Morphology Of Films Research Articles

Insulator-donor electron wavefunction coupling in pseudo-bilayer organic solar cells achieving a certificated efficiency of 19.18%

Abstract The incorporation of polymeric insulators has led to notable achievements in the field of organic semiconductors. By altering the blending concentration, polymeric insulators exhibit extensive capabilities in regulating molecular configuration, film crystallinity, and mitigation of defect states. However, current research suggests that the improvement in such physical properties is primarily attributed to the enhancement of thin film morphology, an outcome that seems to be an inevitable consequence of incorporating insulators. Herein, we report a general and completely new effect of polymeric insulators in organic semiconductors: the insulator-donor electron wavefunction coupling effect. Such insulators can couple with donor polymers to reduce the energy barrier level and facilitate the intramolecular electron transport. Besides the morphological effects, we observed that this coupling effect is another mechanism that can significantly enhance the electron mobility (up to 100 times) through the incorporation of polymeric insulators in a series of donor systems. With this effect, we proposed a polymeric insulator blending approach to fabricate state-of-the-art pseudo-bilayer organic solar cells, and the PM6/L8-BO device exhibits a high efficiency of 19.50% (certificated 19.18%) with the improved interfacial electron transport property. This work not only offers a novel perspective on the quantum effect of polymeric insulators in organic semiconductors, but also presents a simple yet effective method for enhancing the performance of organic solar cells.

Halogen‐free solvent processed organic solar sub‐modules (≈55 cm2) with 14.70% efficiency by controlling the morphology of alkyl chain engineered polymer donor

AbstractGoals of high efficiency, morphological analysis, and the ability to produce organic solar cell (OSC) sub‐modules using halogen‐free solvents are demanding. In this study, a robust conjugated polymer with thienothiophene π‐spacer with pendant alkyl side chain (NapBDT‐C12) was synthesized and used to fabricate sub‐modules. Excellent efficiencies were demonstrated by a NapBDT‐C12 integrated ternary blend, which was used to produce stable small‐area‐to‐sub‐module devices using O‐xylene. The efficiency of the NapBDT‐C12 added small‐area ternary devices (PM6:NapBDT‐C12:L8‐BO) was 18.71%. Owing to the controlled homogeneity of the blend with favorable nanoscale film morphology, enhanced carrier mobilities, and exciton dissociation/splitting properties, contributed to the efficiencies of small‐area‐to‐sub‐module OSCs. Moreover, a 55 cm2 sub‐module with an efficiency of 14.69% was accomplished by bar coating using O‐xylene under ambient conditions. This study displays the potential of a ternary blend based OSC device to produce high efficiency scalable sub‐modules at ambient conditions.image

Sustainable Solution Processing Toward High‐Efficiency Organic Solar Cells: A Comprehensive Review of Materials, Strategies, and Applications

AbstractOrganic solar cells (OSCs) have emerged as promising candidates for renewable energy harvesting due to their lightweight, flexible, and low‐cost fabrication potential. The efficiency of OSCs is largely determined by the choice of solvents, which significantly affect the film morphology of the active layers, the intermixed donor‐acceptor domains, and overall device performance. Beginning with an introduction to the importance of solvent selection, the screening and classification of solvents, emphasizing their characteristics and classification based on sustainability, solubility, and other additional considerations are explored. Various non‐halogenated solvents, highlighting commonly used aromatic solvents, biomass‐derived solvents, and water/alcohol‐based solvents are explored. The state‐of‐the‐art donor and acceptor materials, focusing on efficient donor materials such as PM6 and D18, and high‐performing Y‐series acceptors are also presented. Strategies for developing high‐performance OSCs processed using non‐halogenated solvents are examined, including solvent engineering with additive and additive‐free approaches, ternary strategies, and layer‐by‐layer techniques. The fabrication of large‐area devices using non‐halogenated solvents is addressed, focusing on blade‐coating, slot‐coating, and other processing techniques. Finally, this review outlines future research directions in the non‐halogenated solvent processing of OSCs, emphasizing the need for continuous innovation to overcome existing limitations and propel OSC technology toward commercial viability.

Mechanistic study of β-Ga2O3 nitridation by RF nitrogen plasma for GaN heteroepitaxy

The transformation of 2¯01β-Ga2O3 to h-GaN under exposure to RF nitrogen plasma was monitored in situ by reflection high-energy electron diffraction. Analysis of the reaction kinetics reveals that the nitridation process is initiated by the formation of an oxynitride phase and proceeds via two-dimensional nucleation and growth of wurtzite GaN grains. X-ray photoelectron spectra suggest a Ga−(NxO1−x) type configuration dominates the surface early in the nitridation process. The surface restructuring is followed by a diffusion-fed phase transformation, which propagates the wurzite GaN structure into the substrate upon reaching 70% nitrogen anion site occupation, corresponding to the oxygen solubility in h-GaN. A direct correlation is observed between the nitridated film morphology and the epitaxial film crystallinity, demonstrating control of the residual strain, lateral coherence, and mosaicity in subsequent GaN epitaxy by the nitridation conditions. This study provides mechanistic details of the nitridation reaction of 2¯01β-Ga2O3 facilitating the optimization of the nitridation process toward improving GaN-2¯01β-Ga2O3 heterojunctions.

Impact of molecular architecture and draw ratio on enhancement of targeted mechanical properties of machine direction oriented polyethylene films produced after blown film extrusion

Conventional multi-material multi-layer flexible packaging offers excellent properties. However, it has recycling challenges, necessitating a shift to mono-material multi-layer flexible packaging for example all-polyethylene (PE) packaging which can be tailored through various synthesis and processing methods for different layers. In this work, we study how the key molecular properties (number-average molecular weight ( Mn), weight-average molecular weight ( M w), molecular weight distribution (MWD), comonomer content (short chain branching)) and machine direction orientation (MDO) process draw ratio (MDX) influence the final morphology and mechanical properties of MDO-PE films which are intended as the outer layer of mono-material all-polyethylene multi-layer flexible packaging. Five PE grades and various blends were extruded and blown into films. Selected blown films were machine direction oriented to obtain the final MDO-PE films. Furthermore, one selected PE blown film was processed at different MDO process draw ratios while keeping other process parameters constant. From the molecular properties point of view, the higher molecular weight fractions provide a higher possibility for uniform stretching whereas lower molecular weight fractions provide a higher natural draw ratio and therefore higher modulus and stiffness enhancement. Further, the results show that increasing MDO process draw ratio leads to more fibrillation and increased crystallinity. Consequently, the tensile modulus and stiffness at the higher draw ratios increase as well and are comparable to conventionally used polymers in outer layers of multilayer flexible packaging. Thus, this work demonstrates that MDO-PE films with enhanced modulus can provide sufficient stiffness for the design of outer layer of mono-material multi-layer all-PE packaging which presents higher potential for mechanical recyclability.

Ligands of Nanoparticles and Their Influence on the Morphologies of Nanoparticle-Based Films.

Nanoparticle-based thin films are increasingly being used in various applications. One of the key factors that determines the properties and performances of these films is the type of ligands attached to the nanoparticle surfaces. While long-chain surfactants, such as oleic acid, are commonly employed to stabilize nanoparticles and ensure high monodispersity, these ligands often hinder charge transport due to their insulating nature. Although thermal annealing can remove the long-chain ligands, the removal process often introduces defects such as cracks and voids. In contrast, the use of short-chain organic or inorganic ligands can minimize interparticle distance, improving film conductivity, though challenges such as incomplete ligand exchange and residual barriers remain. Polymeric ligands, especially block copolymers, can also be employed to create films with tailored porosity. This review discusses the effects of various ligand types on the morphology and performance of nanoparticle-based films, highlighting the trade-offs between conductivity, structural integrity, and functionality.

A Review on Film Forming Spray Technology in Wound Management

Purpose: Skin is an important delivery channel for medications, providing both local and systemic effects. One kind of novel medication delivery technology that is administered topically to the skin is called a topical film forming system. The thorough analysis examines how film-forming sprays have revolutionized a variety of fields, including wound care and medicine. The goal is to present a thorough summary of the assessment criteria, composition, and most recent advancements in film-forming sprays intended for wound healing. Methods: The evaluation parameters including film formation, morphology, flexibility, drying time, pH, viscosity, skin irritation, water washability, bioadhesive strength, and container-related evaluations are provided in a systematic manner for film-forming sprays. The review presents findings from a range of research publications that demonstrate various approaches and strategies used to evaluate the properties and effectiveness of film-forming spray formulations. Results: Examples from current research are given to show the variety of uses for film-forming sprays in wound healing. Formulations containing human epidermal growth factor (hEGF) and water- soluble chitosan, propolis from stingless bees, and a complexed polymer film-forming spray for diabetic wound dressing are among the research offerings. In terms of stability, wound closure acceleration, and regulated distribution of therapeutic substances, these formulations show encouraging results. Conclusion: The review concludes that film-forming sprays represent a promising avenue in advanced wound care, offering advantages such as enhanced flexibility, prolonged adherence, and controlled drug delivery.

Surface treatment processed electron transport layers for efficient Sb2S3 solar cells

Solution-processed Sb2S3 thin films and solar cell devices have recently gained popularity due to their easy procedure and outstanding final device performance. Nevertheless, although the substrate has a significant influence on thefollowing functional films, the effect of the substrate in the Sb-based solar cells appears to have not been adequately examined. In this study, we performed an interesting thioacetamide (TA)-assisted surface treatment strategy on the electron transport layer (ETL) to achieve high-quality development of Sb2S3 thin films and based solar devices. The surface treatment of ETLs resulted in a uniform surface, Zn(OH)2 impurity reduction, and excellent wettability. The above enhanced the growth of Sb2S3 thin films with features like extremely large crystal sizes (∼8 um), more homogeneous and dense film morphology, preferred crystal orientation, reduced oxygen content, and fewer defects, which benefits carrier transport. Finally, a device structure constructed of FTO/TiO2/Zn(O,S)/Sb2S3/Spiro/Au was created, resulting in an almost 30 % increase in efficiency, from 4.05 % to 5.21 %. The proposed approach not only gives new insights into generating higher-quality Sb2S3 thin films and devices, but it also presents new concepts and methods for future high-quality sulfide thin film preparation.

Application Of Vanadyl Alkoxoacetylacetonate In Formation Of v2O5 Electrochromic Films

Crystal structure, morphology and electrochromic properties of V2O5 film, prepared using vanadyl alkoxoacetylacetonate as precursor, were studied. We have shown that the obtained vanadium pentoxide contains significant amount of V4+ cations, which is indicated by low electron work function among other things. This results in material possessing anodic electrochromism – coloring upon oxidation – with rapid bleaching process (1 s upon necessary potential application). Anodic coloration is observed in the whole visible light spectrum, as well as in near IR region up to 1100 nm. Obtained data show high prospects for approach to formation of V2O5-based films using vanadyl acetylacetonate as precursor and application of such films as components of smart windows and displays, optical properties of which could be controlled by electrical current application.

On the corrosion resistance of the CoCrFeMnNi high entropy alloys in chloride-containing sulfuric acid solutions

The electrochemical reactivity of the high entropy Cantor alloy (CoCrFeMnNi) was investigated via potentiodynamic polarization curves, electrochemical impedance spectroscopy (EIS), and surface analysis as a function of chloride content, in sulfuric acid solutions. The results revealed that corrosion mechanism of the CoCrFeMnNi alloy at the corrosion potential, is a two-step mechanism, involving one adsorbed intermediate, similar to that of pure iron in the H2SO4, and this model provided a good description of the impedance data. X-ray photoelectron spectroscopy (XPS) surface characterization and impedance data fitting revealed that chloride ions do not alter the corrosion mechanism or the thickness of the surface oxide film. Instead, they affect the corrosion resistance by changing the composition of the oxide film. Additionally, this work demonstrated that the corrosion mechanism of the CoCrFeMnNi alloy varies with the applied potential, as evidenced by impedance measurements under potentiostatic polarization. Surface observations using scanning electron microscopy (SEM) and XPS analysis provided insights into the morphology and composition of the surface oxide film at different applied potentials, explaining the observed changes in impedance.

Facile assembly of SnO2 thin film-based Al/SnO2/Al device for sensing of 260 nm UVC and 365 nm UVA radiation

An Al/SnO2/Al metal-semiconductor-metal (MSM) device was formed by depositing a ∼55 nm thin film of SnO2 on Si substrate. Structural, surface morphology and optical properties of the SnO2 film were studied. The current-voltage (I-V) characteristics of the device were recorded under the dark condition followed by 260 nm-UVC and 365 nm-UVA illumination conditions. Under the dark condition, the device shows a resistivity of 8.05 Ωcm at V=1.5 V bias voltage. The device produces nearly symmetric rectifying-type I-V characteristics under forward and reverse bias conditions. The electrical properties of the device were explained using back-to-back Schottky diode model. Under the dark condition, the ideality factor of the junction under forward and reverse bias were estimated to be 1.08 and 1.72 respectively. The external quantum efficiency of the device under UVC was found to be ∼518.72 % and specific detectivity reached as high as 1.03×109 Jones at 2.0 V with a response time of ∼1 s. The device showed a high signal-to-noise ratio between 0.5 and 1.5 V bias voltages. The values of the ideality factor being greater than 1 was attributed to the presence of point defects in the SnO2 layer as verified by photoluminescence study. This study reveals that the device could be used as a UVC and UVA sensor at a relatively low bias voltage of ∼1.5 V.

Ionized Phenanthroline Derivatives Suppressing Interface Chemical Interactions with Active Layer for High-efficiency Organic Solar Cells with Exceptional Device Stability.

The contact interface between the charge transport interlayer and the active layer is crucial for the non-fullerene organic solar cells (NF OSCs) to achieve high efficiency and long-term stability. In this study, two novel phenanthroline (Phen) derivatives, tbp-Phen and tbp-PhenBr, are developed as efficient cathode interfacial materials (CIMs). The larger steric hindrance substituents and the ionization of nitrogen atoms on the Phen framework jointly enable the tbp-PhenBr CIM with a stable film morphology and immensely suppress the detrimental interface chemical interactions with the NF active layer. Consequently, tbp-PhenBr-based OSC achieves a higher efficiency (PCE=16.34%) than bathocuproine (BCP)-based control device (PCE=13.70%) using PM6:Y6 as the active layer. More importantly, the tbp-PhenBr-based device maintains 80% of its initial efficiency (T80) for 3264 h in dark conditions and 220 h after being heated at 85°C, significantly outperforming the BCP-based device. The tbp-PhenBr CIM also shows broad applicability across various binary and ternary active layer systems, affording a notable PCE of 19.49%. Additionally, the tbp-PhenBr CIM can be processed via a thermal evaporation technique and the prepared devices exhibit high reproducibility. This work provides innovative insights into the molecular design of the CIMs for stable and efficient NF OSCs.

Rapid Microwave Annealing for Improved Crystallinity and Morphology of Perovskite Materials

Perovskite solar cells are gaining significant attention for their remarkable power conversion efficiency, cost‐effective processing, and material abundance. This study investigates the impact of rapid microwave annealing on the crystallinity and morphology of MAPbI3 films on FTO glass substrates. Multifaceted characterization techniques, including field emission scanning electron microscopy (FESEM), X‐ray diffraction (XRD), UV–Vis spectroscopy, photothermal deflection spectroscopy (PDS), and steady‐state photoluminescence (PL) measurements are used to compare microwave‐annealed samples with traditional hotplate‐annealed samples. Microwave annealing yields significantly larger crystals in shorter processing times, suggesting enhanced crystallinity, as evidenced by SEM analysis and XRD data. UV‐Vis and PDS measurements indicate improved optical properties and reduced sub‐bandgap states, while PL results suggest diminished nonradiative recombination in microwave‐annealed samples. However, a partial film detachment has been observed at higher microwave powers, a phenomenon explained by COMSOL simulations. These findings demonstrate rapid microwave annealing as an energy‐efficient and cost‐effective alternative while highlighting the need for further optimization to address film degradation issues, which remain a significant challenge. This research supports the potential for scalable, high‐quality perovskite material production, facilitating large‐scale production and commercialization of next‐generation solar cells.

The effect of Al2O3 surface passivation layer prepared by ALD method on the performance of CdZnTe thick film detectors

In this work, cadmium zinc telluride (CdZnTe) thick films were grown using close-spaced sublimation (CSS), while Al2O3 films of varying thicknesses were deposited by atomic layer deposition (ALD) as surface passivation layers. The influence of the Al2O3 surface passivation layer on the structure, surface morphology, chemical composition and electrical performance of the CdZnTe thick films was analyzed using XRD, EDS, SEM, AFM, XPS and current–voltage (I-V) characterization systems. The results demonstrate that the surface passivation layer could significantly improves surface defects and reduces the surface leakage current (SLC) of CdZnTe thick films. The CdZnTe thick film radiation detector exhibited an improved energy resolution, decreasing from 18.6 % to 15.1 % with a 40 nm Al2O3, as measured using a 60 KeV 241Am γ-ray source.

Rare Adult acute leukemia with Coexisting myeloblastic (basophilic differentiation) & B-lymphoblastic subpopulations Case Study

Abstract Introduction/Objective Acute basophilic leukemia is a very rare subgroup of acute myeloid leukemia that is defined in the 2022 WHO classification by presence of at least 20% blast cells in peripheral blood or bone marrow with immature and maturing cells of basophil lineage. The simultaneous occurrence of two hematological malignancies in a middle- aged adult patient is quite a rare event as evidenced by the rare cases reported in the literature. To our knowledge, this is the first case to be reported with concomitant acute basophilic and B-lymphoblastic leukemia in adult patients. these findings necessitates the comprehensive systematic approach to attain accurate diagnosis and plan the appropriate treatment protocol. Methods/Case Report Bone marrow aspiration & biopsy procedure was performed under local anesthesia and marrow samples were subjected to: lieshman staining of marrow films and direct examination. Immunophenotypic analysis of marrow aspirate by FACS Canto II flow cytometer. Cytogenetics studies were done as karyotyping and gene mutation detection by FISH. Results (if a Case Study enter NA) NA Conclusion Morphology of marrow films: 50% Blast cells, group of them are medium to larg-cells with high nucleocytoplasmic ratio and immature chromatin and the other group shows blast cells with sparse basophilic granulations, plus 20% immatue and maturing basophils. IPT shows two populations: the Myeloblast population (basophilic differentiation) is Positive for CD45dim, CD34het, CD13, CD33, CD117prt, CD25het, CD123het, cyt MPO part, HLA-DR partial. the B lineage lymphoblast population is Positive for CD45dim, CD34het, CD19, CD79a, TdT, CD20het, CD38. Cytogenetics studies: hyperploidy 56, (X, Y, 9, 10, 12, 13, 15, 18, 22, mar+ extra-chromosomes) FISH: +ve for FLT3-ITD mutation. the picture is by morphology & IPT consistent with biclonal leukemia, myeloid clone (acute basophilic leukemia) & ProB-ALL. The systematic laboratory approach from careful morphological examination of peripheral blood and bone marrow smears to confirmatory immunophenotypic analysis of marrow specimens by flow cytometry, and the comprehensive cytogenetics analysis, has a vital role in diagnosing such rare and aggressive phenomenon and provide a good chance for planning the appropriate treatment protocol with critical timesaving and cost effectiveness.

Towards device stability of perovskite solar cells through low-cost alkyl-terminated SFX-based hole transporting materials and carbon electrodes

Developing cost-effective, high-efficiency, and stable hole transporting materials (HTMs) is crucial for replacing traditional spiro-OMeTAD in perovskite solar cells (PSCs) and achieving sustainable solar energy solutions. This work presents two novel air-stable HTMs based on a spiro[fluorene-9,9′-xanthene] (SFX) core functionalized with N-methylcarbazole (XC2-M) and N-hexylcarbazole (XC2-H) rings. These HTMs were synthesized via a straightforward, three-step process with good overall yields (∼40%) and low production costs. To further reduce device cost, carbon back electrodes were employed. The resulting PSCs, with a structure of FTO/SnO2/Cs0.05FA0.73MA0.22Pb(I0.77Br0.23)3/HTM/C achieved power conversion efficiencies (PCEs) of 13.5% (XC2-M) and 10.2% (XC2-H), comparable to the reference spiro-OMeTAD device (12.2%). The choice of alkyl chain on the HTM significantly impacts film morphology and device stability. The XC2-H device exhibited exceptional long-term stability, retaining approximately 90% of its initial PCE after 720 h of storage in 30–40% humidity air without encapsulation. This surpasses the performance of both the spiro-OMeTAD (55% retention) and XC2-M (68% retention) devices. The superior stability of XC2-H is attributed to its highly hydrophobic nature and the formation of a compact, smooth film due to interdigitation of the hexyl chains. The straightforward synthesis of XC2-H from commercially available materials offers a promising approach for large-scale PSC production.

Adsorption of Ag, Au, Cu, and Ni on MoS2: theory and experiment

Here, we present results of a computational and experimental study of adsorption of various metals on MoS2. In particular, we analyzed the binding mechanism of four metallic elements (Ag, Au, Cu, Ni) on MoS2. Among these elements, Ni exhibits the strongest binding and lowest mobility on the surface of MoS2. On the other hand, Au and Ag bond very weakly to the surface and have very high mobilities. Our calculations for Cu show that its bonding and surface mobility are between these two groups. Experimentally, Ni films exhibit a composition characterized by randomly oriented nanoscale clusters. This is consistent with the larger cohesive energy of Ni atoms as compared with their binding energy with MoS2, which is expected to result in 3D clusters. In contrast, Au and Ag tend to form atomically flat plateaued structures on MoS2, which is contrary to their larger cohesive energy as compared to their weak binding with MoS2. Cu displays a surface morphology somewhat similar to Ni, featuring larger nanoscale clusters. However, unlike Ni, in many cases Cu exhibits small plateaued surfaces on these clusters. This suggests that Cu likely has two competing mechanisms that cause it to span the behaviors seen in the Ni and Au/Ag film morphologies. These results indicate that calculations of the initial binding conditions could be useful for predicting film morphologies. In addition, out calculations show that the adsorption of adatoms with odd electron number like Ag, Au, and Cu results in 100% spin-polarization and integer magnetic moment of the system. Adsorption of Ni adatoms, with even electron number, does not induce a magnetic transition.

Influence of sulfurization process in tin sulfide and sulfur mixed vapors on the morphology of Cu2SnS3 thin films

Abstract Cu2SnS3 (CTS) is expected to be an absorber material for next-generation solar cells because it is composed of nontoxic, low-cost elements and has an absorption coefficient of >104 cm−1. In this study, the effects of sulfurization in tin sulfide (Sn x S y ) and S mixed vapors on various properties of CTS were investigated by using a 3-zone tube furnace to suppress carrier recombination at the grain boundaries and control the composition of the CTS. The CTS deposited via sulfurization in S vapor only (1-zone CTS) contained different monoclinic and tetragonal CTS structures. The grain size of the CTS thin films deposited via sulfurization in Sn x S y and S mixed vapors was not increased. On the other hand, crystal structure analysis revealed that the CTS had grown to single-phase monoclinic CTS. The results suggest that precipitation in Sn x S y and S mixed vapors contributes to the growth of monoclinic CTS with suitable power-generation characteristics. This finding is important for realizing high-efficiency CTS-based solar cells.

Achieving vertical orientation films with superior environmental stability in quasi-2D lead iodide perovskites

The incorporation of a spacer cation to improve the stability of lead halide perovskites entails a trade-off, notably compromising film quality and device performance, particularly in quais-2D variants employing a higher proportion of hydrophobic, larger spacer cations. Addressing this challenge in quasi-2D perovskite-based devices requires enhancement in film morphology, crystallinity, and vertical orientation to optimize charge transport. Herein, we present a simple one step spin coating synthesis approach for producing PEA2MAn-1PbnI3n+1 (n = 5–2) thin films from a single precursor solution. Notably, our method operates at room temperature without the need of usually toxic anti-solvent or specialized additives, resulting in high quality crystalline films that are vertically oriented and smooth. We systematically investigate the impact of annealing processes on crystal structure, including gradient annealing (GA) as well as thermal annealing at 100℃ for durations of 10 and 15 minutes. Our findings indicate that the films with n = 4 exhibits superior crystallinity and vertical crystallographic orientation, alongside reduced roughness, and minimal contamination of the lower n mixtures. Gradient annealing notably enhances the crystallinity of n = 3 films. While the surface of all the films appears smooth with flake-like structure, the n = 2 sample notably exhibits pitting.

HFE-7100 spray cooling under microgravity: Liquid film dynamics and heat transfer

Spray cooling under microgravity is not only motivated by space applications but also by the essential pursuit of the exploration spirit facing the unknown. This study was the first series of scientific experiments conducted at the China New Microgravity Experiment Facility with Electromagnetic Launch. In this study, the liquid film dynamics and heat transfer characteristics of HFE-7100 spray, including liquid film morphology, wetted area, equivalent diameter, and velocity under different inlet pressures and heat fluxes, were quantitatively captured on smooth and rough silicon surfaces under microgravity. Several classic scenarios of liquid films, including spreading, bifurcating, bridging, fusiform, tadpole-shaped, and isolated liquid film, were recognized for the first time. The morphologies of the liquid films and the heat transfer performance under smooth and rough surfaces showed insignificant differences under normal and microgravity conditions. In addition, the dimensionless groups (Weber number and Reynolds number) were updated corresponding to approximately 92.4 % of the total We samples and approximately 96.4 % of the total Re samples ranging from 0.01 to 1 and 10 to 300, respectively, regardless of the different coolants (HFE-7100 and HFE-7000), pressures, nozzle-to-surface heights, heat fluxes, surface conditions, orientations, and gravities (1 g and µg).