On-line Solid-phase Extraction Research Articles

Biochar from Grapevine Pruning Residues as an Efficient Adsorbent of Polyphenolic Compounds.

Agricultural waste, which is produced in large quantities annually, can be a threat to the environment. Biochar (BC) production represents a potential solution for reducing the amount of grapevine pruning residues and, accordingly, the impact on the environment and climate change. Biochar produced by the process of pyrolysis from grapevine pruning residues was investigated and characterized to be applied as an adsorbent of polyphenolic compounds with the aim of using the waste from viticultural production to obtain a quality product with adsorption and recovery potential. Standards of caffeic acid (CA), gallic acid (GA), and oleuropein (OLP) were used as polyphenolic representatives. The obtained data were fitted with the Langmuir and Freundlich isotherms models to describe the adsorption process. The best KL (0.39) and R2 (0.9934) were found for OLP using the Langmuir model. Furthermore, the adsorption dynamics and recovery potential of BC were investigated using an adapted BC column and performed on an HPLC instrument. The adsorption dynamics of biochar resulted in the adsorption of 5.73 mg CA g-1 of BC, 3.90 mg GA g-1 of BC, and 3.17 mg OLP g-1 of BC in a 24 h contact. The online solid phase extraction of the compounds performed on an HPLC instrument yielded a recovery of 41.5 ± 1.71% for CA, 61.8 ± 1.16% for GA, and 91.4 ± 2.10% for OLP. The investigated biochar has shown a higher affinity for low-polar compound adsorption and, consequently, a higher polar compound recovery suggesting its potential as an efficient polyphenolic compound adsorbent.

Biohybrid adsorbent for the preconcentration of lead and its determination in fruit juices by electrothermal atomic absorption spectrometry.

Fruit juices are one of the most non-alcoholic beverages consumed in the world. Essential elements and other nutrients present in fruit juices play an important role in human well-being. However, fruit juices may also contain potentially toxic elements at trace levels, causing health risks. The objective of this work was to develop an analytical methodology based on the preconcentration of lead using a new biodegradable hybrid material composed of Rhodococcus erythropolis AW3 bacteria and Brassica napus hairy roots. The biodegradable hybrid material was implemented in an online solid phase extraction system for the determination of lead in fruit juices by electrothermal atomic absorption spectrometry. Effects of critical parameters on lead retention were studied. Under optimal experimental conditions, extraction efficiency higher than 99.9% and an enrichment factor of 62.5 were achieved. The dynamic capacity of the biodegradable hybrid material was 36 mg/g, which favored the reuse of the column to at least 8 biosorption-desorption cycles. The limit of detection and quantification for preconcentration of 5 mL of sample were 5.0 and 16.5 ng/L lead, respectively. The relative standard deviation was 4.8% (at 1 µg/L lead and n = 10). The developed method was suitable to be applied for lead determination in different types of fruit juices.

On-line determination of the trace amount of cobalt(II) in real samples by flame atomic absorption spectrometry method after pre-concentration by modified polyvinyl chloride

This work reports a simple and sensitive on-line solid-phase extraction system for the pre-concentration and determination of a trace amount of Co(II (ions by flame atomic absorption spectrometry (FAAS). This method is based on the on-line retention of cobalt ions with polyvinyl chloride modified by 3-(2-thiazolylazo)-2,6-diaminopyridine in a mini-column system. The retained Co(II) ions were eluted with 1.0 mol L−1 HCl, and direct aspiration to flame atomic absorption spectrometry (FAAS) for an accurate determination of it. The important experimental parameters such as the solution pH, length of column (adsorbent mass), sample flow rate, solvent eluent, type and concentration of the eluent, and co-existing ion effects were investigated in detail and optimized. Under the optimum conditions, the calibration graph was linear over the concentration range of 2–150 µg L−1 for pre-concentration of 10.0 mL of the sample solution. The interassay precession (n = 6) was in the range of 1.8–5.2% at the concentration levels of 10.0, 50.0, 100.0, and 140.0 µg L−1. The limit of detection and enhancement factor were 1.3 µg L−1 and 40, respectively. The method was applied for determination of trace levels of Co(II) ions in different real samples such as tap water, waste water, vegetable, fruit, and drug with satisfactory results.

Innovative thermally assisted on-line solid phase extraction-reversed phase liquid chromatography applied to targeted nutrimetabolomics in human biofluids

In this study, the use of thermal desorption in on-line solid phase extraction coupled with reversed phase liquid chromatography (on-line SPE-LC) was for the first time proposed and demonstrated for the desorption of analytes strongly retained by multiple interaction polymeric sorbents. In detail, this analytical strategy was applied to the on-line SPE-LC targeted analysis of a model set of 34 human gut metabolites characterized by heterogeneous physicochemical properties (i.e., octanol–water partition coefficient in the range −0.3 – 3.4). The novel thermally assisted on-line SPE approach was investigated in comparison to conventional room temperature desorption strategies based on the use of (i) an optimized elution gradient or (ii) organic desorption followed by post-cartridge dilution. The thermally assisted desorption strategy has been shown to be better performing and suitable for the development of a reliable and sensitive method for the analysis of the model group of analytes in urine and serum. In more detail, under the optimized experimental conditions, the proposed method provided negligible matrix effects in both biofluids for almost all target analytes. Moreover, method quantification limits were in the ranges 0.026–7.2 μg L−1 and 0.033–23 μg L−1 for urine and serum, respectively, i.e., comparable to or lower than those reported in methods previously published.

Self-Collection Blood Test for PFASs: Comparing Volumetric Microsamplers with a Traditional Serum Approach.

A remote sampling approach was developed at Eurofins for quantifying per- and polyfluoroalkyl substances (PFASs) in whole blood samples collected using volumetric absorptive microsamplers (VAMSs), which allow for self-collection of blood using a finger prick. This study compares PFAS exposure measured by self-collection of blood using VAMSs to the standard venous serum approach. Blood samples were collected from participants (n = 53) in a community with prior PFAS drinking water contamination using a venous blood draw as well as participant self-collection using VAMSs. Whole blood from the venous tubes was also loaded onto VAMSs to compare differences in capillary vs venous whole blood PFAS levels. Samples were quantified for PFASs using liquid chromatography tandem mass spectrometry and online solid-phase extraction. PFAS levels in serum were highly correlated with measurements in capillary VAMSs (r ≥ 0.91 and p < 0.05). Serum PFAS levels were generally twofold higher than whole blood, reflecting expected differences in their composition. Of interest, FOSA was detected in whole blood (both venous and capillary VAMSs) but not in serum. Overall, these findings indicate that VAMSs are useful self-collection tools for assessing elevated human exposure to PFASs.

Development, validation, and use of a monitoring method for fipronil and its metabolites in chicken eggs by QuEChERS with online-SPE-LC-Q/Orbitrap analysis.

The residues of fipronil and its metabolites in chicken eggs pose a threat to human health, so regular monitoring is necessary. However, the pretreatments of the existing detection methods are complex and time-consuming. A simple and streamlined pretreatment method is needed to improve the detection efficiency. A rapid, efficient, and facile approach employing QuEChERS with online solid-phase extraction liquid chromatography tandem Q-Exactive Orbitrap high resolution mass spectrometry (online-SPE-LC-HRMS) was established and evaluated for the determination of fipronil, fipronil-desulfinyl, fipronil-sulfone and fipronil-sulfide in chicken eggs. An improved sample preparation technique combining QuEChERS and online-SPE was developed. Negative targeted ion fragmentation scanning (t-MS2 ) and targeted-selected ion monitoring (t-SIM) of the HRMS were adopted to identify and quantify the target analytes. The proposed pretreatment method took a few steps in < 13 min to achieve excellent recoveries and negligible interference. High selectivity was acquired with the adoption of Q/Orbitrap HRMS. The LOQ of the analytes was 2.5 μg kg-1 , meeting the detection requirements of the MRL enacted by the Codex Alimentarius Commission (CAC), Japan and USA for the sum of fipronil and its metabolites. Extraction recoveries at three spiked concentration levels were within 84.56-93.84% with RSD ≤ 5.87%. The established method is efficient and easy to operate and displays satisfactory LOQs, recoveries, accuracy and precision. This approach serves as a reference method for monitoring eggs while providing potential solutions for fipronil determination in more complicated matrices.

Accurate determination of the milk protein allergen β-lactoglobulin by on-line aptamer affinity solid-phase extraction capillary electrophoresis-mass spectrometry

An on-line aptamer affinity solid-phase extraction capillary electrophoresis-mass spectrometry (AA-SPE-CE-MS) method was developed to purify, preconcentrate, separate, and characterize the milk allergenic protein β-lactoglobulin (β-LG) in food samples. The sorbent to pack into the SPE microcartidges was prepared by immobilizing an aptamer against β-LG onto magnetic bead particles. After optimizing the SPE-CE-MS method, the sample (ca. 75 μL) was loaded in separation background electrolyte (BGE, 2 M acetic acid pH 2.2), while a solution of 100 mM NH4OH (pH 11.2) (ca. 100 nL) was used for the protein elution. The linearity of the method ranged between 0.1 and 20 μg mL−1 and the limit of detection (LOD) was 0.05 μg mL−1, which was 200 times lower than by CE-MS. The method was repeatable in terms of relative standard deviation (RSD) for migration times and peak areas (<0.5% and 2.4%, respectively) and microcartridge lifetime was more than 25 analyses. The applicability of the method for the determination of low levels of β-LG was shown by analyzing milk-free foods (i.e. a 100% cocoa dark chocolate, a hypoallergenic formula for infants, and a dairy-free white bread) and milk-containing white breads. Results were satisfactory in all cases, thus demonstrating the great potential of the developed method for accurate food safety and quality control.

Determination of a lectin protein allergen in food by on-line aptamer affinity solid-phase extraction capillary electrophoresis-mass spectrometry

An aptamer affinity sorbent was prepared for clean-up, preconcentration, separation and characterization of a food allergen protein by on-line aptamer affinity solid-phase extraction capillary electrophoresis-mass spectrometry (AA-SPE-CE-MS). SPE microcartridges were packed with a sorbent based on magnetic bead particles modified with an aptamer against the target lectin protein concanavalin A (Con A). After optimization of several parameters of the SPE-CE-MS method, the sample (ca. 30 µL) was loaded in separation background electrolyte (BGE, 2 M acetic acid pH 2.2), while the retained protein was eluted with 100 mM NH4OH (pH 11.2) (ca. 100 nL). The developed method was linear between 0.5 and 20 mg·L-1 and the limit of detection (LOD) was 0.25 mg·L-1, which was 100 times lower than by CE-MS. The repeatability of the method was satisfactory, with relative standard deviations (RSD) for migration times and peak areas below 1.9 and 8.1%, respectively. In addition, the microcartridges could be reused more than 25 analyses without significant loss of extraction efficiency. Finally, the applicability and versatility of the developed method were demonstrated by analyzing low levels of Con A in different food matrices (i.e. white beans, as well as chickpea, lentils, and wheat flours), leading to satisfactory results, with recoveries between 87 and 115%.

On-line aptamer affinity solid-phase extraction direct mass spectrometry for the rapid analysis of α-synuclein in blood

On-line aptamer affinity solid-phase extraction direct mass spectrometry (AA-SPE-MS) is presented for the rapid purification, preconcentration, and characterization of α-synuclein (α-syn), which is a protein biomarker related to Parkinson's disease. Valve-free AA-SPE-MS is easily implemented using the typical SPE microcartridges and instrumental set-up necessary for on-line aptamer affinity solid-phase extraction capillary electrophoresis-mass spectrometry (AA-SPE-CE-MS). The essential requirement is substituting the application of the separation voltage by a pressure of 100 mbar for mobilization of the eluted protein through the capillary towards the mass spectrometer. Under optimized conditions with recombinant α-syn, repeatability is good in terms of migration time and peak area (percent relative standard deviation (%RSD) values (n = 3) are 1.3 and 6.6% at 1 μg mL−1, respectively). The method is satisfactorily linear between 0.025 and 5 μg mL−1 (R2 > 0.986), and limit of detection (LOD) is 0.02 μg mL−1 (i.e. 1000, 500, and 10 times lower than by CE-MS, direct MS, and AA-SPE-CE-MS, respectively). The established AA-SPE-MS method is further compared with AA-SPE-CE-MS, including for the analysis of α-syn in blood. The comparison discloses the advantages and disadvantages of AA-SPE-MS for the rapid and sensitive targeted analysis of protein biomarkers in biological fluids.

Simultaneous determination of fourteen pharmaceuticals in sewage sludge using online solid-phase extraction-liquid chromatography-tandem mass spectrometry combined with accelerated solvent extraction.

An online solid-phase extraction (SPE) liquid chromatography tandem mass spectrometry method (HPLC-MS/MS) combined with accelerated solvent extraction (ASE) was developed for simultaneous determination of 14 pharmaceuticals in sludge. In the online SPE procedures, ultrapure water with no additives was used as the loading solvent. In addition, low molecular weight targets such as atenolol were difficult to retain on SPE column after acetone was added to the washing solvent. The response signal of analytes can be greatly improved by adding 0.2% formic acid to the mobile phase. Under the optimized conditions, the recoveries of all the analytes ranged between 75.1 and 112%. Moreover, the limit of detections ranged from 1.8 to 7.9 ug/kg. The precision of analytical data was determined with relative standard deviation (RSD) ≤ 4.87%. This method was successfully applied to determine the concentration of pharmaceuticals in sludge.

Non-targeted analysis for the screening and semi-quantitative estimates of per-and polyfluoroalkyl substances in water samples from South Florida environments

Per- and polyfluoroalkyl substances (PFAS) are a group of anthropogenic pollutants that are found ubiquitously in surface and drinking water supplies. Due to their persistent nature, bioaccumulative potential, and significant adverse health effects associated with low concentrations, they pose a concern for human and environmental exposure. With the advances in high-resolution mass spectrometry (HRMS) methods, there has been an increasing number of non-targeted analysis (NTA) approaches that allow for a more comprehensive characterization of total PFAS present in environmental samples. In this study, we have developed and compared NTA workflows based on an online solid phase extraction- liquid chromatography high resolution mass spectrometry (online SPE-LC-HRMS) method followed by data processing using Compound Discoverer and FluoroMatch for the screening of PFAS in drinking waters from populated counties in South Florida, as well as in surface waters from Biscayne Bay, Key west, and Everglades canals. Tap water showed the highest number of PFAS features, indicating a poor removal of these chemicals by water treatment or perhaps the breakdown of PFAS precursors. The high number of PFAS features identified only by CD and FluoroMatch emphasizes the complementary aspects of these data processing methods. A Semi-quantitation method for NTA (qNTA) was proposed using a global calibration curve based on existing native standards and internal standards, in which concentration estimates were determined by a regression-based model and internal standard (IS) response factors. NTA play a crucial role in the identification and prioritization of non-traditionally monitored PFAS, needed for the understanding of the toxicological and environmental impact, which are largely underestimated due to the lack of such information for many PFAS.

Mass spectrometry quantitation of immunosuppressive drugs in clinical specimens using online solid-phase extraction and accurate-mass full scan-single ion monitoring

IntroductionTherapeutic drug monitoring (TDM) of immunosuppressants is essential for optimal care of transplant patients. Immunoassays and liquid chromatography-mass spectrometry (LC-MS) are the most commonly used methods for TDM. However, immunoassays can suffer from interference from heterophile antibodies and structurally similar drugs and metabolites. Additionally, nominal-mass LC-MS assays can be difficult to optimize and are limited in the number of detectable compounds. ObjectivesThe aim of this study was to implement a mass spectrometry-based test for immunosuppressant TDM using online solid-phase extraction (SPE) and accurate-mass full scan-single ion monitoring (FS-SIM) data acquisition mode. MethodsLC-MS analysis was performed on a TLX-2 multi-channel HPLC with a Q-Exactive Plus mass spectrometer. TurboFlow online SPE was used for sample clean up. The accurate-mass MS was set to positive electrospray ionization mode with FS-SIM for quantitation of tacrolimus, sirolimus, everolimus, and cyclosporine A. MS2 fragmentation pattern was used for compound confirmation. ResultsThe method was validated in terms of precision, analytical bias, limit of quantitation, linearity, carryover, sample stability, and interference. Quantitation of tacrolimus, sirolimus, everolimus, and cyclosporine A correlated well with results from an independent reference laboratory (r = 0.926–0.984). ConclusionsAccurate-mass FS-SIM can be successfully utilized for immunosuppressant TDM with good correlation with results generated by standard methods. TurboFlow online SPE allows for a simple “protein crash and shoot” sample preparation protocol. Compared to traditional MRM, analyte quantitation by FS-SIM facilitates a streamlined assay optimization process.

Innovated single flush on-line solid-phase extraction in bead injection format for flow programming-based determination of creatinine in human urine

Reaction-based assays are commonly automated and miniaturized via flow analysis. However, aggressive reagents can affect or destroy even the chemically resistant manifold during long-term use. Using on-line solid-phase extraction (SPE) can eliminate this drawback and allow for high reproducibility and further advanced automation, as presented in this work. Determination of creatinine in human urine, an important clinical marker, by sequential injection analysis was achieved using bead injection on-line SPE with specific UV spectrophotometric detection, providing the necessary sensitivity and selectivity of the method for bioanalysis. The automated SPE column packing and disposal, calibration, and fast measurement highlighted the improvements in our approach. Variable sample volumes and a single working standard solution eliminated matrix effects, broadened the calibration range, and accelerated the quantification.Our method comprised an injection of 20 μL of 100 × times diluted urine with aqueous acetic acid solution pH 2.4, sorption of creatinine in a strong cation exchanger SPE column, washing out urine matrix with 50% aqueous acetonitrile, and elution of creatinine with 1% ammonium hydroxide. The SPE step was accelerated by a single flush of the column when the eluent/matrix wash/sample/standard zones sequence was created in the pump holding coil, and then the sequence of the zones was flushed into the column at once. The whole process was continually spectrophotometrically detected at 235 nm, subtracted from the signal at 270 nm. A single run duration was less than 3.5 min. Method relative standard deviation was <5.0% (n = 6). A calibration range was linear within the range of 0.02–0.30 μg creatinine (R > 0.999), covering 1.0–15.0 mmol/L creatinine in urine. The standard addition method used two different volumes of a single working standard solution for quantification. Results proved the effectiveness of our improvements in the flow manifold, bead injection, and automated quantification. The accuracy of our method was comparable to the routine enzymatic assay of real urine samples in a clinical laboratory.

Does anti-inflammatory diet mitigate the deleterious effect of bisphenol A on mortality in US adults? Results from NHANES 2003–2016

Accumulating evidence linked bisphenol A (BPA) exposure with several diseases and even premature death. We aimed to evaluate the association between BPA exposure and mortality in US adults from the National Health and Nutrition Examination Survey (NHANES, 2003–2016), and to explore whether an anti-inflammatory diet can mitigate the deleterious effect of BPA on mortality. A cohort study including 8142 adults was conducted. Of these, 4143 (50.2%) were men, with a weighted average age of 55.9 years. Urinary BPA was measured by the on-line solid phase extraction, coupled to high performance liquid chromatography and tandem mass spectrometry. Dietary Inflammatory Index (DII) score was calculated based on 28 available kinds of food parameters in NHANES. Cox proportional hazards regression models were applied to calculate the hazard ratios (HRs) and 95% confidence intervals (CIs) for all-cause, cardiovascular disease (CVD), and cancer mortality. After 75927 person-years of follow-up (median, 9.3 years; maximum, 17.1 years), BPA exposure and DII score were independently associated with all-cause mortality. The fully-adjusted HR (95% CI) in the high versus low levels of BPA was 1.33 (1.05–1.70) for all-cause mortality, and the anti-inflammatory versus pro-inflammatory category of DII was 0.70 (0.56–0.87). There was no significant interaction between BPA and DII (p = 0.200). However, an indication of combined effect was found that, participants in subgroups with low BPA exposure and concurrently with anti-inflammatory category of DII score had 53% significantly lower all-cause mortality. Our findings highlight the importance of another monitoring cycles of BPA exposure, and its long-term adverse effects on health, even though the US government had restricted its use nowadays. Besides, we provided a new perspective against the adverse health effect induced by BPA exposure, that future studies could explore the offset impact of other healthy dietary patterns on the deleterious effect of BPA on health outcomes.

Sensitive Analysis of Recombinant Human Erythropoietin Glycopeptides by On-Line Phenylboronic Acid Solid-Phase Extraction Capillary Electrophoresis Mass Spectrometry.

In this study, several chromatographic sorbents: porous graphitic carbon (PGC), aminopropyl hydrophilic interaction (aminopropyl-HILIC), and phenylboronic acid (PBA) were assessed for the analysis of glycopeptides by on-line solid-phase extraction capillary electrophoresis mass spectrometry (SPE-CE-MS). As the PBA sorbent provided the most promising results, a PBA-SPE-CE-MS method was developed for the selective and sensitive preconcentration of glycopeptides from enzymatic digests of glycoproteins. Recombinant human erythropoietin (rhEPO) was selected as the model glycoprotein and subjected to enzymatic digestion with several proteases. The tryptic O126 and N83 glycopeptides from rhEPO were targeted to optimize the methodology. Under the optimized conditions, intraday precision, linearity, limits of detection (LODs), and microcartridge lifetime were evaluated, obtaining improved results compared to that from a previously reported TiO2-SPE-CE-MS method, especially for LODs of N-glycopeptides (up to 500 times lower than by CE-MS and up to 200 times lower than by TiO2-SPE-CE-MS). Moreover, rhEPO Glu-C digests were also analyzed by PBA-SPE-CE-MS to better characterize N24 and N38 glycopeptides. Finally, the established method was used to analyze two rhEPO products (EPOCIM and NeuroEPO plus), demonstrating its applicability in biopharmaceutical analysis. The sensitivity of the proposed PBA-SPE-CE-MS method improves the existing CE-MS methodologies for glycopeptide analysis and shows a great potential in glycoprotein analysis to deeply characterize protein glycosites even at low concentrations of the protein digest.

Probing Molecular-Level Dynamic Interactions of Dissolved Organic Matter with Iron Oxyhydroxide via a Coupled Microfluidic Reactor and an Online High-Resolution Mass Spectrometry System.

The interactions between dissolved organic matter (DOM) and iron (Fe) oxyhydroxide are crucial in regulating the biogeochemical cycling of nutrients and elements, including the preservation of carbon in soils. The mechanisms of DOM molecular assembly on mineral surfaces have been extensively studied at the mesoscale with equilibrium experiments, yet the molecular-level evolution of the DOM-mineral interface under dynamic interaction conditions is not fully understood. Here, we designed a microfluidic reactor coupled with an online solid phase extraction (SPE)-LC-QTOF MS system to continually monitor the changes in DOM composition during flowing contact with Fe oxyhydroxide at circumneutral pH, which simulates soil minerals interacting with constant DOM input. Time-series UV-visible absorption spectra and mass spectrometry data showed that after aromatic DOM moieties were first preferentially sequestered by the pristine Fe oxyhydroxide surface, the adsorption of nonaromatic DOM molecules with greater hydrophobicity, lower acidity, and lower molecular weights (<400) from new DOM solutions was favored. This is accompanied by a transition from mineral surface chemistry-dominated adsorption to organic-organic interaction-dominated adsorption. These findings provide direct molecular-level evidence to the zonal model of DOM assembly on mineral surfaces by taking the dynamics of interfacial interactions into consideration. This study also shows that coupled microfluidics and online high-resolution mass spectrometry (HRMS) system is a promising experimental platform for probing microscale environmental carbon dynamics by integrating in situ reactions, sample pretreatment, and automatic analysis.

Investigating the bioaccumulation potential of anionic organic compounds using a permanent rainbow trout liver cell line

Permanent rainbow trout (Oncorhynchus mykiss) cell lines represent potential in vitro alternatives to experiments with fish. We here developed a method to assess the bioaccumulation potential of anionic organic compounds in fish, using the rainbow trout liver-derived RTL-W1 cell line. Based on the availability of high quality in vivo bioconcentration (BCF) and biomagnification (BMF) data and the substances’ charge state at physiological pH, four anionic compounds were selected: pentachlorophenol (PCP), diclofenac (DCF), tecloftalam (TT) and benzotriazol-tert-butyl-hydroxyl-phenyl propanoic acid (BHPP). The fish cell line acute toxicity assay (OECD TG249) was used to derive effective concentrations 50 % and non-toxic exposure concentrations to determine exposure concentrations for bioaccumulation experiments. Bioaccumulation experiments were performed over 48 h with a total of six time points, at which cell, medium and plastic fractions were sampled and measured using high resolution tandem mass spectrometry after online solid phase extraction. Observed cell internal concentrations were over-predicted by KOW-derived predictions while pH-dependent octanol–water partitioning (DOW) and membrane lipid-water partitioning (DMLW) gave better predictions of cell internal concentrations. Measured medium and cell internal concentrations at steady state were used to calculate RTL-W1-based BCF, which were compared to DOW- or DMLW-based model approaches and in vivo data. With the exception of PCP, the cell-derived BCF best compared to DOW-based model predictions, which were higher than predictions based on DMLW. All methods predicted the in vivo BCF for diclofenac well. For PCP, the cell-derived BCF was lowest although all BCF predictions underestimated the in vivo BCF by ≥ 1 order of magnitude. The RTL-W1 cells, and all other prediction methods, largely overestimated in vivo BMF, which were available for PCP, TT and BHPP. We conclude that the RTL-W1 cell line can supplement BCF predictions for anionic compounds. For BMF estimations, however, in vitro-in vivo extrapolations need adaptation or a multiple cell line approach.

Liquid chromatography-tandem mass spectrometry analysis of delamanid and its metabolite in human cerebrospinal fluid using protein precipitation and on-line solid-phase extraction

The penetration of the antituberculosis drug delamanid into the central nervous system is not established. The distribution of delamanid and its major metabolite, DM-6705, into the cerebrospinal fluid requires investigation. A liquid chromatography-tandem mass spectrometry method for the quantification of delamanid and DM-6705 in human cerebrospinal fluid was developed and validated. The calibration range for both analytes was 0.300 – 30.0 ng/mL. The deuterium-labelled analogue of delamanid (delamanid-d4) and OPC-14714 were used as internal standards for delamanid and DM-6705, respectively. Samples were processed by protein precipitation followed by on-line solid-phase extraction and high-performance liquid chromatography on an Agilent 1260 HPLC system. A Phenomenex Gemini-NX C18 (5.0 µm, 50 mm × 2.0 mm) analytical column was used for on-line solid-phase extraction, and a Waters Xterra MS C18 (5.0 µm, 100 mm × 2.1 mm) analytical column for chromatographic separation using gradient elution, at a flow rate of 300 µL/min. The total run time was 7.5 min. Analytes were detected by multiple reaction monitoring on an AB Sciex 5500 triple quadrupole mass spectrometer at unit mass resolution, with electrospray ionization in the positive mode. Accuracy and precision were assessed over three independent validation batches. Extraction recoveries were more than 98% and were consistent across the analytical range. Both analytes in CSF exhibited non-specific adsorption to polypropylene tubes. The method was used to analyse cerebrospinal fluid samples from patients with pulmonary tuberculosis in an exploratory pharmacokinetic study.

Ionic liquid-functionalized dendrimer grafted silica for mixed-mode chromatographic separation and online solid-phase extraction

The efficient sample pretreatment and high-performance chromatographic separation are essential for an accurate analysis of the complex sample. Finding a material that can apply as both sorbent for sample preparation and stationary phase for chromatography is greatly important for analytical chemistry. With a large number of active sites and designable properties, the dendrimers displayed potential performance for sample preparation and chromatographic separation. In order to improve its selectivity restricted by the limited type of functional groups (amide, ethylidene, amino groups), ionic liquid (1,1′-(1,4-butyricdiyl)bis(1-aminopropyl imidazolium)dibromide) were introduced to functionalize dendrimers. With porous silica as the base, ionic liquid-functionalized dendrimer grafted silica (SiO2@G1.5-IL) was obtained and characterized by X-ray photoelectron spectroscopy, elemental analyzer, as well as specific surface and porosity analyzer. The material was used as stationary phase for mixed-mode chromatography and sorbent for SPE, respectively. Under reversed-phase liquid chromatography (RPLC), it successfully separated some hydrophobic analytes (five polycyclic aromatic hydrocarbons (PAHs), two bisphenols, diphenylpropane, and diphenylmethane), by utilizing hydrophobic, π-stacking and hydrogen bonding interactions. Based on the hydrophilic effect, it could separate hydrophilic analytes (nucleosides and alkaloids), which coincident with hydrophilic interaction liquid chromatography (HILIC). And it exhibited better separation capacity than NH2@SiO2 and SiO2@G1.5 under the above two modes. Furthermore, the thermodynamic parameters (ΔH, ΔS, and ΔG) of the above types of analytes on the SiO2@G1.5-IL column were also investigated in detail, revealing the controlling factors during the chromatographic separation. And the relative standard deviations (RSDs, 0.03–2.95%, n = 10) of the repeatability of chromatographic separation were satisfactory. After that, SiO2@G1.5-IL-based SPE column was online combined with high-performance liquid chromatography to investigate the extraction selectivity for three types of hydrophobic organic pollutants (PAHs, estrogens, and bisphenols), and compared to SiO2 and C18 columns. According to their extraction performance, PAHs were selected as the target analytes, and the online analytical method was established. The limits of detection were as low as 0.001 μg L-1 due to the high enrichment factor reach to 3869, limits of quantity were 0.003–0.17 μg L-1, linear ranges were from 0.003 to 15.0 µg L-1, the adsorption capacity was 16.10 μg g−1, as well as RSDs were 0.5–3.7%, 0.6–6.7%, and 4.2–9.0% for intraday, interday tests and reproducibility. Finally, it was applied to analyze the environmental water samples (tap water, snow water, and rainwater), and satisfactory results were obtained (spiked recoveries were 86.8%-120.9%). Therefore, SiO2@G1.5-IL was a powerful material that can be used for the chromatographic separation of both hydrophobic and hydrophilic samples by RPLC or HILIC mode, as well as the efficient online extraction of hydrophobic targets prior to C18 column-based high-performance liquid chromatography.

Dummy-template Pickering emulsion imprinted microspheres online pretreatment and analysis for the estrogens in cosmetics

Estrogens are a class of steroid hormone with strong physiological activity. Due to the pronounced beauty effect, such drugs are highly susceptible to illegal addition and cause other adverse effects. To avoid template leakage and the negative impacts on the environment caused by the estrogens, diosgenin was selected as the dummy template due to its similar skeleton structure. The Pickering emulsion polymerization was used to obtain the dummy-template molecularly imprinted polymers (dt-MIPs). Scanning electron microscopy, optical microscopy, specific surface area testing, Fourier transform infrared spectroscopy and adsorption experiments were used to characterize the apparent morphology and the recognition performance of the microspheres. Then, the prepared microspheres and commercial fillers were used to construct an on-line solid phase extraction (on-line SPE) analytical system coupled with HPLC via a two-position switching valve. On-line solid phase extraction-HPLC analytical methods were established and verified, for the simultaneous determination of four estrogens in cosmetic samples. The accuracy and precision RSDs for the established methods using the imprinted sorbents were 92.00–104.02% and less than 9.12%, respectively. All four estrogens exhibited good linearity in the range of 0.05 to 5 µg/mL with a coefficient of determination R2 greater than 0.9810. The method comparison results suggest that the established analytical method is simple in pre-treatment, easy to automate, and has excellent sensitivity to meet the analytical requirements of complex samples.