NaCl Solution Research Articles

Impact of decontamination and processing methods on insecticide residues in green and red chilli (Capsicum annum L.) by LC- MS/MS

The study aimed to evaluate various decontamination and processing methods for the removal of pesticide residues in chilli, focusing on emamectin benzoate, fipronil, spirotetramat, and tolfenpyrad. The LC-MS/MS instrument parameters were standardized and method was validated for identification and quantification of residues in both green and dry chilli. In green chilli, treatments such as soaking in 2 per cent NaCl solution showed promising results in reducing pesticide residues. The tested decontamination treatments are effective for handling emamectin benzoate and tolfenpyrad residues in green chilli. However, fipronil residues remained above Maximum Residual Limits even after decontamination treatments, indicating the need for careful application and monitoring. In red chilli, processing methods such as sun-drying and pan-frying led to increased residues due to concentration effects during drying. Despite efforts, some residues remained above regulatory limits, emphasizing the importance of adhering to pre-harvest intervals to minimize residues in processed chili products.

Serotonin and adrenaline as inhibitors of neutrophil extracellular traps formation (experimental study)

Regulation of the NETosis can provoke cancer, inflammatory and autoimmune diseases and become a basis for effective targeted therapy. The aim: to study the modifying effects of serotonin and adrenaline on NETosis during phagocytosis in rats.Materials and methods.Wistar rats were divided into control (solvent, 0.9% NaCl solution) and experimental (serotonin and adrenaline 1.43 and 0.143 mg/kg body weight, respectively) groups. Intraperitoneal injection of test substances was carried out 90 minutes before blood sampling, in which phagocytic activity (PhA), phagocytic index (PhI) and degree of suicidal neutrophil NETosis were determined: with total and partial chromatin decondensation (TCD, PCD, accordingly). A paired Student’s t test was used to compare groups with numerical values and McNemar’s test (for dichotomous variables). Pearson’s linear correlation coefficient (rxy) was assessed to measure a linear relationship between time points.Results.The administration of adrenaline contributed to NETosis inhibition by 41.5% compared to control group (p 0.001), serotonin — by 27.6% (p 0.001). The ratio of neutrophils with total and partial chromatin decondensation for control group was 1.0:0.9; for serotonin and adrenaline it changed to 1.0:1.7 and 1.0:1.4, respectively. Relative to control group, phagocytic index after serotonin administration increased by 4.9%, in case of adrenaline, on the contrary, it decreased by 12.4% (p 0.01). A high positive correlation was revealed between NETosis and phagocytic index for control group and experimental group with adrenaline: rxy= 0.823–0.997. For phagocytic index and NETosis in these groups there was a high negative (rxy= –0.714–(–0.871)) and a noticeable positive correlation for serotonin (rxy= 0.638).Conclusion.Serotonin and adrenaline in therapeutic dosages have a pronounced inhibitory effect on NETosis, which may pave the avenue for increasing the effectiveness of therapy for immunoinflammatory and oncological diseases. The use of serotonin is preferable because it has additional immunomodulatory effects and cause no direct stimulation ofα- andβ-adrenergic receptors.

ЦИНКНАПОЛНЕННЫЕ ПОКРЫТИЯ ДЛЯ ЗАЩИТЫ СЕЛЬСКОХОЗЯЙСТВЕННОЙ ТЕХНИКИ ОТ АТМОСФЕРНОЙ КОРРОЗИИ

Application of zinc-filled coatings (ZFC) on oil base is possible for protection of agricultural machinery from atmospheric corrosion. Analysis of literature has shown that anti-corrosion efficiency of ZFC largely depends on the size of zinc particles included in their composition. Zinc powders of different sizes PCR-1 (up to 40 μm) and PC-1 (up to 9 μm) in the amount of 40-60 wt.% were used for research. Oils were used: used motor oil (MMO), industrial oil I-20A, refined rapeseed oil and drying oil were used as a binder. It was determined that the corrosion potential (Ecor) of St3 steel with ZFC in 0.5 M NaCl solution occupies an intermediate value between the Ecor of steel and the Ecor of compact zinc. The concentration of Zn in the oil film as a result of its oxidation and transition to 0.5 M NaCl solution decreases over time from 40-60%, reaching almost the minimum value after 20 days. It was found that the introduction of zinc powder into oils increases their protective efficiency (Z) the more significantly, the smaller the particle size. The introduction of 40% PCR-1 powder increases Z MMO by 5%, and zinc PC-1 - by 48% in a saline solution. These trends are also preserved during tests in the G-4 heat and moisture chamber, but the difference when using different CNP is not as significant as during tests in a saline solution. The maximum Z = 93% was obtained for drying oil with 50% PCR-1; Z = 94- 95% for compositions with 50-60 wt.% PC-1 in rapeseed oil, Z = 94-95%. Coatings with PC-1 in MMO and rapeseed oil provide Z = 91% during full-scale bench tests over 12 months.

Microstructure and Corrosion Resistance of 7075 Aluminium Alloy Composite Material Obtained from Chips in the High-Energy Ball Milling Process.

The high-energy ball milling process was applied to fabricate a composite material from 7075 aluminium alloy milling chips, silicon carbide, and titanium dioxide powders. Raw materials were ground, and the obtained powders were cold pressed and sintered. It was demonstrated that this method can be used in the recycling of aluminium alloy scrap characterised by a high surface-to-volume ratio, and also that chemical removal of the oxide layer from chips is not necessary. The finest particles, with 50 vol.% of their population below 36 μm, were obtained after grinding for 60 min at a 1000 rpm rotational speed. Such an intensive grinding was necessary to fabricate the compact composite material with a homogeneous microstructure and a low porosity of 0.7%. The corrosion resistance of the composites was studied in 3.5 wt.% NaCl solution using cyclic voltammetry and electrochemical impedance spectroscopy, and corrosion rates in the range of ca. 342 and 3 μA∙cm-2 were obtained. The corrosion mechanism includes aluminium alloy dissolution at the matrix/reinforcement interphase and around intermetallic particles localised within the matrix grains.

Preparation of Chromium Carbide-Strengthened Ni-W Coatings by Electrodeposition and the Corresponding Anticorrosion Behavior in CO2-Saturated NaCl Solution

In this study, we have prepared Ni-W/Cr3C2 composite electrodeposits through the diffuse reinforcement mechanism of chromium carbide nanoparticles. These electrodeposits exhibit excellent corrosion resistance and are designed to effectively protect the structural materials of pipe columns under the harsh CO2 corrosion environments faced by carbon sequestration and utilization technologies. A systematic investigation was conducted into the micro-morphology, profile undulation, phase composition, and surface chemical state of the electrodeposits. Furthermore, the corrosion-resistant behavior of Ni-W/Cr3C2 composite electrodeposits was investigated in simulated corrosive environments (i.e., brine solution containing 3.5 wt% NaCl and CO2-saturated brine). We then evaluated their corrosion response under the aforementioned conditions using electrochemical methods. In addition, the EIS of electrodeposited coatings revealed that the dense oxide film layer formed on the surface of the deposits, which acted as a primary barrier against corrosion, playing a pivotal role in maintaining the overall corrosion resistance of the material.

Selective separation of dyes and tetracycline hydrochloride in polymer‐nucleotide coacervate droplets

AbstractThis paper reports the formation of coacervates by the electrostatic interaction of poly (diallyldimethylammonium chloride) (PDDA) and adenosine triphosphate (ATP) in aqueous solution, examining its formation conditions, stability, and efficiency in separation. The ideal concentration for creating coacervate droplets in pure water, HEPES buffer, and NaCl solution was determined to be 20 mM of PDDA and ATP. Enhancing the stability of coacervates was achieved by incorporating phospholipid vesicles on their surface, presenting a novel strategy for building cell models. Ostwald Ripening was employed to comprehend the growth mechanism of the coacervates, while the Hofmeister Ion Series and Schulze‐Hardy's rule were utilized to elucidate the stability differences in solutions containing NaCl, Na2SO4, and MgCl2. These coacervates were stable at concentrations below 90 mM NaCl, 200 mM Na2SO4, and 30 mM MgCl2, respectively. We also explored the specific separation of dyes and tetracycline hydrochloride (TC) in the coacervates. Separation efficiencies of 92.98% for methylene blue (MB), 94.19% for methyl orange (MO), and 85.94% for TC, were achieved by the coacervates, which can be attributed to the synergistic effects of hydrophobicity, electrostatic forces, and π‐π interactions. The proposed coacervates have great potential in cell mimicry and water treatment.

Effects of molybdenum and cobalt alloying on corrosion resistance of electrochemical coatings based on the Ni–W system

The paper studies coatings of the Ni–W system alloyed with molybdenum and cobalt obtained by electrodeposition. The effect of the concentration of salts of the alloying element in the electrolyte on the chemical composition of the coatings was studied under various synthesis conditions. All the obtained coatings are nanocrystalline or amorphous solid solutions of tungsten, molybdenum or cobalt in nickel with a FCC crystal lattice. Polarization measurements made it possible to establish that the most resistant to corrosion in a 3.5% NaCl solution is a coating containing 35% W and 8% Mo.

Optimizing the surface quality of electrochemical machined Ni-based single crystal superalloy via manipulation of phase and dendrite dissolution

The transpassive dissolution behaviors of Ni-based single crystal superalloy in 10 %NaCl, 10 %NaNO3, and mixed solution are investigated by using potentiodynamic polarization, scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy. The alloy exhibits opposite yet complementary dissolution characteristics in NaCl and NaNO3 solutions. The different responses of γ/γ′ phases to Cl− and NO3− contribute to the opposite dissolution behaviors of dendrites and interdendritic regions. The surface flatness is noticeably enhanced in mixed solution due to the synchronous dissolution of the γ/γ′ phases. Our work paves the way for obtaining high-quality surface in electrochemical machining of single crystal superalloys.

Phase, Microstructure and Corrosion Behaviour of Al0.3FeCoNiCrx High-Entropy Alloys via Cr Addition.

The microstructure evolution of Al0.3FeCoNiCrx (x = 0, 0.3, 0.5, 1, 1.5) high-entropy alloys (HEAs) were studied using X-Ray diffraction technique and scanning electron microscope equipped with energy dispersive spectrometer. The short-term and long-term corrosion behaviours of these alloys in 3.5 wt.% NaCl solution were studied by electrochemical impedance spectroscopy, potentiodynamic polarisation measurement, immersion test and corrosion morphology analysis. The results show that all the designed HEAs present single-phase FCC structure, and the increase in Cr content changes the microstructural morphology from cellular to a typical dendritic-interdendritic state. Without the influence of phase transformation, the corrosion resistance of Al0.3FeCoNiCrx HEAs gradually increases with the increase in Cr content. Our designed alloys exhibit excellent corrosion resistance compared to the existing HEAs in the AlFeCoNiCr composition system.

Investigation of Structural Phase, Mechanical, and Tribological Characteristics of Layer Gradient Heat-Protective Coatings Obtained by the Detonation Spraying Method.

This paper presents the results of a study of layer gradient thermal protection coatings based on NiCrAlY and YSZ obtained by detonation spraying. Modern gas turbines and high-temperature units operate under extreme temperatures and aggressive environments, which requires effective protection of components from wear, corrosion, and thermal shocks. In this study, the use of layer gradient coatings consisting of alternating layers of NiCrAlY and YSZ was investigated with the aim of solving the problem of thermal stress accumulation due to a smooth change in the composition of the layers. Microstructural and phase analysis showed that alternating layers of NiCrAlY and YSZ formed a dense layer gradient structure with clear interphase boundaries and low porosity. Detonation spraying led to a complete transformation of the monoclinic ZrO2 phase into a tetragonal one, which significantly increased the mechanical strength of the coating and its resistance to thermal shocks. Sample 1D1 demonstrated excellent tribological and corrosion properties in a 3.5% NaCl solution, which can be explained by its higher density and reduced number of pores. Mechanical tests revealed stable values of hardness and wear resistance of the coating, especially for the 1D1 coating. Studies have shown that coatings are resistant to thermal shocks, but thicker layers show a tendency to peel off after thermal cycling. The obtained results indicate high prospects for the use of layer gradient coatings based on NiCrAlY and YSZ for the protection of gas turbine components and other high-temperature installations operating under extreme loads and aggressive environments.

Corrosion studies of Al-Mg-Sc-Zr Alloy with Low Sc/Zr ratio fabricated by laser powder bed fusion for marine environments

This study investigates the corrosion behavior of a laser powder bed fusion (LPBF) Al-Mg-Sc-Zr alloy with a Sc/Zr ratio of less than 1 in 3.5wt% NaCl solution. X-ray diffraction (XRD) analysis revealed the presence of an Al matrix with face-centered cubic (FCC) structure and the secondary phase Al3(Sc,Zr) with L12 crystal structure. Microstructural analysis indicated a bimodal grain size distribution with fine equiaxed and columnar grains influenced by thermal gradients and secondary phase Al3(Sc,Zr). Potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) tests in 3.5wt% NaCl solution demonstrated that the alloy exhibits a less negative corrosion potential (Ecorr) and lower corrosion current density (icorr) compared to other Al-Mg-Sc-Zr alloys with higher Sc/Zr ratios, indicating superior corrosion resistance. The enhanced performance is attributed to the fine grain structure and the formation of a stable protective oxide layer facilitated by the higher Zr content.

Constructing Long and Stable Ag‐Al2O3 Core–Shell Nanowires for Humidity Sensing and Triboelectric Energy Generation

Silver nanowires (AgNWs) are a promising alternative material to indium tin oxide as flexible transparent electrodes owing to their excellent optoelectrical properties and mechanical performance. However, the main challenge is the poor stability under diverse environments, ranging from high humidity, chemical exposure, and dynamic mechanical deformation. Herein, ultralong AgNWs (≈100 μm) have been synthesized via controlling growth kinetics by a facile acetic acid‐assisted solvothermal method, further decorated with a thin Al2O3 layer by electrodeposition to form a core–shell architecture. The resultant films based on Ag‐Al2O3 core–shell nanowires (NWs) possess a higher conductivity while preserving the optical transparency due to the enhanced NWs contact. More importantly, the constructed films exhibit strong resistance to various conditions, such as exposure to high temperature/humidity and immersion in NaCl, HCl, and Na2S solutions. The laser‐etched interdigital electrodes based on the chemically stable AgNWs are further integrated with graphene oxide layer for humidity sensing and respiration monitoring. Furthermore, the developed NWs with superior mechanical stability are constructed as triboelectric nanogenerators for electricity generation, and reliable output performance has been demonstrated. This work provides a convenient, scalable, and cost‐effective solution that offers great potential for designing robust, transparent electrodes for next‐generation flexible electronics.

Corrosion Behavior of High-Pressure Cold-Sprayed Zn30Al Alloy Coating on Q235 Steel

This study employed a high-pressure cold spray to apply a Zn30Al alloy coating to Q235 steel substrates to provide corrosion protection for steel in marine environments. The corrosion resistance of the coatings was investigated through full immersion tests, and the corrosion mechanisms were further analyzed using electrochemical experiments. The results were compared with those of traditional flame-sprayed Zn30Al alloy coating. The findings indicate that the high-pressure cold-sprayed Zn30Al alloy coating possesses a dense microstructure with a porosity of only 0.32%, providing effective cathodic protection to the substrate during the immersion tests. The cold-sprayed Zn30Al alloy coating maintained good integrity after 720 h immersion in 3.5 wt.% NaCl solution, whereas the flame-sprayed Zn30Al alloy coating exhibited significant pitting corrosion.

Effect of Natural Inhibitors on the Corrosion Properties of Grade 2 Titanium Alloy.

This study investigates the effects of natural inhibitors (pomegranate, algae, and tomato extracts) on the corrosion resistance of titanium (grade 2). To deepen understanding the inhibition mechanism, Molecular Dynamic (MD) and Monte Carlo (MC) simulations were employed to analyze adsorption behaviors and identify optimal adsorption sites on titanium oxide (TiO2) surfaces for compounds within the inhibitors. Results indicate non-flat adsorption orientations, with pomegranate peel extract components showing superior inhibition capabilities, attributed to the formation of strong O-H chemical bonds with the TiO2 surface. In the experimental part of the study Electrochemical Impedance Spectroscopy (EIS) and Potentiodynamic Polarization (PDP) were conducted. Two electrolytes were tested: a solution 3.5% NaCl and a solution 0.5 M NaOH. All the tests were performed with 5% of inhibitor and with the reference solution. Also, inhibition efficiency was calculated on the base of PDP tests. The study found that pomegranate extract can act as a good corrosion inhibitor for titanium alloy in aqueous solutions 0.5 M NaOH. This was demonstrated by the increase in the corrosion potential and impedance modulus and decrease in the corrosion current density after the addition of pomegranate extract to the solution. However, in a 3.5% NaCl solution, the efficacy of pomegranate extract was less pronounced, probably due to the high aggressivity of the electrolyte. Tomato and algae extract have instead shown very low inhibition effects in all the tested conditions.

Fast room-temperature and water-insensitive self-healing polyurethane for superior composite anti-corrosion coating on Mg alloys

Self-healing polyurethane is widely applied as the anti-corrosion coating to elongate the durability of substrate. However, it remains great challenge to achieve the rapid self-healing performance at room temperature for polyurethane. And it is even more difficult to accomplish the healing under the water. Herein, a novel self-healing polyurethane, PDMS-SS-Py, is prepared to achieve self-healing within 2 h at room temperature. Even under the water, the 97.1 % self-healing efficiency is kept. Molecular dynamics (MD) simulation and density function theory (DFT) demonstrate that hydrogen bonds are pioneers in the healing process of PDMS-SS-Py and elucidate the critical items to achieve the underwater self-healing. On the basis of PDMS-SS-Py, the composite coating, MAO/8-HQ/P, is fabricated on Mg alloy along with microarc oxidation (MAO) and inhibitor 8-hydroxyquinoline (8-HQ) inserted in the micropores of MAO. The self-healing performance of composite coating is almost the same as that of isolate PDMS-SS-Py. As compared with bare Mg alloy, the impedance modulus at the low frequency (|Z|0.01Hz) is increased by 8 orders of magnitude after covering MAO/8-HQ/P coating. Even after 12 days of immersion in 3.5 wt% NaCl solution, the MAO/8-HQ/P composite coating still maintains superior anti-corrosion performance. The excellent anti-corrosion performance is contributed by the self-healing property of PDMS-SS-Py layer, the active protection of 8-HQ, and the basic protection of MAO. This work provides a general strategy for constructing durable self-healing anti-corrosion coating on Mg alloy and deepens the mechanism of polyurethane repairing processes.

D-Band Center Engineering of Nickel Nanoparticles Accelerates Water Dissociation for Hydrogen Evolution in Neutral NaCl Solution.

While Pt is highly efficient for hydrogen evolution reaction (HER), its widespread use is limited by scarcity and high cost. Herein, a vertically aligned electrocatalyst is present comprising Ni3S2 nanotube arrays (NTAs) and Ni nanoparticles (NPs) (Ni3S2/Ni NTAs) for neutral HER. In a neutral 4 wt.% NaCl solution (pH = 7), the Ni3S2/Ni NTAs achieves a current density of 100mA cm-2 at a low overpotential of 540mV, outperforming both Ni3S2 NTAs and Ni NTAs and even the commercial Pt plate. The hollow tubular structure offers ample mass transfer channels, and strong electronic interaction between Ni3S2 and Ni is observed. Theoretical studies reveal that the lowered d-band center (ɛd) of Ni 3d orbital significantly reduces the activation energy for H2O dissociation and facilitates the movement of an H atom in H2O away from OH to form a transition state, consequently promoting H2 evolution. When Ni3S2/Ni NTAs is used as the cathode in a two-electrode diaphragm-free electrolyzer with a RuSnTi anode, efficient H2 production and energy-saving Cl2 evolution are achieved. This work highlights the potential of uniquely structured electrocatalysts for HER in neutral NaCl solutions.

Effects of salt stress on the fruit and yield quality of some selected tomato (<i>Lycopersicum esculentum</i> L.) varieties.

The growth, production, and nutritional characteristics of crops are impacted by abiotic factors such as salinity stress. The study aimed to assess the impact of salt stress on the fruit and yield characteristics of three distinct tomato cultivars, namely Rio, Dan syria, and UTC. Salt solutions with varying concentrations of NaCl were created by dissolving NaCl in deionized water. Four treatments were established, consisting of solutions with salt concentrations of 0g/L (control, without salt), 0.5g/L, 1.0g/L, and 1.5g/L. Each treatment was reproduced three times. The NaCl solutions were administered with a frequency of 7 days. The data in the study underwent Analysis of Variance (ANOVA). Rio outperformed the other varieties in terms of fruit quantity, fresh fruit weight, and fruit pericarp thickness under high salt stress, closely followed by UTC variety. The study also found that Dan syria performed better than the other varieties in terms of fresh and dry weight of shoot, as well as fresh weight of root, under mild and extreme salinity stress. However, Rio performed better than the other varieties in terms of dry weight of root under both mild and extreme salinity stress. The salt tolerance index of the Rio, UTC, and Dan Syria varieties under extreme salinity stress are 46.79%, 20.64%, and 34.70% respectively. This indicated that the Rio variety is the most salt-tolerant of the three types, with Dan Syria variety coming close.

Isolation, Identification, and Application of Endophytic Fungi from Lavandula stoechas L.: Mitigating Salinity Stress in Hydroponic Winter Cereal Fodder

Soil and irrigation water salinity is a growing global problem affecting farmland, due to poor agricultural practices and climate change, leading to reduced crop yields. Given the limited amount of arable land and the need to boost production, hydroponic systems offer a viable solution. Additionally, endophytic fungi have been shown to mitigate salinity effects through symbiosis with plants. This study evaluated three endophytic fungi isolated from Lavandula stoechas L. in the grasslands of Extremadura (i.e., Diplodia corticola L11, Leptobacillium leptobactrum L15, and Cladosporium cladosporioides L16) for their ability to improve hydroponic forage production under saline conditions. In vitro experiments were conducted assessing plant growth promotion and fungal growth under salinity, followed by research evaluating the impact of fungal inoculation on hydroponic wheat (Triticum aestivum L.) and barley (Hordeum vulgare L.) forages irrigated with NaCl solutions (0, 100, and 200 mM). The results showed improved fungal growth and production of plant growth-promoting substances, which could explain the improved plant germination, shoot and root length, fresh and dry weight, and yield of inoculated plants growing under salinity. Plants inoculated with L15 or L16 showed the best performance overall. L15 demonstrated broader bioactivity in vitro, potentially explaining its superior performance in both wheat and barley growth. Conversely, L16 was more effective in barley, while L11 was beneficial in wheat but detrimental in barley. This study provides a preliminary exploration of the capabilities of these fungi and their optimization for hydroponic forage production.

Corrosion Inhibition of Copper by Pisum sativum Peel Extracts in NaCl Solution: Phytochemical Analysis and DFT Study

Corrosion Inhibition of Copper by Pisum sativum Peel Extracts in NaCl Solution: Phytochemical Analysis and DFT Study

Effect of Chloride Solution on Liquid Limit, and Plasticity Index of Soil in Selected Sites in Erbil /North Iraq

This study is an attempt to investigate the effect of NaCl, CaCl2, KCl, and NH4Cl solutions with different concentrations (2.5%, 5%, 7.5%) on the liquid limit, plastic limit, and plasticity index of Sarbasty and Mamwastayan soil samples /Erbil Governorate. The soil samples' liquid and plastic limits were found by using the cone penetrometer method. The Results showed that the soil's liquid, plastic limits, and Plasticity index decreased with increasing salt solution concentration. Maximum reduction of liquid limit and plastic limit in Sarbasty was from 53.6 to 34.3 and in Mamwastayan from 35.9 to 27.2, both accomplished by adding a concentration of 7.5% of KCl and CaCl2 respectively. According to the Unified Soil Classification System, the Sarbasty soils were classified as high plasticity clay (CH), and Mamwastayan low plasticity clay (CL). After adding different concentrations of salt solution to the soil, the Sarbasty soil classification changed from CH to CL. Mineralogically these soils are composed of non-clay minerals of calcite and quartz and clay minerals consisting of Montmorillonite, Chlorite, swelling Chlorite, Kaolinite, Illite, Palygorskite, and Illite- Chlorite. Sarbasty soil was the most effective salt chloride solution than the Mamwastayan soil sample swelling.