Non-fullerene Acceptors Research Articles

Sensitive SWIR Organic Photodetectors with Spectral Response Reaching 1.5µm.

The performance of organic photodetectors (OPDs) sensitive to the short-wavelength infrared (SWIR) light lags behind commercial indium gallium arsenide (InGaAs) photodetectors primarily due to the scarcity of organic semiconductors with efficient photoelectric responses exceeding 1.3µm. Limited by the Energy-gap law, ultralow-bandgap organic semiconductors usually suffer from severe non-radiative transitions, resulting in low external quantum efficiency (EQE). Herein, a difluoro-substituted quinoid terminal group (QC-2F) with exceptionally strong electron-negativity is developed for constructing a new non-fullerene acceptor (NFA), Y-QC4F with an ultralow bandgap of 0.83eV. This subtle structural modification significantly enhances intermolecular packing order and density, enabling an absorption onset up to 1.5µm while suppressing non-radiation recombination in Y-QC4F films. SWIR OPDs based on Y-QC4F achieve an impressive detectivity (D*) over 1011 Jones from 0.4 to 1.5µm under 0V bias, with a maximum of 1.68 × 1012 Jones at 1.16µm. Furthermore, the resulting OPDs demonstrate competitive performance with commercial photodetectors for high-quality SWIR imaging even under 1.4µm irradiation.

Constructing Multiscale Fibrous Morphology to Achieve 20% Efficiency Organic Solar Cells by Mixing High and Low Molecular Weight D18.

This study underscores the significance of precisely manipulating the morphology of the active layer in organic solar cells (OSCs). By blending polymer donors of D18 with varying molecular weights, a multiscale interpenetrating fiber network structure within the active layer is successfully created. The introduction of 10% low molecular weight D18 (LW-D18) into high molecular weight D18 (HW-D18) produces MIX-D18, which exhibits an extended exciton diffusion distance and orderly molecular stacking. Devices utilizing MIX-D18 demonstrate superior electron and hole transport, improves exciton dissociation, enhances charge collection efficiency, and reduces trap-assisted recombination compared to the other two materials. Through the use of the nonfullerene acceptor L8-BO, a remarkable power conversion efficiency (PCE) of 20.0% is achieved. This methodology, which integrates the favorable attributes of high and low molecular weight polymers, opens a new avenue for enhancing the performance of OSCs.

Constraining the Excessive Aggregation of Non-Fullerene Acceptor Molecules Enables Organic Solar Modules with the Efficiency >16.

Translating high-performance organic solar cell (OSC) materials from spin-coating to scalable processing is imperative for advancing organic photovoltaics. For bridging the gap between laboratory research and industrialization, it is essential to understand the structural formation dynamics within the photoactive layer during printing processes. In this study, two typical printing-compatible solvents in the doctor-blading process are employed to explore the intricate mechanisms governing the thin-film formation in the state-of-the-art photovoltaic system PM6:L8-BO. Our findings highlight the synergistic influence of both the donor polymer PM6 and the solvent with a high boiling point on the structural dynamics of L8-BO within the photoactive layer, significantly influencing its morphological properties. The optimized processing strategy effectively suppresses the excessive aggregation of L8-BO during the slow drying process in doctor-blading, enhancing thin-film crystallization with preferential molecular orientation. These improvements facilitate more efficient charge transport, suppress thin-film defects and charge recombination, and finally enhance the upscaling potential. Consequently, the optimized PM6:L8-BO OSCs demonstrate power conversion efficiencies of 18.42% in small-area devices (0.064 cm2) and 16.02% in modules (11.70 cm2), respectively. Overall, this research provides valuable insights into the interplay among thin-film formation kinetics, structure dynamics, and device performance in scalable processing.

A theoretical study on symmetrical non-fullerene electron acceptors molecules on BDTPT based derivatives to enhance photovoltaic properties of organic solar cells

An innovative and promising approach to developing sustainable energy solutions and promoting an eco-friendly society is the use of organic solar cells. The key component for a solution-processed bulk-heterojunction organic solar cell is the photoactive layer’s embedded donor and acceptor components. This research presents seven modified molecules comprising the A–D–A type structural configuration, entitled A1–A7. All these designed moieties exhibit marvelous outcomes in optoelectronic features, including λmax and band gap, owing to non-fullerene acceptors in the terminal regions. All these compounds are computationally assessed by employing B3LYP at 6-31G (d,p) basis set using chloroform solvent. Compared to the reference molecule, the designed molecules (A1, A2, A4, A5, A6, A7) have reflected breakthrough results. The prerequisite for directing the practical application of designed acceptors is the efficient charge transfer, evidenced by coupling the J61 donor complex with the designed A5 acceptor.

Investigation of fullerene and non-fullerene materials in organic photocatalysts on the efficiency of photocatalytic degradation of polychlorinated biphenyls

The photocatalytic degradation of polychlorinated biphenyls (PCBs) is advancing, yet the efficiency of degradation within the visible spectral range continues to encounter significant challenges. In this study, two biochar-based organic semiconductor photocatalysts, Active Carbon@PTQ10 (5,8-Dibromo-6,7-difluoro-2-(2-hexyldecoxy)quinoxaline; trimethyl-(5-trimethylstannylthiophen-2-yl)stannane): ITIC-Th (Propanedinitrile,2,2′-[[6,6,12,12-tetrakis(5-hexyl-2-thienyl)-6,12-dihydrodithieno[2,3-d: 2′,3′-d’] −s-indaceno[1,2-b:5,6-b’] dithiophene-2,8-diyl] bis[methylidyne(3-oxo-1H-indene-2,1(3H)-diylidene)]] bis-) (AC@PI) and Active Carbon@PTQ10: PC71BM (6,6)-phenyl C71 butyric acid methyl ester), were synthesized using a wide bandgap material, PTQ10, as the electron donor, along with a non-fullerene material, ITIC-Th, and a fullerene material, PC71BM, as the acceptors, respectively. Under optimized conditions, AC@PI degraded 93.4 % of 2,2 ’,4,4 ’-tetrachlorobiphenyl (PCB 47) within 60 min. By incorporating a non-fullerene acceptor (ITIC-Th), AC@PI exhibits a larger surface photopressure, a lower hole-electron transfer ratio, a broader absorption spectrum (400 – 1000 nm), and enhanced structural stability. AC@PI can generate photogenerated electrons and holes, as well as superoxide anions (O2−) and hydroxyl radicals (OH), through type II heterojunctions, which contributes to its exceptional properties. This study synthesized novel organic semiconductor catalysts that offer a green, efficient, and non-toxic method for the degradation of aromatic pollutants, such as polychlorinated biphenyls.

A Perspective on 2D Fused-Ring Quad-Rotor-Shaped Nonfullerene Acceptors with an Anthracene Core.

Previous studies have demonstrated the remarkable properties of quad-rotor-shaped two-dimensional nonfullerene acceptors (2D NFAs), which encompass exceptional electron affinity, robust sunlight absorption, effective exciton separation, and accelerated electron transfer capabilities. Naphthalene has been demonstrated to be a significant 2D fused core to construct high-performance 2D NFAs. However, synthesizing such materials through existing synthetic pathways poses a significant challenge. In this work, we designed four 2D NFAs (TEA-SIC, TEA-SIC-8F, TEA-SIC-OH, and TEA-SIC-OH-8F) with an anthracene core. These NFAs can theoretically be synthesized into a quad-rotor configuration through a seven-step synthetic process. Theoretical calculations have demonstrated that these 2D NFAs exhibit superior electron-accepting abilities, enhanced sunlight absorption, and more efficient exciton dissociation compared to Y6. Furthermore, TEA-SIC and TEA-SIC-8F exhibited impressive electron mobilities of 1.76 × 10-3 cm2 V-1 s-1 and 1.18 × 10-3 cm2 V-1 s-1, respectively, indicating their suitability for the development of high-performance organic solar cells (OSCs). Although TEA-SIC-OH and TEA-SIC-OH-8F have lower electron mobility, their high sunlight absorption and efficient exciton separation suggest potential as third components in ternary OSCs. These 2D NFAs also exhibit a commendable solubility in most alcohol-based solvents, indicating their potential for specialized applications in the fabrication of stacked OSCs. These findings provide valuable insights for the future design of synthesizable high-performance 2D NFAs.

Small-Molecule Mixed Ionic-Electronic Conductors for Efficient N-Type Electrochemical Transistors: Structure-Function Correlations.

The fundamental challenge in electron-transporting organic mixed ionic-electronic conductors (OMIECs) is simultaneous optimization of electron and ion transport. Beginning from Y6-type/U-shaped non-fullerene solar cell acceptors, we systematically synthesize and characterize molecular structures that address the aforementioned challenge, progressively introducing increasing numbers of oligoethyleneglycol (OEG; g) sidechains from 1g to 3g, affording OMIECs 1gY, 2gY, and 3gY, respectively. The crystal structure of 1gY preserves key structural features of the Yn series: a U-shaped/planar core, close π-π molecular stacking, and interlocked acceptor groups. Versus inactive Y6 and Y11, all of the new glycolated compounds exhibit mixed ion-electron transport in both conventional organic electrochemical transistor (cOECT) and vertical OECT (vOECT) architectures. Notably, 3gY with the highest OEG density achieves a high normalized transconductance of 25.29 S cm-1, an on/off current ratio of ~106, and a turn-on/off response time of 94.7/5.7 ms in vOECTs. Systematic optoelectronic, electrochemical, architectural, and crystallographic analysis explains the superior 3gY-based OECT performance in terms of denser ngY OEG content, increased crystallite dimensions with decreased long-range crystalline order, and enhanced film hydrophilicity which facilitates ion transport and efficient redox processes. Finally, we demonstrate an efficient small-molecule-based complementary inverter using 3gY vOECTs, showcasing the bioelectronic applicability of these new small-molecule OMIECs.

Optimizing non-fullerene acceptor molecules constituting fluorene core for enhanced performance in organic solar cells: a theoretical methodology.

Looking for novel outstanding performance materials suitable for organic solar cells, we constructed a range of non-fullerene acceptors (NFAs) evolved from the recently synthesized acceptor molecule identified as DICTIF, structured around fluorene core where 2-(2,3-dihydro-3-oxo-1H-inden-1-ylidene) propanedinitrile presented the terminals end-groups. Employing density functional theory (DFT) and time dependent-DFT (TD-DFT) simulations, we have simulated the impact of altering the end groups of DICTIF molecule by five assorted acceptors molecules, for the purpose of exploring their opto-electronic properties and their performance in organic solar cell (OSC) applications. We proved that the designed non-fullerene acceptors provide enhanced efficiency compared to the synthesized molecule, such as planar geometries and narrower energy gap ranging from 1.51 to 1.95 eV. A red shift in absorption was observed for all tailored molecules (λmax = 583.5-711.4 nm) as compared to the reference molecule (λmax = 578 nm).Various decisive factors such as frontier molecular orbitals (FMOs), exciton binding energy (EB), absorption maximum (λmax), open circuit voltage (VOC), reorganization energies (RE), transition density matrix (TDM), reduced density gradient (RDG), and electron-hole overlap have also been computed for analyzing the performance of NFAs. Low reorganizational energy values facilitate charge mobility which improves the conductivity of all the designed molecules. This study showed that our novel tailored molecules might be suitable candidates for the fabrication of highly efficient photovoltaic materials. After testing various hybrid functionals, optimized geometries were assigned using DFT HSEH1PBE/6-31G(d) level of theory. Electronic excitations and absorption spectra were investigated using the TD-DFT MPW1PW91/6-31G(d) level of theory. We ascertained that HSEH1PBE/6-31G(d) level of theory yield the closest calculated highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels of the DICTIF to the corresponding experimental ones and that TD-MPW1PW91//6-31G(d) was the most suitable level of theory for exploring electronic excitations and finding the maximum of absorption (λmax).

The effect of fluorinated conjugated side chains on the photovoltaic performance of polymers based on benzodithiophene (BDT) and carbazolobistriazole (CTA)

Reasonable regulation of the structure-performance relationship is extremely crucial to enhancing the device performance of organic solar cells (OSCs). As a novel fused-benzotriazole (BTA) electron-accepting (A) unit, carbazolobistriazole (CTA) has excellent luminescent properties, and the alkyl chains on the three N atoms allow flexible modulation of polymer solubility. However, higher molecular energy levels and weak crystallinity restrict the enhancement of device performance. Herein, a new donor polymer PE97 with CTA as A unit and 4,8-bis(4-(2-ethylhexyl)-3,5-difluorophenyl)benzo[1,2-b:4,5-b’]dithiophene (BDT-P2F) as electron-donating (D) unit was designed and synthesized. In comparison with the first CTA-based polymer PE93 with 4,8-bis(5-(2-ethylhexyl)-4-fluorothiophen-2-yl)benzo[1,2-b:4,5-b’]dithiophene (BDT-TF) as D unit, PE97 realizes stronger molecular stacking conducive to modulation of the active layer morphology and a deeper highest occupied molecular orbital (HOMO) level, which are favorable to increase short-circuit current density (JSC) and open-circuit voltage (VOC) of OSCs. When paired with Y-series non-fullerene acceptor eC9-2F, PE97-based OSC devices have achieved a higher power conversion efficiency (PCE) of 15.5 %, with a VOC of 0.81 V, a JSC of 25.3 mA cm−2, and a fill factor (FF) of 75.7 %, which figures significantly surpass efficiency (13.6 %) of PE93-based devices. These results indicate that the BDT-P2F unit can excellently modulate the optoelectronic properties of CTA-based polymers. This highlights the potential of the BDT-P2F as a promising D unit for polymers with weak crystallinity and limited electron-withdrawing properties.

Boosting the Efficiency of Perovskite/Organic Tandem Solar Cells via Enhanced Near-Infrared Absorption and Minimized Energy Losses.

The compatibility of perovskite and organic photovoltaic materials in solution processing provides a significant advantage in the fabrication of high-efficiency perovskite/organic tandem solar cells. However, additional recombination losses can occur during exciton dissociation in organic materials, leading to energy losses in the near-infrared region of tandem devices. Consequently, a ternary organic rear subcell is designed containing two narrow-bandgap non-fullerene acceptors to enhance the absorption of near-infrared light. Simultaneously, a unique diffusion-controlled growth technique is adopted to optimize the morphology of the ternary active layer, thereby improving exciton dissociation efficiency. This innovation not only broadens the absorption range of near-infrared light but also facilitates the generation and effective dissociation of excitons. Owing to these technological improvements, the power conversion efficiency (PCE) of organic solar cells increased to 19.2%. Furthermore, a wide-bandgap perovskite front subcell is integrated with a narrow-bandgap organic rear subcell to develop a perovskite/organic tandem solar cell. Owing to the reduction in near-infrared energy loss, the PCE of this tandem device significantly improved, reaching 24.5%.

Regulating Intermolecular Interactions and Film Formation Kinetics for Record Efficiency in Difluorobenzothiadizole-based Organic Solar Cells.

The difluorobenzothiadizole (ffBT) unit is one of the most classic electron-accepting building blocks used to construct D-A copolymers for applications in organic solar cells (OSCs). Historically, ffBT-based polymers have achieved record power conversion efficiencies (PCEs) in fullerene-based OSCs owing to their strong temperature-dependent aggregation (TDA) characteristics. However, their excessive miscibility and rapid aggregation kinetics during film formation have hindered their performance with state-of-the-art non-fullerene acceptors (NFAs). Herein, we synthesized two ffBT-based copolymers, PffBT-2T and PffBT-4T, incorporating different π-bridges to modulate intermolecular interactions and aggregation tendencies. Experimental and theoretical studies revealed that PffBT-4T exhibits reduced electrostatic potential differences and miscibility with L8-BO compared to PffBT-2T. This facilitates improved phase separation in the active layer, leading to enhanced molecular packing and optimized morphology. Moreover, PffBT-4T demonstrated a prolonged nucleation and crystal growth process, leading to enhanced molecular packing and optimized morphology. Consequently, PffBT-4T-based devices achieved a remarkable PCE of 17.5%, setting a new record for ffBT-based photovoltaic polymers. Our findings underscore the importance of conjugate backbone modulation in controlling aggregation behavior and film formation kinetics, providing valuable insights for the design of high-performance polymer donors in organic photovoltaics.

Photoinduced charge transfer in small-molecule organic solar cells dependent on external electric field

In this paper, MTDATA is selected as the electron donor and BPhen as the acceptor. The trianiline structure of the donor molecule provides a variety of charge transfer pathways for charge separation. Based on Marcus theory, the photoinduced charge transfer properties of non-fullerene acceptor organic solar cells (NFA-OSCs) in external electric field (Fext) were studied. By analyzing the changes of reorganization energy (λ), Gibbs free energy (ΔG), electron transfer integral (Vda) and charge transfer rate under the influence of Fext, it was found that Fext can effectively regulate the charge transfer. Moreover, the change of charge transfer rate under Fext is similar to Vda, indicating that Vda is the main factor affecting charge transfer rate. To a certain extent, this study provides theoretical support for improving the photoelectric performance of NFA-OSCs.

Enhancing Specific Detectivity and Device Stability in Vacuum-Deposited Organic Photodetectors Utilizing Nonfullerene Acceptors.

Organic photodetector (OPD) studies have undergone a revolutionary transformation by introducing nonfullerene acceptors (NFAs), which provide substantial benefits such as tunable band gaps and enhanced absorption in the visible spectrum. Vacuum-processed small-molecule-based OPD devices are presented in this study by utilizing a blend of boron subphthalocyanine (SubPc) and chlorinated subphthalocyanine (Cl6SubPc) as the active layer. Four different active layer thicknesses are further investigated to understand the intrinsic phenomena, unveiling the suppression of dark current density while maintaining photoexcitation and charge separation efficiency. Experimental results reveal that, at an applied bias of -3 V, the 50-nm-thick active layer achieves a remarkably low dark current density of 1.002 nA cm-2 alongside a high external quantum efficiency (EQE) of 52.932% and a responsivity of 0.226 A W-1. These impressive performance metrics lead to a specific detectivity of 1.263 × 1013 Jones. Furthermore, the findings offer new insights into intrinsic phenomena within the bulk heterojunction (BHJ), such as thermally generated current and exciton quenching. This integration is potentially well-heeled to revolutionize display technology by combining high-sensitivity photodetection, offering new possibilities for novel display panels with sensing applications.

Enhancing Efficiency and Stability of Inverted Perovskite Solar Cells through Solution-Processed and Structurally Ordered Fullerene.

The electron transporting layer (ETL) used in high performance inverted perovskite solar cells (PSCs) is typically composed of C60, which requires time-consuming and costly thermal evaporation deposition, posing a significant challenge for large-scale production. To address this challenge, herein, we present a novel design of solution-processible electron transporting material (ETM) by grafting a non-fullerene acceptor fragment onto C60. The synthesized BTPC60 exhibits an exceptional solution processability and well-organized molecular stacking pattern, enabling the formation of uniform and structurally ordered film with high electron mobility. When applied as ETL in inverted PSCs, BTPC60 not only exhibits excellent interfacial contact with the perovskite layer, resulting in enhanced electron extraction and transfer efficiency, but also effectively passivates the interfacial defects to suppress non-radiative recombination. Resultant BTPC60-based inverted PSCs deliver an impressive power conversion efficiency (PCE) of 25.3% and retain almost 90% of the initial values after aging at 85°C for 1500 hours in N2. More encouragingly, the solution-processed BTPC60 ETL demonstrates remarkable film thickness tolerance, and enables a high PCE up to 24.8% with the ETL thickness of 200 nm. Our results highlight BTPC60 as a promising solution-processed fullerene-based ETM, opening an avenue for improving the scalability of efficient and stable inverted PSCs.

High-performing organic/quantum dot hybrid upconversion device based on a single-component near-infrared-sensitive layer

A donor/acceptor (D/A) heterojunction with an interfacial energetic offset is demonstrated to enable efficient exciton dissociation in organic photodetectors and upconversion devices (UCDs). Unfortunately, this approach usually encounters complicated optimization procedures and interfacial instability. Herein, we present an alternative strategy for achieving high-performing UCDs by utilizing an organic single-component near-infrared (NIR)-sensitive layer instead of a D/A heterojunction. The showcased UCD is constructed by vertically stacking an organic single-component Y6 NIR-detection unit and a quantum dot light-emitting unit. Due to the high dielectric constant and low exciton binding energy of the non-fullerene acceptor Y6, free carriers are directly and spontaneously generated upon NIR light excitation. As a result, the single-component UCD achieves a low light detection capability of 2.5 μW/cm2, a fast refresh rate of >3.8 × 104, and a high resolution exceeding 1100 dpi, providing a stable optical response to high-frequency NIR signals and high-quality NIR imaging.

Advancements in optical and optoelectronic characteristics of benzotriazole-based asymmetric non-fullerene acceptors for organic photovoltaics

The development of energy-efficient non-fullerene acceptors (NFAs) has attracted much attention in producing efficient organic solar cells (OSCs). These innovative materials are considered a promising alternative to traditional fullerene acceptors because they absorb a broader light range and potentially enhance the OSC performance. Herein, we engineered eleven new asymmetric caterpillar-shaped materials with an A1-D-A2-A1 core as NFAs for OSCs. These efficient materials offer a high absorption efficiency, wide energy level range, and efficient charge transport capabilities. To engineer these caterpillar-shaped NFAs (FT1-FT11), we performed various synergistic modulations of end-capped electron-withdrawing moieties and side-chain engineering on the synthetic reference molecule (FT). The electron and hole reorganization energies, binding energy, transition energy, transition density analysis, electrostatic potential, and photovoltaic characterizations have been performed for these designed caterpillar-shaped (FT1–FT11) series. The designed materials (FT1–FT11) showed a lower binding energy of 0.45 eV, a narrower bandgap (2.11 eV), higher absorption (ranges from 700.44 nm to 781.05), and low electron and hole mobilities (0.0029 and 0.0031) compared to reference molecule FT. To investigate the charge transport process, we employed polymer donor PTB7-Th and efficient NFA acceptor FT11 to establish a donor:acceptor complex (FT11:PTB7-Th). The complex study demonstrates a significant charge transformation at the donor-acceptor interface. As a result, the developed compounds (FT1–FT11), with their superior optoelectronic capabilities, could be viewed as a viable and sustainable choice to fabricate next-generation efficient OSCs.

Frenkel and Charge-Transfer Excitonic Couplings Strengthened by Thiophene-Type Solvent Enables Binary Organic Solar Cells with 19.8 % Efficiency.

Overcoming the trade-off between short-circuited current (Jsc) and open-circuited voltage (Voc) is important to achieving high-efficiency organic solar cells (OSCs). Previous works modulated the energy gap between Frenkel local exciton (LE) and charge-transfer (CT) exciton, which served as the driving force of exciton splitting. Differently, our current work focuses on the modulation of LE-CT excitonic coupling (tLE-CT) via a simple but effective strategy that the 2-chlorothiophene (2Cl-Th) solvent utilizes in the treatment of OSC active-layer films. The results of our experimental measurements and theoretical simulations demonstrated that 2Cl-Th solvent initiates tighter intermolecular interactions with non-fullerene acceptor in comparison with that of traditional chlorobenzene solvent, thus suppressing the acceptor's over-aggregation and retarding the acceptor crystallization with reduced trap. Critically, the resulting shorter distances between donor and acceptor molecules in the 2Cl-Th treated blend efficiently strengthen tLE-CT, which not only promotes exciton splitting but also reduces non-radiative recombination. The champion efficiencies of 19.8 % (small-area) with superior operational reliability (T80: 586 hours) and 17.0 % (large-area) were yielded in 2Cl-Th treated cells. This work provided a new insight into modulating the exciton dynamics to overcome the trade-off between Jsc and Voc, which can productively promote the development of the OSC field.

Dimeric Small Molecule Acceptors via Terminal-End Connections: Effect of Flexible Linker Length on Photovoltaic Performance.

The dimerization of small molecule acceptors (SMAs) holds significant potential by combining the advantages of both SMAs and polymer acceptors in realizing high power conversion efficiency (PCE) and operational stability in organic solar cells (OSCs). However, advancements in the selection and innovation of dimeric linkers are still challenging in enhancing their performance. In this study, three new dimeric acceptors, namely DY-Ar-4, DY-Ar-5, and DY-Ar-6 are synthesized, by linking two Y-series SMA subunits via an "end-to-end" strategy using flexible spacers (octyl, decyl, and dodecyl, respectively). The influence of spacer lengths on device performance is systematically investigated. The results indicate that DY-Ar-5 exhibits more compact and ordered packing, leading to an optimal morphology. OSCs based on PM6: DY-Ar-5 achieves a maximum PCE of 15.76%, attributes to enhance and balance carrier mobility, and reduce carrier recombination. This dimerization strategy using suitable non-conjugated linking units provides a rational principle for designing high-performance non-fullerene acceptors.

Temperature-dependent charge transport measurements unveil morphological insights in non-fullerene organic solar cells

The morphological analysis of bulk heterojunction (BHJ) active layer stands as a critical imperative for advancing the performance of future organic solar cells. Conventional characterization tools employed for morphological investigation often require substantial resources, both in cost and physical space, thereby imposing restraints on research endeavors in this domain. Here, we extend the application of charge carrier transport characterization beyond conventional mobility assessments, utilizing it as a table-top method for preliminary morphological screening in organic thin films. The investigation focuses on several high-performance BHJ systems that utilize typical “Y” non-fullerene acceptors. It involves in-depth transport studies, including temperature- and field-dependent transport characterizations. The resulting transport data are analyzed in detail using the Gaussian disorder model to extract key transport parameters, specifically the high-temperature limited mobility (μ∞) and positional disorder (∑). Integrating these transport parameters with morphological insights obtained through various characterization tools—including x-ray scattering, sensitive spectroscopy, and quantum chemistry simulation—provides a deep understanding of the intricate interplay between charge transport properties and morphological characteristics. The results reveal explicit relationships, associating μ∞ with the degree of molecular stacking in BHJs and ∑ with the structural disorder in molecule skeleton. Our findings point to the promising potential of utilizing a simple transport characterization technique for the early stage evaluation of thin film packing and geometric properties of organic materials.

Efficient solution-processed near-infrared organic light-emitting diodes with a binary-mixed electron transport layer

A binary-mixed electron transport layer (ETL) has been reported for constructing solution-processable near-infrared organic light-emitting diodes (NIR OLEDs). Relative to the single-component ETL, the binary-mixed ETL composed of PDINN:TPBi can enhance the carrier transport capacity, reduce device impedance, and weaken fluorescence quenching of the emitting layer. By carefully selecting an appropriate luminescent material Y5 (a nonfullerene electron acceptor in organic solar cells) and precisely fine-tuning the molecular aggregation in active layer using a mixed solvent, the morphology is optimized and luminescence performance is enhanced, resulting in efficient NIR OLEDs with an emission peak at 890 nm. The experiment showcases a Y5-based near-infrared OLED with a maximum radiance of 34.9 W sr-1 m-2 and a maximum external quantum efficiency of 0.50%, which is among the highest values reported for non-doped fluorescent NIR OLEDs with an emission peak over 850 nm.