Near Field Research Articles

Sparsity-based direction-of-arrival estimation in the presence of near-field and far-field interferences for small-scale platform sonar arrays.

For the sonar arrays mounted on an unmanned underwater vehicle (UUV), the direction-of-arrival (DOA) estimation of the far-field (FF) weak sources is influenced by the near-field (NF) interferences generated from the radiated self-noise of the UUV and the FF interferences simultaneously. To address the problem, a sparsity-based DOA estimation method resistant to the NF and FF interferences is proposed in this paper. This method isolates the FF signals from the NF signals by sparse reconstruction. Additionally, subspace projection is applied to address the masking problem of the weak target signal by the strong interferences in the spatial domain, effectively enhancing the capacity of estimating the DOA of the weak target signal in the presence of strong interferences. Numerical simulations and experimental results demonstrate the effectiveness of the proposed method. Compared to other advanced DOA estimation methods, the proposed method exhibits better DOA estimation performance in the presence of strong NF and FF interferences.

A 3-D Near-Field Source Localization Approach Based on the Combination of a Phase Interferometer, the Centroid Algorithm and the Perpendicular Foot Algorithm.

In this study, several 3-dimensional (3-D) parameter estimation and localization algorithms for wireless near-field (NF) sources are proposed employing the uniform circular array (UCA) structure. In the single-base-station case, the algebraic relation is demonstrated between the azimuth angle under the far-field (FF) assumption and the actual NF source firstly. Secondly, two groups of antenna pairs are selected with distances less than half the wavelength, which are called short baselines in the interferometer method. The foregoing short-baseline method is qualified to localize an NF source. In addition, a long-baseline method is also proposed with further research. Two groups of antenna pairs with distances greater than half the wavelength are selected as two long baselines. In the multiple-base-stations case, another two novel algorithms are also proposed. The first one is the centroid algorithm, which is based on the centroid calculation of three estimated source locations. And the second one is the perpendicular foot algorithm, which takes the perpendicular foot within three estimated source locations as the final positioning location. Simulation results illustrate that the proposed algorithms can achieve higher localization accuracy than the conventional 3-D Root MUSIC method. Moreover, the long-baseline method performs better than the short-baseline method. And it is also shown that the proposed perpendicular foot algorithm shows better performance than the proposed centroid algorithm.

Detailed analysis of electrogram peak frequency to guide ventricular tachycardia substrate mapping.

Differentiating near-field (NF) and far-field (FF) electrograms (EGMs) is crucial in identifying critical arrhythmogenic substrate during ventricular tachycardia (VT) ablation. A novel algorithm annotates NF-fractionated signals enabling EGM peak frequency (PF) determination using wavelet transformation. This study evaluated the algorithms' effectiveness in identifying critical components of the VT circuit during substrate mapping. A multicentre, international cohort undergoing VT ablation was investigated. VT activation maps were used to demarcate the isthmus zone (IZ). Offline analysis was performed to evaluate the diagnostic performance of low-voltage area (LVA) PF substrate mapping. A total of 30 patients encompassing 198 935 EGMs were included. The IZ PF was significantly higher in sinus rhythm (SR) compared to right ventricular paced (RVp) substrate maps (234 Hz (195-294) vs. 197 Hz (166-220); P = 0.010). Compared to LVA PF, the IZ PF was significantly higher in both SR and RVp substrate maps (area under curve, AUC: 0.74 and 0.70, respectively). The LVA PF threshold of ≥200 Hz was optimal in SR maps (sensitivity 69%; specificity 64%) and RVp maps (sensitivity 60%; specificity 64%) in identifying the VT isthmus. In amiodarone-treated patients (n = 20), the SR substrate map IZ PF was significantly lower (222 Hz (186-257) vs. 303 Hz (244-375), P = 0.009) compared to amiodarone-naïve patients (n = 10). The ≥200 Hz LVA PF threshold resulted in an 80% freedom from VT with a trend towards reduced ablation lesions and radiofrequency times. LVA PF substrate mapping identifies critical components of the VT circuit with an optimal threshold of ≥200 Hz. Isthmus PF is influenced by chronic amiodarone therapy with lower values observed during RV pacing.

Three-Dimensional Probe Mispositioning Errors Compensation: A Feasibility Study in the Non-Redundant Helicoidal Near to Far-Field Transformation Case

A feasibility study on the compensation of 3D mispositioning errors of the probe occurring in the characterization of a long antenna, via a non-redundant (NR) near to far-field (NTFF) transformation with helicoidal scan, is conducted in this article. Such types of errors can result from imperfections in the rail driving the linear motion of the probe and from an imprecise synchronization of the linear and rotational movements of the probe and the antenna when drawing the scan helix. To correct them, an approach, which proceeds through two steps, is proposed. The former step uses a technique called cylindo rical wave (CW) correction for compensating the phase of the near-field (NF) samples, which, owing to the rail imperfections, result in not being acquired over the measurement cylinder surface. The latter exploits an iterative scheme to restore the samples at the sampling points required by the adopted NR representation along the scan helix from those obtained by applying the CW correction technique and impaired by 2D mispositioning errors. The so compensated NF samples are then effectively recovered via a 2D optimal sampling interpolation (OSI) scheme to accurately obtain the input data required to carry out the standard cylindrical NTFF transformation. The OSI representation is determined here by assuming a long antenna under test as enclosed in a prolate ellipsoid or cylinder ending into two hemispheres (cigar) in order to make, depending on the particular geometry of the considered antenna, the representation effectively non-redundant. The reported numerical simulation results show the capability of the proposed approach to compensate even severe 3D mispositioning errors, thus enabling its usage in a real measurement scenario.

A Roadmap for NF-ISAC in 6G: A Comprehensive Overview and Tutorial.

Near-field (NF) integrated sensing and communication (ISAC) has the potential to revolutionize future wireless networks. It enables simultaneous communication and sensing operations on the same radio frequency (RF) resources using a shared hardware platform, maximizing resource utilization. NF-ISAC systems can improve communication and sensing performance compared to traditional far-field (FF) ISAC systems by exploiting the unique propagation characteristics of NF spherical waves with an additional distance dimension. Despite its potential, NF-ISAC research is still in its early stages, and a comprehensive survey of the technology is lacking. This paper systematically explores NF-ISAC technology, providing an in-depth analysis of both NF and FF systems, their applicability in various scenarios, and different channel models. It highlights the advantages and philosophies of ISAC, examining both narrow-band and wide-band NF-ISAC systems. Case studies and simulations offer deeper insights into NF-ISAC design philosophies. Additionally, the paper reviews the existing NF-ISAC literature, methodologies, potentials, and conclusions, and discusses future research areas, challenges, and applications.

Superchiral Light Emerging from Bound States in the Continuum in Metasurfaces of Si Nanorod Dimers.

Bound states in the continuum (BICs) in all-dielectric metasurfaces enhance light-matter interaction at the nanoscale due to their infinite Q factors and strong field confinement. Among a variety of phenomena already reported, their impact on chiral light has recently attracted great interest. Here we investigate the emergence of intrinsic and extrinsic optical chirality associated with the excitation of BICs in various metasurfaces made of Si nanorod dimers on a quartz substrate, comparing three cases: parallel nanorods (neutral) and shifted and slanted dimers, with/without index-matching superstrate. We analyze both the circular dichroism (CD) of the far-field (FF) interaction and the helicity of the near-field (NF) distribution. We show that the best approach to achieve chiral response in the FF based on extrinsic chirality is to exploit quasi-BICs (q-BICs) appearing in the case of slanted nanorod dimers. By contrast, the helicity density is largely enhanced in the case of shifted dimers, as it presents intrinsic chirality, with values 2 orders of magnitude larger than those of circularly polarized plane waves. These so-called superchiral electromagnetic fields concentrated at the nanoscale within the metasurface hold promise of appealing implications in phenomena such as strong-coupling, photoluminescence emission, or other local light-matter interactions.

Comprehensive evaluation of seismic fragility in base isolated buildings enhanced with supplemental dampers considering pounding phenomenon

Base isolation is a proven technology effective in minimizing earthquake-induced damage to both the structural and non-structural elements (especially freestanding contents) of buildings. Nevertheless, it has been shown that allowing the flexible isolation layer to endure substantial demand displacements might subject the isolated structure to failure. This vulnerability arises from potential superstructure yielding due to increased deformations and reduced stiffness, such as those occurring through pounding against a moat wall during intense earthquakes. One alternative to controlling these large deformations is to use supplementary dampers at the isolation plane of the building, creating a hybrid base isolation system (HIS), which adds damping to the isolation system. In this research, the seismic performance of base isolated structures with lead-rubber bearing (LRB) are studied in conjunction with linear viscous dampers (LVD). Due to this aim, a base-isolated steel frame with 2 story X-type braces and a surrounding moat wall is modeled with two various configurations: LRB, and LRB with LVD. Fragility curves are developed for an ensemble of near-field (NF) pulse-like ground motions and for the maximum inter-story drift ratio (MIDR) as an engineering demand parameter (EDP). The incremental dynamic analysis (IDA) is conducted to calculate the damage probability of the structure by assuming different threshold values for damage states. It was found that adding viscous dampers to the isolation system balanced the behavior of the structure under near field pulse-type records; resulting in reduced isolation displacement while its adverse effects are insignificant and can be ignored. Moreover, the median spectral acceleration, namely the spectral acceleration associated to a probability of exceedance (POE) equal to 50 %, at the specific limit state, in the hybrid base isolation system is higher compared to the conventional one.

Near-field detection and peak frequency metric for substrate and activation mapping of ventricular tachycardias in two- and three-dimensional circuits.

Successful ventricular arrhythmia (VA) ablation requires identification of functionally critical sites during contact mapping. Estimation of the peak frequency (PF) component of the electrogram (EGM) may improve correct near-field (NF) annotation to identify circuit segments on the mapped surface. In turn, assessment of NF and far-field (FF) EGMs may delineate the three-dimensional path of a ventricular tachycardia (VT) circuit. A proprietary NF detection algorithm was applied retrospectively to scar-related re-entry VT maps and compared with manually reviewed maps employing first deflection (FDcorr) for VT activation maps and last deflection (LD) for substrate maps. Ventricular tachycardia isthmus location and characteristics mapped with FDcorr vs. NF were compared. Omnipolar low-voltage areas, late activating areas, and deceleration zones (DZ) in LD vs. NF substrate maps were compared. On substrate maps, PF estimation was compared between isthmus and bystander sites. Activation mapping with entrainment and/or VT termination with radiofrequency (RF) ablation confirmed critical sites. Eighteen patients with high-density VT activation and substrate maps (55.6% ischaemic) were included. Near-field detection correctly located critical parts of the circuit in 77.7% of the cases compared with manually reviewed VT maps as reference. In substrate maps, NF detection identified deceleration zones in 88.8% of cases, which overlapped with FDcorr VT isthmus in 72.2% compared with 83.3% overlap of DZ assessed by LD. Applied to substrate maps, PF as a stand-alone feature did not differentiate VT isthmus sites from low-voltage bystander sites. Omnipolar voltage was significantly higher at isthmus sites with longer EGM durations compared with low-voltage bystander sites. The NF algorithm may enable rapid high-density activation mapping of VT circuits in the NF of the mapped surface. Integrated assessment and combined analysis of NF and FF EGM-components could support characterization of three-dimensional VT circuits with intramural segments. For scar-related substrate mapping, PF as a stand-alone EGM feature did not enable the differentiation of functionally critical sites of the dominant VT from low-voltage bystander sites in this cohort.

Differentiation of high frequency near field versus far-field potentials in low voltage zones during sinus rhythm improves discrimination of local sites of termination during ventricular tachycardia

Abstract Background Ventricular tachycardia (VT) with structural heart disease (SHD) is often bad tolerated or presents with several inducible morphologies, this support mapping the arrhythmic substrate during sinus rhythm (SR). Poor discrimination between near-field (NF) and far-field (FF) electrogram (EGM) components in low voltage (LV) areas is the main limitation. The peak frequency (PF) associated with bipolar EGMs may distinguish NF from FF EGMs (Panel D). Objective To evaluate if PF combined with voltage mapping during SR enhances discrimination of the region of VT termination by radiofrequency application (RFa). Methods Bipolar activation and voltage maps were generated with a 16-pole grid catheter (HD Grid) during SR (Panel B). PF maps were retrospectively computed (Panel C). The maps were only analyzed if acute termination was achieved by focal RFa within a boundary diameter <1.5cm (Panel A). The mapped surface area (SA) was sub-regioned in termination (T-ZONE) and non-termination (NT-ZONE) zones. The T-ZONE surface was centered about the termination site and was allowed to extend to a rectangular kernel >0.5cm and <1.5cm across perpendicular axes, with the NT-ZONE encompassing the remainder mapped SA. Sensitivity (SE) and specificity (SP) of discrimination of the T-ZONE vs. NT-ZONE were measured according to the %SA covered at different LV thresholds (0.1-1.0mV in increments of 0.1mV - Panel F). LV high PF (LVHF) areas at different PF cutoffs from 150Hz (LVHF150) to 300Hz (LVHF300) were also assessed. Results 15 patients with SHD and sustained monomorphic VT were enrolled. 4 had 5 VT’s terminated by 1.4±0.9 focal RF lesions (60-74 y/o, 3 ischemic). All termination sites were located in a LVHF region mapped during SR (Panels B,C,E). The T-ZONE occupied 0.41±0.33cm /92.75±13.31cm global SA and consisted of 15±10 EGM points/1432±337 global points. T-ZONE voltage during SR (0.50±0.32mV) was significantly lower vs. global voltage (2.01±0.69mV, P<0.001), while T-ZONE PF was higher (324±51Hz) vs. global (270±37Hz, P<0.001). ROC discrimination of the T-ZONE yielded AUC’s of 0.79-LV alone, 0.87- LVHF150, 0.91-LVHF200 (Delta +12.2% vs LV alone, Panel F), 0.85-LVHF250 and 0.77-LVHF300. At a 0.7mV cutoff, LVHF200 yielded a balanced SE/SP of 0.89/0.87 vs. LV alone (0.90/0.63). Conclusion Assessment of regions with LVHF during SR improves SP for discrimination of sites of VT termination compared to LV alone.TV near field

Localization of critical isthmus in left atrial macroreentrant tachycardias: insights from peak frequency mapping during sinus rhythm and coronary sinus pacing

Abstract Background Successful ablation of left atrium macroreentrant tachycardia (LAMRT) has advanced significantly, benefiting from an enhanced understanding of reentrant mechanisms and technological innovations. However, challenges like difficult inductions and the presence of multiple coexistent LAMRTs can complicate tachycardia mapping, potentially resulting in recurrences during follow-up. Consequently, there is a growing need for strategies that focus on pinpointing the critical isthmus of conduction (CIC) in LAMRT circuits outside of tachycardia episodes. Peak frequency (PF) mapping, with its ability to discern near-field (NF) from far-field (FF) electrograms (EGMs) in low voltage areas, emerges as a valuable tool for precisely identifying these critical isthmuses. Purpose This study aims to investigate whether the accurate identification of the CIC in LAMRT circuits is achievable through PF mapping during sinus rhythm or coronary sinus pacing. Methods Patients with sustained LAMRT undergoing radiofrequency (RF) ablation were enrolled. Utilizing a 16-pole grid catheter (HD-Grid), bipolar voltage and activation maps were generated during LAMRT. PF maps were retrospectively computed. Voltage, activation, and PF maps were also created during sinus rhythm and coronary sinus pacing (500 ms). Potential CICs (P-CICs) were defined as areas with low voltage (<0.2 mV) and high PF (>250 Hz), covering a surface area of <2 cm2 by adjusting the PF threshold above 250 Hz. Only instances of LAMRT terminated by focal RF lesions (boundary <1.5 cm diameter) were included. Confirmed CICs (C-CICs) were identified at sites where LAMRT termination occurred due to RF application. The localization of P-CICs found during LAMRT, sinus rhythm (SR), and coronary sinus pacing (CSP) mapping, in relation to that of CIC, was analyzed, considering them matching if separated by <10 mm. Results Twenty-four consecutive patients with 26 atrial tachycardias (ATs) were prospectively enrolled, including 18 LAMRTs (270±63 ms) terminated by 2.2±2.9 focal RF lesions after 9.4±8.2 sec of energy delivery. A P-CIC was consistently identified at the tachycardia termination site during LAMRT mapping, with a visual cutoffs discrimination score (1-5) of 4.1±0.7, a mean P-P voltage cutoff <0.22±0.09 mV, and a mean PF cutoff >330±67 Hz in all patients. Importantly, P-CICs found during SR and CSP mapping matched those found during LAMRT mapping in all patients (figure). Conclusion PF mapping demonstrates precision in identifying the critical isthmus in LAMRT circuits during actual tachycardia episodes. Notably, the consistent identification of the CIC through PF mapping during sinus rhythm or coronary sinus pacing exhibits a high correlation with findings during LAMRT mapping. This approach holds promising potential for reducing arrhythmia recurrences, especially in scenarios involving multiple or unmappable LAMRTs.

Effect of material characteristics of lead rubber isolators on seismic performance of box girder bridge

Near-field (NF) earthquakes have distinct ground motions, forward directivity pulses, and fling-step motions, causing structural responses to differ from far-field (FF) earthquakes. Seismic isolation is regarded as a developed and successful technology that may be applied to enhance a structure’s functionality and safeguard it against catastrophic earthquake effects. The variation in mechanical properties of seismic isolation also significantly influences bridge seismic response. The study investigates the influence of lead rubber (LRB) isolators and the characteristics of ground motions on seismically isolated bridges, aiming to determine optimal parameters for minimal earthquake response. Key parameters include ground motion characteristics, characteristic strength (Q), and isolator flexibility. The study modeled the force-deformation behavior of isolators using bilinear behavior, reflecting the Bouc-Wen hysteric model. CSI Bridge was used to model seismically isolated steel box girder bridges, with eight natural accelerograms assessing a 2% probability of exceedance in 50 years. The peak responses of pier displacement (MPD), isolator hysteric energy (HED), base shear, and deck acceleration are chosen as the response parameters for the comparison. To evaluate the response parameters, the earthquake data are scaled to the three studied peak ground acceleration (PGA) levels of design level (0.2 g), extreme level (0.4 g), and rare-extreme level (0.8 g). The findings offer insight on the relevance of isolator stiffness and its influences on the seismic performance of isolated bridges. The study identifies minimum values for pier displacement, hysteric energy, deck acceleration, and base shear at specific Q/weight sustained by isolator (W) and time period (T) values. Recommendations are made for the preliminary seismic isolation design of bridges with LRB isolators, highlighting the importance of PGV to PGA ratio in earthquake damage assessment.

Multiplexing near- and far-field functionalities with high-efficiency bi-channel metasurfaces

Propagating waves and surface waves are two distinct types of light-transporting modes, the free control of which are both highly desired in integration photonics. However, previously realized devices are bulky in sizes, inefficient, and/or can only achieve one type of light-manipulation functionality with a single device. Here, we propose a generic approach to design bi-channel meta-devices, constructed by carefully selected meta-atoms possessing reflection phases of both structural-resonance and geometric origins, which can exhibit two distinct light-manipulation functionalities in near-field (NF) and far-field (FF) channels, respectively. After characterizing the scattering properties of basic meta-atoms and briefly stating the theoretical strategy, we design/fabricate three different meta-devices and experimentally characterize their bi-channel wave-control functionalities in the telecom regime. Our experiments show that the first two devices can multiplex the generations of NF and FF optical vortices with different topological charges, while the third one exhibits anomalous surface plasmon polariton focusing in the NF and hologram formation in the FF simultaneously. Our results expand the wave-control functionalities of metasurfaces to all wave-transporting channels, which may inspire many exciting applications in integration optics.

An Efficient Procedure to Compensate for the Errors Due to the Probe Mispositioning in a Cylindrical Near-Field Facility.

This paper deals with the compensation of the probe mispositioning errors occurring in a cylindrical near-field (NF) facility due to the imprecise control of the linear and azimuthal positioners allowing the cylindrical scanning and/or to their limited resolution and to defects in the rails guiding the linear motion. As a result, 3-D errors in the positioning of the probe at any sampling point, as prescribed by the adopted non-redundant representation, affect the accuracy of the NF measurements. An efficient procedure is here proposed to properly compensate for these errors. It involves two steps. The former allows one to correct the mispositioning errors due to the deviation of each actual sampling point from the nominal measurement cylinder. The latter makes use of an iterative technique to restore the NF samples at any sampling point fixed by the used non-redundant representation from the ones obtained at the previous step and affected by 2-D mispositioning errors. Once these steps have been fruitfully applied, the so-compensated NF samples are effectively interpolated through a 2-D optimal sampling interpolation (OSI) formula to accurately reconstruct the input data required to perform the traditional cylindrical near-to-far-field transformation. The OSI representation is here developed by considering an elongated antenna under test as enclosed either in a prolate spheroid or in a cylinder terminated by two half spheres (rounded cylinder) in order to make the representation effectively non-redundant. Numerical test results, which thoroughly prove the efficacy of the devised procedure in correcting even severe 3-D mispositioning errors, are reported.

Research on a Two-stage Plane Adaptive Sampling Algorithm for Near-field Scanning Acceleration

As one of the most useful methods in electromagnetic interference (EMI) diagnosis, near-field (NF) scanning is widely used in electromagnetic compatibility (EMC) evaluation of complex devices under test (DUTs). In this paper, a two-stage plane adaptive sampling algorithm is proposed to reduce the acquisition time in the process of NF scanning and to make reconstruction of the radiation source more efficient. The sampling method is based on the region self-growth algorithm and the Voronoi subdivision principle, significantly reducing the number of NF samples in the stage of solving the radiation source model through uniform and non-uniform two-stage sampling. Two experiments were conducted to verify the correctness and effectiveness by comparing with the traditional uniform sampling method.

Fast prediction of a high directivity antenna characterization for future wireless communication based on terahertz photonics

Fast prediction of high-directivity antenna characterization has been presented. The Cassegrain antenna working at J band frequency has been evaluated using a terahertz (THz) photonic system based on near-field measurement. The generation and detection of THz signal are based on a non-polarimetric electrooptic (EO) frequency down-conversion technique combined with a self-heterodyne system. The synthesis method is introduced to estimate far-field E and H-plane antenna characteristics. The antenna result is calculated using amplitude and phase-synthesized data based on the measured data. A near-field (NF) to far-field (FF) transformation is employed in the antenna radiation pattern. The effect of blocking objects on the antenna (supporting rods and sub-reflector) is discussed. The antenna characteristics of the measured and synthesized data are compared to the ITU F.699 recommendation. The synthesized result agrees with the measured one on the main lobe angle.

Tri-Polarized Holographic MIMO Surfaces for Near-Field Communications: Channel Modeling and Precoding Design

This paper investigates the utilization of triple polarization (TP) for multi-user (MU) wireless communication systems with holographic multiple-input multi-output surfaces (HMIMOSs), targeting capacity boosting and diversity exploitation without enlarging the antenna array sizes of the transceivers. We specifically consider that both the transmitter and receiver are equipped with an HMIMOS consisting of compact sub-wavelength TP patch antennas and operating in the near-field (NF) regime. To characterize TP MU-HMIMOS systems, a TP NF channel model is constructed using the dyadic Green’s function, whose characteristics are leveraged to design two precoding schemes for mitigating the cross-polarization and inter-user interference contributions. Specifically, a user-cluster-based precoding scheme that assigns different users to one of three polarizations, at the expense of system’s diversity, is presented together with a two-layer precoding technique that removes interference using a Gaussian elimination method. A theoretical correlation analysis for HMIMOS-based systems operating in the NF region is also derived, revealing that both the spacing of transmit patch antennas and user distance impact transmit correlation factors. Our numerical results showcase that the users located far from the transmit HMIMOS experience higher correlation than those closer in the NF region, resulting in a lower channel capacity. In terms of channel capacity, it is demonstrated that the proposed TP HMIMOS-based systems almost achieve 1.25 and 3 times larger gain compared to their dual-polarized version and conventional HMIMOS systems, respectively. It is also shown that the the proposed two-layer precoding scheme combined with two-layer power allocation realizes the highest spectral efficiency, among compared schemes, without sacrificing diversity.

Near-Field Matching and Universal Limits on Electromagnetic Energy Transfer

This article introduces the concept of near-field (NF) matching as a continuum-mode generalization of port matching in circuit theory suitable for field-theoretic electromagnetic energy transfer scenarios, with a focus on spatio-frequency processes in coupled systems. The concept is rigorously formulated using the full electromagnetic Green’s function of a generic receiving surface interacting with arbitrary illumination fields where the Riemannian structure and the electromagnetic boundary condition of the problem are encoded into the tensor structure of a Green’s function on a manifold. After a carefully selected combination of proper function spaces for the various field quantities involved, we utilize exact methods to estimate the sizes of various operator quantities using the appropriate function space norms. A field-theoretic measure of power transfer efficiency in generalized NF matching scenarios is introduced, and exact upper bounds on this efficiency are derived using Young’s inequality for integral kernel operators. This theoretical study complements and generalizes the largely empirical and problem-specific literature on wireless energy transfer by providing an exact and rigorous mathematical framework that can guide and inform future optimization and design processes.

Aramid nanofiber assisted preparation of 3D-oriented graphite/silicone composite slices with high through-plane thermal conductivity and efficient electromagnetic interference shielding

High-performance electromagnetic interference (EMI) shielding materials with outstanding thermal transfer ability are urgently needed for modern electronics. Here, efficient 3D-oriented graphite/silicone EMI shielding composite slices with high through-plane thermal conductivity were prepared through the construction of 3D-oriented graphite skeletons followed by incorporation of silicone and cutting. The flaky graphite was utilized as functional fillers, and an ultra-low addition of aramid nanofibers (ANFs) was conducted to construct the supporting frameworks to maintain the structure of 3D-oriented graphite skeletons. The strategy of constructing of 3D-oriented graphite skeletons before incorporating of silicone facilitated the forming of efficient electrically conductive network and thermal transfer pathway in the prepared composite slices. The differences in thermal, electrical and EMI shielding properties that originated from the orientation of interconnected flaky graphite were systematically studied. As a result, the composite slices show significant enhancements of EMI SE of 65.28 dB in X-band, 76.62 dB in Ka-band and through-plane thermal conductivity of 10.53 W m−1 K−1 at the graphite fraction of 32.68 vol%. Additionally, the composite slices exhibit a good near-field (NF) shielding performance at the frequency range of 1–9 GHz. The composite slices reveal substantial potential for advanced EMI shielding and thermal management applications.

Near-Field-to-Far-Field RCS Prediction Using Only Amplitude Estimation Technique Based on State Space Method

Measuring the radar cross-section (RCS) of a far-field (FF) target in engineering can be challenging, especially when remote measurement is difficult. To overcome this challenge, an FF RCS can be predicted by near-field (NF)-extrapolated transformation. However, due to the relative error between the theoretical and measured electric field (E-field) values in a NF, the extrapolation calculation of a FF can be carried out by correcting the NF amplitude. This paper proposes the use of the state space method (SSM) to estimate the amplitude-only of NF E-fields for improving the prediction accuracy of FFs. The simulation results demonstrate that the SSM can estimate NF amplitude, which can be transformed into a FF, and which can lead to improved prediction accuracy when compared to reference-FF-calculated and to circular-NF-to-FF-transform-(CNFFFT)-calculated RCSs.

A Mixed-Field Circular and Non-Circular Source Localization Algorithm Based on Exact Spatial Propagation Geometry.

In passive localization techniques, as the scale of the array of the sensors used increases, the source distribution may be a coexistence of near-field (NF) and far-field (FF) sources. Most of the existing algorithms dedicated to the localization of mixed-field sources are based on a simplified model, which has model errors and cannot make good use of non-circular properties when non-circular signals are present in the sources. In this paper, we present a mixed-field circular and non-circular source localization algorithm based on exact spatial propagation geometry. First, we make an initial estimate of the source parameters using exact spatial geometry relations. The MUSIC algorithm is then used in combination with the non-circular properties of the signal to achieve an accurate estimate. The algorithm does not lose performance due to model mismatch and is able to make good use of the non-circular properties of the sources to improve the estimation accuracy. The simulation results show that the proposed algorithm can effectively distinguish between sources and that the algorithm performs satisfactorily.