MoS2 Quantum Dots Research Articles

Photoluminescent MoS2 quantum dots surrounded by nucleotides: an experimental and theoretical study

Photoluminescent MoS2 quantum dots surrounded by nucleotides: an experimental and theoretical study

Formamidinium lead iodide perovskite photovoltaics with MoS2 quantum dots

We present the formation of a composite film made out of formamidinium lead iodide (FAPI) and molybdenum disulphide quantum dots (MoS2 QDs) and propose a corresponding photovoltaic device architecture based on a ‘type-I’ alignment of the two materials’ electronic energy levels. The introduction of the MoS2 QDs has not compromised the overall crystallinity of the FAPI film and the composite absorber has shown improved stability. We report on the benefits of this composite film and energy band arrangement as the photogenerated carriers in MoS2 QDs, both positive and negative, are injected into the FAPI host matrix, resulting in an increased current density of 24.19 mA cm−2 compared to a current density of 19.83 mA cm−2 for the control device with FAPI only. The corresponding photoconversion efficiency increases from 12.6 to 15.0%. We also show that inclusion of MoS2 QDs in FAPI films resulted in a notable improvement in the fill factor and open-circuit voltage of the solar cells. Most importantly, MoS2 QDs enhanced the film stability by reducing defect formation and acting as passivating agents that minimize recombination losses and improve charge carrier transport. Our results suggest that a composite film in a type-I device architecture can introduce benefits for both future developments in perovskite solar cells and effectively tackling the longstanding challenges of carrier transport in QDs solar cells.

L-cysteine capped MoS2 QDs for dual-channel imaging and superior Fe3+ ion sensing in biological systems.

MoS2 quantum dots (MQDs) with an average size of 1.9 ± 0.7 nm were synthesized using a microwave-assisted method. Absorbance studies confirmed characteristic transitions of MoS2, with absorption humps at 260-280 nm and 300-330 nm, and a band gap of 3.6 ± 0.1 eV. Fluorescence emission studies showed dominant blue and some green emissions under 315 nm excitation, with an absolute quantum yield of ∼9%. The MQDs exhibited fluorescence stability over time after repeated quenching cycles across various pH and media systems. In vitro toxicity tests indicated cytocompatibility, with around 80% cell survival at 1000 mg L-1. Confocal imaging demonstrated significant uptake and vibrant fluorescence in cancerous and non-cancerous cell lines. The MQDs showed strong selectivity towards Fe3+ ions, with a detection limit of 27.61 ± 0.25 nM. Recovery rates for Fe3+ in phosphate buffer saline (PBS) and simulated body fluid (SBF) systems were >97% and >98%, respectively, with a relative standard deviation (RSD) within 3%, indicating precision. These findings suggest that MQDs have high potential for diagnostic applications involving Fe3+ detection due to their fluorescence stability, robustness, enhanced cell viability, and dual-channel imaging properties.

Building 3D Crosslinked Graphene-MXene Nanoarchitectures Decorated with MoS2 Quantum Dots Enables Efficient Electrocatalytic Hydrogen Evolution.

Although MoS2 quantum dots with abundant edge sites have been regarded as promising eletrode materials for the hydrogen evolution reaction (HER), their electrocatalytic capacity still requires improvements in actual applications. Herein. we demonstrate a controllable and robust bottom-up approach to build 3D crosslinked graphene-Ti3C2Tx MXene frameworks decorated with MoS2 quantum dots (MQD/RGO-MX) via a convenient co-assembly process. The novel structural design gives the MQD/RGO-MX nanoarchitectures a series of superior textural attributes, including 3D interconnected networks, continuous meso- and macropores, well-dispersed quantum dots, ameliorative electronic configuration, and excellent electrical conductivity. Accordingly, the resulting hybrid nanoarchitectures express superior electrocatalytic properties in terms of a low onset potential of only 45 mV, a small Tafel slope of 61 mV dec-1 as well as a long service life towards the HER, which make it quite competitive against bare MoS2 quantum dots, MXene as well as binary MQD/RGO and MQD/MXene electrocatalysts.

Design and understanding of SnO2 architecture decorated by MoS2 quantum dots for enhancing triethylamine sensing

The size effect through quantum dots is an effective method to improve the performance of gas sensors. This paper reports the design of a triethylamine sensor based on a SnO2-MoS2 heterojunction structure. The porous SnO2 was synthesized using a polystyrene microsphere template and then loaded with MoS2 quantum dots (MoS2 QDs) by the impregnation method. The gas-sensitizing properties of the prepared sensors were systematically investigated. Compared with the single SnO2 and MoS2 gas sensing materials, the SnO2-MoS2 sensor showed higher selectivity to triethylamine at the optimal operating temperature of 160 °C, and the response performance was improved by 192%. The results show that the SnO2-MoS2 heterojunction improves the sensing performance due to its unique pore structure, oxygen vacancies and n-n heterojunction. In addition, the energy band structure and triethylamine sensing mechanism of SnO2-MoS2 heterojunctions were analyzed by density functional theory. This work provides significant value for the study of gas-sensitive properties and triethylamine sensors of SnO2 -MoS2 QDs composites.

Nitrogen-doped MoS2 QDs as fluorescent probes for sensitive detection of curcumin and cell imaging

BackgroundCurcumin has been used in traditional medicine because of its pharmacological activity, including antioxidant, antibacterial, anticancer, and anticarcinogenic properties. Therefore, sensitive and selective monitoring of curcumin is highly demand for practical application. ResultsIn this study, we describe the construction of a fluorescence method for curcumin assay based on nitrogen-doped MoS2 quantum dots (N–MoS2 QDs). The N–MoS2 QDs are constructed by a solvothermal method using sodium molybdate and Cys as precursors. With the addition of curcumin, the bright blue fluorescence of N–MoS2 QDs is quenched by the inner filter effect (IFE). The QDs emitted bright blue fluorescence and could be quenched by the addition of curcumin via IFE. The dynamic range is the range of 0.1–10 μM for curcumin detection, with a detection limit of 59 nM. N–MoS2 QDs were applied for curcumin assay in real samples with good recovery. In addition, the N–MoS2 QDs exhibited relative low cytotoxicity and could be applied for fluorescence-based imaging in biological samples. SignificanceOur study indicates that the sensor possesses good selectivity to monitor curcumin in water samples, human urine samples, ginger powder samples, mustard samples, and curry samples with satisfactory recoveries. The N–MoS2 QDs possess less cytotoxicity with excellent biocompatibility and were applied for in vitro cell imaging.

Confinement of excited states in two-dimensional, in-plane, quantum heterostructures

Two-dimensional (2D) semiconductors are promising candidates for optoelectronic application and quantum information processes due to their inherent out-of-plane 2D confinement. In addition, they offer the possibility of achieving low-dimensional in-plane exciton confinement, similar to zero-dimensional quantum dots, with intriguing optical and electronic properties via strain or composition engineering. However, realizing such laterally confined 2D monolayers and systematically controlling size-dependent optical properties remain significant challenges. Here, we report the observation of lateral confinement of excitons in epitaxially grown in-plane MoSe2 quantum dots (~15-60 nm wide) inside a continuous matrix of WSe2 monolayer film via a sequential epitaxial growth process. Various optical spectroscopy techniques reveal the size-dependent exciton confinement in the MoSe2 monolayer quantum dots with exciton blue shift (12-40 meV) at a low temperature as compared to continuous monolayer MoSe2. Finally, single-photon emission (g2(0) ~ 0.4) was also observed from the smallest dots at 1.6 K. Our study opens the door to compositionally engineered, tunable, in-plane quantum light sources in 2D semiconductors.

Investigating the influence of molybdenum disulfide quantum dots coated with DSPE-PEG-TPP on molecular structures of liver lipids and proteins: An in vivo study

Molybdenum disulfide (MoS2) quantum dots (QDs) based therapeutic approaches hold great promise for biomedical applications, necessitating a thorough evaluation of their potential effects on biological systems. In this study, we systematically investigated the impact of MoS2 QDs coated with 1,2-distearoyl-sn-glycero-3-phosphoethanolamine-N-[amino(polyethyleneglycol)-2000](DPSE-PEG) linked with (3-carboxypropyl)triphenyl-phosphonium-bromide (TPP) on molecular structures of hepatic tissue lipids and proteins through a multifaceted analysis. The DSPE-PEG-TPP-MoS2 QDs were prepared and administered to the mice daily for 7 weeks. Liver tissues were subjected to a comprehensive examination using various techniques, including Fourier-transform infrared (FTIR) spectroscopy, UV–vis spectroscopy, and liver function tests. FTIR revealed subtle changes in the lipid composition of liver tissues, indicating potential modifications in the cell membrane structure. Also, the (CH stretching and amides I and II regions) analysis unveiled tiny alterations in lipid chain length and fluidity without changes in the protein structures, suggesting a minor influence of DSPE-PEG-TPP-MoS2 QDs on the liver’s cellular membrane and no effect on the protein structures. Further scrutiny using UV–vis spectroscopy demonstrated that DSPE-PEG-TPP-MoS2 QDs had no discernible impact on the absorbance intensities of aromatic amino acids and the Soret band. This observation implies that the treatment with SPE-PEG-TPP-MoS2 QDs did not induce significant alterations in helical conformation or the microenvironment surrounding prosthetic groups in liver tissues. The liver function tests, including ALP, ALT, AST, and BIL levels, revealed no statistically significant changes in these key biomarkers despite minor fluctuations in their values, indicating a lack of significant liver dysfunction. This study provides a detailed understanding of the effects of DSPE-PEG-TPP-MoS2 QDs on hepatic lipids and proteins, offering valuable insights into the biocompatibility and limited impact on the molecular and functional aspects of the liver tissue. These findings could be essential for the application of MoS2 QDs-based therapies.

Organo‐Soluble Colloidal MoS2 Quantum Dots (QDs) as an Efficient Photocatalyst for α‐Amino Phosphonate Synthesis

Abstractα‐Amino phosphonates are bio‐isosteres of amino acids and have numerous biochemical activities. While they are generally prepared via carbon–phosphorus bond formation using a plethora of methods but using recyclable photo‐catalysts and readily accessible amine and phosphites are not commonly used in synthesis. Herein, we used organo‐soluble MoS2 Quantum Dots (QDs) as an exceptionally efficient nano‐photocatalyst for the synthesis of α‐amino phosphonates. Our approach emphasizes on photocatalysis within organic media, providing a facile and effective method for conducting these intricate organic conversions under mild conditions. This straightforward process harnesses the power of molecular oxygen (O2) as an oxidizing agent. To elaborate, our method is intricately guided by the inherent capability of MoS2 QDs to enter an excited state upon absorption of blue light. This excited state bears appropriate potential energy to initiate the formation of reactive iminium ion species from N‐phenyl benzylamine, thus driving the desired product formation. Mechanistic analysis has also unveiled the pivotal role of MoS2 QDs in generating reactive superoxide radicals from O2 through single electron transfer (SET), underscoring their significance in the process. Remarkably, this photocatalytic transformation furnishes a diverse array of functionalized products, expanding its applicability and potential implications in various contexts.

Elucidating the Role of Electron Transfer in the Photoluminescence of MoS2 Quantum Dots Synthesized by fs-Pulse Ablation.

Herein, MoS2 quantum dots (QDs) with controlled optical, structural, and electronic properties are synthesized using the femtosecond pulsed laser ablation in liquid (fs-PLAL) technique by varying the pulse width, ablation power, and ablation time to harness the potential for next-generation optoelectronics and quantum technology. Furthermore, this work elucidates key aspects of the mechanisms underlying the near-UV and blue emissions the accompanying large Stokes shift, and the consequent change in sample color with laser exposure parameters pertaining to MoS2 QDs. Through spectroscopic analysis, including UV-visible absorption, photoluminescence, and Raman spectroscopy, we successfully unraveled the mechanisms for the change in optoelectronic properties of MoS2 QDs with laser parameters. We realize that the occurrence of a secondary phase, specifically MoO3-x, is responsible for the significant Stokes shift and blue emission observed in this QD system. The primary factor influencing these activities is the electron transfer observed between these two phases, as validated by excitation-dependent photoluminescence and XPS and Raman spectroscopies.

MAA Encapsulated MoS2 Quantum Dots as a Fluorescent Probe for the Sensing of Flavonoid

Transition metal dichalcogenide (TMDs) quantum dots (QDs) have attracted widespread attention among scientific community as fluorescent nanomaterial. Among TMDs, MoS2 has received particular interest due to its novel and intriguing optical properties. In this work hydrothermal method is used to prepare aqueous soluble MoS2 QDs using Molybdenyl acetylacetonate and thiourea as Mo and S precursors, respectively. The solubility of unfunctionalized MoS2 is poor in water and organic solvent, therefore thioglycolic acid is used as surfactant for surface functionalization and to enhance the aqueous solubility & stability. These functionalized QDs have been synthesized at pH 11 using hydrothermal method and explored their structural and optical properties. The as synthesized QDs are characterized using TEM, XRD, FTIR, UV-Vis and PL spectroscopy. The morphological shape of as prepared QDs is spherical with size 4-6.5 nm. The MAA encapsulated MoS2 QDs are further explored as fluorescent probe for the sensitive sensing of flavonoid Quercetin.

Mixed-Dimensional van der Waals Heterostructure (2D ReS2/0D MoS2 Quantum Dots)-Based Broad Spectral Range with Ultrahigh-Responsive Photodetector.

The remarkable properties of two-dimensional (2D) materials have led to significant advancements in photodetection and optoelectronics research. Currently, there are many successful methods that are employed to improve the responsivity of photodetectors, but the limited spectral range of the device remains a limitation. This work demonstrates the development of a mixed-dimensional (2D/0D) hybrid photodetector device fabricated using chemical vapor deposition (CVD)-grown monolayer ReS2 and solution-processed MoS2 quantum dots (QDs). The mixed dimensionality of 2D (ReS2) and zero-dimensional (0D) MoS2 QDs assist in improving the spectral range of the device [ultraviolet (360 nm) to near-infrared (780 nm)]. Further, due to the work function difference between ReS2 and MoS2 QDs, the built-in electric field across the mixed-dimensional interface promotes effective charge separation and migration, resulting in improved responsivities of the device. The calculated responsivities of the fabricated photodetector are 5.4 × 102, 3.3 × 102, and 2.6 × 102 A/W when subjected to visible, UV, and NIR light illumination, which is remarkable when compared to the existing reports on broadband photodetection. The mixed-dimensionality heterostructure coupled with contact engineering paves the way for highly responsive broadband photodetectors for potential applications in security, healthcare, etc.

A novel photoelectrochemical self-screening aptamer biosensor based on CAU-17-derived Bi2WO6/Bi2S3 for rapid detection of quorum sensing signal molecules

Quorum sensing signal molecule is an important biomarker released by some microorganisms, which can regulate the adhesion and aggregation of marine microorganisms on the surface of engineering facilities. Thus, it is significant to exploit a convenient method that can effectively monitor the formation and development of marine biofouling. In this work, an advanced photoelectrochemical (PEC) aptamer biosensing platform was established and firstly applied for the rapid and ultrasensitive determination of N-(3-Oxodecanoyl)-l-homoserine lactone (3-O-C10-HL) released from marine fouling microorganism Ponticoccus sp. PD-2. The visible-light-driven Bi2WO6/Bi2S3 heterojunction derived from metal-organic frameworks (MOFs) CAU-17 and self-screened aptamer were employed as the photoactive materials and bioidentification elements, respectively. Appropriate amount of MoS2 quantum dots (QDs) conjugated with single-stranded DNA were introduced by hybridization to enhance the photocurrent response of the PEC biosensor. The self-screening aptamer can specifically recognize 3-O-C10-HL, accompanied by increasing the steric hindrance and forcing MoS2 QDs to leave the electrode surface, resulting in an obvious reduction of photocurrent and achieving a dual-inhibition signal amplification effect. Under the optimized conditions, the photocurrent response of PEC aptasensor was linear with 3-O-C10-HL concentration from 1 nM to 10 μM, and the detection limit was as low as 0.26 nM. The detection strategy also showed a high reproducibility, superior specificity and good stability. This work not only provides a simple, rapid and ultrasensitive PEC aptamer biosensing strategy for monitoring quorum sensing signal molecules in marine biofouling, but also broadens the application of MOFs-based heterojunctions in PEC sensors.

Photostability and visible-light-driven photoactivity enhancement of hierarchical C@ZnCdS/ZnS/MoS2

Zinc cadmium sulfide solid (Zn x Cd1−x S) related composites received great attention in photocatalytic hydrogen production because of their tunable bandgap and strong visible light absorption range. But sulfide-based metal materials commonly suffer from photo-corrosion issues. It is very important to construct the photocatalysts with high efficient activity and photostability for H2 production. Herein, we successively prepared ZnCdS/ZnS (ZCS/ZS) heterostructures, ZnCdS/ZnS/MoS2 (ZCS/ZS/M) heterostructures decorated ZCS/ZS with MoS2 quantum dots, then we obtained x-C@ZCS/ZS and x-C@ZCS/ZS/M heterostructures encapsulated ZCS/ZS and ZCS/ZS/M with carbon layer. The performance of the photocatalytic hydrogen production showed that sample 0.05-C@ZCS/ZS/M has a remarkable photocatalytic H2 evolution rate of 15.231 mmol·h−1·g−1 with noble metal-free co-catalysts. This rate was approximately 21 times higher than that of the pristine ZCS/ZS photocatalyst. The optimized sample reveals an excellent stability, without activity losses after 10 h. The improved photocatalytic activity can be attributed to the unique heterojunction structure formed by ZCS/ZS and MoS2. Additionally, the carbon films played a crucial role in providing excellent stability by spatially separating the sites for redox reactions, thereby inhibiting the recombination of photo-generated electron–hole pairs.

Progress in Electronic, Energy, Biomedical and Environmental Applications of Boron Nitride and MoS2 Nanostructures.

In this review, we examine recent progress using boron nitride (BN) and molybdenum disulfide (MoS2) nanostructures for electronic, energy, biomedical, and environmental applications. The scope of coverage includes zero-, one-, and two-dimensional nanostructures such as BN nanosheets, BN nanotubes, BN quantum dots, MoS2 nanosheets, and MoS2 quantum dots. These materials have sizable bandgaps, differentiating them from other metallic nanostructures or small-bandgap materials. We observed two interesting trends: (1) an increase in applications that use heterogeneous materials by combining BN and MoS2 nanostructures with other nanomaterials, and (2) strong research interest in environmental applications. Last, we encourage researchers to study how to remove nanomaterials from air, soil, and water contaminated with nanomaterials. As nanotechnology proceeds into various applications, environmental contamination is inevitable and must be addressed. Otherwise, nanomaterials will go into our food chain much like microplastics.

A photodetector based on p-GaN/N-MoS2 QDs heterojunction with high responsivity

Molybdenum disulfide (MoS2) is the most thoroughly investigated for photodetection applications with direct bandgap transition in low-dimensional structures, high light–matter interaction, and good carrier mobility. In this work, MoS2 quantum dots was synthesis by liquid exfoliation and characterized using scanning electron microscopy (SEM), Transmission electron microscopy (TEM), Fluorescence emission spectra (FES), UV–vis spectroscopy, and Photoluminescence (PL). The average size is ∼ 3.6 nm with strong absorption in the UV region and a band gap of 4.49 eV. Moreover, a novel structure of N- MoS2 QDs \\ p-GaN heterojunction photodetector was deposited by spray coating. The PL of N- MoS2 QDs \\ p-GaN emission spectra expanded from UV to visible light with high responsivity to the visible light of 7.06 mA W−1 and detectivity of 1.24 × 1010 jones.

Deep-Learning-Assisted Discriminative Detection of Vitamin B12 and Vitamin B9 by Fluorescent MoSe2 Quantum Dots.

A facile and environmentally mindful approach for the synthesis of MoSe2 QDs was developed via the hydrothermal method from bulk MoSe2. In this, the exfoliation of MoSe2 was enhanced with the aid of an intercalation agent (KOH), which could reduce the exfoliation time and increase the exfoliation efficiency to form MoSe2 QDs. We found that MoSe2 QDs display blue emission that is suitable for different applications. This fluorescence property of MoSe2 QDs was harnessed to fabricate a dual-modal sensor for the detection of both vitamin B12 (VB12) and vitamin B9 (VB9), employing fluorescence quenching. We performed a detailed study on the fluorescence quenching mechanism of both analytes. The predominant quenching mechanism for VB12 is via Förster resonance energy transfer. In contrast, the recognition of VB9 primarily relies on the inner filter effect. We applied an emerging and captivating approach to pattern recognition, the deep-learning method, which enables machines to "learn" patterns through training, eliminating the need for explicit programming of recognition methods. This attribute endows deep-learning with immense potential in the realm of sensing data analysis. Here, analyzing the array-based sensing data, the deep-learning technique, "convolution neural networks", has achieved 93% accuracy in determining the contribution of VB12 and VB9.

A polarization-sensitive, high on/off ratio and self-powered photodetector based on Nb2CT x and Nd2CT x @MoS2

MXene two-dimensional materials have been widely used in energy storage, catalysis, sensing and other fields, Nb2C as a typical two-dimensional MXene material, its exploration in the field of optoelectronics is still in its infancy, especially Nb2C-based photodetectors are still to be developed. This paper demonstrates that two-dimensional films based on few-layer Nb2C have a photoelectric response in the wavelength range from visible to near-infrared. We have found that the light response performance can be easily adjusted by controlling the thickness of the spin-coated film, and that Nb2C photodetectors show great advantages in terms of wide bandwidth, polarization response, high switching ratio, etc. By adjusting the material concentration and sample thickness, the photocurrent can reach up to 330 nA, the switching ratio can reach 410, and the responsivity can reach 8.3 × 10−4 A W−1. In the polarization characteristic test, an extinction ratio of 7.6 can be obtained. By adjusting the content of that doped MoS2 quantum dot, the dark current can reach 7.6 × 10−13 A, and the switching ratio can reach 3 × 105, which can be increased by 700 times. The above results show that the few-layer Nb2C nanosheets can be used as optoelectronic detectors in the visible to near-infrared bands, which further broadens the application prospects of two-dimensional MXene.

Nitrodopamine modified MnO2 NS-MoS2QDs hybrid nanocomposite for the extracellular and intracellular detection of glutathione.

We have developed a highly sensitive and reliable fluorescence resonance energy transfer (FRET) probe using nitro-dopamine (ND) and dopamine (DA) coated MnO2 nanosheet (ND@MnO2 NS and DA@MnO2 NS) as an energy acceptor and MoS2 quantum dots (QDs) as an energy donor. By employing surface-modified MnO2 NS, we can effectively reduce the fluorescence intensity of MoS2 QDs through FRET. It can reduce MnO2 NS to Mn2+ and facilitate the fluorescence recovery of the MoS2 QDs. This ND@MnO2 NS@MoS2 QD-based nanoprobe demonstrates excellent sensitivity to GSH, achieving an LOD of 22.7 nM in an aqueous medium while exhibiting minimal cytotoxicity and good biocompatibility. Moreover, our sensing platform shows high selectivity to GSH towards various common biomolecules and electrolytes. Confocal fluorescence imaging revealed that the nanoprobe can image GSH in A549 cells. Interestingly, the ND@MnO2 NS nanoprobe demonstrates no cytotoxicity in living cancer cells, even at concentrations up to 100 μg mL-1. Moreover, the easy fabrication and eco-friendliness of ND@MnO2 NS make it a rapid and simple method for detecting GSH. We envision the developed nanoprobe as an incredible platform for real-time monitoring of GSH levels in both extracellular and intracellular mediums, proving valuable for biomedical research and clinical diagnostics.

Soluble inorganic quantum dots as an electrolyte additive to boost lithium-sulfur battery performance.

Herein, MoS2 quantum dots (QDs) are constructed to serve as electrolyte additives for lithium-sulfur batteries, which can 'solidify' soluble polysulfides by chemisorption and promote sulfur conversion chemistry by electrocatalysis. The Li-S cell with MoS2 QDs shows high retained capacity and high-rate capability, much better than the counterpart without MoS2 QDs.