Omega Cm2 Research Articles

Direct Metallization Local Al-Back Surface Field for High Efficiency Screen Printed Crystalline Silicon Solar Cells

In this paper, we present a detailed study on the local back contact (LBC) formation of rear-surface-passivated silicon solar cells, where both the LBC opening and metallization are realized by one-step alloying of a dot of fine pattern screen-printed aluminum paste with the silicon substrate. Based on energy dispersive spectrometer (EDS) and scanning electron microscopy (SEM) characterizations, we suggest that the aluminum distribution and the silicon concentration determine the local-back-surface-field (Al-p+) layer thickness, resistivity of the Al-p+ and hence the quality of the Al-p+ formation. The highest penetration of silicon concentration of 78.17% in aluminum resulted in the formation of a 5 microm-deep Al-p+ layer, and the minimum LBC resistivity of 0.92 x 10-6 omega cm2. The degradation of the rear-surface passivation due to high temperature of the LBC formation process can be fully recovered by forming gas annealing (FGA) at temperature and hydrogen content of 450 degrees C and 15%, respectively. The application of the optimized LBC of rear-surface-passivated by a dot of fine pattern screen(-) printed aluminum paste resulted in efficiency of up to 19.98% for the p-type czochralski (CZ) silicon wafers with 10.24 cm2 cell size at 649 mV open circuit voltage. By FGA for rear-surface passivation recovery, efficiencies up to 20.35% with a V(OC) of 662 mV, FF of 82%, and J(SC) of 37.5 mA/cm2 were demonstrated.

Ohmic Contacts to <I>N</I>-Face p-GaN Using Ni/Au for the Fabrication of Polarization Inverted Light-Emitting Diodes

The electrical properties of Ni-based ohmic contacts to N-face p-type GaN were investigated. The specific contact resistance of N-face p-GaN exhibits a linear decrease from 1.01 omega cm2 to 9.05 x 10(-3) omega cm2 for the as-deposited and the annealed Ni/Au contacts, respectively, with increasing annealing temperature. However, the specific contact resistance could be decreased down to 1.03 x 10(-4) omega cm2 by means of surface treatment using an alcohol-based (NH4)2S solution. The depth profile data measured from the intensity of O1s peak in the X-ray photoemission spectra showed that the alcohol-based (NH4)2S treatment was effective in removing the surface oxide layer of GaN.

Toluene diisocyanate caused electrophysiological disturbances in the upper airways wall

Toluene diisocyanate (TDI) due to its widespread use in industry is one of the most common and well-known causes of occupational asthma and Reactive Airways Dysfunction Syndrome (RADS). In this study the impact of TDI on the electrophysiological properties of the airways wall, particularly on the mechanisms of absorption of sodium ions and chloride ions secretion was evaluated. Isolated rabbit tracheal wall (from outbred stock animals) was mounted in an apparatus for electrophysiological experiments by means of Ussing method and was mechanically stimulated by the jet flux of specified fluid directed onto the mucosal surface of the tissue from a peristaltic pump. The measured parameters were: transepithelial potential difference under control conditions (PD, mV), after mechanical stimulation (dPD or physiological reaction of hyperpolarization, mV) and electric resistance (R, Omega cm2). When TDI (0.035 mM) was added to stimulation fluid, only the immediate reaction was identified and when it was added to incubation fluid and other experimental fluids, the late (post-incubation) reaction was determined. The experiments involving the inhibition of Na+ by amiloride and Cl- by bumetanide were also performed. A series of functional tests for 72 pieces of tracheal wall from 36 animals were performed. It has been shown that short-term exposure to TDI significantly changed the course of reactions to mechanical stimulation. Also after incubation in the presence of TDI, the reactions to mechanical stimulation were changed in relation to control conditions. The immediate reaction of the isolated rabbit tracheal wall after exposure to TDI depends on the duration of exposure and on the physiological condition of the tissue in respect of sodium and chloride ion transport.

Quantification of the Internal Resistance Distribution of Microbial Fuel Cells

Identifying the limiting factors in a microbial fuel cell (MFC) system requires qualifying the contribution of each component of an MFC to internal resistance. In this study, a new method was developed to calculate the internal resistance distribution of an MFC. Experiments were conducted to identify the limiting factors in single-chamber MFCs by varying the anode surface areas, cathode surface areas, and phosphate buffer concentrations. For the MFCs with equally sized electrodes (7 cm2) and 200 mM phosphate buffer, the anode contributed just 5.4% of the internal resistance, while the cathode and the electrolyte each contributed 47.3%, indicating that the anode was not the limiting factor in power generation. The limitation of the cathode was further revealed by the 780% higher area-specific resistance (284.4 omega cm2) than the 32.3 omega cm2 of the anode. The electrolyte limitation was also evidenced by the greatly increased contribution of electrolyte in internal resistance from 47.3 to 78.2% when the concentration of phosphate buffer was decreased from 200 to 50 mM. An anodic power density of 6860 mW/m2 was achieved at a current density of 2.62 mA/cm2 using the MFCs with an anode/cathode area ratio of 1/14 and 200 mM phosphate buffer. The method was also successfully applied to analyze the internal resistance distribution of the two chamber MFCs from a previously reported study. The comparison of the internal resistances of the two air cathode systems indicates that the much lower resistances, including anode, cathode, and membrane resistances, contributed to the much better performance of the single-chamber MFCs than the two-chamber system.

Test Structures for the Characterization of MEMS and CMOS Integration Technology

Test structures have been used to study the feasibility of bonding MEMS to CMOS wafers to create an integrated system. This involves bonding of prefabricated wafers and creating interconnects between the bonded wafers. Bonding of prefabricated wafers has been demonstrated using a chemical-mechanical polishing enabled surface planarization process and an oxygen plasma assisted low temperature wafer bonding process. Two interwafer connection approaches have been evaluated. For an oxide bonding approach, interconnects between wafers are established through contact vias, using a standard multilevel metallization process after the wafer bonding process. Resistances of 3.8-5.2 Omega have been obtained from via chain test structures and an average specific contact resistivity of 1.7 X 10-8 Omega cm2, measured from the single via Kelvin structures. For a direct metal contact approach, electrical connections have been achieved during the bonding anneal stage due to stress relief of the aluminium film.

Evaluation of in vitro cytotoxicity and paracellular permeability of intact monolayers with mouse embryonic stem cells

Mouse embryonic stem (mES) cells were induced to form intact monolayers in cell culture inserts, using combinations of extracellular matrix (ECM) components and growth factors (GFs). Progressive formation of intact monolayers was monitored using transepithelial electrical resistance (TEER) and passage of paracellular permeability (PP) markers. The mES cells were initially inoculated on inactivated mouse embryonic fibroblasts (MEFs) plus leukemia inhibitory factor (LIF). At 75% confluence, cells were passaged in the absence of MEF and LIF to stimulate formation of rounded multicellular aggregates (MA). After 4 days, cultures containing MA were transferred to culture inserts coated with ECM components only, and grown in the presence of selected individual GFs. An additional 10-14 days revealed confluent monolayers with TEER values of 500-700 ohms cm2 (Omega cm2). Monolayers grown on inserts coated with ECM components, such as fibronectin or collagen-IV, in the presence of epidermal growth factor or keratinocyte growth factor in the medium, yielded the highest TEER measurements when compared to cultures grown without GFs or ECM. Acute cytotoxicity (AC) studies with confluent monolayers of mES cells in 96-well plates indicated that there is a high correlation (R2=0.91) between cell viability and TEER for 24-h exposure time. Also, decrease in TEER is inversely proportional with increase in PP of markers. In comparison to standardized Registry of Cytotoxicity (RC) data and TEER measurements, MTT IC50 values for mES cells are lower. Thus, at equivalent concentrations for the same chemicals, cell viability decreases before the integrity of the monolayer is compromised. This system represents a novel approach for the manipulation of mES cells toward specific intact monolayers, as an in vitro model for biological monolayer formation, and most importantly, for applications to cytotoxicity testing.

Source/Drain Engineering for Parasitic Resistance Reduction for Germanium p-MOSFETs

A reduction of parasitic resistance is presented with incorporation of preamorphization implantation (PAI) and self-aligned Cu3Ge in the source/drain region for germanium p-MOSFETs. Full activation of boron in the amorphous layer can be obtained during solid-phase epitaxial growth, and a concentration as high as 4 x 1020/cm3 is achieved. This nonthermal equilibrium concentration is maintained during the subsequent Cu3Ge formation. Cu3Ge is adopted as a contact metal in germanium p-MOSFETs for the first time, due to its superior electrical properties (6.8 muOmegaldrcm for resistivity and ~1 x 10-7 Omega cm2 on p-type germanium for specific contact resistance). The fabricated p+/n diode yields a five order of magnitude between forward and reverse currents, which can be attributed to the reduction in parasitic resistance. The low reverse current mitigates concerns of possible deep-level traps introduced by copper. It also confirms the nonexistence of extended defects created by PAI as a result of the unique role of vacancies in germanium. With high dopant concentrations achieved by PAI and low resistance of Cu3Ge, excellent MOSFET characteristics are demonstrated in self-aligned Cu3Ge p-MOSFETs. A 15% mobility enhancement over Si universal mobility and a 60% parasitic resistance reduction are achieved.

Influence of Applied Potential on the Impedance of Alkanethiol SAMs

Self-assembled monolayers are generally considered to behave as dielectric layers with a capacitance that is dependent on the monolayer thickness and the relative permittivity that is determined by the hydrocarbon tail. We show that the impedance response of alkanethiol-modified gold surfaces can be modeled as a parallel network consisting of the capacitance and resistance of the monolayer over a wide potential range. At potentials positive to -0.3 V (Ag/AgCl), the monolayer resistance is greater than 10(6) Omega cm2; however, at more negative potentials, the monolayer resistance decreases exponentially with potential with an inverse slope of about 250 mV. Over the same potential range, the monolayer capacitance is independent of potential. Although the same behavior is observed on ultrasmooth, template-stripped gold, the resistance at any potential is larger than for evaporated gold. The progressive increase in permeability of the monolayer is associated with an increase in electric field at potentials negative to the potential of zero charge.

Efficient proton conduction in dry nanofilms of amorphous aluminosilicate

Amorphous aluminosilicate nanofilms as prepared by a sol-gel process and post-annealing exhibit proton conduction at a wide temperature range in dry air with a lowest area specific resistance of 0.24 omega cm2 at 400 degrees C.

Porcine Alveolar Epithelial Cells in Primary Culture: Morphological, Bioelectrical and Immunocytochemical Characterization

The purpose of this study was to establish a primary culture of porcine lung epithelial cells as an alternative to the currently existing cell cultures from other species, such as e.g., rat or human. Primary porcine lung epithelial cells were isolated, cultivated and analyzed at distinct time points after isolation. The main part of the work focused on the morphology of the cells and the detection of alveolar epithelial cell markers by using electron microscopy, immunofluorescence microscopy and immunoblotting. Regarding a later use for in vitro pulmonary drug absorption studies the barrier properties of the cell monolayer were evaluated by monitoring bioelectrical parameters and by marker transport. Epithelial cells isolated from porcine lung grew to confluent monolayers with typical intercellular junctions within a few days. Maximum transepithelial resistance of about 2,000 Omega cm2 was achieved and demonstrated the formation of a tight epithelial barrier. Permeability data of sodium fluorescein recommended a minimal transepithelial resistance of 600 Omega cm2 for transport studies. The cell population changed from a heterogeneous morphology and marker distribution (caveolin-1, pro-SP-C, surface sugars) towards a monolayer consisting of two cell types resembling type I and type II pneumocytes. The porcine alveolar epithelial primary cell culture holds promise for drug transport studies, because it shares major hallmarks of the mammalian alveolar epithelium and it is easily available and scaled up for drug screening.

K+ secretion activated by luminal P2Y2 and P2Y4 receptors in mouse colon

Extracellular nucleotides are important regulators of epithelial ion transport, frequently exerting their action from the luminal side. Luminal P2Y receptors have previously been identified in rat distal colonic mucosa. Their activation by UTP and ATP stimulates K+ secretion. The aim of this study was to clarify which of the P2Y receptor subtypes are responsible for the stimulated K+ secretion. To this end P2Y2 and P2Y4 knock-out mice were used to measure distal colonic ion transport in an Ussing chamber. In mouse (NMRI) distal colonic mucosa, luminal UTP and ATP with similar potency induced a rapid and transient increase of the transepithelial voltage (V(te)) (UTP: from -0.81 +/- 0.23 to 3.11 +/- 0.61 mV, n = 24), an increase of equivalent short circuit current (I(sc)) by 166.9 +/- 22.8 microA cm(-2) and a decrease of transepithelial resistance (R(te)) from 29.4 +/- 2.4 to 23.5 +/- 2.0 Omega cm2. This effect was completely inhibited by luminal Ba2+ (5 mm, n = 5) and iberiotoxin (240 nm, n = 6), indicating UTP/ATP-stimulated K+ secretion. RT-PCR analysis of isolated colonic crypts revealed P2Y2, P2Y4 and P2Y6 specific transcripts. The luminal UTP-stimulated K+ secretion was still present in P2Y2 receptor knock-out mice, but significantly reduced (DeltaV(te): 0.83 +/- 0.26 mV) compared to wild-type littermates (DeltaV(te): 2.08 +/- 0.52 mV, n = 9). In P2Y4 receptor knock-out mice the UTP-induced K+ secretion was similarly reduced. Luminal UTP-stimulated K+ secretion was completely absent in P2Y2/P2Y4 double receptor KO mice. Basolateral UTP showed no effect. In summary, these results indicate that both the P2Y2 and P2Y4 receptors are present in the luminal membrane of mouse distal colonic mucosa, and stimulation of these receptors leads to K+ secretion.

Functional similarities between pleura and the renal proximal tubule – membrane and cellular considerations

The small amount of liquid that, under physiological conditions, is presented in the pleural cavity has been the focus of extensive research for more than a century. However, there are still unanswered questions and considerable controversies about the nature of the forces governing its movement into and out of the pleural cavity. Early in the 20th century has been proposed that pleural fluid turnover is simple based on the balance between hydraulic and colloid osmotic pressures existing across the pleural membranes. This original hypothesis has not been validated by data accumulating over the last 20 years. Pleural tissues and renal proximal tubules present high water permeability, small transepithelial electrical resistance (22.02 Omega cm2) and the same cation transportation such as Na+ channels, Na+-K+ ATPase channels, and Na+-H+ exchanger. In contrast to previous conflicting theories concerning pleura fluid movement, the same functional characteristics suggest the hypothesis that physiology of pleura is similar to proximal tubules.

Electrical Characteristics of Suburothelial Cells Isolated From the Human Bladder

We measured the membrane electrical characteristics as well as the response to adenosine triphosphate of cells isolated from the suburothelial layer of the bladder. Suburothelial cells were isolated from biopsy samples of human bladder by collagenase disruption. Electrophysiological measurements were done under current and voltage clamp to record membrane potential and ionic currents using patch pipettes with a K+ based filling solution. Intracellular [Ca2+] was measured with Fura-2. Cells were different from epithelial cells by their spindle-shaped appearance with projections at either end. The cells stained for vimentin but epithelial and smooth muscle cells did not. The cells had small membrane capacitance (27 +/- 16 pF) and a specific membrane resistance of 90 +/- 48 x 10(9) Omega cm2. Average membrane potential was -63 +/- 14 mV but cells showed spontaneous spikes or random fluctuations of membrane potential. A small net inward current was superimposed by a larger outward current. Inward current was attenuated by the removal of extracellular Ca. Outward current showed large spontaneous fluctuations and was greatly decreased by 30 mM tetraethyl ammonium chloride. Adenosine triphosphate (30 to 100 microM) elicited an inward current of about 50 pA and large intracellular Ca2+ transients. These cells are electrically active which, in conjunction with the previous observation of connexin 43 labeling, suggests that they could act as an electrical network. A quantitative model of voltage distribution in such a network after the generation of inward current suggests that individual cells could not act as pacemakers, but rather a group of simultaneously activated cells could exert a peripheral excitatory effect that would amplify the magnitude of the original response. The implications of this in terms of bladder sensation are discussed.

A redox-stable efficient anode for solid-oxide fuel cells.

Solid-oxide fuel cells (SOFCs) promise high efficiencies in a range of fuels. Unlike lower temperature variants, carbon monoxide is a fuel rather than a poison, and so hydrocarbon fuels can be used directly, through internal reforming or even direct oxidation. This provides a key entry strategy for fuel-cell technology into the current energy economy. Present development is mainly based on the yttria-stabilized zirconia (YSZ) electrolyte. The most commonly used anode materials are Ni/YSZ cermets, which display excellent catalytic properties for fuel oxidation and good current collection, but do exhibit disadvantages, such as low tolerance to sulphur and carbon deposition when using hydrocarbon fuels, and poor redox cycling causing volume instability. Here, we report a nickel-free SOFC anode, La0.75Sr0.25Cr0.5Mn0.5O3, with comparable electrochemical performance to Ni/YSZ cermets. The electrode polarization resistance approaches 0.2 Omega cm2 at 900 degrees C in 97% H2/3% H2O. Very good performance is achieved for methane oxidation without using excess steam. The anode is stable in both fuel and air conditions, and shows stable electrode performance in methane. Thus both redox stability and operation in low steam hydrocarbons have been demonstrated, overcoming two of the major limitations of the current generation of nickel zirconia cermet SOFC anodes.

Transcytosis of GCSF-transferrin across rat alveolar epithelial cell monolayers.

The purpose of this study was to use primary cultured rat alveolar epithelial cell monolayers to examine the potential of using transferrin receptor (TfR)-mediated transcytosis for noninvasive systemic protein drug delivery via the pulmonary route. Freshly isolated rat type II pneumocytes were plated onto tissue culture-treated polycarbonate 12-mm Transwells. AEC monolayers (> or = 2500 omega(cm2)) were treated with keratinocyte growth factor (10 ng/mL) for maintenance of type II cell-like characteristics. Filgrastim (GCSF)-Tf conjugates were prepared using the linkers SPDP and DPDPB. TfR-specific binding and uptake were determined using 125I-Tf and 59Fe-Tf treatment, respectively. Apical-to-basolateral (A-to-B) transferrin receptor (TfR)-mediated transcytosis was determined by dosing the apical compartment with 1.5 microg/mL of 125I-Tf or 125I-GCSF-Tf. Nonspecific TfR-independent transport of 125I-Tf and 125I-GCSF-Tf was determined in parallel by including 150 microg/mL of nonradiolabeled Tf. Basolateral samples (500 microL) were taken at 2, 4, and 6 h post-dosing, subjected to 15% trichloroacetic acid precipitation, and assayed in a Packard gamma counter. TfR-specific transport was determined as the difference between total and nonspecifc transport. The effects of brefeldin-A (BFA) on TfR distribution and (A-to-B) transport of 125I-Tf, 125I-GCSF and 125I-GCSF-Tf was studied by including the agent in the apical fluid at 1 microg/mL. BFA treatment resulted in a small significant reduction in TfR at the basolateral surface of type II cell-like monolayers, while it had no effect on TfR distribution in type I cell-like monolayers. In contrast, BFA treatment significantly altered the endocytosis of TfR, reducing the basolateral uptake of 59Fe-Tf while greatly increasing the apical uptake of 59Fe-Tf. BFA treatment, however, did not affect the TfR-specific uptake of 59Fe-Tf in type I cell-like monolayers. TfR-specific apical-to-basolateral transcytosis of 125I-Tf and 126I-GCSF-Tf conjugates was significantly enhanced in the presence of BFA in type II cell-like monolayers, whereas it had no effect on apical-to-basolateral transport of 125I-GCSF. BFA-enhanced transport of 125I-GCSF-Tf was approximately 3-fold higher than that of 125I-GCSF in the presence or absence of BFA. Moreover, 125I-GCSF transport in the presence of BFA was not significantly different from non-specific 125I-GCSF-Tf transport. Chromatographic analyses and bio-assays revealed that GCSF-Tf was not degraded during transport via TfR-specific processes, and that GCSF retained biologic activity when liberated from the conjugate via dithiothreitol reduction. This study suggests the possibility of using TfR-mediated transcytosis for systemic delivery of therapeutic proteins via the alveolar epithelium.

High-resistance MDCK-C7 monolayers used for measuring invasive potency of tumour cells.

We describe an electrophysiological method for evaluating the intrinsic invasive potency of tumour cells using renal cells as an in vitro assay system. A high-resistance clone of Madin-Darby canine kidney cells (MDCK-C7) was grown to confluency in a filter cup. Transepithelial electrical resistance across the MDCK-C7 monolayer was measured in a commercially available electrode chamber. After a transepithelial electrical resistance of about 4,000 omega cm2 had been reached, human melanoma or pancreatic carcinoma cells were co-cultivated with the MDCK-C7 monolayer. Both carcinoma cell lines induced resistance breakdown measured after 24 h or later depending on seeding density and cell type. Seeding carcinoma cells on the basolateral surface of MDCK-C7 cells caused a similar decrease in transepithelial resistance of the MDCK-C7 monolayer. Resistance breakdown indicates opening of tight junctions prior to tumour cell invasion. In conclusion, the high-resistance MDCK-C7 cell clone could serve as a valuable biological assay system to determine electrically the metastatic potency of tumour cells in vitro.

Formation of multilayers in the caco-2 cell culture model: a confocal laser scanning microscopy study.

To introduce confocal laser scanning microscopy (CLSM) combined with digital image restoration to characterise Caco-2 cells under different culture conditions, and thus to define additional valid criteria for the optimisation of culture models. Growth curves were established and transepithelial electrical resistance (TEER) measured for cells grown in EMEM or DMEM medium on Cyclopore membranes. Cytoskeleton, cell nuclei and tight junctions (TJ) were investigated by CLSM. Cultures reached a plateau of approximately 4.5 x 10(5) cells/cm2 after approximately 10 days. At the same time TEER reached 750 omega cm2. An irregular, fairly complete network of TJ was present at confluence (approximately 2 d). Between 15 and 30 days a regular TJ network was established. Cells formed mixed mono- and multilayers under most conditions with two exceptions: flat monolayers were observed on polycarbonate filters with EMEM and with the Biocoat intestinal epithelium differentiation environment system. In multilayers TJ were found in the upper as well as in the lower cell layers although the regular vertical polarity was disturbed. CLSM represents an important tool to investigate the cytoarchitecture of Caco-2 cells. 3D-analysis of confocal data gives important clues on the characteristics of cell layers and thus helps to validate optimisation strategies.

Primary Uroepithelial Cultures: A MODEL SYSTEM TO ANALYZE UMBRELLA CELL BARRIER FUNCTION

Despite almost 25 years of effort, the development of a highly differentiated and functionally equivalent cell culture model of uroepithelial cells has eluded investigators. We have developed a primary cell culture model of rabbit uroepithelium that consists of an underlying cell layer that interacts with a collagen substratum, an intermediate cell layer, and an upper cell layer of large (25-100 micrometer) superficial cells. When examined at the ultrastructural level, the superficial cells formed junctional complexes and had an asymmetric unit membrane, a hallmark of terminal differentiation in bladder umbrella cells. These cultured "umbrella" cells expressed uroplakins and a 27-kDa uroepithelial specific antigen that assembled into detergent-resistant asymmetric unit membrane particles. The cultures had low diffusive permeabilities for water (2.8 x 10(-4) cm/s) and urea (3.0 x 10(-7) cm/s) and high transepithelial resistance (>8000 Omega cm2) was achieved when 1 mM CaCl2 was included in the culture medium. The cell cultures expressed an amiloride-sensitive sodium transport pathway and increases in apical membrane capacitance were observed when the cultures were osmotically stretched. The described primary rabbit cell culture model mimics many of the characteristics of uroepithelium found in vivo and should serve as a useful tool to explore normal uroepithelial function as well as dysfunction as a result of disease.

Regulation of Cl- secretion in seawater fish (Dicentrarchus labrax) gill respiratory cells in primary culture.

1. Primary cultures of sea bass (Dicentrarchus labrax) gill cells grown on permeable membranes form a highly differentiated tight epithelium composed of respiratory-like cells. This preparation was also found to provide a functional model for investigating the hormonal regulation of Cl- secretion. 2. In control conditions, i.e. in the absence of hormones or other stimuli, the cultured epithelium showed a short-circuit current (Isc) of 8.8 +/- 0.4 microA cm-2, a transepithelial potential (Vt) of 28.6 +/- 0.6 mV (serosal side positive), and a transepithelial resistance (Rt) of 5026 +/- 127 Omega cm2. Addition of 50 nM PGE2 caused a stimulation of Isc, Vt and transepithelial conductance, Gt. The increase in Isc was probably due to the elevation in Cl- secretion, since it could be correlated with the stimulation of serosal to mucosal 36Cl- flux. Application of the neurohypophyseal peptide arginine vasotocin (AVT; 50 nM) or the beta-adrenergic agonist isoproterenol (isoprenaline; 0. 5 microM) evoked a stimulation in Cl- secretion, as was shown by the increases in Isc and Gt. The excitatory effect of isoproterenol followed by the inhibitory action of propranolol, a beta-adrenergic antagonist, suggested the presence of beta-adrenergic receptors. Noradrenaline (0.1 microM) elicited a reduction in Isc, Vt and Gt, which was counterbalanced by the addition of phentolamine, an alpha-adrenergic antagonist. This suggested an activation of alpha-adrenergic receptors. 3. This study provides evidence for hormonal control of the Cl- secretion in sea bass gill respiratory cells in culture, involving AVT, prostaglandin (PGE2), and beta- and alpha-adrenergic receptors.

Passive electrotonic properties of rat hippocampal CA3 interneurones.

1. The linear membrane responses of CA3 interneurones were determined with the use of whole-cell patch recording methods. The mean input resistance (RN) for all cells in this study was 526 +/- 16 MOmega and the slowest membrane time constant (tau0) was 73 +/- 3 ms. 2. The three-dimensional morphology of 63 biocytin-labelled neurones was used to construct compartmental models. Specific membrane resistivity (Rm) and specific membrane capacitance (Cm) were estimated by fitting the linear membrane response. Acceptable fits were obtained for 24 CA3 interneurones. The mean Rm was 61.9 +/- 34.2 Omega cm2 and the mean Cm was 0.9 +/- 0.3 microF cm-2. Intracellular resistance (Ri) could not be resolved in this study. 3. Examination of voltage attenuation revealed a significantly low synaptic efficiency from most dendritic synaptic input locations to the soma. 4. Simulations of excitatory postsynaptic potentials (EPSPs) were analysed at both the site of synaptic input and at the soma. There was little variability in the depolarization at the soma from synaptic inputs placed at different locations along the dendritic tree. The EPSP amplitude at the site of synaptic input was progressively larger with distance from the soma, consistent with a progressive increase in input impedance. 5. The 'iso-efficiency' of spatially different synaptic inputs arose from two opposing factors: an increase in EPSP amplitude at the synapse with distance from the soma was opposed by a nearly equivalent increase in voltage attenuation. These simulations suggest that, in these particular neurones, the amplitude of EPSPs measured at the soma will not be significantly affected by the location of synaptic inputs.