O2 Cathode Research Articles

Diversifying Ion-Transport Pathways of Composite Solid Electrolytes for High-Performance Solid-State Lithium-Metal Batteries.

The application of composite solid electrolytes (CSEs) in solid-state lithium-metal batteries is limited by the unsatisfactory ionic conductivity underpinned by the low concentration of free lithium ions. Herein, we propose an interface design strategy where an amine silane linker is employed as a coupling agent to graft the Li7La3Zr2O12 (LLZO) ceramic nanofibers to the poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) polymer matrix to enhance their interaction. The hydrogen bonding between amino-functionalized LLZO (NH2@LLZO) and PVDF-HFP not only effectively induces a uniform incorporation of high-content nanofibers (50 wt %) into the polymer matrix but also furnishes sufficient continuous surfaces to weaken the complexation between PVDF-HFP and Li-ion carriers. Additionally, introduction of the hydrogen bond and Lewis acid-base interplay strengthens the interfacial interactions between NH2@LLZO and lithium salts that release more free lithium ions for efficient interfacial transport. The impact of the linker's structure on the dissociation capacity of lithium salts is systematically studied from the steric effect perspective, which affords insights into interface design. Conclusively, the composite solid electrolyte achieves a high ionic conductivity (5.8 × 10-4 S cm-1) by synergy of multiple transport channels at ceramic, polymer, and their interface, which effectively regulates the lithium deposition behavior in symmetric cells. The excellent compatibility of the electrolyte with both LiFePO4 and LiNi0.8Co0.1Mn0.1O2 cathodes also results in a long lifetime and a high rate capability for full cells.

Precycling Strategy in Suitable Voltage to Improve the Stability of Interfacial Film and Suppress the Decline of LiNi0.6Mn0.2Co0.2O2 Cathode at Elevated Temperatures.

Layered ternary oxide LiNixMnyCo1-x-yO2 is a promising cathode candidate for high-energy lithium-ion batteries (LIBs). However, the capacity of LIBs is significantly restricted by several factors, including the repeated dissolution-regeneration of the interfacial film at high temperatures, the dissolution of transition metals, and the increase of impedance. Herein, a new precycling strategy in suitable voltage scope at room temperature is proposed to construct a uniform, thermally stable, and insoluble cathode-electrolyte interface (CEI), which helps to maintain stable cycling performances at high temperatures. Specifically, after 5 precycles in the range of 3.85-4.3 V at room temperature, a CEI layer containing numerous inorganic components and oligomers is formed on the surface of LiNi0.6Mn0.2Co0.2O2. Subsequently, the harmful side reactions are effectively suppressed, endowing the cell with an excellent capacity retention of 84.67% after 50 cycles at 0.5C and 55 °C, much higher than that of 65.61% under the conventional film-forming process conditions. This work emphasizes the crucial role of the precycling strategy in regulating the characteristics of CEI layer on the surface of cathode electrode, opening up a new avenue for the high-temperature application of positive electrodes of LIBs.

Recyclable Fluorine‐Free Water‐Borne Binders for High‐Energy Lithium‐Ion Battery Cathodes

AbstractThe rapidly increasing demand for lithium‐ion batteries and the fight against climate change call for novel materials that enhance performance, enable eco‐friendly processing, and are designed for efficient recycling. In lithium‐ion batteries, the binder polymer, used for cathode production, constitutes an integral but often overlooked component. The currently used polyvinylidene fluoride is processed with toxic organic solvents and has numerous other disadvantages concerning adhesion, conductivity, and recyclability. A change to aqueous processing using new, multi‐functional, purpose‐built materials that are soluble in water and fluorine‐free would thus constitute an important advance in the battery sector. Herein, four water‐soluble surfactant‐like polymers based on 11‐aminoundecanoic acid, that can be obtained in high purity and at a multigram scale are described. Free radical polymerization allows modification of the polymer with a wide variety of comonomers. The materials presented significantly enhance adhesion, are thermally stable at temperatures up to 350 °C, and are compatible with state‐of‐the‐art high‐energy LiNi0.6Mn0.2Co0.2O2 (NMC 622) cathode materials. It is also shown new recycling pathways made possible by the reversible pH‐dependent water‐solubility of the materials.

High loading electrode with superior electron/ion transport network for high performance lithium-ion batteries

High loading electrode design is beneficial to increase the energy density of lithium ion batteries. Two obstacles for the high loading electrode application should be removed, including the limitation on ion/electron transport within high loading electrode and the structure stability. Here, the electron conduction on LiNi0.8Co0.1Mn0.1O2 cathodes is enhanced with evenly and tightly Ketjen Black coating via high-speed dry mixing, while carbon nanotube is added to enhance the electron conduction between LiNi0.8Co0.1Mn0.1O2 particles, thus to construct three-dimensional electron migration channel. In addition, the large amount of electrolyte adsorbed by porous Ketjen Black and carbon nanotube enhances the Li+ ion diffusivity in this network. As a result, LiNi0.8Co0.1Mn0.1O2 electrode with only 1 % Ketjen Black and 3 % carbon nanotube can achieve both high electron/Li+ ion diffusivity and high parking density (2.2 g cm−3). A thick electrode with an areal mass loading of 20 mg cm−2 shows a high specific capacity of 111.2 mA h g−1 at 4 C and capacity retention rate of 98.2 % after 100 cycles at 2 C.

Stabilizing High-Voltage Performance of Nickel-Rich Cathodes via Facile Solvothermally Synthesized Niobium-Doped Strontium Titanate.

Ni-rich layered ternary cathodes are promising candidates thanks to their low toxic Co-content and high energy density (∼800 Wh/kg). However, a critical challenge in developing Ni-rich cathodes is to improve cyclic stability, especially under high voltage (>4.3 V), which directly affects the performance and lifespan of the battery. In this study, niobium-doped strontium titanate (Nb-STO) is successfully synthesized via a facile solvothermal method and used as a surface modification layer onto the LiNi0.8Co0.1Mn0.1O2 (NCM811) cathode. The results exhibited that the Nb-STO modification significantly improved the cycling stability of the cathode material even under high-voltage (4.5 V) operational conditions. In particular, the best sample in our work could provide a high discharge capacity of ∼190 mAh/g after 100 cycles under 1 C with capacity retention over 84% in the voltage range of 3.0-4.5 V, superior to the pristine NCM811 (∼61%) and pure STO modified STO-811-600 (∼76%) samples under the same conditions. The improved electrochemical performance and stability of NCM811 under high voltage should be attributed to not only preventing the dissolution of the transition metals, further reducing the electrolyte's degradation by the end of charge, but also alleviating the internal resistance growth from uncontrollable cathode-electrolyte interface (CEI) evolution. These findings suggest that the as-synthesized STO with an optimized Nb-doping ratio could be a promising candidate for stabilizing Ni-rich cathode materials to facilitate the widespread commercialization of Ni-rich cathodes in modern LIBs.

Constructing sulfur-rich interphase to promote the cycle stability of graphite/LiNi0.8Co0.1Mn0.1O2 pouch battery at elevated temperature

Lithium-ion batteries (LIBs) with LiNi0.8Co0.1Mn0.1O2 (NCM811) cathodes have a high energy density, but their long-cycle performance, especially at high temperature, should still be improved due to the instability of the NCM811 cathode-electrolyte interphase. In this work, 2, 2, 2-Trifluoroethyl p-Toluenesulfonate (TPTS) is introduced as a functional film-forming electrolyte additive design to improve the long-term stability of graphite/NCM811 batteries. The preferential redox reactions of TPTS molecules play a pivotal role in fostering the creation of a sulfur-riched interphase, characterized by low impedance. This interphase works to fortify the interfacial structure, effectively inhibiting the dissolution of transition metal ions. Therefore, in comparison to the graphite/NCM811 pouch batteries lacking additive, TPTS enhance the long-cycle capacity retention from 47 % to 80 % after 450 cycles at 45 °C. What's more, TPTS suppresses outgassing and demonstrates enhanced capacity maintenance for the battery even after storage at 60 °C. This work not only demonstrates the stabilizing impacts of TPTS on the electrode-electrolyte interphase and its enhancement of cycling performance at elevated temperatures but also introduces a novel approach for the practical utilization of functional electrolytes matching high-nickel LIBs.

High stability of Cu-doped O3-type NaNi1/3Fe1/3Mn1/3O2 cathode material for sodium-ion battery

High stability of Cu-doped O3-type NaNi1/3Fe1/3Mn1/3O2 cathode material for sodium-ion battery

Single-Crystal P2-Na0.67Mn0.67Ni0.33O2 Cathode Material with Improved Cycling Stability for Sodium-Ion Batteries.

Layered oxides constitute one of the most promising cathode materials classes for large-scale sodium-ion batteries because of their high specific capacity, scalable synthesis, and low cost. However, their practical use is limited by their low energy density, physicochemical instability, and poor cycling stability. Aiming to mitigate these shortcomings, in this work, we synthesized polycrystalline (PC) and single-crystal (SC) P2-type Na0.67-δMn0.67Ni0.33O2 (NMNO) cathode materials through a solid-state route and evaluated their physicochemical and electrochemical performance. The SC-NMNO cathode with a large mean primary particle size (D50) of 12.7 μm was found to exhibit high cycling stability leading to 47% higher capacity retention than PC-NMNO after 175 cycles at 1C rate in the potential window 4.2-1.5 V. This could be attributed to the effective mitigation of parasitic side reactions at the electrode-electrolyte interface and suppressed intergranular cracking induced by anisotropic volume changes. This is confirmed by the lower volume variation of SC-NMNO (ΔV ∼ 1.0%) compared to PC-NMNO (ΔV ∼ 1.4%) upon charging to 4.2 V. Additionally, the SC-NMNO cathode displayed slightly higher thermal stability compared to PC-NMNO. Both cathodes exhibited good chemical stability against air and water exposure, thus enabling material storage/handling in the ambient atmosphere as well as making them suitable for aqueous processing. In this regard, PC-NMNO was investigated with two low-cost aqueous binders, carboxymethyl cellulose, and sodium trimetaphosphate, which exhibited higher binding strength and displayed excellent electrochemical performance compared to PVDF, which could potentially lead to significant cost reduction in electrode manufacturing.

Revealing the origin of enhanced structural stability for nickel-rich LiNi0.83Co0.11Mn0.06O2 cathodes in situ modified with multifunctional polysiloxane

Multifunctional polysiloxane (MPS) layer is elaborately constructed on the surface of LiNi0.83Co0.11Mn0.06O2 (NCM83) particles via in situ hydrolysis-polycondensation of tetraethyl orthosilicate. Impressively, optimal NCM83 (NCM83-2) electrode covered with average 7 nm-thickness of fresh MPS layer delivers improved capacity retention ratio of 81.8 % after 150 cycles at 25 °C and retains the value of 78.7 % after 200 cycles at 60 °C and 1.0 C. Moreover, NCM83-2 electrode presents lower polarization degree with sluggish growth of the capacity platform. The significant advantages of NCM83-2 can be interpreted by the fact that the MPS layer effectively mitigates microcracks generation by inhibiting phase transition and lattice oxygen loss. Moreover, the MPS protective layer suppresses the thickening of cathode electrolyte interphase film and boosts the structural stability of NCM83 electrode to optimize electrochemical properties. Therefore, this strategy may provide promising enlightenments for preserving structural integrity and improving interfacial stability of nickel-rich cathodes for lithium-ion batteries.

Understanding the Effects of Bi Modification on the Properties of Ni‐rich Cathodes

AbstractWith the skyrocketing market demands for energy storage, lithium ions batteries (LIB) with higher energy density are urgently needed. Cathodes play a critical role in determining the energy density of LIB, and the most popular one is Ni‐rich cathode due to its high capacity. However, due to the fast structural degradation, Ni‐rich cathode materials should be further modified to achieve higher stability. Herein, we introduce bismuth ions in LiNi0.83Co0.11Mn0.06O2 cathodes by adding Bi2O3 during sintering to optimize the specific capacity and cycle stability. By adding 0.1 % mol Bi, the Li+ diffusion and structural stability are effectively optimized, leading to improved electrochemical performances. The modified sample delivers much higher specific capacity (222.9 mAhg−1, 0.05 C) than unmodified sample (204 mAhg−1, 0.05 C). Meanwhile, the specific capacity of optimized sample after 100 cycles at 0.33 C is 27.75 mAhg−1 higher than that of unmodified sample. Therefore, this work demonstrates that Bi modification can be regarded as a possible solution to optimizing the electrochemical performance of Ni‐rich cathodes.

Effect of Subtle Changes in Ni2+/Ni3+ and Particle Surface Area in LiNi0.5Mn0.5-xCoxO2 (x = 0.1 - 0.3) Cathode Materials for Lithium-Ion Batteries

Abstract In Li[Ni,Mn,Co]O2 (NMC) cathode materials, small changes in transition metal ratio and particle surface area can significantly impact capacity retention. To understand the combined effect of transition metal ratio and the particle surface area, we studied LiNi0.5Mn0.5-xCoxO2 (x = 0.1-0.3) particles with two different morphologies: dense, spherical particles and high-surface area aggregates. All compositions in this series contain the same percentage of Ni but have differing amounts of Ni2+ and Ni3+. While Ni2+ tends to induce anti-site defects predominantly in the bulk, Ni3+ promotes particle surface reconstruction, both of which negatively impact capacity retention. Upon cycling to 4.4 V for 100 cycles, we observe that particles of high surface area with high Ni3+ concentration undergo the most severe capacity degradation. However, high surface area particles with high proportion of anti-site defects undergo sluggish capacity fade. Overall, with 60% of Ni2+ and 40% of Ni3+, spherical NMC 532 particles endure the detrimental effects of anti-site defects and surface reconstruction, but neither too prominently and thus emerges as the best candidate among the studied samples. This study highlights the synergy between transition metal ratio and particle surface area and how it determines the properties of the NMC cathode materials.

Effects of Ti4+ doping on electrochemical properties of LiNi0.815Co0.15Al0.035O2 cathode materials

The high nickel ternary cathode materials LiNi0.815Co0.15Al0.035O2 (NCA) have been widely used in Li-ion batteries due to their high energy density, low cost, and little environmental pollution. However, it suffers from rapid capacity degradation and poor charging rate. In this work, Ti4+ doping NCA cathode materials are prepared by the high-temperature solid-state method. The results show that 0.5%Ti-NCA has a lower cationic mixing degree and better cycling performance. The capacity retention rate of 100 cycles is 98.91% and 96.59% at current densities of 0.5 C and 1.0 C, respectively. The CV and EIS test results show that 0.5%Ti-NCA has lower polarization and higher lithium ion diffusion coefficient DLi+(8.43×10−14 cm2/S) after 100 cycles, while Pure-NCA only has 6.92×10−15 cm2/S, which effectively enhances the electrochemical properties of NCA cathode materials.

Fusion Bonding Technique for Solvent-free Fabrication of All-solid-state Battery with Ultra-thin Sulfide Electrolyte.

For preparing next-generation sulfide all-solid-state batteries (ASSBs), the solvent-free manufacturing process have huge potential for the advantages of economic, thick electrode, and avoidance of organic solvents. However, the dominating solvent-free process is based on the fibrillation of polytetrafluoroethylene, suffering from poor mechanical property and electrochemical instability. Herein, a continuously solvent-free paradigm of fusion bonding technique is developed. A percolation network of thermoplastic polyamide (TPA) binder with low viscosity in viscous state is constructed with Li6PS5Cl (LPSC) by thermocompression (≤5MPa), facilitating the formation of ultrathin LPSC film (≤25μm). This composite sulfide film (CSF) exhibits excellent mechanical properties, ionic conductivity (2.1 mS/cm), and unique stress-dissipation to promote interface stabilization. Thick LiNi0.83Co0.11Mn0.06O2 cathode can be prepared by this solvent-free method and tighly adhered to CSF by interfacial fusion of TPA for integrated battery. This integrated ASSB shows high-energy-density feasibility (>2.5 mAh·cm-2 after 1400 cycles of 9200 hours and run for more than 10 000 hours), and energy density of 390 Wh·kg-1 and 1020 Wh·L-1. More specially, high-voltage bipolar cell (≥8.5V) and bulk-type pouch cell (326 Wh·kg-1) are facilely assembled with good cycling performance. This work inspires commercialization of ASSBs by a solvent-free method and provides beneficial guiding for stable batteries. This article is protected by copyright. All rights reserved.

Composition and state prediction of lithium-ion cathode via convolutional neural network trained on scanning electron microscopy images

High-throughput materials research is strongly required to accelerate the development of safe and high energy-density lithium-ion battery (LIB) applicable to electric vehicle and energy storage system. The artificial intelligence, including machine learning with neural networks such as Boltzmann neural networks and convolutional neural networks (CNN), is a powerful tool to explore next-generation electrode materials and functional additives. In this paper, we develop a prediction model that classifies the major composition (e.g., 333, 523, 622, and 811) and different states (e.g., pristine, pre-cycled, and 100 times cycled) of various Li(Ni, Co, Mn)O2 (NCM) cathodes via CNN trained on scanning electron microscopy (SEM) images. Based on those results, our trained CNN model shows a high accuracy of 99.6% where the number of test set is 3840. In addition, the model can be applied to the case of untrained SEM data of NCM cathodes with functional electrolyte additives.

Synthesis and Characterization of Na2/3[Fe1/2Mn1/2]O2 Cathode Material for Sodium Ion Batteries

<p><strong>Abstract. </strong>Recently,<strong> </strong>Na<sub>2/3</sub>[Fe<sub>1/2</sub>Mn<sub>1/2</sub>]O<sub>2</sub> has received attention as a potential candidate material for cathode sodium-ion batteries. However, this material was synthesized by a solid-state process, resulting in larger particle size and nonuniform morphology. The larger particle size will sluggish the Na ion diffusion. Here we report the synthesis of Na<sub>2/3</sub>[Fe<sub>1/2</sub>Mn<sub>1/2</sub>]O<sub>2</sub> using a simple sol-gel process. The X-ray diffraction revealed that the sample was identified as Na<sub>2/3</sub>[Fe<sub>1/2</sub>Mn<sub>1/2</sub>]O<sub>2</sub> with a hexagonal crystal structure. However, the impurities are formed at diffraction angles of 36.28°, 45.03°, and 51.23°. Calcination temperature affects the formation of the crystal phase, grain growth, morphology, and particle size. Our findings provide valuable insight into the development of Na<sub>2/3</sub>[Fe<sub>1/2</sub>Mn<sub>1/2</sub>]O<sub>2</sub>  material with desirable properties.</p><p> </p><p><strong>Keywords:</strong></p><p>Sol-Gel, Solid State, Grain Growth, Calcination, Na<sub>2/3</sub>[Fe<sub>1/2</sub>Mn<sub>1/2</sub>]O<sub>2</sub></p><p> </p>

Enhancing Structural Rigidity of Ultrahigh-Ni Oxide Through Al and Nb Dual-Bulk-Doping for High-Voltage Lithium-Ion Batteries.

The pursuit of high energy densities propels the design of next-generation nickel-based layered oxide cathodes. The utilization of low-cobalt, ultrahigh-nickel layered oxide cathodes, and the extension of operating voltages promise enhanced energy density. However, stability and safety face challenges associated with nickel content, including structural degradation, lattice oxygen evolution, and thermal instability. In this study, a promising strategy of Al and Nb dual-bulk-doping is presented in high-Ni cathode materials of LiNi0.96Co0.04O2 (NC) to stabilize the bulk structure, suppress oxygen release, and attain superior electrochemical performance at high voltages. The introduction of Al and Nb effectively raises the migration energy of Ni2+ into Li sites and stabilizes lattice oxygen through strengthened Al─O and Nb─O bonds. Furthermore, the substitution of high-valence Nb ions reduces the charge depletion of lattice oxygen and induces an ordered microstructure. The Al and Nb dual-bulk-doping strategy mitigates strain and stress associated with the H2↔H3 phase transition, reducing the generation and propagation of microcracks. The resulting Li(Ni0.96Co0.04)0.985Al0.01Nb0.005O2 (NCAN) cathode exhibits superior cycling stability, with a capacity retention of 77.8% after 300 cycles, even when operating at a high-voltage of 4.4V, outperforming the NC (48.5%). This work provides a promising perspective for developing high-voltage and high-Ni cathode materials.

Revealing Dynamic Evolution of the Anode‐Electrolyte Interphase in All‐Solid‐State Batteries with Excellent Cyclability

AbstractAll‐solid‐state‐batteries (ASSBs) based on a halide solid electrolyte (SE) and a lithium‐metal based anode typically have poor cyclability without a buffer layer (such as Li3PS4 or Li6PS5Cl) to prevent the degradation reactions. Here excellent cycling stability of ASSB consisting of an uncoated single‐crystal LiNi0.8Co0.1Mn0.1O2 cathode and a Li3YCl6 (LYC) SE separator in direct contact with a Li‐In anode are demonstrated. Through a combination of electrochemical measurements, synchrotron micro‐X‐ray absorption and diffraction analyses, and density functional theory calculations, reveal for the first time that along with the standard Li+ transport during charge/discharge, indium in the Li‐In anode also participates in the redox reactions. The in‐situ generated In3+ preferentially occupies the vacant Li sites in the trigonal LYC lattice, leading to the formation, growth, and eventual stabilization of an anode‐electrolyte interphase (AEI) layer consisting of an In‐doped Li3‐xInxYCl6 (x = ≈0.2) phase. It is discussed how the presence of such an AEI layer prevents LYC decomposition and suppresses dendrite formation and propagation, enabling stable cycling of ASSB with ≈90% capacity retention over 1000 cycles. This work sheds light on the dynamic evolution of the halide SE and alloy anode interphase, and opens new avenues in the future design of long‐lasting high‐energy all‐solid‐state‐batteries.

Optimization of NMC Cathode Inks for Cost-Effective and Eco-Friendly Screen-Printed Lithium-Ion Batteries

Li-ion batteries are life-saving energy storage technology. However, the battery manufacturing process still needs complicated and expensive production lines because of the sensitive nature of active materials towards the open atmosphere. Additionally, employing hazardous N-Metil-2-Pirrolidon (NMP) solvents, which are also restricted by the World Health Organization for electrode preparation, contributes to unsafe working conditions. In this study, water-based LiNi0.8Mn0.1Co0.1O2 (NMC811) cathode inks were produced and printed by the screen-printing method, which is widely used in sensors and electronics fabrication due to its potential practical applications and low-cost production possibilities. Despite their suitability for operation at high voltage ranges, NMC811 cathodes typically exhibit rapid capacity drops over time because of side reactions and Cathode-Electrolyte Interphase (CEI) thickening. In this study, to overcome the capacity drop issue and make it possible to produce water-based cathode inks, NMC811 particles were encapsulated with reduced graphene oxide (rGO) via a hydrothermal method. Water-based Carboxymethyl cellulose (CMC) - Polyethylene oxide (PEO) binders are compared with conventional Polyvinylidene fluoride (PVDF)-NMP binders and exhibited promising electrochemical stability of 75% after 50 cycles within a high voltage range of 2.8-4.6 V. Therefore, the water-based novel cathode ink presented in this study is not only well-suited for advancing the development of printed batteries but also stride towards more eco-friendly processes thanks to replacing the toxic NMP with water. Moreover, battery printing technologies have also a strategic importance by reducing the investment cost of battery-producing.

Surface modification of rare earth elements to enhance the electrochemical stability of Ni-rich Co-free cathodes

The Ni-rich Co-free cathode materials are considered the most optimistic choice for the long-term economic development of lithium-ion batteries (LIBs) due to the limited supply and high prices of cobalt. In this study, a uniform samarium oxide (Sm2O3) layer was coated on the surface of LiNi0.8Mn0.17Fe0.03O2 (NMF) cathode materials through wet subsequent heat treatment. Compared with the unmodified cathode materials, the modified cathode materials exhibit better electrochemical performance at high voltage. The specific discharge capacity of the modified cathode materials increased from 37.5 mAh g−1 (NMF) to 118.2 mAh g−1 after 200 cycles at 1 C and the retention rate increased from 21.18% to 69.77%. The samarium oxide coating effectively inhibits the reaction between the cathode materials and the electrolyte. Therefore, our study proposes a simple and scalable method for modifying nickel-rich cobalt-free cathode materials.

Improving storage performance and lattice oxygen stability of single crystal LiNi0.925Co0.03Mn0.045O2 by integrating utilization of surface residual lithium and lattice modulation

In lithium-ion batteries, Ni-rich single crystal cathode material (Ni > 90 %) is a promising cathode material, but it has not yet been put into commercial application due to defects such as structural degradation, air sensitivity and thermal instability. In this paper, the residual lithium compounds on the surface of high-nickel materials are not useless. Li3PO4 coated and Mg2+ doped single crystal cathode materials (SC-NCM-MP) were successfully prepared by precisely controlling the amount of MgHPO4 by titration and reacting with lithium compounds left on the surface of LiNi0.925Co0.03Mn0.045O2 (SC-NCM) cathode materials. The SC-NCM-MP samples exhibit better lattice oxygen stability, Li-ion mobility, storage performance and electrochemical performance, with a retention of 89.36 % after 100 cycles, which is much higher than 79.78 % of SC-NCM.