion mismatch. However, a persistent air leak after the surgery caused empyema and an open window thoracotomy (OWT) was performed. She remained oxygen-dependent and was relisted for lung transplantation. A right single LTx on the side of OWT was performed, achieving long-term survival with no activity limitations for the patient. We report here the first successful LTx after OWT for empyema.

Analyzing the opening and closing of windows in residential for predicting the energy consumption using optimized multi-scale convolution networks

PurposeThis proposal aims to forecast energy consumption in residential buildings based on the effect of opening and closing windows by the deep architecture approach. In this task, the developed model has three stages: (1) collection of data, (2) feature extraction and (3) prediction. Initially, the data for the closing and opening frequency of the window are taken from the manually collected datasets. After that, the weighted feature extraction is performed in the collected data. The attained weighted feature is fed to predict energy consumption. The prediction uses the efficient hybrid multi-scale convolution networks (EHMSCN), where two deep structured architectures like a deep temporal context network and one-dimensional deep convolutional neural network. Here, the parameter optimization takes place with the hybrid algorithm named jumping rate-based grasshopper lemur optimization (JR-GLO). The core aim of this energy consumption model is to predict the consumption of energy accurately based on the effect of opening and closing windows. Therefore, the offered energy consumption prediction approach is analyzed over various measures and attains an accurate performance rate than the conventional techniques.Design/methodology/approachAn EHMSCN-aided energy consumption prediction model is developed to forecast the amount of energy usage during the opening and closing of windows accurately. The emission of CO2 in indoor spaces is highly reduced.FindingsThe MASE measure of the proposed model was 52.55, 43.83, 42.01 and 36.81% higher than ANN, CNN, DTCN and 1DCNN.Originality/valueThe findings of the suggested model in residences were attained high-quality measures with high accuracy, precision and variance.

An online method for ship trajectory compression using AIS data

Abstract Vessel trajectories from the Automatic Identification System (AIS) play an important role in maritime traffic management, but a drawback is the huge amount of memory occupation which thus results in a low speed of data acquisition in maritime applications due to a large number of scattered data. This paper proposes a novel online vessel trajectory compression method based on the Improved Open Window (IOPW) algorithm. The proposed method compresses vessel trajectory instantly according to vessel coordinates along with a timestamp driven by the AIS data. In particular, we adopt the weighted Euclidean distance (WED), fusing the perpendicular Euclidean distance (PED) and synchronous Euclidean distance (SED) in IOPW to improve the robustness. The realistic AIS-based vessel trajectories are used to illustrate the proposed model by comparing it with five traditional trajectory compression methods. The experimental results reveal that the proposed method could effectively maintain the important trajectory features and significantly reduce the rate of distance loss during the online compression of vessel trajectories.

INVESTIGACIÓN BIOMÉDICA EN CHILE: APRENDIZAJE EN 48 AÑOS DE DIÁLOGO CON LAS PLAQUETAS

Biomedical research in Chile is necessary, it positions us at the limit of knowledge and improves the quality, accreditation and ranking of the academic institutions where it is developed. Its financing requires the political commitment regarding its importance for our country and of academic institutions to create a protective microenvironment for its flourishment. Private companies have consistently increased their contribution to R&D, but understandably, with a smaller presence in biomedicine. Specific competencies of the investigators may be highly useful and decisions regarding introduction of new products and technologies in clinical and laboratory grounds. Despite the remoteness of the major research centers, our work will be relevant if we overcome our objective limitations with creativity and extra effort. These include available resources, considering that the fraction of GDP budget for R&Din OCDE countries is 8 times higher than ours; proficiency in English language is a major problem for many of us; establishing trusting relationships with leading researchers in the field is a pre-requisite to grant our insertion in major scientific societies and for creating international collaborations; eagerly evaluate and use the transiently open windows for research; use the benefits of comparative advantages or unique conditions in Chile that enhance the originality of our studies; as phy­sicians, we have privileged access to patients for descriptive or mechanistic studies, including technical advantages, lower cost, and higher appraisal in scientific journals. We will expand on these considerations in our presentation.

The Underlying Mechanism of Poisoning after the Accidental Inhalation of Aerosolised Waterproofing Spray.

Waterproofing sprays can cause acute respiratory symptoms after inhalation, including coughing and dyspnoea shortly after use. Here, we describe two cases where persons used the same brand of waterproofing spray product. In both cases the persons followed the instructions on the product and maximized the ventilation by opening windows and doors; however, they still became affected during the application of the product. Products with the same batch number as that used in one case were tested for their effect on respiration patterns of mice in whole-body plethysmographs and lung surfactant function inhibition in vitro. The product was used in spraying experiments to determine the particle size distribution of the aerosol, both using a can from one case and a can with an identical batch number. In addition, the aerosols in the mouse exposure chamber were measured. Aerosol data from a small-scale exposure chamber and data on the physical and temporal dimensions of the spraying during one case were used to estimate the deposited dose during the spraying events. All collected data point to the spraying of the waterproofing product being the reason that two people became ill, and that the inhibition of lung surfactant function was a key component of this illness.

Validation of Dynamic Natural Ventilation Protocols for Optimal Indoor Air Quality and Thermal Adaptive Comfort during the Winter Season in Subtropical-Climate School Buildings

The need for energy-efficient buildings must be based on strong effective passive-design techniques, which coordinate indoor air quality and thermal comfort. This research describes the principles, simulation, implementation, and monitoring of two different natural cross-ventilation algorithm scenarios applied to a school-building case study affected by a subtropical climate during the winter season. These ventilation protocols, the steady and dynamic versions, can control the carbon dioxide concentration and actuate the window openings according to pre-defined window-to-wall ratios. The implementation of the monitoring process during three non-consecutive days in the winter of 2021 validates the opening strategy to maintain carbon dioxide below 800 ppm, described by the protocol Hygiene Measures Against COVID-19, and the temperature within the comfort ranges suggested by the adaptive UNE-EN 16798. The study shows that a steady opening of 2.16% window-to-wall equivalent ratio can be enough to maintain the requested comfort and carbon dioxide conditions. The use of the dynamic window ratios, from 0.23% to 2.16%, modified according to the measured carbon dioxide concentration, can partially maintain the carbon dioxide below the required limits for ASHRAE 62.1, Hygiene Measures Against COVID-19 and UNE-EN 16798 between 48.28% to 74.14% of the time. However, the carbon dioxide limit proposed by RITE, 500 ppm, is only achieved for 15.52% of the time, which demonstrates the inadequacy of the natural ventilation to fulfil the standard. Further improvements in the dynamic control of the openings in these buildings could lead to lower carbon dioxide concentrations while maintaining the thermal comfort in mild winter climates.

The diffusion process of different moisture sources in the radiant cooling room and the condensation risk assessment

The condensation phenomenon severely limits the widespread application of radiant cooling systems. Although a series of anti-condensation methods have been proposed, it is more important to explore the diffusion process of moisture sources that cause condensation in the radiant cooling room, only in this way can targeted anti-condensation measures be carried out. In this regard, the numerical simulation method is used to explore the diffusion process of additional moisture caused by the increase in occupancy rate and window opening behavior, while monitoring the state of the air on the surface of the radiant terminal (ASRT) to determine whether condensation occurs and evaluate the condensation risk. The results indicate that the moisture emitted by the increased personnel will diffuse along the direction of their surface hot air flow when the occupancy rate increases, and the moisture in the outdoor air will diffuse along its flow direction after the window is opened. However, the change of moisture is accompanied by the change of heat and the condensation phenomenon will not occur first in the place with a large humidity ratio, but rather in areas with lower surface air temperatures in these two situations. In addition, condensation will not occur in all cases after the occupancy rate increases, and the minimum condensation time is still more than 20 min when the occupancy rate is maximum, which has sufficient time for human intervention to avoid condensation. Condensation occurs in all cases after the window is opened, with a minimum condensation time of 68 s. Window opening behavior carries a high condensation risk and should be avoided during the operation of the radiant cooling system. This study can provide a basis for adopting corresponding anti-condensation strategies.

Influence of window and door opening on office room environment and human thermal sensation during different seasons in moderate climate

Natural ventilation is commonly used in buildings because it does not require energy, and its various strategies, for example ventilation through an open window, can improve the indoor environment quality, including the thermal comfort of users. This study aimed to determine accurate environmental parameters typical for naturally ventilated rooms for three seasons: summer, autumn and winter, and to assess the occupants' thermal sensation in the mentioned conditions. Based on the measurements, the spatial distribution and time variability of air temperature and air speed in an office room with a stack natural ventilation system were assessed. The resulting data on the indoor environment parameters at different seasons and with various door and window opening configurations were used as an input to simulate human thermal sensation. Three models were used for simulation: predicted mean vote (PMV), the thermal sensation (TS) model developed by Zhang et al., and the advanced dynamic thermal sensation (DTS) model by Fiala et al., which allowed the demonstration of differences in the thermal comfort assessment depending on the method. Measurements have shown that opening the window with the door closed has a negligible impact on the parameters indoor environment parameters in summer; opening the door (cross-ventilation) changes this situation. The effect increased during autumn and winter, which affects users' thermal sensations. The assessment based on the most popular PMV model differed from the indications of advanced DTS and TS models showing significant discrepancies, which may lead to a misinterpretation of thermal comfort for individuals in the room.

Tackling of challenging accessory pathways utilizing open window mapping, does it add benefit?

Abstract Introduction 3D electroanatomical mapping is beneficial in accessory pathway ablation for better delineation of the anatomy, less procedure and fluro time, it depends on point-by-point mapping to identify the connection sites of the accessory pathway (AP) to the atria or ventricle, or the site of the AP potential. However, this approach requires an accurate interpretation of the local electrograms. In contrast, open window mapping (OWM) doesn’t need to differentiate the signals site of origin, it is based on an automatic annotation process in which the signals with the highest -dV/dt are annotated at each obtained point irrespective of the cardiac chamber. (1) Few reports describe the additional benefit of such technique in patients with complex congenital heart diseases. (2) Purpose To present our centre experience in using OWM technique in addition to early meets late (EML) algorism in accessory pathway ablation especially in patients with complex congenital heart disease or previous failed ablation trials. Methods We reviewed patients who underwent AVRT ablation at our centre from August 2022 to August 2023 with emphasis on cases mapped using OWM & EML techniques using high density mapping catheters. Demographic data, clinical presentation, resting & tachycardia ECGs, and Echo reports were examined thoroughly, additionally, we revised the 3D maps, ablation details, fluro dose, and outcomes of the procedures. Results Over one year, among 74 patients underwent AVRT ablation, open window mapping was used in 4 patients with manifest preexcitation (Rt posteroseptal in 3 of them & Rt free wall in one patient). Among the four patients: 3 were pediatrics, youngest was 5 years old, 19 Kg, 2 patients had previous failed ablation trials, their Echo reports revealed severe form of Ebstein anomaly with large ASD in the first patient, case 2 had single ventricle physiology with bidirectional Glenn while the two other patients had structurally normal heart (Table). The mapping using the OW & EML techniques confirmed the site of AP breakthrough conduction at Rt posteroseptal area in 3 of them and Rt posterolateral area in the remaining one, ablation resulted in immediate loss of preexcitation with no recurrence in all patients. Average fluro dose was 0.1 Gy which is significantly lower than the average dose in the remaining AVRT cases. Over median follow up period of 9 months, there were no recurrence of the accessory pathways & no complications. Conclusion Open window mapping technique is highly beneficial for accurate & fast mapping of accessory pathways especially in those with complex congenital heart where AP ablation remains considerably more challenging. OWM also added benefit in redo cases as the previous ablation trials hampered manual EGM interpretation. Finally, most of our cases were pediatrics where using high density mapping catheters and contact force ablation catheters appears to be safe and effective.Demographic, ECG, Echo & procedure data3D map & Echo in patient 2

Thermovision study of a residential building under climatic conditions of South Kazakhstan in a cold period

In this study, a nine-storey residential building was examined for thermal protection, located in Shymkent, Republic of Kazakhstan. Two two-room flats were considered with the possibility to inspect the exterior envelopes in four orientations. The examination was carried out at different times of the day according to three criteria: exterior envelope in the form of corner joints, translucent envelope in the form of window openings and the exterior façade of the building. The study found that the temperature at the surface of the room joints at lunchtime increased from 0.8% to 12% depending on the orientation of the exterior envelope. At the same time, it was found that in the morning and evening hours the temperature inside the living rooms is maintained at 25.8 - 26.5ºC due to excessive consumption of heat energy by increasing the heating power up to 15.6% relative to lunchtime, which leads to an excessive increase in air temperature by 7 - 18%. The value of humidity of living rooms also showed non-compliance with the optimal value by 3 - 15% relative to the current norms. As a result of the analysis of thermograms of translucent openings it was found that the surface temperature of the envelope at lunchtime increased by 9.9 - 23.2% in all cases of orientations, and the surface temperature of translucent openings of southern orientation is on average 18.2% higher relative to other orientations, which also indicates the influence of solar radiation on the thermal values of translucent openings. The analysis of thermograms and temperature of characteristic points of the external façade with regard to orientations showed a temperature difference from 7.5ºC to 21ºC depending on the orientation of the building, where the most exposed to solar radiation façade of southern orientation, which showed an increase in surface temperature by 3 times. Thus, the obtained results of the study will further contribute to the development of energy-efficient designs of external enclosures, considering the influence of all factors on the process of heat exchange, which is the main objective of the authors’ comprehensive study.

Conflict Resolution as A Game: The Government's Policy Agenda has Been Neglected Through Negotiation and Compensation

Purpose: This research examines how official actors play a role in resolving conflicts between the farming community and the cement company. Method: This qualitative research focuses on farmers in Puger District affected by PT Imasco Asiatic's irrigation canal closure, as well as community leaders. In-depth interviews will be conducted with participants, and data will be confirmed using GIS for accuracy. GIS is used to verify the accuracy of the information. Result and Discussion: Commodity factories in Indonesia have refused to implement the government's policy agenda and instead negotiated with the Water User Farmers Association (HIPPA) and provided compensation. Both official and unofficial parties, including community and religious leaders, tried to resolve the conflict, but HIPPA, without deliberation, agreed to accept compensation. The change in attitude of the Puger Kulon farming community made the government's struggle meaningful. The role of actors in the policy process is complex, with each actor competing to open policy windows and influence the agenda-setting stage. Implication of the Research: This research contributes to the existing literature by providing insights into conflict resolution between government companies and citizens. On the other hand, highlighting the role of actors in the policy process is complex, with each actor competing to open policy windows and influence the agenda-setting stage. Originality/Value: Official actors (government) dominate in policy making. However, the government has no coercive power since there is a non-official group (outside government) that has negotiated and changed the behavior of farmers.

Assessing impact of intermittent window opening strategies on pathogen-laden droplet dispersion in a coach bus

Assessing impact of intermittent window opening strategies on pathogen-laden droplet dispersion in a coach bus

Detrimental effects of scene manipulations on temperature-based time since death estimation

In forensic casework, time since death (TSD) estimations may play a crucial role to establish chains of events as well as for alibi assessment in homicide cases. Classical TSD estimation relies on reasonably stable ambient temperatures and a correct documentation of ambient and rectal temperatures. This constancy is in some cases disturbed by post-discovery alterations of the crime scene, e.g. opening a window. In order to develop a better understanding of this alteration-based detrimental impact on TSD estimation as well as to identify feasible recommendations for casework, the present pilot study examined ambient temperature effects of different window opening scenarios regarding various time intervals (5 to 360 min) in a furnished 10 m2 apartment during winter. In this context, in addition to the ambient temperature and thus the cooling rate of the room, re-approximation to initial room temperature, potential influences on a nomogram-based time since death estimation using a fictitious case, and the impact of the measurement height above the ground were investigated. Our data indicate a significant reduction of the mean temperature decrease rate after 15 min regardless of the remaining opening time and a correlation with the size of the respective opening surfaces. Re-approximation to initial room temperatures was observed with up to three times longer than the initial opening time. There was no evidence of a substantial advantage of temperature measurements above the level of the corpse (> 0.1 m). The limitations of the study and its applicability for forensic casework are critically reviewed.

A Clinical Approach for the Removal of a Large Antral Pseudocyst with Simultaneous Maxillary Sinus Augmentation: A Case Series.

For a large benign lesion within the maxillary sinus, such as an antral pseudocyst, maxillary sinus floor augmentation is more commonly performed using a two-stage approach. This involves first removing the lesion, and then, re-entry following several months of healing. In this case series, we described the "one-bony-window" approach, which is a technical surgical modification of the previous one-stage approach, for simultaneous cyst removal and maxillary sinus floor augmentation. Four patients with large maxillary antral pseudocysts were included. The "one-bony-window" approach involves the preparation of a large window opening of approximately 15 mm × 20 mm at the lateral wall. A mesiodistally extended intentional perforation was made in the upper part of the exposed membrane to enhance the access for instrumentation. The antral pseudocyst was removed in its entirety without being deformed to prevent rupture or leakage of the cystic contents. Subsequent detachment and elevation of the Schneiderian membrane at the sinus floor significantly reduced the perforation site, and bone grafting with implant placement was performed simultaneously. This alleviated the need to surgically repair the perforation. The lateral opening was either uncovered or repositioned using bony window lids. Healing abutments were connected after six months, and the final prosthesis was placed after two months. At the 1-year follow-up, the antral pseudocysts had resolved with no specific recurrence, and the stability of the augmented sinus was maintained with excellent implant survival. Within the limitations of our findings, the "one-bony-window" technique can be suggested for the simultaneous removal of large antral pseudocysts and maxillary sinus floor augmentation with favorable clinical outcomes.

Discrepancies of Functional Requirements of Façade Opening System between Real-Life Public and Built Environment Experts Focusing on Thermal Comfort and Ventilation

A survey was conducted to analyze the discrepancies of the functional requirements of the façade system in residential units among 605 of the real-life public and 73 experts. Personal and housing information, resident life patterns, public façade usage behavior, and functional requirements were collected from the respondents. Both the public and experts recognized insulation as the main function of façade opening systems. More than 85% of the public and experts opened windows for ventilation, but ventilation was ranked 3rd amongst the public and 4th amongst experts in the main functions list of façade systems. The public cited the inflow of fine dust as the main reason for dissatisfaction with opening windows. In contrast, the experts cited a decrease in thermal comfort due to the inflow of external moisture as the reason for dissatisfaction with opening windows. The results showed that discrepancies exist between the public and experts’ perceptions of the main function of housing façade systems. Analyzing the common points and differences between the public and experts’ perception can help in developing façade system design and control technology.

In situ air change rate estimation from metabolic CO2 measurement. Summer experimental campaign in a single-family test house

Night ventilation is one of the most promising approaches for reducing the cooling-energy consumption of buildings while improving the summer thermal comfort of occupants. More accurate measurement of the air change rate (ACR) through window openings may help promote this approach. Indeed this is still an active research topic that requires well-controlled experimental data. This article aims to expand the application scope of the tracer gas methodology for dynamic estimation of ACR in residential buildings. Controlled inputs, such as human metabolic CO2 emissions and various window-opening configurations, are chosen to represent the actual use of a single-family house during the cooling season. The measurement dataset – including weather on site, wind on the walls, indoor air speed, temperature, relative humidity, CO2 concentration at various positions and at a time resolution of 1 min – is processed for sharing. Wind fluctuation on the external wall emphasizes the dynamic nature of ACR. Indoor temperature and CO2 concentration measurements showed a mean spatial heterogeneity of 1.0 °C and 625 ppm, respectively. Indoor CO2 levels are low (<2000 ppm), which is a limitation in the use of the tracer gas equation. Thus, the potential of the dataset for dynamic ACR estimation is discussed by introducing and analyzing two indicators. Finally, the ability of the dataset to compute dynamic ACR is demonstrated through deterministic solving of the tracer gas equation.