Negative Electrocaloric Effect Research Articles

Design of polar boundaries enhancing negative electrocaloric performance by antiferroelectric phase-field simulations

Electrocaloric refrigeration which is environmentally benign has attracted considerable attention. In distinction to ferroelectric materials, which exhibit an extremely high positive electrocaloric effect near the Curie temperature, antiferroelectric materials represented by PbZrO3 have a specific negative electrocaloric effect, i.e., electric field decreases the temperature of the materials. However, the explanation of the microscopic mechanism of the negative electrocaloric effect is still unclear, and further research is still needed to provide a theoretical basis for the negative electrocaloric effect enhancement. Herein, the antiferroelectric phase-field model has been proposed to design polar boundaries enhancing antiferroelectric negative electrocaloric performance in PbZrO3-based materials. Based on this, we have simulated the polarization response and domain switching process of the temperature and electric field-induced antiferroelectric—ferroelectric phase transition. It is shown that the temperature range tends to increase as the density of polar boundaries increases from the antiferroelectric stripe domain, polymorphic domain to the nanodomain. Among them, the peak adiabatic temperature change of antiferroelectric nanodomains can reach −13.05 K at 84 kV/cm, and a wide temperature range of about 75 K can be realized at 42 kV/cm. We expect these discoveries to spur further interest in the potential applications of antiferroelectric materials for next-generation refrigeration devices.

The Influence of Measurement Conditions on the Electrocaloric Effect in Ferroelectric Ceramics of Modified Barium Titanate.

In this work, the electrocaloric effect (ECE) and electrocaloric strength (ΔT/E) were measured and thermal and dielectric studies were performed on Pb-modified BaTiO3 (BPT). The saturated hysteresis loops and normal ferroelectric behavior of the ferroelectric ceramics allow the utilization of the indirect method to estimate the electrocaloric properties. The electrocaloric measurements were performed under high (18 kV/cm) versus low (8 kV/cm) electric field conditions. These conditions were chosen to notice and then eliminate an artificial negative electrocaloric effect in the tested ceramics. At the same time, relatively high values of positive electrocaloric temperature change ΔT (~ 2.19 K) and electrocaloric strength ΔT/E (~0.27-0.11 K·cm/kV) were obtained.

Boosting room-temperature electrocaloric performance in B-site complex antiferroelectrics: A synergistic design approach

As an emerging eco-friendly solid-state refrigeration technology boasting high energy conversion efficiency, there is a pressing demand for ferroelectrics exhibiting significant electrocaloric effect (ECE) at room temperature (RT) for refrigeration applications. In this study, guided by phase-field simulation, we explore the potential of B-site complex Pb[Mg(1–x)ZnxW]1/2O3 (PMZW100x) antiferroelectrics (AFE) to deliver promising symmetric positive and negative ECE near ambient temperature. The first-order AFE-paraelectric (PE) phase transition occurring around 50 °C induces a substantial change in heat quantity and yields prominent ECE upon electric excitation. Maxwell characterization reveals a potential combination of positive and negative ECE, showcasing significant advantages in cooling capacity. Given the technical limitations of existing direct methods for testing under elevated electric fields, low-field ECE is validated using the heat flux approach to ensure the legitimacy of results. Direct measurements demonstrate a high positive ΔT value of 2.76 K at 52 °C and a negative ΔT of –2.91 K at 44 °C (under 140 kV cm–1), surpassing traditional PbZrO3 bulk materials. The coexistence of substantial positive and negative ΔT near RT in PMZW100x offers a new avenue for developing highly efficient solid-state cooling devices.

High energy-storage density and giant negative electrocaloric effect in PLZS antiferroelectric thick film ceramics prepared via the tape-casting process

Antiferroelectric materials are highly desired for high energy-storage density capacitors and electrocaloric refrigerator in the future due to their excellent energy storage properties and giant negative electrocaloric effect, which have attracted great attention in recent years. In the present work, a highly recoverable energy density (Wrec) and a large reversible adiabatic temperature change (ΔT) were obtained simultaneously in PLZS thick film ceramics (TFCs). A maximum Wrec of 9.84 J·cm−3 with an efficiency of 85.2 % at 440 kV·cm−1, and a negative ΔT of −9.50 °C at 280 kV·cm−1 were obtained. Moreover, the maximum value of electrocaloric strength of 0.98 K·m·MV−1 was achieved for Pb0.97La0.02(Zr0.50Sn0.50)O3 TFCs. These results demonstrate that the PLZS TFCs can be applied potentially for high energy-storage density capacitors and refrigerators.

Achieving large negative electrocaloric effect in AgNbO3-based antiferroelectric ceramics based on dipole disordering

The electrocaloric effect (ECE) is considered as an environmentally friendly refrigeration technology, which can be used to replace vapor compression refrigeration. Lead-free antiferroelectric (AFE) ceramics are promising electrocaloric materials because of large saturation polarization and polarization change with temperature, which can generate large positive or negative ECE. In this work, the lead-free Ag(Nb1-0.8xHfx)O3 (x = 0, 0.001 and 0.003) AFE ceramics are fabricated through a conventional solid-state reaction method which shows a decreased the phase transition temperature of M1 - M2 toward room temperature (RT), and a large negative ECE (ΔT = −2.3 K under 130 kV cm−1) is obtained near the ambient temperature by using an indirect measurement in ANH0.001 AFE ceramic. The large negative ECE behavior is ascribed to dipole disordering (i.e. the anti-parallel dipoles are broken and gradually becomes disordered under an external electric field) resulting from the field-induced phase transition under a modest electric field. This work shows that AgNbO3-based AFE ceramics could be used in the refrigeration devices as an electrocaloric material.

Phenomenological analysis of positive and negative electrocaloric effects in Rochelle salt

Ferroelectrics exhibiting both positive and negative electrocaloric effects stand out as promising materials for achieving high-efficiency solid-state refrigeration. The phase transition is acknowledged as a crucial factor in designing such materials. This study investigates the electrocaloric behavior and its correlation with phase transitions in Rochelle salt single crystal using Landau thermodynamic theory. Analysis of free energy density, ferroelectric, and dielectric data uncovers a complex temperature-dependent phase transition sequence of paraelectric–ferroelectric–paraelectric. This imparts Rochelle salt single crystal with intriguing field-induced phase transition behaviors and electrocaloric responses. Pronounced positive and negative electrocaloric effects are, respectively, observed near the high-temperature and low-temperature Curie point. The opposite sign of entropy differences between the ferroelectric and the two paraelectric phases is identified as the origin of the difference in electrocaloric response. These findings not only enhance our understanding of the electrocaloric effect but also provide a design solution for materials with the coexistence of positive and negative electrocaloric effects.

Field-Induced Antiferroelectric-Ferroelectric Transformation in Organometallic Perovskite Displaying Giant Negative Electrocaloric Effect.

Antiferroelectric materials with an electrocaloric effect (ECE) have been developed as promising candidates for solid-state refrigeration. Despite the great advances in positive ECE, reports on negative ECE remain quite scarce because of its elusive physical mechanism. Here, a giant negative ECE (maximum ΔS ∼ -33.3 J kg-1 K-1 with ΔT ∼ -11.7 K) is demonstrated near room temperature in organometallic perovskite, iBA2EA2Pb3I10 (1, where iBA = isobutylammonium and EA = ethylammonium), which is comparable to the greatest ECE effects reported so far. Moreover, the ECE efficiency ΔS/ΔE (∼1.85 J cm kg-1 K-1 kV-1) and ΔT/ΔE (∼0.65 K cm kV-1) are almost 2 orders of magnitude higher than those of classical inorganic ceramic ferroelectrics and organic polymers, such as BaTiO3, SrBi2Ta2O9, Hf1/2Zr1/2O2, and P(VDF-TrFE). As far as we know, this is the first report on negative ECE in organometallic hybrid perovskite ferroelectric. Our experimental measurement combined with the first-principles calculations reveals that electric field-induced antipolar to polar structural transformation results in a large change in dipolar ordering (from 6.5 to 45 μC/cm2 under the ΔE of 18 kV/cm) that is closely related to the entropy change, which plays a key role in generating such giant negative ECE. This discovery of field-induced negative ECE is unprecedented in organometallic perovskite, which sheds light on the exploration of next-generation refrigeration devices with high cooling efficiency.

Electrocaloric effects of Ba1-xCaxTi0.9Zr0.1O3 through both direct and indirect measurements

The electrocaloric effect (ECE) of lead-free BaTiO3 based materials has drawn considerable attention for application in next-generation refrigeration, which has been widely investigated through indirect measurement methods; however, this method is sometimes ineffective because negative and positive ECEs coexist in one material. The paradox of ECE phenomena should be clarified; therefore, in this work, the ECEs of modified BaTiO3 were investigated through both direct and indirect measurement methods. The investigated BaTiO3 compositions herein are (Ba1-xCax)(Ti0.9Zr0.1)O3 (0.05 ≤ x ≤ 0.20), abbreviated as BZT-100xCa. Through indirect measurements, the ECE reached its maximum value around the Curie temperature TC, and the coexistence of negative and positive ECEs was observed in BZT-5Ca, BZT-10Ca, and BZT-15Ca. A laboratory-built ECE direct measurement system utilizing a platinum resistor was used to measure the ECE of BZT-100xCa. Through direct measurement, the maximum ECE appears several Kelvins above the TC, which coincides with the ECE through the indirect measurement, but no negative ECE is observed. Meanwhile, the ECE measured through direct measurement was smaller than that measured through indirect measurement. Through direct measurements, BZT-15Ca exhibited the largest ΔT of 0.291 K and ΔT/ΔE of 0.182 × 10−6 K m/V under 16 kV/cm, indicating that BZT-15Ca has a better ECE performance than previously reported modified BaTiO3 ceramics. By comparison, it can be concluded that the ECE through the indirect measurement method can reflect the approximate variation tendency of the actual ECE, and the negative ECE measured indirectly should be certified through direct measurement method, which doesn't influence the reliability of ECE through the indirect measurement.

Colossal negative electrocaloric effects in anti-ferroelectric PLZST bulk ferroelectrics for solid-sate refrigeration

Colossal negative electrocaloric effects in anti-ferroelectric PLZST bulk ferroelectrics for solid-sate refrigeration

Giant negative electrocaloric effect measured by indirect method in X-ray irradiated P(VDF-TrFE) films

Flexible solid-state cooling devices with high efficiency are attracted to ferroelectric polymers with excellent negative electrocaloric (EC) effects. It is challenging to obtain a large negative EC effect in ferroelectric polymers due to the lack of tunable techniques. A giant negative EC response was obtained in the poly(vinylidene fluoride-trifluoroethylene) copolymers (P(VDF-TrFE), 70/30, in mole ratio) irradiated with high-energy X-ray. The irradiated P(VDF-TrFE) films showed an adiabatic temperature change of −13.5 K at 40 MV/m under a dose of 5 Mrad (1 Mrad=104 J/kg) obtained by the indirect method. This significant negative EC effect is attributed to the enhancement of crystalline due to the entry of polymer molecules into the amorphous to crystalline structure and the reduction of heat capacity due to the increase of crosslinking. In addition, X-ray irradiation improves the dielectric coefficient from 15 to 22. This research indicates that irradiation can modify the negative EC properties of ferroelectric polymers for solid-state cooling.

Positive and Negative Electrocaloric Effect in soft- and hard-doped commercial PZT ceramics

The electrocaloric properties of commercially modified Pb(Zr,Ti)O3- (PZT)-based soft and hard ceramics were investigated by the indirect estimation via measurement of temperature–electric field P (T,E) hysteresis loops. The adiabatic temperature change ΔT due to electrocaloric effects was estimated from the polarization change of these samples. Both positive and negative electrocaloric temperature change was obtained for all ceramics. The existence of the negative electrocaloric effect was related to the FE-FE field-induced phase transition, between rhombohedral and monoclinic phases that occur in PZT ceramics synthesized near the morphotropic phase boundary. The resulting negative electrocaloric temperature change reveals higher values for the hard-type ceramics (∼-1.5 K for PIC 300) than for the soft-type. Insignificant positive effect values were achieved for all ceramics. The highest values of positive ECE were recorded for PIC 155 (soft) and PIC 181 (hard) and are of the order of ΔT = 0.67 K. In this case, no correlation was observed between the type of PZT ceramics soft or hard.

Large electrocaloric effects induced by multidomain-to-monodomain transition in ferroelectrics with electrical inclusions

The electrocaloric effect (ECE) depends on the sudden change of the polarization field during ferroelectric phase transition near the Curie temperature. Similarly, giant ECE can be found enormously during the domain structure transition from multidomain to monodomain process in ferroelectrics. To reveal the mechanism with the effects of the electric inclusions, the ECE of PbTiO3 (PTO) ferroelectric solids under electric loads is investigated by phase-field simulation. The giant ECEs of ferroelectric materials containing three kinds of electric inclusions, namely, air, silicone oil, and water, are discussed in detail under applied electric fields. The results suggest that an unusual ultrahigh negative ECE (−9.30 K) and a large EC strength (∆T/∆E=0.237 KmMV−1 are achieved near room temperature (about 50°C) in ferroelectrics containing water inclusion. The results indicate that electric inclusions generate high electrostatic energy under electric loads to break through the energy barrier and play an importation role in the ECE. In summary, the works may provide a better way to obtain the giant ECE and large EC strength close to room temperature by effectively regulating the dielectric constant of the electric inclusion and the increment of the applied electric field.

Phonon entropy engineering for caloric cooling

Electrocaloric cooling, with the advantages of zero global warming potential, high efficiency, smart size, etc., is regarded as a promising next-generation technology for green refrigeration. The exotic negative electrocaloric effect (ECE) in antiferroelectric materials forms the basis to improve the caloric cooling power density, but the underlying mechanism remains elusive. By using a fully first-principles method, we successfully simulate the electric field-triggered structural phase transition from antiferroelectric to ferroelectric in a prototypical antiferroelectric material PbZrO3 (PZO). Through tracking the phonon entropy evolution and measuring the temperature-dependent polarization along the transition path, we disclose that the negative ECE in PZO originates from the latent heat associated with phonon entropy rather than the previously recognized dipolar entropy. Accordingly, a new concept of phonon entropy engineering is proposed that engineering the density of states especially for low-frequency phonons can modulate the phonon entropy, which provides an effective route to enhance the cooling power density.

Order-degree-modulated ferroic response and an unconventional electrocaloric effect in B-site complex systems: a case study in Pb[(Yb1/2Nb1/2)0.84(Mg1/3Nb2/3)0.16]O3 ceramic

The order-degree-modulated ferroic response and electrocaloric effect (ECE) in Pb(B1,B2)O3-type B-site complex antiferroelectrics (AFEs) are explored in this work. The results show that local/phase structure and dielectric/ferroic properties are strikingly dependent on the degree of order (high, intermediate and low for samples S1, S2 and S3, respectively). A decrease in the content of the AFE orthorhombic phase and an increase in the weakly polar disorder phase is observed from S1 to S3, accompanied by an enhanced relaxation behavior with a smearing of the AFE-to-paraelectric phase transition. Ferroic and EC responses in the three samples present distinct features. Antiferroelectricity wakes-up significantly in sample S1, which boosts the ECE to ∼0.95 K and is almost three times that of S3 (∼0.23 K). An abnormal ECE [negative ECE with a hop–hop character and asymmetrical electrocaloric (EC) response] is unexpectedly found in sample S1. The underlying mechanism is unveiled by dipolar relaxation and phenomenology analysis, which states that the AFE coupling strength dominates the EC performance in this AFE. This work not only presents a refreshing method for order-degree regulation of the ECE in B-site complex AFEs, but also clarifies the possibility that AFEs with robust dipolar coupling strength have an unconventional ECE.

Performance Study on an Electrocaloric Heat Pump Based on Ga-Based Liquid Metal

A solid-state heat pump using the electrocaloric effect (ECE) provides a new idea for the future development of heat pumps. However, most of the electrocaloric (EC) heat pumps presented in the literature are low in efficiency and use at least one moving part, which significantly reduces the reliability of the heat pump and adds to its complexities. In this context, combining the positive and negative ECEs, we proposed a plate-laminar non-mobile EC heat pump adopting Gallium-based liquid metal as an intermediate medium to guarantee highly efficient heat transfer. Numerical simulation in COMSOL Multiphysics has been performed to investigate the correlation between different operating parameters and the performance of the EC heat pump. Changing the temperature span only, a COP of 8.13 and a UVHP of 746.1 W·dm−3 were obtained at a temperature span of 7 K. It was also found that the UVHP increased by 28.45% and COP increased by 25.46% after adding one layer of EC material. The electric-induced quantity of heat and cooling capacity was found to significantly affect the heating performance. The biggest heating power of 7132.7 W·dm−3 was obtained under 200 MV·m−1, and the biggest COP of 14.84 was obtained under 150 MV·m−1 at a cyclic period of 8 s. This study provides a highly efficient, non-mobile EC heat pump that employs fluid-thermal conjugated heat transfer, and exploration of the parameters makes the optimization of the heat pump possible by fine-tuning the operation parameters.

Large negative electrocaloric response induced by nanoscale phase transition in (Bi, Na)TiO3-based thin films

Electrocaloric effect (ECE) offers an efficient and environmentally friendly route for solid-state cooling. Either positive or negative ECE could exhibit a large adiabatic temperature change (ΔT). Compared to the positive electrocaloric response, the investigation of negative ECE is lagging behind, largely due to the fact that its origin is still elusive. In this work, the negative ECE behavior of conventional ferroelectric thin films, namely 0.94(Bi0.5Na0.5)TiO3-0.06BaTiO3 (BNBT), was studied. A remarkable ΔT of −26.1 K was acquired near 160 °C under a moderate electric field of 875 kV/cm, attributing to the ferroelectric phase transition in the polar nanoregions from rhombohedral (R3c) to tetragonal (P4bm), as confirmed by temperature-dependent dielectric permittivity, Raman spectra, and x-ray reciprocal space mapping. The BNBT thin film presents a high electrocaloric coefficient (ΔT/ΔE) of 0.0298 K cm kV−1, transcending that of the most reported negative electrocaloric response of thin films.

Positive and Negative Electrocaloric Effect in Lead-Free Silver Niobate Antiferroelectric Ceramic Depending on Affluent Phase Transition

We prepared a dense AgNbO3 ceramic using a conventional solid-state reaction method. The phase structure, electrical properties and electrocaloric effect (ECE) were systematically investigated. Large negative and positive ECEs (−4.38 °C at 65 °C and 2.3 °C at 210 °C) under an external electric field of 180 kV·cm−1 were obtained in the eco-friendly AgNbO3 antiferroelectric (AFE) ceramic due to affluent phase transition and a high electric field. The large positive and negative ECEs originated from the phase transition between ferrielectric (FIE) phases (the orthorhombic space group (Pmc21) and AFE phases (Pbcm) tuned by an applied external field. Additionally, a probable mechanistic model was proposed to illustrate the generation of positive and negative ECEs. This study may provide guidelines for the design of high-efficiency solid-state cooling devices.

Origin of negative electrocaloric effect in Pnma -type antiferroelectric perovskites

Electrocaloric materials of solid state hold great promise for next-generation high-efficiency cooling technology. Besides the normal electrocaloric effect (ECE) in ferroelectrics or relaxors, anomalous ECE with decreasing temperature upon application of an electric field is known to occur in antiferroelectrics (AFEs), and previous understanding refers to the field-induced canting of electric dipoles if there is no phase transition. Here we use a first-principles-based method to study the ECE in Nd-substituted ${\mathrm{BiFeO}}_{3}$ (BNFO) perovskite solid solutions, which has a Pnma-type AFE ground state. We demonstrate another scenario to achieve and explain anomalous ECE, emphasizing that explicit consideration of octahedral tiltings is indispensable for a correct understanding. This mechanism may be general for AFEs for which the antipolar mode is not the primary order parameter or for other commonly occurring Pnma-type perovskites, even without being AFEs. We also find that the negative ECE can reach a large magnitude in BNFO.

Simultaneous enhancement of the electrocaloric effect and electrostrain via exploiting the reversible polarization rotation

Self-actuating ferroelectric cooling technology have drawn increasing attention for its extensive application prospect, where simultaneous enhancement of electrocaloric effects (ECE) and electrostrain (ES) in ferroelectric materials is necessary prerequisites for the efficient operation of the cooling system. In this work, we proposed a self-actuating dual cooling cycle system combining the positive and negative ECE/ES effect, and further confirmed its feasibility in 0.7 Pb(Mg1/3Nb2/3)O3-0.3PbTiO3 (PMN-30PT) single crystal via bipolar electric field regulation. A suitable reverse electric field can generate negative ECE and ES simultaneously due to the reversible polarization rotation, whereas a high reverse electric field will lead to a serious perform loss as a result of emergent irreversible polarization jumping. The optimal reverse electric field (-Eop) can enhance the total ECE and ES by 31% and 17% respectively, whose effective combination can significantly improve the cooling capacity of the self-actuating cooling system. Moreover, compared to traditional P-E and/or I-E measurements, we proposed a more applicable and precise method to determine the -Eop under square-wave DC electric field, i.e. capacitance-voltage measurement. Our work not only provides new ideas for improving the ECE and ES of the ferroelectric materials, but also promotes the design of ferroelectric cooling systems.

Giant Negative Electrocaloric Effect over an Ultra-Wide Temperature Region in Relaxation Frozen State Ferroelectrics

A giant negative electrocaloric effect with the electrocaloric temperature change range from -27.3 to -9.8 K over an ultra-wide temperature region of 260 K (-180 to 80 °C) is obtained in a relaxation frozen state ferroelectric film of Bi5Ti3AlO15. A strategy is proposed to extend the temperature region of the electrocaloric effect by gradually slowing and locally freezing the relaxation dynamics. The slow and frozen nanodomains below freezing temperature Tf of ∼80 °C do not yield to the applied electric field but are noncolinear to the field, which results in an inverse configuration entropy change and negative electrocaloric effect over an ultra-wide temperature region in frozen relaxor state ferroelectric films. A semiphenomenological model based on modified Ginzburg-Landau-Devonshire theory is presented to reveal the evolution of the slowing and freezing of the nanodomains. The breakthroughs in the operating temperature region and cooling temperature change make relaxation frozen state ferroelectrics excellent electrocaloric refrigeration materials.