Normal Concrete Substrate Research Articles

초속경 라텍스개질 콘크리트로 보강된 RC보의 비선형 휨해석

라텍스로 개질된 콘크리트는 높은 휨강도 뿐만아니라 부착강도 및 투수저항성이 좋은 재료특성을 제공한다. 이러한 이점을 활용한 초속경 라텍스개질 콘크리트(VES-LMC)에 관련된 연구결과는 재료에 관한 것이 대부분으로, VES-LMC로 덧씌우기 보강된 RC 보의 부착 경계면 거동특성에 대한 체계적인 연구는 미진하다. 따라서 본 논문에서는 VES-LMC로 보강된 철근콘크리트 보의 비선형 휨 거동에 대한 특성을 알아보고자 ABAQUS를 매개변수 연구를 수행한 결과 다음과 같은 결과를 얻을 수 있었다. 비선형 휨 해석을 위하여 본 논문에 적용된 모델의 적합성 여부를 확인한 결과 실험값과 비교적 유사한 경향을 보이는 것을 확인 할 수 있었다. 두께가 증가함에 따라 최대 저항강도가 증가하는 경향을 보여주었으며, 또한 강성 이 증가하여 내하력이 증진되는 결과를 확인할 수 있었다. 부착강도를 변수로 해석한 결과, 전단강도가 증가함에 따라 휨 저항능력이 향상되는 결과를 확인 하였으며, 두 이질재료의 부착능력이 구조물의 내하력에 지배적인 인자로 작용하는 것을 알 수 있었다. Latex modification of concrete provides the material with higher flexural strength, as well as high bond strength and reduced water permeability. One of the most advantages of the very early-strength latex-modified concrete (VES-LMC) could be the similar contraction and expansion behaviour to normal concrete substrate, which enable to ensure long-term performance. The purpose of this study was to parametric nonlinear flexural nonlinear analysis of RC beam rehabilitated by VES-LMC. The results were as follows; The flexural nonlinear analysis model of RC beam overlaid by VES-LMC in ABAQUS was proposed to predict the load-deflection response, interfacial stress, and ultimate strength. The proposed FE analysis model was verified by comparison of an experimental data and the FE analysis results. The FE analysis results showed that yield point as well as flexural stiffness increased as the depth increased; the stiffness of beam overall increased as the bond stiffness became larger; the bond strength between two different materials is a key factor in composite beam. A parametric study showed that an overlay thickness was a main influencing factor to the behavior of RC beam overlaid by VES-LMC.

Interface evaluations of overlay-concrete bi-layer composites by a direct shear test method

Abstract Interface evaluations of four high-performance concrete overlays cast on top of one type of normal concrete substrate were made by a new direct shear test method. Two different surface preparations such as mechanical abrasion and chemical etching were followed to manufacture 64 overlay–substrate bi-layer specimens. This paper discusses the material properties and fabrication and evaluations of bi-layer specimens. Results show that successful interface bond characterization was possible through this direct shear apparatus. The test method seems to be suitable for screening and selection of various overlays for their compatibility with substrate concrete. However, some modification in the tool is needed for assessing the high-bond capacity interface. Effects of bonding slurry also needs further study.