Multiwavelength Erbium-doped Fiber Laser Research Articles

Multi-wavelength Brillouin erbium-doped fiber laser with 40 GHz frequency shift interval assisted by Sagnac loop filter

Multi-wavelength Brillouin erbium-doped fiber laser with 40 GHz frequency shift interval assisted by Sagnac loop filter

Multiwavelength erbium-doped fiber laser using the polarization-hole-burning effect for multichannel acoustic detection.

We propose and demonstrate a novel, to the best of our knowledge, fiber-optic multipoint acoustic detection system based on a multiwavelength erbium-doped fiber (EDF) laser (MWEDFL) using the polarization-hole-burning effect with Fabry-Perot interferometers as the acoustic cavity-loss modulator. A polarization-wavelength-related filter is designed to assign a distinct polarization state to each laser wavelength. By adjusting the polarization state, the polarization-dependent loss and gain of each laser line are tuned to be equal, effectively suppressing the mode competition of EDF and enabling a stable MWEDFL. Each laser line serves as a separate channel for acoustic detection. Theoretical and experimental analyses are conducted to study the transient-response-amplification effect on the acoustic perturbation of the MWEDFL. The results show that the proposed MWEDFL exhibits an amplification effect on the sound-induced cavity-loss modulation, effectively enhancing the sensitivity by 13 dB compared to that obtained using an external-light-source demodulation method. In addition, the MWEDFL based on the PHB effect avoids cross talk between laser channels and can achieve high sensitivity and simultaneous multichannel acoustic detection.

Generation of cylindrical vector beam pulses by using multi-wavelength EDFL with two-mode fiber filter

A multi-wavelength erbium-doped fiber laser (MW-EDFL) operating in the L-band with cylindrical vector beam outputs is proposed and experimentally investigated. The multi-wavelength lasing is realized by exploiting a two-mode fiber filter (TMFF) as the comb filter and a single-mode fiber spool with 2-km in length to suppress the mode competition. The multi-wavelength combs with channel spacing of 0.36 nm, 0.58 nm, and 1.12 nm are achieved by regulating the interference length of the TMFF, and up to 18 lasing channels are obtained with a wavelength spacing of 0.36 nm. Good long-term stability is manifested within a 100-minute duration, as the maximum peak power fluctuation of 1.96 dB and the maximum wavelength shift of 0.03 nm are measured. By adjusting the polarization controller associated with the two-mode long-period grating as a high-efficiency mode converter, radially and azimuthally polarized cylindrical vector beams of high purity are thus generated.

Tunable and switchable multiwavelength fiber laser incorporating tapered few-mode fiber Bragg gratings

A tunable and switchable multiwavelength Erbium-doped fiber laser (MWFL) is proposed and demonstrated based on tapered few-mode fiber Bragg gratings (TFMFBG). Optical modes inside TFMFBG have extensive evanescent tails that are sensitive to changes in the external medium. The MWFL can be tuned in the 1.5 µm wavelength region when temperature and refractive index variations are applied to the TFMFBG. The temperature and refractive index sensitivities range from 11.5 pm/⁰C to 14.6 pm/⁰C and 3.10 nm/RIU to 3.93 nm/RIU, respectively. Additionally, due to the polarization dependency of TFMFBG, single-, dual-, and triple-wavelength lasing lines can be switched within the MWFL cavity. The stable triple-wavelength lasing was generated at peak wavelengths of 1533.04 nm, 1532.35 nm, and 1531.71 nm for λ1, λ2, and λ3, respectively. The developed triple-wavelength laser corresponded to a specific guided mode inside the few-mode FBG, including fundamental LP01 mode, higher-order LP11 mode, and mode coupling between LP01 and LP11 (LP01-LP11).

Switchable multi-wavelength fiber lasers based on asymmetric biconical fiber tapers

In this paper, switchable multi-wavelength erbium-doped fiber lasers (MW-EDFLs) are proposed and experimentally demonstrated. An in-fiber Mach–Zehnder interferometer (IFMZI) composed of asymmetric biconical fiber taper (ABFT) pairs is integrated into the all-fiber ring cavity for multi-wavelength filtering. This laser can stably emit single-, dual-, or triple-wavelength outputs by fine-tuning the polarization controller. A high optical signal to noise ratio of 58.5 dB is obtained for the output spectra. The maximum wavelength shift is 0.08 nm and the power fluctuation in all laser emissions is recorded at 1.64 dB.

A passively Q-switched multi-wavelength erbium-doped fiber laser modulated by 12° tilted fiber Bragg grating

As a promising small-angle TFBG, the 12° tilted fiber Bragg grating (TFBG) has been successfully used in biochemical sensors, fiber optic anemometers, and continuously tunable photon fraction time differentiators. On the other hand, multi-wavelength Q-switched fiber lasers have widely potential and practical applications in various fields, such as laser processing, laser marking, medical diagnosis, military applications, and so on. In this paper, first, a 12° TFBG is prepared by femtosecond laser direct inscription method (FSL-DIM), then, a pulse multi-wavelength erbium-doped fiber laser (EDFL) passively Q-switched by the as-prepared 12° TFBG is exclusively and systematically demonstrated for the first time. When the pump power is raised from 100 mW to 500 mW, the repetition rate is boosted from 51.64 kHz to 149.4 kHz resulting in a repetition rate range about 97.76 kHz, while the pulse duration is compressed from 3.928 μs to 1.033 μs. The average output power monotonically increases up to the maximum value of 6.357 mW corresponding to the maximum pulse energy of 42.55 nJ. The signal-to-noise ratio (SNR) is measured to be 53 dB, which indicates a high stability. The experimental results are comparable to other Q-switched multi-wavelength EDFLs reported so far, and during the experiment, the 12° TFBG exhibits excellent stability and reliability. As far as we can explain, the multi-wavelength Q-switched operation obtained in this paper benefits from the filtering effect and polarization dependent loss (PDL) effect of the 12° TFBG. The work not only provides a reliable reference about the effective-SA performance of 12° TFBG, but also enriches the studies of passively Q-switched lasers based on different kinds of modulators.

A C-band widely tunable and switchable erbium-doped fiber laser based on a Sagnac-like loop embedded in Lyot filter

In this paper, a new type of widely tunable and switchable multi-wavelength erbium-doped fiber laser based on a Sagnac-like loop embedded in Lyot filter is proposed. The nonlinear polarization rotation effect is obtained by adjusting two polarization controllers (PCs). The polarization-dependent isolator and the Sagnac-like loop are used as the basic structure to realize the wide tuning and wavelength switching in C-band. Compared with the traditional Lyot filter, the Sagnac-like loop is used to replace the segment of polarization-maintaining fiber, and a more uniform comb spectrum can be obtained by this filter. The tunable and switchable wavelengths can be achieved by adjusting the PCs based on the nonlinear effect of the loop. The laser can emit single-, dual-, triple-, quad- and quintuple-wavelengths. The optical signal-to-noise ratios all exceed 43 dB. It can also be adjusted to partial wavelength intervals for quad-wavelength and quintuple-wavelength. The tuning range can reach the full range of the C-band, and the laser efficiency can reach the practical application standard. It can be applied to some precision instruments and equipment.

Vernier effect based on hybrid fiber interferometers: a new tool for wavelength switchability and adjustable free spectral range fiber lasing

In optical communications systems, the used filter and/or demultiplexer needs to have a broad free spectral range (FSR) in order to accommodate more channels and have acceptable interchannel crosstalk. The Vernier effect applied to fiber filters is a recent effective tool to enlarge the FSR. Here, by harnessing the Vernier effect of a hybrid interferometer consisting of a Mach–Zehnder interferometer (MZI) and Sagnac interferometer (SI), we proposed and experimentally demonstrated a new kind of comb filter for a switchable and interval adjustable multi-wavelength C-band erbium-doped fiber laser (EDFL) application. In the designed comb filter, the MZI is composed of bi-tapered polarization-maintaining fibers (PMFs) fabricated by fusion splicing and has the function of achieving the switchability of the proposed dual-wavelength EDFL. The SI configured by nesting tapered PMF is employed as a switchable and wavelength-spacing tuning component of triple-wavelength EDFL. In this experiment, the FSR of the MZI and the SI is designed to be close but not equal, which could be achieved by properly adjusting the length of the employed PMF, so the Vernier effect can exist and a comb spectrum with an obvious envelope is obtained. Through the adjustment of the polarization controller (PC1) and (PC2) inside the cavity, a switchable and interval-adjustable multi-wavelength EDFL was achieved. To the best of the authors’ knowledge, this is the first time that an all-fiber hybrid filter based on the Vernier effect has been used to manipulate the spectral output characteristic of an EDFL and achieve a switchable multi-wavelength fiber laser.

Q-switching pulse generation in multi-wavelength Brillouin Erbium-doped Fiber laser

Stimulated Brillouin scattering (SBS) was successfully used to induce Q-switching operation in a multi-wavelength Brillouin Erbium fiber laser (BEFL) operating in a long-wavelength band (L-band) regime. The SBS based self Q-switched laser used a 4.5 long highly nonlinear Erbium-doped fiber (EDF) as the hybrid gain medium to generate a multiple wavelength Q-switched pulses, which operated at the center wavelength of around 1603 nm. By changing the input pump power in a range from 59.1 mW to 162.2 mW, the repetition rate can be varied from 14.29 to 29.69 kHz and the pulse width can be grasped from 26.52 to 14.80 μs. Under 162.2 mW pump power, the maximum pulse energy was recorded at 96.0 nJ and the signal to noise ratio of the fundamental radio frequency was measured to be as high as 52.73 dB, which indicates the excellent stability of the SBS-based Q-switched laser. To the best of our knowledge, this is the first experiment of realizing a BEFL with Q-switched multi-wavelength output without any physical saturable absorber devices.

Flat Multi-Wavelength Brillouin Erbium-Doped Fiber Laser Based on a Sagnac Loop for High-Sensitivity Sensor.

We have demonstrated the use of a flat multi-wavelength Brillouin erbium-doped fiber laser (MWBEFL) based on a Sagnac loop with an unpumped erbium-doped fiber (Un-EDF) as a high-sensitivity sensor. A Sagnac loop with a Un-EDF was used as power equalizer to achieve multi-wavelength power flatness by adjusting the birefringence beat length properly. In the experiments, the best result obtained in terms of Brillouin Stokes lines and output power flatness was ±0.315 dB and the optical signal-to-noise ratio (OSNR) was 18.97 dB within a 33 nm bandwidth range from 1532.0 nm to 1565.0 nm. The flatness of the 33 nm bandwidth range varied from ±0.315 dB to ±1.38 dB and the average OSNR was about 17.51 dB. The peak power values of Brillouin Stokes lines observed under different wavelengths were extremely close and their range of fluctuation was about ±0.37 dB. These experimental results were close to our previous experimental values obtained using a passive Sagnac loop with a Un-EDF. The flat range covering almost the entire C-band has broad application prospects in high-sensitivity distributed optical fiber sensing and wavelength-division multiplexing.

Switchable multi-wavelength fiber laser based on a taper-coupled microbottle resonator

A multi-wavelength erbium-doped fiber laser (EDFL) based on a taper-coupled microbottle resonator is proposed and investigated experimentally. The taper-coupled microbottle resonator has the comb filter characteristics with Q factor 2.9 × 104, which is integrated into an EDFL system. The taper-coupled microbottle resonator was packaged by ultraviolet glue, which has excellent stability of output power and wavelength at room temperature. Then, switchable dual-, triple-, quad- and quint-wavelength fiber laser states can be achieved by adjusting the polarization controller (PC). Furthermore, for dual-wavelength and triple-wavelength laser state, the position of output wavelengths also can be precisely modulated with the PC. The developed multi-wavelength EDFL has the optical signal to noise ratio as high as 40 dBm, and the wavelength shift and peak power fluctuation are less than 0.03 nm and 6 dBm.

Tunable and Switchable Multi-Wavelength Erbium-Doped Fiber Laser Based on Composite Structure Filter

A multi-wavelength erbium-doped fiber laser (MW-EDFL) with wide tuning range, switching and adjustable wavelength interval is designed and tested, which is based on a composite filter. The filter consists of a tapered microfiber coupler loop (TMCL) with a nested single mode fiber (SMF)-two mode fiber (TMF)-SMF (STS) structure, which has a comb spectrum with obvious envelope and uniform fluctuation. Our experimental and theoretical results show that the laser can output thirteen wavelengths, when the angles of two polarization controllers (PCs) in the TMCL are accurately set. Moreover, by adjusting the PCs, the tuning range of single- to sextuple-wavelength can reach about 40 nm. Six non-adjacent multi-wavelength outputs can be observed in some specific polarization states. The maximum side-mode suppression ratio (SMSR) of the output laser is 40.6 dB. Compared with other multi-wavelength EDFL, the output characteristics of the laser, such as the adjustability and flexibility of wavelength spacing and the switch-ability of wavelength number, have been improved.

A kind of multiwavelength erbium-doped fiber laser based on Lyot filter

A multiwavelength tunable ring-cavity erbium-doped fiber laser (EDFL) based on a Lyot filter was presented. For the proposed Lyot filter, a comb filter consisting of an EDF-polarization-maintaining fiber (EDF-PMF), a polarization controller (PC), and a circulator with four ports was used to suppress the mode competition. The light transmission direction was guaranteed by the circulator. For the proposed fiber laser, tunable single, dual, triple, quadruple, quintuple, sextuple, and septuple wavelengths were realized. A single-wavelength laser output with an optical signal-to-noise ratio (SNR) of up to 30.56 dB was realized, and a tuning range of 1590.54 nm to 1599.54 nm was achieved by tuning the PC. The stability of the single, dual, triple, and quadruple-wavelength center power fluctuations was less than 0.05 dB, 0.98 dB, 5.07 dB, and 7.71 dB respectively. When the laser was operated in the multiwavelength condition, the SNR was more than 20.97 dB. The proposed erbium-doped fiber laser is suitable for fiber-sensing system applications.

Stable and tunable multi-wavelength erbium-doped fiber lasers using saturable absorbent tungsten disulfide

A multi-wavelength erbium-doped fiber laser using tungsten disulfide (WS2) as a nonlinear saturable absorber is proposed. The laser structure consists of a Lyot filter and a WS2 film in a ring cavity. The WS2 film attached to the end of the fiber jumper can suppress the mode competition phenomenon caused by erbium-doped fiber due to its good nonlinear optical properties. In addition, it can suppress mode contention and stabilize multi-wavelength output. The number of wavelengths can be tuned by adjusting the length of the polarization-maintaining fiber (PMF). In the Lyot filter, the PMF of 4, 8 and 12 m excite 5, 9 and 13 wavelengths with 1.38, 0.7 and 0.42 nm intervals, respectively. The experimental results show that in the range of 1528–1536 nm, the side-mode suppression ratio is 42 dB. After 60 min of continuous excitation, the output wavelength of the structure remains stabilization. It can be used as a light source in distributed sensing and wavelength division multiplexing systems.

Conserved spacing multi-wavelength mode-locked erbium-doped fiber laser based on barium titanate saturable absorber

A compact multi-wavelength harmonic passive mode-locked (MWHML) erbium-doped fiber laser (EDFL) has been demonstrated by integrating a Barium Titanate (BaTiO3) in the ring cavity configuration. The BaTiO3 with 9.5% modulation depth serves as a saturable absorber (SA) and is optically deposited by the Top-Down method to form an end face fiber integrated saturable absorber. Both the saturable absorption property and the large third-order nonlinearity of BaTiO3 assisted in generating a second-order harmonic pulse beside the fundamental frequency. Moreover, in real-time, eight wavelengths around 1560 nm with 0.7 nm wavelength spacing were produced with a maximum output power of 2.7 mW pulse duration of 5.2 ps. These results further suggest that BaTiO3 could be a good candidate for the saturable absorber and high nonlinear photonic device for related applications.

Tunable multiwavelength Erbium-doped fiber laser based on in-fiber Fabry-Perot interferometer fiber Bragg gratings in linear and ring cavity configurations

Multiwavelength Erbium-doped fiber laser (MWEDFL) in the ring and linear cavities operating at 1.5-μm wavelength region was demonstrated. The multiwavelength fiber laser comprises a 3-m Erbium-doped fiber as an active gain medium, an in-fiber Fabry-Perot interferometer Fiber Bragg Gratings (FPI FBG) as a filter, and a 10-km dispersion compensating fiber (DCF) as a nonlinear gain medium. A comparison investigation was conducted. The MWEDFL in the linear cavity generates 12 stable lasing lines, with an optical signal-to-noise ratio (OSNR) of 45 dB. In the case of MWEDFL operated in a ring cavity, 8 stable lasing lines were generated, with an OSNR of 47 dB. The free spectral range (FSR) of 0.08 nm was measured for the FPI FBG in both linear and ring cavities MWEDFL spectrum. Besides, the stability measurement was conducted for 150 min for both MWEDFL cavities. Both lasers had a peak power fluctuation of less than 1.0 dB and negligible wavelength drifts below 0.1 nm. Furthermore, the wavelength tunability of MWEDFL in both configurations was performed by heating the FPI FBG from 28 °C to 100 °C. At the temperature of 100 °C, the MWEDFL shows a wavelength shift of 1.0 nm, and this can be further increased by heating the FPI FBG to its highest temperature limit. This MWEDFL employs in-fiber FPI FBG offers a compact, highly tunable, and simple design applicable for optical communications and optical sensing applications.

Tunable and interval-adjustable multiwavelength Erbium-doped fiber laser based on a compound filter

We propose and experimentally demonstrate a multiwavelength erbium-doped fiber laser (EDFL) based on a compound filter. The compound filter is composed of polarization controllers (PCs), polarizers and a piece of home-made polarization-maintaining photonic crystal fiber (PM-PCF). Due to the high birefringence and few-mode properties of the PM-PCF, Lyot filter and multimode interference filter can be realized simultaneously in the compact structure. Hence, the EDFL can achieve flexible lasing output. By adjusting PCs, the lasing can obtain single-, dual-, triple- and quad-wavelength output, respectively. The tuning range of single-wavelength lasing output can exceed 20 nm with side-mode suppression ratio (SMSR) above 40 dB. For dual-wavelength lasing output, the tuning range with fixed interval can reach 16 nm. Besides, the wavelength interval can be adjusted from 2.5 nm to 17.4 nm. The great interval adjustability is also observed in triple-wavelength output. The wavelength interval can be adjusted from 8.2 nm to 14.7 nm. Compact structure, flexible lasing output, and good stability make our proposed EDFL more convenient and practical to the applications such as sensing and wavelength division multiplexing.

Widely tunable and switchable multiwavelength erbium-doped fiber laser based on a single ring cavity

In this paper, we propose and demonstrate through numerical simulations a novel, to the best of our knowledge, widely tunable and switchable multiwavelength erbium-doped fiber laser (EDFL) operating in the 1524–1650 nm wavelength range covering the C-, L-, and U-bands. The EDFL is based on a single ring cavity and a single forward pump source operating at 980 nm wavelength. The length of the erbium-doped fiber and pumping configuration is optimized, enabling a wide tuning of 126 nm with an average lasing power of 15 dBm. Switchable multiple wavelengths are generated from the EDFL through an intracavity tunable optical filter (TOF) and a specially designed out-of-cavity comb filter (CF). Forty-nine wavelengths having average optical power and linewidth of around −10 dBm and 0.01 nm, respectively, are obtained at the output of the CF. Moreover, the free spectral range among the multiple wavelengths is adjusted easily by simply varying the frequency of sinusoidal radio frequency signal used to modulate the lasing signal obtained by tuning the intracavity TOF at a particular wavelength with the help of a dual-drive Mach–Zehnder modulator. The proposed EDFL is low cost, efficient, and highly stable with an average output power of around 15 dBm for 10% output coupling ratio over a 126 nm wide tuning range covering C-, L- and U-bands.

High SMSR and widely tunable multi-wavelength erbium doped fiber laser based on cascaded filters

In this paper, a widely tunable multi-wavelength erbium doped fiber laser (EDFL) with high side mode suppression ratio (SMSR) is proposed and experimentally demonstrated. With the cascaded structure of Sagnac loop filter (SLF) and a homemade twin core photonic crystal fiber (TCPCF), the proposed EDFL could achieve a wide tunable range without sacrificing the SMSR. By properly adjusting the polarization controller (PC) and the bending stage, switchable single-, dual-, and triple-wavelength lasing outputs can be obtained. The tuning range can reach up to 23 nm and the highest SMSR is 57 dB for single-wavelength lasing. Moreover, dual-wavelength lasing outputs with the tuning range of 19 nm and SMSR higher than 40 dB can also be obtained. The proposed widely tunable EDFL with high SMSR has great significance for many applications such as optical fiber communication, distributed fiber optic sensing and microwave generation.

Flat Multi-Wavelength Brillouin Erbium-Doped Fiber Laser Based on a Sagnac Loop with an Unpumped Erbium-Doped Fiber

Flat Multi-Wavelength Brillouin Erbium-Doped Fiber Laser Based on a Sagnac Loop with an Unpumped Erbium-Doped Fiber