Nanoparticle Materials Research Articles

Self-Healing Glass/Metakaolin-Based Geopolymer Composite Exposed to Molten Sodium Chloride and Potassium Chloride

Geopolymers (GP) are a class of X-ray amorphous, nanoporous, nanoparticulate materials that can be mixed, poured, and cured under ambient conditions. Typically, geopolymers are made using a Group 1 (G1) alkali activator such as sodium or potassium metasilicate and an aluminosilicate precursor. An analogous material to GPs is ordinary Portland cement because of the similarities in processing, however, the resulting microstructure is more similar to that of a glass. Geopolymers are more thermally stable than OPC and can therefore be used in a variety of thermal energy storage systems, as energy storage is an increasing global concern. In this study, potassium metakaolin-based geopolymer composites containing glass particles and alumina platelets were manufactured, heated in air, and exposed to molten sodium chloride or potassium chloride under an air atmosphere. Results showed the formation of an amorphous self-healing geopolymer composite (ASH-G) that could contain molten G1 chlorides for over 200 h without signs of macro or microscopic chemical degradation. The filling of cracks by glass particles in the composite after heating to 850 °C makes this material self-healing. It was found that the morphology of ASH-G composites was more affected by temperature and duration than contact with corrosive molten chlorides in air. Future works include investigating the effect of molten salt on mechanical properties during initial heating, after prolonged heating, and the material compatibility with other molten Group 1 chloride eutectics.

A Review of Nanoparticle Material Coatings in Passive Radiative Cooling Systems Including Skylights

Daytime passive radiative cooling (DPRC) has remained a challenge over the past decades due to the necessity of precisely defined materials with a significantly high emissivity of thermal radiation within the atmospheric transparent window wavelength range (8–13 μm) as well as high reflectivity in the solar spectrum (0.2–3 μm). Fortunately, recent advances and technological improvements in nanoscience and metamaterials are making it possible to create diverse metamaterials. This enables the production of DPRC in direct solar irradiation. The development of a material that is appropriate for effective DPRC is also a noteworthy development in this field of technology. This review gives a thorough introduction and discussion of the fundamental ideas, as well as the state-of-the-art and current trends in passive radiative cooling, and describes the cutting-edge materials and various photonic radiator structures that are useful in enhancing net cooling performance. This work also addresses a novel skylight window that offers passive cooling developed at the Åbo Akademi (ÅA) University, Finland. In conclusion, nanomaterials and nanoparticle-based coatings are preferred over all other approaches for commercialization in the future because of their low cost, the ability for large-scale production, simplicity in fabrication, and great potential for further increasing cooling performance.

Nanoclay-Incorporated Polycaprolactone Matrix via Electrospinning Techniques-Enriched Spectroscopic Responses

Nanotechnology is one of the most common areas for current research and development in almost all technological fields. A significant factor is the synergistic benefit of nanoscale dimensions over larger scale alteration. Polymer nanoscience is the analysis and application of nanotechnology to polymer nanoparticle matrices, with nanoparticles described as those with at least one dimension of less than 100 nm. The use of polymer nanotechnology and nanocomposites in practical applications is a rapidly developing area. For making polymeric nanofibers from polymer melts and solutions, a spinning technique is used known as electrospinning. Electrospinning is an easy way to produce ultrafine fibers, which is nanosize. For its wide range of variety of spinning polymeric fibers, it is recommended, as well as producing fibers in nanosize accurately. The aim of this project is to use electrospinning to make nanoclay integrated polycaprolactone membranes. The effects of the nanoclay on morphology, thermal, and sorption behaviors of the electrospun membrane were further studied. The scope of this project work is that the electrospun nanocomposites are best studied for biomedical applications. Because of their influence over porosity, pore size, and fiber diameter, they make excellent scaffold materials.

Gold Nanoparticles Immobilized in Porous Aromatic Frameworks with Abundant Metal Anchoring Sites as Heterogeneous Nanocatalysts.

Porous aromatic frameworks (PAFs) with rich metal coordination sites are highly effective support materials for gold nanoparticles (AuNPs), which would not only prevent AuNPs agglomeration but also facilitate mass transfer during the catalytic process. In this work, PAF-160, -161, and -162 bearing diphosphine units are synthesized via the Friedel-Crafts alkylation reaction to act as efficient platforms for AuNPs immobilization. These PAFs possess high surface areas (up to 655 m2 g-1) together with excellent stabilities, and the different linkage lengths between P centers allow more scattered and accessible sites for gold coordination. In the resultant Au-PAFs, AuNPs with uniform sizes are stabilized dispersedly. The catalytic performances of these Au-PAFs are monitored by the reduction of 4-nitrophenol (4-NP), and all materials exhibit excellent catalytic activities on the reduction of 4-NP, especially Au-PAF-162 with the apparent rate constant (kapp) up to 0.019 s-1. Additionally, the reductions of various nitroarenes with different functional groups are explored and all Au-PAFs can convert most nitroaromatic derivatives to the corresponding arylamines with high conversions of 99%, in which the reaction mechanism is also proposed. Furthermore, a continuous catalytic device with Au-PAF-160 catalyst is explored, and Au-PAF-160 can convert 1-chloro-4-nitrobenzene, 2,6-dichoronitrobenzene and 1-chloro-2,4-dinitrobenzene into the corresponding amines in sequence in the continuous flow catalytic experiments. This work has enriched the variety of porous materials for noble metal immobilization and promotes their applications in heterogeneous catalysis.

Flexible and Robust Triboelectric Nanogenerators with Chemically Prepared Metal Electrodes and a Plastic Contact Interface Based on Low-Cost Pressure-Sensitive Adhesive.

Triboelectric nanogenerators (TENGs) are devices that can harvest energy from mechanical motions; such devices can be used to power wearable sensors and various low-power electronics. To increase the lifetime of the device, scientists mainly use the method of making TENG in a hard skeleton to simplify the complex possible relative movements between two triboelectric parts. However, the hard skeletons cannot be embedded in soft and lightweight clothing. To make matters worse, the materials used in the garments must be able to withstand high mechanical forces when worn, such as the pressure of more than 100 KPa exerted by body pressure or everyday knocks. Notably, the TENGs are usually made of fragile materials, such as vacuum-evaporated metal electrodes and nano-sized coatings, on the contact interface; these electrodes and coatings often chip or wear off under the action of external loads. In this work, we succeeded in creating a thin, light-weight, but extremely robust garment-integrated triboelectric nanogenerator (G-TENG) that can be embedded in clothing and pass the water wash test. First, we chemically deposited a durable electrode with flexible properties for G-TENG using a novel technique called polymer-assisted metal deposition (PAMD). The as-formed metal electrodes are firmly bonded to the plastic substrate by a sub-10 nm adhesive polymer brush and can withstand a pressure of 22.5 MPa and a tear force of 0.7 MPa. We then removed the traditionally used fragile nanoparticle materials and the non-durable poly-dimethylsiloxane (PDMS) layer at the triboelectric interface, and then used a cost-effective, durable and slightly flowable pressure-sensitive adhesive to form a plastic contact interface. Such a soft plastic interface can ensure full contact of the triboelectric materials, which is excellent in complex environments and ultimately improves the power generation efficiency of the devices. The as-formed low-cost energy harvesting device could become an industry standard for future smart clothing.

Quantum Dot–Organic Molecule Conjugates as Hosts for Photogenerated Spin Qubit Pairs

The inherent spin polarization present in photogenerated spin-correlated radical pairs makes them promising candidates for quantum computing and quantum sensing applications. The spin states of these systems can be probed and manipulated with microwave pulses using electron paramagnetic resonance spectrometers. However, to date, there are no reports on magnetic resonance-based spin measurements of photogenerated spin-correlated radical pairs hosted on quantum dots. In the current work, we prepare dye molecule-inorganic quantum dot conjugates and show that they can produce photogenerated spin-polarized states. The dye molecule, D131, is chosen for its ability to undergo efficient charge separation, and the nanoparticle materials, ZnO quantum dots, are chosen for their promising spin properties. Transient and steady state optical spectroscopy performed on ZnO quantum dot-D131 conjugates shows that reversible photogenerated charge separation is occurring. Transient and pulsed electron paramagnetic resonance experiments are then performed on the photogenerated radical pair, which demonstrate that (1) the radical pair is polarized at moderate temperatures and well modeled by existing theories and (2) the spin states can be accessed and manipulated with microwave pulses. This work opens the door to a new class of promising qubit materials that can be photogenerated in polarized states and hosted by highly tailorable inorganic nanoparticles.

Self-Assembling Systems for Optical Out-of-Plane Coupling Devices.

Micromirrors are used in integrated photonics to couple extraplanar light into the planar structure of a device by redirecting light via specular reflection. Compared with grating or prism-based couplers, micromirrors allow for coupling of light over a broader range of wavelengths, provided that the micromirror is fabricated with a specific 3D shape to ensure proper reflection angles. In principle, self-assembly methods could enable reliable, parallelizable fabrication of such devices with a high degree of precision by designing self-assembling components that produce the desired microscale geometry as their thermodynamic products. In this work, we use DNA-functionalized nanoparticles to assemble faceted crystallites with predetermined crystal shapes, and demonstrate with microscale retroreflectance measurements that these self-assembled nanoparticle arrays do indeed behave like optically flat mirrors. Furthermore, we show that the tilt angle of the micromirrors can be intentionally controlled by altering the crystallographic symmetry and preferred crystal orientations as a function of the self-assembly process, thereby altering the resulting specular angle in a programmable manner. Measurements of optical coupling from normal incidence into the substrate plane via an optical fiber confirm that the faceted structures can function as optical out-of-plane coupling devices, and coating these structures with reflective materials allows for high efficiency of light reflection in addition to the angular control. Together, these experiments demonstrate how self-assembled nanoparticle materials can be used to generate optically relevant architectures, enabling a significant step in the development of self-assembly as a materials fabrication tool for integrated optical devices.

Lipid Nanoparticle and Liposome Reference Materials: Assessment of Size Homogeneity and Long-Term -70 °C and 4 °C Storage Stability.

With recent advances and anticipated proliferation of lipid nanoparticle (LNP)-delivered vaccines and therapeutics, there is a need for the availability of internationally recognized reference materials of LNP systems. Accordingly, we developed six LNP and liposome (anionic, neutral, and cationic each) candidate reference material formulations and thoroughly characterized by dynamic light scattering their particle hydrodynamic size (Z-avr) and polydispersity. We also evaluated the particle size homogeneity and long-term -70 °C and 4 °C storage stability using multiple large sets of randomly selected vials for each formulation. The formulations stored at -70 °C remained stable and homogeneous for a minimum of 9 months. The Z-avr relative combined uncertainty and the long-term variability were both <1.3% for liposome formulations and anionic LNPs, (3.9% and 1.7%) for neutral LNPs, and (6.7% and 4.4%) for cationic LNPs. An inadvertent few-hour-long storage temperature increase to -35 °C due to a freezer malfunction resulted in a small change of the size and size distribution of anionic liposomes and LNPs but, unexpectedly, a larger size increase of the neutral and cationic liposomes (≤5%) and LNPs (≤25%). The mean Z-avr values of the LNPs stored at 4 °C appeared to slowly increase with t1/3, where t is the storage time, and the Z-avr between-vial heterogeneity and mean polydispersity index values appeared to decrease; no change was observed for liposomes. The size and size distribution evolution of LNPs stored at 4 °C was attributed to an incomplete equilibration of the formulations following the addition of sucrose prior to the initial freezing. Such a process of size increase and size distribution narrowing has not been previously discussed nor observed in the context of LNPs.

In-vivo time course of organ uptake and blood-brain-barrier permeation of poly(L-lactide) and poly(perfluorodecyl acrylate) nanoparticles with different surface properties in unharmed and brain-traumatized rats.

Traumatic brain injury (TBI) has a dramatic impact on mortality and quality of life and the development of effective treatment strategies is of great socio-economic relevance. A growing interest exists in using polymeric nanoparticles (NPs) as carriers across the blood-brain barrier (BBB) for potentially effective drugs in TBI. However, the effect of NP material and type of surfactant on their distribution within organs, the amount of the administrated dose that reaches the brain parenchyma in areas with intact and opened BBB after trauma, and a possible elicited inflammatory response are still to be clarified. The organ distribution, BBB permeation and eventual inflammatory activation of polysorbate-80 (Tw80) and sodiumdodecylsulfate (SDS) stabilized poly(L-lactide) (PLLA) and poly(perfluorodecyl acrylate) (PFDL) nanoparticles were evaluated in rats after intravenous administration. The NP uptake into the brain was assessed under intact conditions and after controlled cortical impact (CCI). A significantly higher NP uptake at 4 and 24 h after injection was observed in the liver and spleen, followed by the brain and kidney, with minimal concentrations in the lungs and heart for all NPs. A significant increase of NP uptake at 4 and 24 h after CCI was observed within the traumatized hemisphere, especially in the perilesional area, but NPs were still found in areas away from the injury site and the contralateral hemisphere. NPs were internalized in brain capillary endothelial cells, neurons, astrocytes, and microglia. Immunohistochemical staining against GFAP, Iba1, TNFα, and IL1β demonstrated no glial activation or neuroinflammatory changes. Tw80 and SDS coated biodegradable PLLA and non-biodegradable PFDL NPs reach the brain parenchyma with and without compromised BBB by TBI, even though a high amount of NPs are retained in the liver and spleen. No inflammatory reaction is elicited by these NPs within 24 h after injection. Thus, these NPs could be considered as potentially effective carriers or markers of newly developed drugs with low or even no BBB permeation.

Field-synergy and nanoparticle’s diameter analysis on circular jet impingement using three oxide–water-based nanofluids

The field synergy study is carried out using three oxide nanofluids impinging circular jet on the horizontal circular disc to analyse the synergetic interaction of cooling processes between temperature and flows fields. The h eat transfer effect o f the nanofluid is examined by rising the Reynolds number and the nanoparticle concentration depending on field synergy number. For jet impinged cooling process, the scale of synergy between the nanofluid flow speed and temperature is decayed with the increase of Reynolds number. Hence, it is contributed to a lower heat transfer efficiency of the nanofluid. Whe reas, the scale of synergy between the nanofluid flow speed and temperature can be enhanced by rising the particle concentration. Thus, the heat transfer efficiency of the nanofluid is increased. Analysis showed that Al2O3 nanofluid has the maximum relative field synergy among selected three oxide nanofluids. It is evident that the nanoparticle concentration, nanoparticle material and Reynolds number have significant effect on the heat transfer augmentation. In addition, the study is explored by varying jet-disk spacing. Moreover, the investigation has shown that the reducing heat transfer effect for the materials is Al2O3, CuO and TiO2 subsequently. It is revealed that the heat enhancement is higher for smaller nanoparticle’s diameter (i.e., 20 nm) than bigger nanoparticle’s diameter (i.e., 80 nm) of the same material.

Potential Oral Anticancer Therapeutic Agents of Hexahydrocurcumin-Encapsulated Chitosan Nanoparticles against MDA-MB-231 Breast Cancer Cells.

Hexahydrocurcumin-encapsulated chitosan nanoparticles (HHC-CS-NPs) were formulated by oil-in-water emulsification and ionotropic gelation and optimized using the Box-Behnken design. The particle size, zeta potential, and encapsulation efficiency of the optimized HHC-CS-NPs were 256 ± 14 nm, 27.3 ± 0.7 mV, and 90.6 ± 1.7%, respectively. The TEM analysis showed a spherical shape and a dense structure with a narrow size distribution. The FT-IR analysis indicated no chemical interaction between the excipients and the drugs in the nanoparticles, but the existence of the drugs was molecularly dispersed in the nanoparticle matrices. The drug release profile showed a preliminary burst release followed by a sustained release under simulated gastrointestinal (GI) and physiological conditions. A stability study suggested that the HHC-CS-NPs were stable under UV light, simulated GI, and body fluids. The in vitro bioaccessibility and bioavailability of the HHC-CS-NPs were 2.2 and 6.1 times higher than those of the HHC solution, respectively. The in vitro evaluation of the antioxidant, anti-inflammatory, and cytotoxic effects of the optimized HHC-CS-NPs demonstrated that the CS-NPs significantly improved the biological activities of HHC in radical scavenging, hemolysis protection activity, anti-protein denaturation, and cytotoxicity against MDA-MB-231 breast cancer cells. Western blot analysis showed that the apoptotic protein expression of Bax, cytochrome C, caspase-3, and caspase-9, were significantly up-regulated, whereas the anti-apoptotic protein Bcl-2 expression was down-regulated in the HHC-CS-NP-treated cells. Our findings suggest that the optimized HHC-CS-NPs can be further developed as an efficient oral treatment for breast cancer.

Natural Biopolymers as Smart Coating Materials of Mesoporous Silica Nanoparticles for Drug Delivery.

In recent years, the functionalization of mesoporous silica nanoparticles (MSNs) with different types of responsive pore gatekeepers have shown great potential for the formulation of drug delivery systems (DDS) with minimal premature leakage and site-specific controlled release. New nanotechnological approaches have been developed with the objective of utilizing natural biopolymers as smart materials in drug delivery applications. Natural biopolymers are sensitive to various physicochemical and biological stimuli and are endowed with intrinsic biodegradability, biocompatibility, and low immunogenicity. Their use as biocompatible smart coatings has extensively been investigated in the last few years. This review summarizes the MSNs coating procedures with natural polysaccharides and protein-based biopolymers, focusing on their application as responsive materials to endogenous stimuli. Biopolymer-coated MSNs, which conjugate the nanocarrier features of mesoporous silica with the biocompatibility and controlled delivery provided by natural coatings, have shown promising therapeutic outcomes and the potential to emerge as valuable candidates for the selective treatment of various diseases.

Passive, active and endogenous organ-targeted lipid and polymer nanoparticles for delivery of genetic drugs.

Genetic drugs based on nucleic acid biomolecules are a rapidly emerging class of medicines that directly reprogramme the central dogma of biology to prevent and treat disease. However, multiple biological barriers normally impedethe intracellular delivery of nucleic acids, necessitating the use of a delivery system. Lipid and polymer nanoparticles represent leading approaches for the clinical translation of genetic drugs. These systems circumnavigate biological barriers and facilitate the intracellular delivery of nucleic acids in the correct cells of the target organ using passive, active and endogenous targeting mechanisms. In this Review, we highlight the constituent materials of these advanced nanoparticles, their nucleic acid cargoes and how they journey through the body. We discuss targeting principles for liver delivery, as it is the organ most successfully targeted by intravenously administered nanoparticles to date, followed by the expansion of these concepts to extrahepatic (non-liver) delivery. Ultimately, this Review connects emerging materials and biological insights playing key roles in targeting specific organs and cells in vivo.

Carbon-Shielded Selenium-Rich Trimetallic Selenides as Advanced Electrode Material for Durable Li-Ion Batteries and Supercapacitors.

In order to achieve a sustainable future, researchers must continue to research improved electrode materials. Considering the high electronic conductivity, versatile redox activity, and enhanced energy storage performance, nanostructures have been employed as a novel electrode material for high-performance lithium-ion batteries (LIBs) and supercapacitors. Herein, carbon-coated selenium-rich trimetallic selenide (Cu2 NiSnSe4 @C) nanoparticles (NPs) as an efficient electrode material in energy storage devices are prepared. The prepared core-shell Cu2 NiSnSe4 @C NPs electrode is employed as ananode material for LIBs, which demonstrated a high reversible specific capacity of 988.46mA h g-1 over 100 cycles at 0.1 A g-1 with good rate capability. Additionally, the core-shell Cu2 NiSnSe4 @C NPs electrode exhibited an outstanding capacity of 202.5mA h g-1 at 5 A g-1 even after 10 000 cycles. Exploiting the synergistic characteristics, the core-shell Cu2 NiSnSe4 @C NPs material is also investigated as a battery-type electrode for hybrid supercapacitors. The assembled hybrid supercapacitor with Cu2 NiSnSe4 @C NPs and activated carbon showed excellent rate capability including high power (5597.77W kg-1 ) and energy (64.26Wh kg-1 ) densities. Considering the simple synthesis and enhanced energy storage properties, carbon-coated selenium-rich trimetallic selenide can be used as a durable electrode material for practical energy storage devices.

Simulation of Thin-Film Cells With a Multiscale Quantum-Mechanical/Electromagnetic Method

This paper studies the surface plasmon-enhanced effect of metal nanoparticles (NPs) in thin-film cells by using a semi-classical multiscale quantum-mechanical/electromagnetic (QM/EM) method. The QM/EM method establishes a relationship between classical electromagnetic environment and full quantum-mechanical photovoltaics with quantized vector magnetic potential on the boundary. In our theoretical framework, the EM region is solved by Maxwell equation with method of moments (MoM), and the QM region is solved by density-functional tight-binding (DFTB) theory with the nonequilibrium Green's function. The proposed method has predicted that metal NPs could generate surface plasmon enhancement and substantially improve the photovoltaic performance of thin-film cells. By comparison, we investigated the influences of different NP materials, distributions and drop-casting ratios on the current-voltage characteristics. The simulated results provide a comprehensive understanding of photoelectric interaction, which can be utilized to improve the power conversion efficiency (PCE) of thin-film cells by fast optimization design.

Transfer-based nuclear magnetic resonance uncovers unique mechanisms for protein-polymer and protein-nanoparticle binding behavior.

Nanoparticle-based drug delivery systems have shown increasing popularity as a means to improve patient outcomes by improving the effectiveness of active pharmaceutical ingredients (APIs). Similarly, nanoparticles have shown success in targeting alternative routes of API administration, such as applying mucoadhesion or mucopenetration to mucosal drug delivery to enhance uptake. While there are many promising examples of mucoadhesive nanomedicines in literature, there are also many examples of contradictory mucoadhesive binding behavior, most prominently in cases using the same nanoparticle materials. We have uncovered mechanistic insights in polymer-protein binding systems using nOe transfer-based NMR and sought to leverage them to explore nanoparticle-protein interactions. We tested several polymer-coated nanoparticles and micellar polymer nanoparticles and evaluated their binding with mucin proteins. We uncovered that the composition and interaction intimacy of polymer moieties that promote mucin binding change when the polymers are incorporated onto nanoparticle surfaces compared to polymer in solution. This change from solution state to nanoparticle coating can enable switching of behavior of these materials from inert to binding, as we observed in polyvinyl pyrrolidone. We also found the nanoparticle core was influential in determining the binding fate of polymer materials, whereas the nanoparticle size did not possess a clear correlation in the ranges we tested (60-270 nm). These experiments demonstrate that identical polymers may switch their binding behavior to mucin as a function of conformational changes that are induced by incorporating the polymers onto the surface of nanoparticles. These NMR-derived insights could be further leveraged to optimize nanoparticle formulations and guide polymer-mediated mucoadhesion.

Dextran-coated Fe3 O4 Nanoparticles for Hyperthermia Therapy Application

In the present work, nanocrystals of magnetite were prepared by alkaline precipitation. The precursor used for synthesis was ferrous chloride only and the reaction was carried out in absence of any oxidant. Dextran is a material with excellent biocompatibility, water solubility and low cytotoxicity. Hence it was chosen as a potential coating material for the magnetic nanoparticles (MNPs). Both bare and coated MNPs (Fe3O4 and D- Fe3O4) showed particle size of diameter 20.8±4.1 nm and 16.3±3.2 nm, respectively. The magnetization values of both the MNPs were 53.62 emu/g and 47.86 emu/g at room temperature, respectively. The negligible coercivity and remanence values at room temperature implied superparamagnetic behaviour of the MNPs. Zeta potential of both bare and coated nanoparticles showed higher colloidal stability of coated nanoparticles than the bare one at a pH range of 2-10. The MNPs are studied for their heating induction abilities at 167.6 Oe, 251.4 Oe and 335.2 Oe (equivalent to 13.3, 20.0 and 26.7 kA m-1, respectively), in order to use them in magnetic fluid hyperthermia therapy. At 335.2 Oe, DFe 3O4 showed maximum Specific Absorption Rate (SAR) of 120.25 W/g, while bare MNPs showed SAR of 79.32 W/g. Both the particles had no cytotoxic effect on L929 cell line showing their strong possibility to be used for in vivo applications. The further work is in the process.

Next-generation materials for RNA-lipid nanoparticles: lyophilization and targeted transfection.

RNA, including mRNA, siRNA and miRNA, is part of a new class of patient treatments that prevent and treat several diseases. As an alternative to DNA therapy using plasmid DNA, RNA functions in the cellular cytosol, avoiding the potential risks of insertion into patient genomes. RNA drugs, including mRNA vaccines, need carrier materials for delivery into the patient's body. Several delivery carriers of mRNA, such as cationic polymers, lipoplexes, lipid-polymer nanoparticles and lipid nanoparticles (LNPs), have been investigated. For clinical applications, one of the most commonly selected types of RNA delivery carrier is LNPs, which are typically formed with (a) ionizable lipids, which bind to RNA; (b) cholesterol for stabilization; (c) phospholipids to form the LNPs; and (d) polyethylene glycol-conjugated lipids to prevent aggregation and provide stealth characteristics. Most RNA-LNP research has been devoted to achieving highly efficient RNA expression in vitro and in vivo. It is also necessary to study the extended storage of RNA-LNPs under mild conditions. One of the most efficient methods to store RNA-LNPs for a long time is to prepare freeze-dried (lyophilized) RNA-LNPs. Future research should include investigating LNP materials for the development of freeze-dried RNA-LNPs using optimal lipid components and compositions with optimal cryoprotectants. Furthermore, the development of sophisticated RNA-LNP materials for targeted transfection into specific tissues, organs or cells will be a future direction in the development RNA therapeutics. We will discuss the prospects for the development of next-generation RNA-LNP materials.

Superparamagnetic Iron Oxide Nanoparticles [SPION] and its Diversified Applications in the Medical Field: A Mini-Review

Late 21st century, extensive research has been carried out on nanoparticles due to their significant role in a supercapacitor, energy storage, sensing, catalysis, green gas production, and photocatalysis due to their semiconductor behavior, costeffective and simple methodology. The utilization of nanoparticle (NP) material provides numerous advantages in biomedical applications due to its unique properties. Superparamagnetic iron oxide nanoparticles (SPIONs) have been recognized in numerous fields including nanobiotechnology, biomedical engineering, and many other fields for their inestimable applications. Superparamagnetic properties and the smaller size of SPIONs are the major reasons for its utilization in various fields. In this study, we focused on different roots to synthesize the ION Super Paramagnetic Iron oxide nanoparticles (SPION), and biomedical applications due to their non-toxic in biological systems.

Challenges and opportunities for SERS in the infrared: materials and methods.

In the wake of a global, heightened interest towards biomarker and disease detection prompted by the SARS-CoV-2 pandemic, surface enhanced Raman spectroscopy (SERS) positions itself again at the forefront of biosensing innovation. But is it ready to move from the laboratory to the clinic? This review presents the challenges associated with the application of SERS to the biomedical field, and thus, to the use of excitation sources in the near infrared, where biological windows allow for cell and through-tissue measurements. Two main tackling strategies will be discussed: (1) acting on the design of the enhancing substrate, which includes manipulation of nanoparticle shape, material, and supramolecular architecture, and (2) acting on the spectral collection set-up. A final perspective highlights the upcoming scientific and technological bets that need to be won in order for SERS to stably transition from benchtop to bedside.