Rate Constants For OH Research Articles

Degradation of quinolone antibiotic, norfloxacin, in aqueous solution using gamma-ray irradiation.

This study reports the efficiency of gamma-ray irradiation to degrade quinolone antibiotic, norfloxacin, in aqueous solution. Laboratory batch experiments were conducted to determine the "pseudo-first" order degradation kinetics of norfloxacin in the concentration ranges of 3.4-16.1mgL(-1) by gamma-ray irradiation. The dose constant was found to be dependent on the initial concentration of norfloxacin and gamma-ray irradiation dose rate (D r). The saturation of norfloxacin sample solutions with N2, air or N2O, and the presence of tert-butanol and 2-propanol showed that (•)OH played more crucial role in the degradation of norfloxacin. The second order rate constants of (•)OH, eaq (-), and (•)H with norfloxacin were calculated to be 8.81 × 10(9), 9.54 × 10(8), and 1.10 × 10(9)M(-1)s(-1), respectively. The effects of various additives including CO3 (2-), HCO3 (-), NO3 (-), NO2 (-), and thiourea and the pH of the medium on the degradation of norfloxacin were also investigated. Norfloxacin degradation was lower in surface water and wastewater than in ultrapure water. Several degradation byproducts of norfloxacin were identified from which the possible degradation pathway was proposed.

Kinetics and Products of the Reaction of the First-Generation Isoprene Hydroxy Hydroperoxide (ISOPOOH) with OH.

The atmospheric oxidation of isoprene by the OH radical leads to the formation of several isomers of an unsaturated hydroxy hydroperoxide, ISOPOOH. Oxidation of ISOPOOH by OH produces epoxydiols, IEPOX, which have been shown to contribute mass to secondary organic aerosol (SOA). We present kinetic rate constant measurements for OH + ISOPOOH using synthetic standards of the two major isomers: (1,2)- and (4,3)-ISOPOOH. At 297 K, the total OH rate constant is 7.5 ± 1.2 × 10(-11) cm(3) molecule(-1) s(-1) for (1,2)-ISOPOOH and 1.18 ± 0.19 × 10(-10) cm(3) molecule(-1) s(-1) for (4,3)-ISOPOOH. Abstraction of the hydroperoxy hydrogen accounts for approximately 12% and 4% of the reactivity for (1,2)-ISOPOOH and (4,3)-ISOPOOH, respectively. The sum of all H-abstractions account for approximately 15% and 7% of the reactivity for (1,2)-ISOPOOH and (4,3)-ISOPOOH, respectively. The major product observed from both ISOPOOH isomers was IEPOX (cis-β and trans-β isomers), with a ∼ 2:1 preference for trans-β IEPOX and similar total yields from each ISOPOOH isomer (∼ 70-80%). An IEPOX global production rate of more than 100 Tg C each year is estimated from this chemistry using a global 3D chemical transport model, similar to earlier estimates. Finally, following addition of OH to ISOPOOH, approximately 13% of the reactivity proceeds via addition of O2 at 297 K and 745 Torr. In the presence of NO, these peroxy radicals lead to formation of small carbonyl compounds. Under HO2 dominated chemistry, no products are observed from these channels. We suggest that the major products, highly oxygenated organic peroxides, are lost to the chamber walls. In the atmosphere, formation of these compounds may contribute to organic aerosol mass.

Critical factors in sonochemical degradation of fumaric acid

The effects of critical factors such as Henry’s Law constant, atmospheric OH rate constant, initial concentration, H2O2, FeSO4 and tert-butanol on the sonochemical degradation of fumaric acid have been investigated. The pseudo first-order rate constant for the sonochemical degradation of 1mM fumaric acid is much lower than those for chloroform and phenol degradation, and is related to solute concentration at the bubble/water interface and reactivity towards hydroxyl radicals. Furthermore, fumaric acid is preferentially oxidized at the lower initial concentration. It is unreactive to H2O2 under agitation at room temperature. However, the degradation rate of fumaric acid increases with the addition of H2O2 under sonication. 0.1mM of fumaric acid suppresses H2O2 formation thanks to water sonolysis, while degradation behavior is also dramatically affected by the addition of an oxidative catalyst (FeSO4) or radical scavenger (tert-butanol), indicating that the degradation of fumaric acid is caused by hydroxyl radicals generated during the collapse of high-energy cavities.

Photocatalytic degradation of three amantadine antiviral drugs as well as their eco-toxicity evolution

Abstracts Advanced oxidation processes (AOPs) relying on in situ generated highly reactive OH are successfully applied to water purification. The absolute reaction rate constants for OH with three antiviral drugs were first reported through pulsed radiolysis experiments. Results found that OH reacted quickly with these substrates, with bimolecular reaction rate constants of 6.31 × 10 9 , 5.13 × 10 9 , and 7.05 × 10 9 M −1 s −1 for 1-amantadine, 2-amantadine, and rimantadine, respectively. The photocatalytic degradation kinetics of substrates were followed pseudo-first-order kinetics according to Langmuir–Hinshelwood model in TiO 2 suspensions, and the apparent rate constants were obtained as 0.076, 0.084, and 0.102 min −1 for three antiviral drugs, respectively. Scavenger experiments revealed that OH was the major reactive species involved in antiviral drugs degradation. To probe the photocatalytic degradation mechanism, the fate of nitrogen elements and the change of total organic carbon were also examined, and the data showed that all three drugs could be completely mineralized into CO 2 , H 2 O, and inorganic ions (NO 3 − and NH 4 + ) without generating any detectable products with enough degradation time. To further insight into the potential adverse effect of three antiviral drugs and their degradation products, the acute aquatic toxicity of degradation solutions were evaluated at three different trophic levels, and the toxicities first increased slightly and then decreased rapidly as the total organic carbon decreased.

Kinetic and mechanistic study of the reaction of OH radicals with methylated benzenes: 1,4-dimethyl-, 1,3,5-trimethyl-, 1,2,4,5-, 1,2,3,5- and 1,2,3,4-tetramethyl-, pentamethyl-, and hexamethylbenzene.

The reaction of OH radicals with a series of methylated benzenes was studied in a temperature range 300-350 K using a flash-photolysis resonance fluorescence technique. Reversible OH additions led to complex OH decays dependent on the number of distinguishable adducts. Except for hexamethylbenzene, triexponential OH decay curves were obtained, consistent with formation of at least two adduct species. For three compounds that can strictly form two adduct isomers for symmetry reasons (1,4-dimethyl-, 1,3,5-trimethyl-, and 1,2,4,5-tetramethylbenzene) with OH bound ortho or ipso with respect to the methyl groups, OH decay curves were analysed in terms of a reaction mechanism in which the two adducts can be formed directly by OH addition or indirectly by isomerization. In all cases one adduct (add1) is dominating the decomposition back to OH. The other (add2) is more elusive and only detectable at elevated temperatures, similar to the single OH adduct of hexamethylbenzene. Two limiting cases of the general reaction mechanism could be examined quantitatively: reversible formation of add2 exclusively in the OH reaction or by isomerization of add1. Total OH rate constants, adduct loss rate constants and products of forward and reverse rate constants of reversible reactions were determined. From these quantities, adduct yields, equilibrium constants, as well as reaction enthalpies and entropies were derived for the three aromatics. Adduct yields strongly depend on the selected reaction model but generally formation of add1 predominates. For both models equilibrium constants of OH reactions lie between those of OH + benzene from the literature and those obtained for OH + hexamethylbenzene. The corresponding reaction enthalpies of add1 and add2 formations are in a range -87 ± 20 kJ mol(-1), less exothermic than for hexamethylbenzene (-101 kJ mol(-1)). Reaction enthalpies of possible add1 → add2 isomerizations are comparatively small. Because results for 1,3,5-trimethylbenzene are partly inconsistent with a direct formation of add2, we promote the existence of isomerization reactions. Moreover, based on available theoretical work in the literature, add1 and add2 are tentatively identified as ortho and ipso adducts, respectively. Total OH rate constants were obtained for all title compounds. They can be described by Arrhenius equations: kOH = A × exp(-B/T). The parameters ln(A/(cm(3) s(-1))) = -25.6 ± 0.3, -25.3 ± 0.6, -27.3 ± 0.3, -24.6 ± 0.3, -26.2 ± 0.4, -26.2 ± 0.4 and -24.5 ± 0.2, and B/K = -160 ± 90, -550 ± 180, -1120 ± 90, -330 ± 100, -820 ± 100, -980 ± 130, and -570 ± 40 were determined for 1,4-dimethyl-, 1,3,5-trimethyl-, 1,2,4,5-, 1,2,3,5- and 1,2,3,4-tetramethyl-, pentamethyl-, and hexamethylbenzene.

Kinetics of the reactions of isoprene-derived hydroxynitrates: gas phase epoxide formation and solution phase hydrolysis

Abstract. Isoprene, the most abundant non-methane volatile organic compound (VOC) emitted into the atmosphere, is known to undergo gas phase oxidation to form eight different hydroxynitrate isomers in "high-NOx" environments. These hydroxynitrates are known to affect the global and regional formation of ozone and secondary organic aerosol (SOA), as well as affect the distribution of nitrogen. In the present study, we have synthesized three of the eight possible hydroxynitrates: 4-hydroxy-3-nitroxy isoprene (4,3-HNI) and E / Z-1-hydroxy-4-nitroxy isoprene (1,4-HNI). Oxidation of the 4,3-HNI isomer by the OH radical was monitored using a flow tube chemical ionization mass spectrometer (FT-CIMS), and its OH rate constant was determined to be (3.64 ± 0.41) × 10−11 cm3 molecule−1 s−1. The products of 4,3-HNI oxidation were monitored, and a mechanism to explain the products was developed. An isoprene epoxide (IEPOX) – a species important in SOA chemistry and thought to originate only from "low-NOx" isoprene oxidation – was found as a minor, but significant, product. Additionally, hydrolysis kinetics of the three synthesized isomers were monitored with nuclear magnetic resonance (NMR). The bulk, neutral solution hydrolysis rate constants for 4,3-HNI and the 1,4-HNI isomers were (1.59 ± 0.03) × 10−5 s−1 and (6.76 ± 0.09) × 10−3 s−1, respectively. The hydrolysis reactions of each isomer were found to be general acid-catalyzed. The reaction pathways, product yields and atmospheric implications for both the gas phase and aerosol phase reactions are discussed.

High temperature measurements for the rate constants of C1–C4 aldehydes with OH in a shock tube

The overall rate constants for the reactions of hydroxyl radicals (OH) with a series of aldehydes, formaldehyde (CH2O), acetaldehyde (CH3CHO), propionaldehyde (C2H5CHO) and n-butyraldehyde (n-C3H7CHO), were studied behind reflected shock waves at temperatures of 950–1400K and pressures of 1–2atm. OH radicals were produced by rapid thermal decomposition of tert-butyl hydroperoxide (TBHP), and OH time-histories were monitored by narrow-linewidth UV laser absorption of the well-characterized R1(5) line in the OH A-X (0, 0) band near 306.69nm. The overall rate constants were inferred by fitting simulated OH profiles to the measured OH time histories using detailed mechanisms of Veloo et al. (2013), USC Mech-II (2007) and GRI Mech 3.0. The measured high-temperature aldehydes+OH rate constants can be expressed in modified Arrhenius equations, in units of cm3mol−1s−1 and K, askCH2O=1.02×107T1.92exp(779/T)±13%kCH3CHO=4.32×106T2.02exp(716K/T)±22%kC2H5CHO=5.94×106T1.98exp(823K/T)±27%knC3H7CHO=5.36×106T2.06exp(658K/T)±25%No pressure dependence was observed in these measurements. The measured rate constant for the formaldehyde+OH reaction is consistent with previous experimental work from Vasudevan et al. (2005) within ±25%. For C2–C4 aldehydes+OH, this study provides the first direct rate constant measurement at high temperatures. More general rate constant expressions covering a much wider temperature range (200–1400K) were also determined by combining current measurements with existing low temperature data in the literature. These wide-range expressions were seen to be in excellent agreement with most existing experimental data.

Atmospheric photochemistry of aromatic hydrocarbons: OH budgets during SAPHIR chamber experiments

Abstract. Current photochemical models developed to simulate the atmospheric degradation of aromatic hydrocarbons tend to underestimate OH radical concentrations. In order to analyse OH budgets, we performed experiments with benzene, toluene, p-xylene and 1,3,5-trimethylbenzene in the atmosphere simulation chamber SAPHIR. Experiments were conducted under low-NO conditions (typically 0.1–0.2 ppb) and high-NO conditions (typically 7–8 ppb), and starting concentrations of 6–250 ppb of aromatics, dependent on OH rate constants. For the OH budget analysis a steady-state approach was applied in which OH production and destruction rates (POH and DOH) have to be equal. The POH were determined from measurements of HO2, NO, HONO, and O3 concentrations, considering OH formation by photolysis and recycling from HO2. The DOH were calculated from measurements of the OH concentrations and total OH reactivities. The OH budgets were determined from DOH/POH ratios. The accuracy and reproducibility of the approach were assessed in several experiments using CO as a reference compound where an average ratio DOH/POH = 1.13 ± 0.19 was obtained. In experiments with aromatics, these ratios ranged within 1.1–1.6 under low-NO conditions and 0.9–1.2 under high-NO conditions. The results indicate that OH budgets during photo-oxidation experiments with aromatics are balanced within experimental accuracies. Inclusion of a further, recently proposed OH production via HO2 + RO2 reactions led to improvements under low-NO conditions but the differences were small and insignificant within the experimental errors.

Prediction of micropollutant elimination during ozonation of a hospital wastewater effluent

Determining optimal ozone doses for organic micropollutant elimination during wastewater ozonation is challenged by the presence of a large number of structurally diverse micropollutants for varying wastewater matrice compositions. A chemical kinetics approach based on ozone and hydroxyl radical (OH) rate constant and measurements of ozone and OH exposures is proposed to predict the micropollutant elimination efficiency. To further test and validate the chemical kinetics approach, the elimination efficiency of 25 micropollutants present in a hospital wastewater effluent from a pilot-scale membrane bioreactor (MBR) were determined at pH 7.0 and 8.5 in bench-scale experiments with ozone alone and ozone combined with H2O2 as a function of DOC-normalized specific ozone doses (gO3/gDOC). Furthermore, ozone and OH exposures, OH yields, and OH consumption rates were determined. Consistent eliminations as a function of gO3/gDOC were observed for micropollutants with similar ozone and OH rate constants. They could be classified into five groups having characteristic elimination patterns. By increasing the pH from 7.0 to 8.5, the elimination levels increased for the amine-containing micropollutants due to the increased apparent second-order ozone rate constants while decreased for most micropollutants due to the diminished ozone or OH exposures. Increased OH quenching by effluent organic matter and carbonate with increasing pH was responsible for the lower OH exposures. Upon H2O2 addition, the elimination levels of the micropollutants slightly increased at pH 7 (<8%) while decreased considerably at pH 8.5 (up to 31%). The elimination efficiencies of the selected micropollutants could be predicted based on their ozone and OH rate constants (predicted or taken from literature) and the determined ozone and OH exposures. Reasonable agreements between the measured and predicted elimination levels were found, demonstrating that the proposed chemical kinetics method can be used for a generalized prediction of micropollutant elimination during wastewater ozonation. Out of 67 analyzed micropollutants, 56 were present in the tested hospital wastewater effluent. Two-thirds of the present micropollutants were found to be ozone-reactive and efficiently eliminated at low ozone doses (e.g., >80% for gO3/gDOC = 0.5).

Shock tube measurements of the rate constants for seven large alkanes + OH

Reaction rate constants for seven large alkanes+hydroxyl (OH) radicals were measured behind reflected shock waves using OH laser absorption. The alkanes, n-hexane, 2-methyl-pentane, 3-methyl-pentane, 2,2-dimethyl-butane, 2,3-dimethyl-butane, 2-methyl-heptane, and 4-methyl-heptane, were selected to investigate the rates of site-specific H-abstraction by OH at secondary and tertiary carbons. Hydroxyl radicals were monitored using narrow-line-width ring-dye laser absorption of the R1(5) transition of the OH spectrum near 306.7nm. The high sensitivity of the diagnostic enabled the use of low reactant concentrations and pseudo-first-order kinetics. Rate constants were measured at temperatures ranging from 880K to 1440K and pressures near 1.5atm. High-temperature measurements of the rate constants for OH+n-hexane and OH+2,2-dimethyl-butane are in agreement with earlier studies, and the rate constants of the five other alkanes with OH, we believe, are the first direct measurements at combustion temperatures. Using these measurements and the site-specific H-abstraction measurements of Sivaramakrishnan and Michael (2009) [1,2], general expressions for three secondary and two tertiary abstraction rates were determined as follows (the subscripts indicate the number of carbon atoms bonded to the next-nearest-neighbor carbon):S20=1.58×10-11exp(-1550K/T)cm3molecule-1s-1(887–1327K)S30=2.37×10-11exp(-1850K/T)cm3molecule-1s-1(887–1327K)S21=4.5×10-12exp(-793.7K/T)cm3molecule-1s-1(833–1440K)T100=2.85×10-11exp(-1138.3K/T)cm3molecule-1s-1(878–1375K)T101=7.16×10-12exp(-993K/T)cm3molecule-1s-1(883–1362K)

Effects of Reagent Rotation and Vibration on H + OH (υ, j)→ O + H2

The dynamics of the reaction H + OH → O ((3)P) + H2 have been studied in a series of quasi-classical trajectory (QCT) calculations and transition state theory (TST) methods using high quality (3)A' and (3)A″ potential energy surfaces (PESs). Accurate OH (υ, j) state resolved cross sections and rate constants on both potential energy surfaces are presented and fitted for OH at (υ = 0, j = 0-16) and (υ = 1, j = 0-6). The cross sections were calculated for different collisional energies (Ec), ranging from the threshold energy at each specific rovibrational state up to 1.0 eV with step sizes of 0.1 eV or less. They increase steeply with collision energy when the barrier to reaction can be overcome, after which the cross sections stay nearly constant with energy. State resolved rate constants in the temperature range 200-2500 K are presented based on the cross sections. Total thermal rate constants were calculated by summing the rates for reaction on the (3)A' and (3)A″ potential energy surfaces weighted by 1/3 and taking into account the thermal populations of the rovibrational states of the OH molecules. The currently calculated thermal rate constants generally agree well with previous indirectly obtained rate constants by Tsang et al. (Tsang, W.; Hampson, R. F. Chemical Kinetic Data Base for Combustion Chemistry. Part I. Methane and Related Compounds. J. Phys. Chem. Ref. Data 1986, 15, 1087-1279). It is shown that the improved canonical variational transition (CVT) treatments with the approximation of zero-curvature tunneling (ZCT) or small-curvature tunneling (SCT) produce results more in accord with the QCT results than the TST and CVT methods. The reactions are governed by the direct reaction mechanism. The rate constants for OH in excited vibrational and rotational states are orders of magnitude larger than the thermal rate constants, which needs to be taken into account in astrochemical models.

Rate Constants and Products of the OH Reaction with Isoprene-Derived Epoxides

Recent laboratory and field work has shown that isoprene-derived epoxides (IEPOX) are crucial intermediates that can explain the existence of a variety of compounds found in ambient secondary organic aerosol (SOA). However, IEPOX species are also able to undergo gas phase oxidation, which competes with the aerosol phase processing of IEPOX. In order to better quantify the atmospheric fate of IEPOX, the gas phase OH reaction rate constants and product formation mechanisms have been determined using a flow tube chemical ionization mass spectrometry technique. The new OH rate constants are generally larger than previous estimations and some features of the product mechanism are well predicted by the Master Chemical Mechanism Version 3.2 (MCM v3.2), while other features are at odds with MCM v3.2. Using a previously proposed kinetic model for the quantitative prediction of the atmospheric fate of IEPOX, it is found that gas phase OH reaction is an even more dominant fate for chemical processing of IEPOX than previously suggested. The present results suggest that aerosol phase processing of IEPOX will be competitive with gas phase OH oxidation only under SOA conditions of high liquid water content and low pH.

The •OH Radical Yield in the H2O2 + O3 (Peroxone) Reaction

The peroxone process is one of the AOPs that lead to (•)OH. Hitherto, it has been generally assumed that the (•)OH yield is unity with respect to O3 consumption. Here, experimental data are presented that suggest that it must be near 0.5. The first evidence is derived from competition experiments. The consumption of 4-chlorobenzoic acid (4-CBA), 4-nitrobenzoic acid (4-NBA) and atrazine present in trace amounts (1 μM) has been followed as a function of the O3 concentration in a solution containing H2O2 (1 mM) and tertiary butanol (tBuOH, 0.5 mM) in excess over the trace compounds. With authentic (•)OH generated by γ-radiolysis such a competition can be adequately fitted by known (•)OH rate constants. Fitting the peroxone data, however, the consumption of the trace indicators can only be rationalized if the (•)OH yield is near 0.5 (4-CBA: 0.56, 4-NBA: 0.49, atrazine: 0.6). Additional information for an (•)OH yield much below unity has been obtained by a product analysis of the reactions of tBuOH with (•)OH and dimethyl sulfoxide with (•)OH. The mechanistic interpretation for the low (•)OH yield is as follows (Merényi et al. Environ. Sci. Technol. 2010, 44, 3505-3507). In the reaction of O3 with HO2(-) an adduct (HO5(-)) is formed that decomposes into O3(•-) and HO2(•) in competition with 2 O2 + OH(-). The latter process reduces the free-radical yield.

Absolute and relative rate constants for the reactions of OH and Cl with pentanols

The rate constants for the reactions of OH with three pentanols have been determined in the range 267−373K and P=100Torr. The data obtained were (in units of cm3molecule−1s−1): k(1-pentanol)=(6.7±3.8)×10−12 exp [(132±176)/T], k(2-pentanol)=(5.2±1.8)×10−12 exp [(218±116)/T], k(3-pentanol)=(5.8±2.3)×10−12 exp [(164±118)/T]. The present work provides the first temperature dependence data on these reactions. In addition, using the relative rate method, the rate constants for OH and Cl with these pentanols have been measured. The results are compared with the literature data and discussed with respect to atmospheric chemistry.

Detailed chemical characterization of unresolved complex mixtures in atmospheric organics: Insights into emission sources, atmospheric processing, and secondary organic aerosol formation

Recent studies suggest that semivolatile organic compounds (SVOCs) are important precursors to secondary organic aerosol (SOA) in urban atmospheres. However, knowledge of the chemical composition of SVOCs is limited by current analytical techniques, which are typically unable to resolve a large number of constitutional isomers. Using a combination of gas chromatography and soft photoionization mass spectrometry, we characterize the unresolved complex mixture (UCM) of semivolatile aliphatic hydrocarbons observed in Pasadena, California (~16 km NE of downtown Los Angeles), and Bakersfield, California, during the California Research at the Nexus of Air Quality and Climate Change 2010. To the authors' knowledge, this work represents the most detailed characterization of the UCM in atmospheric samples to date. Knowledge of molecular structures, including carbon number, alkyl branching, and number of rings, provides important constraints on the rate of atmospheric processing, as the relative amounts of branched and linear alkanes are shown to be a function of integrated exposure to hydroxyl radicals. Emissions of semivolatile branched alkanes from fossil fuel‐related sources are up to an order of magnitude higher than those of linear alkanes, and the gas‐phase OH rate constants of branched alkanes are ~30% higher than their linear isomers. Based on a box model considering gas/particle partitioning, emissions, and reaction rates, semivolatile branched alkanes are expected to play a more important role than linear alkanes in the photooxidation of the UCM and subsequent transformations into SOA. Detailed speciation of semivolatile compounds therefore provides essential understanding of SOA sources and formation processes in urban areas.

Sources and Processes Contributing to Nitrogen Deposition: An Adjoint Model Analysis Applied to Biodiversity Hotspots Worldwide

Anthropogenic enrichment of reactive nitrogen (Nr) deposition is an ecological concern. We use the adjoint of a global 3-D chemical transport model (GEOS-Chem) to identify the sources and processes that control Nr deposition to an ensemble of biodiversity hotspots worldwide and two U.S. national parks (Cuyahoga and Rocky Mountain). We find that anthropogenic sources dominate deposition at all continental sites and are mainly regional (less than 1000 km) in origin. In Hawaii, Nr supply is controlled by oceanic emissions of ammonia (50%) and anthropogenic sources (50%), with important contributions from Asia and North America. Nr deposition is also sensitive in complicated ways to emissions of SO2, which affect Nr gas-aerosol partitioning, and of volatile organic compounds (VOCs), which affect oxidant concentrations and produce organic nitrate reservoirs. For example, VOC emissions generally inhibit deposition of locally emitted NOx but significantly increase Nr deposition downwind. However, in polluted boreal regions, anthropogenic VOC emissions can promote Nr deposition in winter. Uncertainties in chemical rate constants for OH + NO2 and NO2 hydrolysis also complicate the determination of source-receptor relationships for polluted sites in winter. Application of our adjoint sensitivities to the representative concentration pathways (RCPs) scenarios for 2010-2050 indicates that future decreases in Nr deposition due to NOx emission controls will be offset by concurrent increases in ammonia emissions from agriculture.

Tropospheric degradation of ethylene glycol monovinyl and divinyl ethers: A mechanistic and kinetic study

AbstractIn this work, we have performed a theoretical study on the mechanisms and kinetics of the •OH initiated oxidation of selected ethylene glycol vinyl ethers, using quantum chemistry and computational kinetics methods. We have found that the main reaction path is the •OH‐addition to vinyl double bonds, and especially to the vinyl terminal carbon atom. Branching ratios for addition at C1 are larger than 94%. Although divinyl ethers could be expected to react approximately twice as fast as monovinyl ethers, it was found that, in fact, •OH rate constants of monovinyl and divinyl ethers are very similar, in agreement with experimental results. This effect is attributed to the sharing of the oxygen lone pairs effect, when the molecule contains two vinyl groups. Thus, in EGMVE, the vinyl group is more reactive than the one in divinyl ethers. The energy of its highest occupied molecular orbital (HOMO) is closer to that of the OH radical, thus favoring the interaction with the single occupied molecular orbital (SOMO) of the radical. Negative activation enthalpies are obtained for the three molecules studied, implying that the rate constant decreases as temperature increases. This anti‐Arrhenius behavior is commonly observed in •OH addition to alkenes. An excellent correlation is observed between experimental and calculated rate constants. © 2012 Wiley Periodicals, Inc.

Atmospheric and kinetic studies of OH and HO 2 by the FAGE technique

Abstract A new FAGE setup has recently been built at the University of Lille, France. It permits the quantification of OH and HO 2 in the atmosphere with a detection limit of 3×10 5 molecules/(cm 3·min) for OH and 1×10 6 molecules/(cm 3·min) for HO 2. Its coupling to a photolysis cell enables the measurement of the total reactivity of the hydroxyl radical in ambient air and kinetic studies in laboratory. Two configurations have been considered: one with the photolysis cell at 90° to the FAGE nozzle, the other on line with the FAGE nozzle. The two configurations have been tested and validated by measuring the well known rate constants of OH with CH 4, C 3H 8 and CO. The advantages and drawbacks of each configuration have been evaluated. The “on line” configuration limits losses and permits measurements over a larger reactivity range but is affected by OH formation from the laser beam striking the FAGE nozzle, thus limiting the ability to carry out energy dependence studies which can, in contrast, be successfully performed in the 90° configuration.

Kinetics and mechanism of the reaction of OH with the trimethylbenzenes – experimental evidence for the formation of adduct isomers

The reversible gas-phase addition of OH radicals to the trimethylbenzenes was investigated in pulsed experiments utilizing VUV flash-photolysis resonance-fluorescence of H(2)O in the temperature range of 275-340 K. Triexponential OH decays were observed in the presence of the trimethylbenzenes, indicating the participation of more than one adduct species. Analytical solutions for the system of differential equations with two adduct isomers were derived, and the OH decay curves were evaluated based on this reaction model. This led to significant improvements of fit qualities and notable changes in OH rate constants compared to a previous model with a single adduct species. The detailed analysis was confined to 1,3,5-trimethylbenzene where reversible formation of two OH-aromatic ortho- and ipso-adduct isomers is feasible in accordance with the extended reaction model. Only after inclusion of additional isomerization reactions, consistent thermochemical data were obtained from the fitted rate constants. Reaction enthalpies of -83 ± 7 kJ mol(-1) and -35 ± 22 kJ mol(-1) were derived for the formation of one adduct isomer and the isomerization into the other, respectively. Based on literature data, the more and less stable adducts were assigned to ipso- and ortho-adduct isomers, respectively. The potential isomerization precluded the determination of primary yields of adduct isomers but formation of the ipso-adduct in any case is a minor process. For the rate constants of the OH + 1,3,5-trimethylbenzene reaction an Arrhenius expression k(OH) = 1.32 × 10(-11) cm(3) s(-1) exp(450 ± 50 K/T) was obtained. Based on the same approach, the rate constants of the OH reactions with 1,2,3-trimethylbenzene and 1,2,4-trimethylbenzene were derived as k(OH) = 3.61 × 10(-12) cm(3) s(-1) exp(620 ± 80 K/T) and k(OH) = 2.73 × 10(-12) cm(3) s(-1) exp(730 ± 70 K/T), respectively.

Cross sections and rate constants for OH + H2 reaction on three different potential energy surfaces for ro-vibrationally excited reagents

A systematic study of the reagent ro-vibrational excitations in H(2) + OH reaction is presented on three different potential energy surfaces using the multiconfiguration time-dependent Hartree method. An exact form of the kinetic energy operator including Coriolis coupling has been used. Coupled channel results on WDSE surface for vibrational excitation of H(2) produce very large cross sections in accordance with the previous approximate results. The rate constant obtained for H(2)(v = 1) at 300 K on the YZCL2 surface shows an excellent agreement with the most recent experimental result. Quantum dynamical results for ro-vibrational excitation of reagents obtained on the WSLFH surface show similar behavior to previous quasiclassical trajectory studies. The integral cross sections obtained for excited reagent rotations exhibit contrasting trends on the three surfaces. The effects are explained considering the different orientations of the transition state structure and the individual surface characteristics.