Onda Cryl Research Articles

Evaluation of a glaze polishing technique for pigmented denture acrylic resin submitted to thermocycling and disinfection

Aims: Compare the mechanical and physical properties of two polishing techniques for acrylic resins under the influence of disinfection. Materials and Methods: Two hundred and eight circular samples (10 mm diameter × 3 mm height) were manufactured, with 160 for the color stability, hardness, surface roughness, and wettability (n = 10) analyses, and 48 for the scanning electron microscopy and atomic force microscopy evaluation (n = 1). Two brands of prosthesis acrylic resin, Onda Cryl and Lucitone, were used to manufacture the samples. Half of the samples were intrinsically pigmented with a purple acrylic pigment (Policor) at 7% of the total weight in powder; half of those received the mechanical polish with sand paper under constant water irrigation in a universal polishing machine at 300 rpm (control), and half received a uniform coat of a photopolymerized glaze (Megaseal) to be tested. The samples were kept immersed in distilled water for 24 h before the initial measurements (T0), afterward, they were divided into two disinfection procedures; half were disinfected through microwave energy and half through cleaning tablets (Efferdent) for 60 days (T1). Results: The glaze polished groups presented inferior chromatic stability and the pigments prevented discoloration for the glaze polish. The disinfectant solutions promoted a superficial degradation of the acrylic resin for both polishing techniques. Lucitone presented higher hardness values than Onda Cryl (P

The Effect of Disinfection Techniques on the Flexural Strength of Thermopolymerisable Acrylic Resins With or Without Pigment Addition.

The aim of this study was to assess the flexural strength of two brands of thermopolymerisable acrylic resins (Onda Cryl, Artigos Odontológicos Clássico Ltda, São Paulo, SP, Brazil; and Lucitone 550, Dentsply, York, PA, USA) with varying concentrations of pigment (Poli-Côr, Artigos Odontológicos Clássico Ltda, São Paulo, SP, Brazil) under the influence of thermocycling, storage and disinfection. A total of 210 samples were manufactured (105 for each acrylic resin brand), with dimensions of 64 x 10 x 3.3 mm. The samples were divided into 30 subgroups (n = 7) according to the proportion of pigment used (without pigment, 3% and 7%), the assessment period (initial or thermocycling for 2000 cycles) and disinfection method (immersion in 1% sodium hypochlorite, (Apothicário, Araçatuba, SP, Brazil), microwave energy or immersion in alkaline peroxide (Efferdent, Pfizer, Morris Plains, NJ, USA). The samples were submitted to the flexural strength test before and after thermocycling, and after storage with disinfection. The disinfection process was performed every 3 days, for 60 days. Data were submitted to analysis of variance (ANOVA) and Tukey test (p < 0.05). The factors that provided statistical alteration in flexural strength values were resin type and assessment period. The Onda Cryl resin and the period after disinfection (126 ± 25 MPa) exhibited the higher values of flexural strength. Following disinfection, Onda-Cryl resin exhibited the highest values of flexural strength. All the samples obtained are considered clinically acceptable.

Surface Hardness of Acrylic Resins Exposed to Toothbrushing, Chemical Disinfection and Thermocycling

The aim of this study is to investigate the effect of the toothbrushing, chemical disinfection and thermocycling treatments on the surface hardness of acrylic resins used for denture bases. The Classico (conventional), Onda Cryl (microwaved) and QC-20 (boiled) thermoactivated acrylic resins were used to prepare specimens. Prior to and after cleaning procedures, the specimens were submitted to a hardness test in an indenter (HMV-2000 Shimadzu), employing a load of 50 gf for 10 s. Three-way ANOVA and Tukey’s test (α=0.05) were used to analyze the data. Prior to thermocycling, statistical differences were found among treatments for Onda Cryl, with greater hardness values observed for Efferdent and hypochlorite; lower hardness value was obtained after toothbrushing, and intermediate value was found for the control. Differences were found among resins for the control treatment, with higher value for QC-20 resin, lower value for the Classico, and intermediate value for the Onda Cryl. Following thermocycling, differences were observed among treatments for Onda Cryl, with control specimens presenting higher values, lower value for toothbrushing and intermediate values for Efferdent and hypochlorite. Differences were also found for QC-20, with Efferdent and hypochlorite presenting higher values, lower value for control and intermediate value for toothbrushing. Differences were found among resins for the control treatment, with higher value for Onda Cryl resin, lower value for the QC-20, and intermediate value for the Classico. The QC-20 resin showed higher value for control prior to thermocycling and Onda Cryl after thermocycling. Different effects on the surface hardness of acrylic resins used for denture bases were observed when associating thermocycling with toothbrushing or chemical disinfections.

Effect of beverages and mouthwashes on the hardness of polymers used in intraoral prostheses.

The mechanical properties of acrylic resins used in intraoral prostheses may be altered by frequent exposure to liquids such as beverages and mouthwashes. This study aimed to evaluate the effect of thermocycling and liquid immersion on the hardness of four brands of acrylic resins commonly used in removable prostheses (Onda Cryl, QC-20, Clássico, Lucitone). For each brand of resin, seven specimens were immersed in each of six solutions (coffee, cola, red wine, Plax-Colgate, Listerine [LI], Oral B), and seven more were placed in artificial saliva (control). The hardness was tested using a microhardness tester before and after 5000 thermocycles and after 1, 3, 24, 48, and 96 hours of immersion. The results were analyzed using three-way repeated-measures ANOVA and Tukey's test (p < 0.05). The hardness of the resins decreased following thermocycling and immersion in the solutions. Specimens immersed in cola and wine exhibited significant decreases in hardness after immersion for 96 hours, although the greatest significant decrease in hardness occurred in specimens immersed in LI. However, according to American Dental Association specification 12, the Knoop hardness of acrylic resins for intraoral prostheses should not be below 15. Thus, the median values of superficial hardness observed in most of the acrylic resins in this study are considered clinically acceptable. The microhardness of polymers used for intraoral prostheses decreases following thermocycling. Among specimens immersed in beverages, those immersed in cola or wine experienced the greatest decrease in microhardness. Immersion of acrylic resins in LI significantly decreased the microhardness in relation to the initial value. Among the resins assessed, QC-20 exhibited the lowest initial hardness.

Effect of intrinsic nanoparticle pigmentation on the color stability of denture base acrylic resins

Intrinsic pigmentation is widely used to improve the esthetic features of denture base acrylic resins. However, acrylic resin may discolor over time. The purpose of this study was to investigate the effect of intrinsic nanoparticle pigmentation on the color stability of acrylic resins. The acrylic resins, Onda Cryl, QC 20, Classico, and Lucitone, were evaluated. Twenty-one disk-shaped specimens (3 × 30 mm) were fabricated from each acrylic resin. Seven were colored with 3% Poli-Cor intrinsic pigment used to color denture base, 7 were colored with 7% pigment, and 7 were not pigmented. In addition, 7 specimens were fabricated containing only pigment. The specimens were thermally cycled 2000 times between 5°C and 55°C with a 30-second dwell time at each temperature. The specimen colors were measured with a spectrophotometer and evaluated with the CIE L*a*b* system before (B) and after thermal cycling (T). The pigment morphology was analyzed by using a scanning electron microscope (SEM) and energy-dispersive x-ray spectroscopy (EDS) techniques. The results were analyzed with 2-way nested ANOVA and Tukey HSD tests (α=.05). Classico acrylic resin with and without pigment underwent the least color change, followed in order by Lucitone, Onda Cryl, and QC-20. The presence of pigments reduced the color change of the acrylic resins significantly (P<.05) for the specimens containing 7% pigment (0.32 ±0.18 ΔE). Titanium was the sole metallic component present in the pigment, probably in the oxide form (TiO2). Nanoparticle pigments enhanced the color stability of denture base acrylic resins.

Effect of thermal cycling and disinfection on microhardness of acrylic resin denture base

The purpose of this study was to investigate the effect of thermal cycling and disinfection on the microhardness of acrylic resins denture base. Four different brands of acrylic resins were evaluated: Onda Cryl, QC 20, Classico and Lucitone. Each brand of acrylic resin was divided into four groups (n = 7) according to the disinfection method (microwave, Efferdent, 4% chlorhexidine and 1% hypochlorite). Samples were disinfected during 60 days. Before and after disinfection, samples were thermal cycled between 5–55 °C with 30-s dwell times for 1000 cycles. The microhardness was measured using a microhardener, at baseline (B), after first thermal cycling (T1), after disinfection (D) and after second thermal cycling (T2). The microhardness values of all groups reduced over time. QC-20 acrylic resin exhibited the lowest microhardness values. At B and T1 periods, the acrylic resins exhibited statistically greater microhardness values when compared to D and T2 periods. It can be concluded that the microhardness values of the acrylic resins denture base were affected by the thermal cycling and disinfection procedures. However, all microhardness values obtained herein are within acceptable clinical limits for the acrylic resins.

Effect of thermal cycling and disinfection on colour stability of denture base acrylic resin

The purpose of this study was to investigate the effect of thermal cycling and disinfection on the colour change of denture base acrylic resin. Four different brands of acrylic resins were evaluated (Onda Cryl, QC 20, Classico and Lucitone). All brands were divided into four groups (n = 7) determined according to the disinfection procedure (microwave, Efferdent, 4% chlorhexidine or 1% hypochlorite). The treatments were conducted three times a week for 60 days. All specimens were thermal cycled between 5 and 55°C with 30-s dwell times for 1000 cycles before and after disinfection. The specimens' colour was measured with a spectrophotometer using the CIE L*a*b* system. The evaluations were conducted at baseline (B), after first thermal cycling (T1 ), after disinfection (D) and after second thermal cycling (T2 ). Colour differences (ΔE) were calculated between T1 and B (T1 B), D and B (DB), and T2 and B (T2 B) time-points. The samples submitted to disinfection by microwave and Efferdent exhibited the highest values of colour change. There were significant differences on colour change between the time-points, except for the Lucitone acrylic resin. The thermal cycling and disinfection procedures significantly affected the colour stability of the samples. However, all values obtained for the acrylic resins are within acceptable clinical parameters.

Effect of aluminium oxide particle sandblasting on the artificial tooth-resin bond.

The influence of tooth ridge-lap surface sandblasting with aluminium oxide particles was evaluated on the adhesion of artificial teeth to acrylic resins. Specimens were made with the acrylic resin adhered to teeth (BioCler GII), according to an unmodified surface, glossy surface sandblasted with 50-μm particles and conventional (Classico) or microwaved (Onda Cryl) resin, and a glossy surface sandblasted with 100-μm particles and Classico or Onda Cryl resin. The shear bond test was performed in an Instron machine using a 500-N load cell and cross-speed of 1 mm/min. The analysis of variance revealed significant difference in the tooth-resin shear bond strength for resin, surface treatment, and interaction. For conventional resin, control, 50-, and 100-μm particles showed statistically-different values; for microwaved resin, the control showed less statistical difference when compared to 50- and 100-μm particle treatments; for between resins, only the 100-μm particle treatment showed statistically-different values, with lower values for the microwaved resin. Mixed failures (cohesive in the resin and adhesive) were predominantly observed in all groups. Mixed (cohesive in the tooth and adhesive) or adhesive failures were not observed. Sandblasting with different aluminium oxide particle sizes produced different effects on the shear strength values of the tooth-resin bond.

Fractographic analysis, accuracy of fit and impact strength of acrylic resin

This study evaluated accuracy of fit, impact strength, types and morphology of fractures of a microwave acrylic resin polymerized with a cycle alternative to that recommended by the manufacturer. Onda Cryl was polymerized according to the manufacturer's instructions (MC), 3 min at 360 W, 4-min pause, and 3 min at 810 W; and with an alternative cycle (AC) of 6 min at 630 W. Accuracy of fit was measured at 3 points at the right (A) and left (B) ridge crests and at the midline (C) on the posterior palatal seal for each denture base (n = 10/group). The measurements were taken immediately after finishing and after 30-day storage in water. The impact strength test (Charpy method) was performed with a 40 kJ/cm load (n = 20/group). Fractographic analysis was accomplished for all fragments and the fracture types were characterized by means of their morphology, crack propagation angles and microstructure. Accuracy of fit data were analyzed by ANOVA, impact strength and radius values were compared by the t test, and the fractographic analysis data, by the Wilcoxon Mann-Whitney test. The significance level was fixed at p < 0.05. No statistical differences were found between the two cycles of polymerization used. However, after the 30-day storage period in water, the denture bases showed better fit (P < .05). Most of the fractures were classified as brittle (MD: 70%, AC: 80%). Based on the results of this study, it could be concluded that both polymerization cycles are adequate to polymerize the denture resin studied.

Effect of chemical denture cleansers on flexural resistance and color changes of microwave-polymerized acrylic resins

Aim: The aim of this study was to assess the flexural resistance and color alterations of microwave-polymerized acrylic resins immersed in denture cleansers for different periods of time. Methods: Forty-five rectangular specimens (65x10x3mm) of each commercial brand of the microwave-activated acrylic resins (Vipi Wave and Onda Cryl) were divided in three denture cleanser groups (Bony Plus, Corega Tabs and Efferdent Plus) and a control group (immersion in water). Soaking trials of 15 min and 8 h simulated 30 days of use. The flexural strength test was carried out in a universal testing machine. Color alterations were assessed by visual inspection of photographs. The results obtained in the flexural test, in kgf, were converted to MPa and these values were submitted to analysis of variance with a 5% significance level. Results: There were no significant differences (p<0.05) between Onda Cryl (85.61±12.76) and Vipi Wave (89.8±19.95) after the soaking trials regarding the use of different denture cleansers. No differences were found in relation to the solutions [Bony Plus (88.52±9.89), Corega Tabs (88.75±12.71) and Efferdent (85.86±12.11)], soaking periods [control (87.17±12.92), 15 min (88.05±11.74) and 8 h (87.91±10.30)], and interactions during the 30 days of simulated use. Visual inspection did not detect any color alterations. Conclusions: Denture cleansers, when used according to the manufacturers’ instructions, did not cause any mechanical or visual alterations in the microwave-polymerized acrylic resins after a simulated period of 30 days of use.

Effects of nystatin, fluconazole and propolis on poly(methyl methacrylate) resin surface

The prevalence of candidosis in denture wearers is as well established as its treatment with antifungal agents (AAs). However, little research has been done regarding the effects of AAs on denture base surfaces. Therefore, the aim of this study was to evaluate the effects of fluconazole (FLU), nystatin (NYS) and propolis orabase gel (PRO) on poly (methyl-methacrylate) (PMMA) surfaces. Deionized water and orabase gel without any active component were used as control groups. Conventional heat-polymerized (Clássico) and microwave-polymerized (Onda Cryl) acrylic resins were used. After polymerization, the specimens were polished and had their surfaces evaluated for roughness, free energy and Knoop hardness. Subsequently, specimens were immersed in AAs and controls for 14 days at 35+/-2 degrees C and all variables were measured again. Data were analyzed statistically by 2-way ANOVA followed by Tukey's test (alpha=0.05). Roughness results showed similar behavior for both PMMA resins, with PRO reaching the highest values and differing significantly from the other AAs (p<0.05). No statistically significant differences (p>0.05) were found between the two PMMA resins or between NYS and FLU as regards surface free energy. In conclusion, PRO was able to induce changes in PMMA surface properties, such as roughness, which could be related to microbial adhesion.

Influence of storage period and effect of different brands of acrylic resin on the dimensional accuracy of the maxillary denture base

The aim of this study was to evaluate the dimensional changes of denture bases made from different resins after different storage periods. For this purpose, 25 sets of plaster models/resin bases were prepared using 4 acrylic resins submitted to two types of polymerization: 1--QC-20 submitted to polymerization by microwave energy; 2--QC-20 submitted to polymerization by water hot bath; 3--Vipi Cril submitted to polymerization by water hot bath; 4--Vipi Wave submitted to polymerization by microwave energy; and 5--Onda Cryl submitted to polymerization by microwave energy. After polymerization, the specimens were sectioned for accuracy readings using a comparison microscope. Readings were taken at 3 points: the crests of the right (A) and left (B) ridges, and the median region of the palate, in 4 different periods. The data obtained were submitted to two-way ANOVA and Tukey's test at 5% significance level. The greatest distortions were found in the posterior palatal region of the base (M), with statistically significant difference (p<0.05) for the studied resins. All acrylic resins presented dimensional changes and the storage period influenced these alterations.

Impact strength and fracture morphology of denture acrylic resins

Microwave-polymerization cycles may affect the impact strength and fracture morphology of denture base acrylic resin, and the microstructural effects of these processes have not been fully determined. This study evaluated the impact strength and fracture morphology of denture base acrylic resins processed by microwave energy and hot water bath. Twenty specimens measuring 65 x 10 x 2.5 mm were fabricated from each of 4 acrylic resins processed according to the manufacturers' recommendations: Lucitone 550 (control; 9 hours at 74 degrees C); Onda Cryl (3 minutes at 360 W + 4 minutes pause + 3 minutes at 810 W); Acron MC (3 minutes at 500 W); and Vipi Wave (20 minutes at 180 W + 5 minutes at 540 W). The impact strength was evaluated in an impact testing machine using the Charpy method with a load (impact action) of 3.95 J. Mean values of impact strength were compared by Tukey honestly significant difference test (alpha = .05). Fractures were classified as brittle or intermediate. Fractographic analysis was performed for all fragments by angle analyses of crack propagation, and the microstructural morphology characterization was accomplished with scanning electron microscopy (SEM). Data from the fractography analysis were submitted to the Kruskal-Wallis test for angles and radius (alpha = .05). Significant differences (P < .001) were found in the impact strength for Vipi Wave and Acron MC acrylic resins, which demonstrated the lowest values (0.19 +/- 0.04 and 0.21 +/- 0.02, respectively). Most fractures were classified as brittle (Lucitone 55%; Onda Cryl 75%; Acron MC 90%; Vipi Wave 65%). Fractographic angle analysis of brittle fractures showed no differences among acrylic resins studied; however, angle values of intermediate fractures for Onda Cryl were lower in comparison with those from Lucitone 550 and Vipi Wave (P = .03). The SEM observations revealed that brittle fractures showed defined and organized crystallographic planes, whereas the intermediate fractures had a disorganized appearance. Within the limitations of this study, it was observed that impact strength in microwave-polymerized acrylic resins varies according to the period of irradiation. Acrylic resins exhibited a high number of brittle fractures, irrespective of the processing technique.

Influence of a cobalt-chromium metal framework on surface roughness and Knoop hardness of visible light-polymerized acrylic resins

Although visible light-polymerized acrylic resins have been used in removable partial dentures, it is not clear whether the presence of a metal framework could interfere with their polymerization, by possibly reflecting the light and affecting important properties, such as roughness and hardness, which would consequently increase biofilm accumulation. The aim of this study was to compare the roughness and Knoop hardness of a visible light-polymerized acrylic resin and to compare these values to those of water-bath- and microwave-polymerized resins, in the presence of a metal framework. Thirty-six specimens measuring 30.0 × 4.0 ± 0.5 mm of a microwave- (Onda Cryl), a visible light- (Triad) and a water-bath- polymerized (Clássico) (control) acrylic resins containing a cobalt-chromium metal bar were prepared. After processing, specimens were ground with 360 to 1000-grit abrasive papers in a polishing machine, followed by polishing with cloths and 1μm diamond particle suspension. Roughness was evaluated using a profilometer (Surfcorder SE 1700) and Knoop hardness (Kg/mm2) was assayed using a microhardness tester (Shimadzu HMV 2000) at distances of 50, 100, 200, 400 and 800 μm from the metal bar. Roughness and Knoop hardness means were submitted to two-way ANOVA and compared by Tukey and Kruskal Wallis tests at a 5% significance level Statistically significant differences were found (p<0.05) for roughness and Knoop hardness, with light-polymerized resin presenting the highest values (Ra = 0.11 μm and hardness between 20.2 and 21.4 Kg/mm2). Knoop values at different distances from the metal bar did not differ statistically (p>0.05). Within the limitations of this in vitro study, it was concluded that the presence of metal did not influence roughness and hardness values of any of the tested acrylic resins.

Influence of chemical and mechanical polishing on water sorption and solubility of denture base acrylic resins

Influence of polishing methods on water sorption and solubility of denture base acrylic resins was studied. Eighty samples were divided into groups: Classico (CL), and QC 20 (QC) - hot water bath cured; Acron MC (AC), and Onda Cryl (ON) - microwave cured; and submitted to mechanical polishing (MP) - pumice slurry, chalk powder, soft brush and felt cone in a bench vise; or chemical polishing (CP) - heated monomer fluid in a chemical polisher. The first desiccation process was followed by storage in distilled water at 37 +/- 1 degrees C for 1 h, 1 day, 1, 2, 3 and 4 weeks. Concluding each period, water sorption was measured. After the fourth week, a second desiccation process was done to calculate solubility. Data were submitted to analysis of variance, followed by Tukey test (p<or=0.05). Means of water sorption (%) and solubility (%), respectively, were: CL-MP: 1.92 and 0.02; CL-CP: 1.98 and 0.52; QC-MP: 2.31 and -0.05; QC-CP: 2.32 and 0.25; AC-MP: 2.45 and -0.07; AC-CP: 2.43 and 0.41; ON-MP: 2.32 and -0.06; ON-CP: 2.34 and 0.27. Mechanical polishing promoted significantly lower solubility of acrylic resins; initially, water sorption values were higher for chemically polished samples, however, after 4 weeks all groups were similar.

Surface roughness of acrylic resins submitted to mechanical and chemical polishing

Surface roughness is extremely important as it influences micro-organism accumulation and consequently oral health. The aim of the present study was to evaluate the influence of mechanical polishing (MP) and chemical polishing (CP) on surface roughness of four heat-cured denture base acrylic resins. Twenty sample discs were prepared for each of the following acrylic resins: Classico (CL), QC 20 (QC), Acron MC (AC) and Onda Cryl (ON). The first two are boiling cured resins and the latter two are microwave cured. After curing and deflasking, samples were ground and subdivided into two groups: MP, which received pumice slurry, chalk powder, soft brush and felt cone, at a bench vice; and CP, which received fluid specifically for chemical polisher. Surface roughness was measured using a Surf Corder SE 1700 rugosimeter. Data collected were statistically analysed by analysis of variance followed by Tukey's test. Surface roughness means in mum were: CL-MP: 0.0350; CL-CP: 0.2298; QC-MP: 0.0307; QC-CP: 0.1792; AC-MP: 0.0312; AC-CP: 0.2700; ON-MP: 0.0321; ON-CP: 0.2949. It can be concluded that MP produced significantly smoother surfaces than CP and that surface roughness because of MP was not influenced by acrylic resin type, whereas this was not true of CP.

Effect of cooling procedure on final denture base adaptation.

Well-fitted dentures prevent hyperplasic lesions, provide chewing efficiency and promote patient's comfort. Several factors may affect final adaptation of dentures, as the type of the acrylic resin, the flask cooling procedure and the water uptake. This investigation evaluated the effect of water storage and two different cooling procedures [bench cooling (BC) for 2 h; running water (RW) at 20 degrees C for 45 min] on the final adaptation of denture bases. A heat-cured acrylic resin (CL, Clássico, Clássico Artigos Odontológicos) and two microwave-cured acrylic resins [Acron MC, (AC) GC Dent. Ind. Corp.; Onda Cryl (OC), Clássico Artigos Odontológicos] were used to make the bases. Adaptation was assessed by measuring the weight of an intervening layer of silicone impression material between the base and the master die. Data was submitted to ANOVA and Tukey's test (0.05). The following means were found: (BC) CL=0.72 +/- 0.03 a; AC=0.70 +/- 0.03 b; OC=0.76 +/- 0.04 c//(RW) CL= 1.00 +/- 0.11 a; AC=1.00 +/- 0.12 a; OC=0.95 +/- 0.10 a. Different labels join groups that are not statistically different (P > 0.05). Comparisons are made among groups submitted to the same cooling procedure (BC or RW). The conclusions are: interaction of type of material and cooling procedure had a statistically significant effect on the final adaptation of the denture bases (P < 0.05); water storage was not detected as a source of variance (P > 0.05) on the final adaptation.

Microwave-cured acrylic resins and silicone-gypsum moulding technique.

This study evaluated the residual monomer (RM), Knoop hardness (KHN) and transverse strength (TS) of two microwave-cured acrylic resins (Acron MC(R) (A), GC Dent. Ind. Corp., Tokyo, Japan and Onda Cryl (O), AO Classico Ltda, São Paulo, Brazil) when processed with an all-type III gypsum moulding technique (G) or a silicone-gypsum moulding technique (S). One hundred and forty four specimens were fabricated and equally distributed into four groups (AG, AS, OG and OS). The TS tests were conducted after 48 h of water storage, and KHN values were obtained after 24, 48, 72 h and 30 days. The RM was determined every 24 or 48 h over a period of 288 h. The acrylic resins were prepared and processed according to the manufacturer's directions. Both AS and OS showed the highest means (P < 0.05) for RM (microg cm-2) only after 24 h (AS = 56.84 +/- 27.39/AG = 7.51 +/- 5.75/OS = 3.59 +/- 1.60/OG = 1.02 +/- 0.3), 48 h (AS = 28.99 +/- 9.35/AG = 2.65 +/- 2.17/OS = 2.37 +/- 0.84/OG = 0.68 +/- 0.49) and 72 h (AS = 15.98 +/- 9.01/AG = 1.40 +/- 0.57/OS = 1.87 +/- 0.52/OG = 0.75 +/- 0.44). Both AS and OS showed the highest means (P < 0.02) for KH after 24 h (AS = 18.69 +/- 2.3/AG = 17.79 +/- 0.7/OS = 18.41 +/- 1.0/OG = 16.04 +/- 0.6). After 48 h the mean values for OS and OG differed significantly (P < 0.03) (OS = 18.67 +/- 0.8/OG = 16.75 +/- 0.8). No differences of KHN were found among the groups during the storage periods. The TS values for A and O were not affected by either G or S (P > 0.05). Silicone-gypsum mould technique affected the RM and KHN of the resins in the first 2 and 5 days of analysis, respectively. The type of mould did not affect TS, and the acrylic resins differed from each other for all properties regardless of the type of mould.