Monomeric Precursors Research Articles

Novel Vapor-Phase Synthesis of Flexible, Homogeneous Organic-Inorganic Hybrid Gate Dielectric with sub 5 nm Equivalent Oxide Thickness.

Organic-inorganic hybrid dielectrics have attracted considerable attention for improving both the dielectric constant ( k) and mechanical flexibility of the gate dielectric layer for emerging flexible and wearable electronics. However, conventional solution-based hybrid materials, such as nanocomposite and self-assembled nanodielectrics, have limitations in the dielectric quality when the thickness is deep-scaled, which is critical to realizing high-performance flexible devices. This study proposes a novel vapor-phase synthesis method to form an ultrathin, homogeneous, high- k organic-inorganic hybrid dielectric. A series of hybrid dielectrics is synthesized via initiated chemical vapor deposition (iCVD) in a one-step manner, where 2-hydroxyethyl methacrylate and trimethylaluminum are used as the monomer and inorganic precursor, respectively. The thickness and composition are effectively controlled to form a uniform, defect-free hybrid dielectric. As a result, the synthesized hybrid dielectric has a high- k value as high as 7 and exhibits a low leakage current density of less than 3 × 10-7 A/cm2 at 2 MV/cm, even with an equivalent oxide thickness of less than 5 nm. Furthermore, the dielectric layer shows exceptional chemical stability without any degradation in its dielectric performance and a smooth surface morphology. The dielectric layer also has good flexibility, maintaining its excellent dielectric performance under a tensile strain of up to 2.6%. Organic thin-film transistors with the developed hybrid dielectric as the gate dielectric achieved hysteresis-free transfer characteristics, with an operating voltage of up to 4 V and excellent mechanical flexibility as well. The hybrid dielectric synthesized via the iCVD process is a promising candidate for high-performance, low-power flexible electronics.

Copper(I)-catalyzed azide–alkyne cycloaddition polymerization of N-butyl-N-ethynyl-4-azidobenzenesulfonamide

Aiming at synthesis of nonperiodic sequence-controlled polymers, we have been focusing on copper(I)-catalyzed azide–alkyne cycloaddition (CuAAC) polymerization of monomers possessing both azide and alkyne groups. For this purpose, we have chosen N-ethynyl-4-azidobenzenesulfonamide derivatives because the derivatives carrying various substituents can be prepared in a fewer steps using the corresponding starting materials, i.e., amines. In this study, we synthesized a new monomer, i.e., N-butyl-N-ethynyl-4-azidobenzenesulfonamide (BuEA), and carried out its dimerization and polymerization by CuAAC using a pair of copper(II) sulfate pentahydrate and sodium ascorbate. A dimer of BuEA was successfully obtained from the monomer precursors possessing azide and ethynyl groups, respectively. This observation indicates that N-ethynyl-4-azidobenzenesulfonamide derivatives are applicable to synthesis nonperiodic sequence-controlled polymers. The polymer obtained (poly(BuEA)) was well soluble in common organic solvents, e.g., dimethyl sulfoxide, N,N-dimethylformamide, tetrahydrofuran (THF), chloroform, and dichloromethane. Solution properties of poly(BuEA) were also investigated. Pulse-field-gradient spin-echo (PGSE) NMR data in THF-d8 indicated that poly(BuEA) chain takes a compact conformation. Steady state fluorescence study exhibited that poly(BuEA) emitted weak fluorescence based on the monomer unit.

Expression, purification and biological activity of monomeric insulin precursors from methylotrophic yeasts

The methylotrophic yeasts Pichia pastoris and Hansenula polymorpha have been used for the production of recombinant monomeric insulin precursor (MIP). Recombinant plasmids with one, two and four cassettes of the MIP gene have been successfully constructed in the pPICZαA expression vector to study the effects of gene copy number on MIP production. The MIP protein can be detected by dot-blot analysis from the culture broth of P. pastoris KM71H 24 h after placement in MMH induction medium. The secretion levels of MIP protein in culture broth at 72 h after induction indicated that P. pastoris KM71H with one cassette of the MIP gene had highest MIP protein levels (4.19 ± 0.96 mg L−1). The transcription levels of the MIP gene increased proportionately with copy number. However, the amount of secreted MIP protein showed no correlation. The MIP molecular mass was 5756.951 Da, as confirmed by typical MALDI-TOF mass spectrometry. The MIP protein in culture broth was purified by two steps purification including SP Sepharose Fast Flow chromatography followed by ultrafiltration (10 kDa MW cutoff). The percentage of MIP recovery after the two-step purification was 70%, with a single band in a native-PAGE. The biological activity of tryptic hydrolyzed MIP was determined via the expression of the glucose transporter 4 gene (GLUT4) in H9c2 (2-1) cell line by RT-qPCR, and the results demonstrated that the MIP protein can induce glucose uptake and upregulation of GLUT4 mRNA transcription at 3 h and that this activity was related to Humalog® insulin.

High performance carbon supercapacitor electrodes derived from a triazine-based covalent organic polymer with regular porosity

A series of highly microporous carbon materials was produced by carbonization of a triazine-based covalent organic polymer (TCOP) followed by carbonization and CO2 physical activation. The N-containing porous COP was prepared from easily available economic monomer precursors via a simple Friedel-Crafts reaction, which produced a predominantly microporous structure with a high surface area. Carbonization at 600–900 °C produced predominantly microporous carbons with a narrow pore size distribution in the range of 0.5–1.5 nm. Upon further activation using CO2, more micropores were formed, accompanied by an increase in the surface area (to 2003 m2 g−1) and the nitrogen level in the carbon structure was maintained at ca. 2 wt%. The electrochemical properties of the samples were measured by employing a three-electrode system with 6 M KOH electrolyte. Among the prepared carbon samples, the electrode fabricated using the carbon activated at 900 °C (AC-900) had a specific capacitance of 278 F g−1 at a current density of 1 A g−1, which is significantly higher than that of a commercial activated carbon (130 F g−1) and ranks among the highest reported so far. This improved performance was attributed to the highly microporous structure of the nitrogen-doped carbon with a narrow pore size distribution.

Tuning the morphology of chevron-type graphene nanoribbons by choice of annealing temperature

Bottom-up synthesis of graphene nanoribbons (GNRs) by surface-assisted polymerization and cyclodehydrogenation of specifically designed precursor monomers has been shown to yield precise edges and doping. Here we use a precursor monomer containing sulfur atoms to fabricate nanostructures on a Au(111) surface at different annealing temperatures. The nanostructures have distinct configurations, varying from sulfur-doped polymers to sulfur-doped chevron-type GNRs (CGNRs) and, finally, pristine graphene nanoribbons with specific edges of periodic five-member carbon rings. Non-contact atomic force microscopy provides clear evidence for the cleavage of C–S bonds and formation of pristine CGNRs at elevated annealing temperatures. First-principles calculations show that the CGNRs exhibit negative differential resistance.

Pirin: A novel redox-sensitive modulator of primary and secondary metabolism in Streptomyces

Pirins are evolutionarily conserved iron-containing proteins that are found in all kingdoms of life, and have been implicated in diverse molecular processes, mostly associated with cellular stress. In the present study, we started from the evidence that the insertional inactivation of pirin-like gene SAM23877_RS18305 (pirA) by ΦC31 Att/Int system-based vectors in spiramycin-producing strain Streptomyces ambofaciens ATCC 23877 resulted in marked effects on central carbon and energy metabolism gene expression, high sensitivity to oxidative injury and repression of polyketide antibiotic production. By using integrated transcriptomic, proteomic and metabolite profiling, together with genetic complementation, we here show that most of these effects could be traced to the inability of the pirA-defective strain to modulate beta-oxidation pathway, leading to an unbalanced supply of precursor monomers for polyketide biosynthesis. Indeed, in silico protein-protein interaction modeling and in vitro experimental validation allowed us to demonstrate that PirA is a novel redox-sensitive negative modulator of very long-chain acyl-CoA dehydrogenase, which catalyzes the first committed step of the beta-oxidation pathway.

The effects of the long flexible chain reactive monomers on blue phase liquid crystals

The effect of flexible chain length of diacrylate monomers on the stabilization of blue phase liquid crystal has been studied in this study. The temperature range of the polymer stabilized blue phase liquid crystal was able to increase by altering the type of the monomer in the monomer precursors due to the difference in the flexibility of polymer backbones. Furthermore, the morphological study proved that the monomer flexibility plays a key role in the formation of the polymer network in a different size and morphology.

Dengue envelope-based \u2018four-in-one\u2019 virus-like particles produced using Pichia pastoris induce enhancement-lacking, domain III-directed tetravalent neutralising antibodies in mice

Dengue is a significant public health problem worldwide, caused by four antigenically distinct mosquito-borne dengue virus (DENV) serotypes. Antibodies to any given DENV serotype which can afford protection against that serotype tend to enhance infection by other DENV serotypes, by a phenomenon termed antibody-dependent enhancement (ADE). Antibodies to the viral pre-membrane (prM) protein have been implicated in ADE. We show that co-expression of the envelope protein of all four DENV serotypes, in the yeast Pichia pastoris, leads to their co-assembly, in the absence of prM, into tetravalent mosaic VLPs (T-mVLPs), which retain the serotype-specific antigenic integrity and immunogenicity of all four types of their monomeric precursors. Following a three-dose immunisation schedule, the T-mVLPs elicited EDIII-directed antibodies in mice which could neutralise all four DENV serotypes. Importantly, anti-T-mVLP antibodies did not augment sub-lethal DENV-2 infection of dengue-sensitive AG129 mice, based on multiple parameters. The ‘four-in-one’ tetravalent T-mVLPs possess multiple desirable features which may potentially contribute to safety (non-viral, prM-lacking and ADE potential-lacking), immunogenicity (induction of virus-neutralising antibodies), and low cost (single tetravalent immunogen produced using P. pastoris, an expression system known for its high productivity using simple inexpensive media). These results strongly warrant further exploration of this vaccine candidate.

The scaffold proteins of lignin biosynthetic cytochrome P450 enzymes.

Lignin is a complex and irregular biopolymer of crosslinked phenylpropanoid units in plant secondary cell walls. Its biosynthesis requires three endoplasmic reticulum (ER)-resident cytochrome P450 monooxygenases, C4H, C3'H and F5H, to establish the structural characteristics of its monomeric precursors. These P450 enzymes were reported to associate with each other or potentially with other soluble monolignol biosynthetic enzymes to form an enzyme complex or a metabolon. However, the molecular basis governing such enzyme or pathway organization remains elusive. Here, we show that Arabidopsis membrane steroid-binding proteins (MSBPs) serve as a scaffold to physically organize monolignol P450 monooxygenases, thereby regulating the lignin biosynthetic process. We find that although C4H, C3'H and F5H are in spatial proximity to each other on the ER membrane in vivo, they do not appear to directly interact with each other. Instead, two MSBP proteins physically interact with all three P450 enzymes and, moreover, MSBPs themselves associate as homomers and heteromers on the ER membrane, thereby organizing P450 clusters. Downregulation of MSBP genes does not affect the transcription levels of monolignol biosynthetic P450 genes but substantially impairs the stability and activity of the MSBP-interacting P450 enzymes and, consequently, lignin deposition, and the accumulation of soluble phenolics in the monolignol branch but not in the flavonoid pathway. Our study suggests that MSBP proteins are essential structural components in the ER membrane that physically organize and stabilize the monolignol biosynthetic P450 enzyme complex, thereby specifically controlling phenylpropanoid-monolignol branch biosynthesis.

A wheat caffeic acid 3-O-methyltransferase TaCOMT-3D positively contributes to both resistance to sharp eyespot disease and stem mechanical strength

Plant caffeic acid 3-O-methyltransferase (COMT) has been implicated in the lignin biosynthetic pathway through catalyzing the multi-step methylation reactions of hydroxylated monomeric lignin precursors. However, genetic evidence for its function in plant disease resistance is poor. Sharp eyespot, caused primarily by the necrotrophic fungus Rhizoctonia cerealis, is a destructive disease in hexaploid wheat (Triticum aestivum L.). In this study, a wheat COMT gene TaCOMT-3D, is identified to be in response to R. cerealis infection through microarray-based comparative transcriptomics. The TaCOMT-3D gene is localized in the long arm of the chromosome 3D. The transcriptional level of TaCOMT-3D is higher in sharp eyespot-resistant wheat lines than in susceptible wheat lines, and is significantly elevated after R. cerealis inoculation. After R. cerealis inoculation and disease scoring, TaCOMT-3D-silenced wheat plants exhibit greater susceptibility to sharp eyespot compared to unsilenced wheat plants, whereas overexpression of TaCOMT-3D enhances resistance of the transgenic wheat lines to sharp eyespot. Moreover, overexpression of TaCOMT-3D enhances the stem mechanical strength, and lignin (particular syringyl monolignol) accumulation in the transgenic wheat lines. These results suggest that TaCOMT-3D positively contributes to both wheat resistance against sharp eyespot and stem mechanical strength possibly through promoting lignin (especially syringyl monolignol) accumulation.

Synthesis of High Molecular Weight Poly(glycerol monomethacrylate) via RAFT Emulsion Polymerization of Isopropylideneglycerol Methacrylate.

High molecular weight water-soluble polymers are widely used as flocculants or thickeners. However, synthesis of such polymers via solution polymerization invariably results in highly viscous fluids, which makes subsequent processing somewhat problematic. Alternatively, such polymers can be prepared as colloidal dispersions; in principle, this is advantageous because the particulate nature of the polymer chains ensures a much lower fluid viscosity. Herein we exemplify the latter approach by reporting the convenient one-pot synthesis of high molecular weight poly(glycerol monomethacrylate) (PGMA) via the reversible addition–fragmentation chain transfer (RAFT) aqueous emulsion polymerization of a water-immiscible protected monomer precursor, isopropylideneglycerol methacrylate (IPGMA) at 70 °C, using a water-soluble poly(glycerol monomethacrylate) (PGMA) chain transfer agent as a steric stabilizer. This formulation produces a low-viscosity aqueous dispersion of PGMA–PIPGMA diblock copolymer nanoparticles at 20% solids. Subsequent acid deprotection of the hydrophobic core-forming PIPGMA block leads to particle dissolution and affords a viscous aqueous solution comprising high molecular weight PGMA homopolymer chains with a relatively narrow molecular weight distribution. Moreover, it is shown that this latex precursor route offers an important advantage compared to the RAFT aqueous solution polymerization of glycerol monomethacrylate since it provides a significantly faster rate of polymerization (and hence higher monomer conversion) under comparable conditions.

Acaulins A and B, Trimeric Macrodiolides from Acaulium sp. H-JQSF.

Acaulin A (1) and its macrolactone ring-opened congener acaulin B (2) were characterized from the culture of Acaulium sp. H-JQSF (an isopod-associated fungus) as architecturally undescribed trimeric macrodiolides, with the former being antiosteoporotic at 0.4 μM in the prednisolone-induced osteoporotic zebrafish. Identification of acaudiolic acid (3) as the monomeric macrodiolide precursor facilitated the proposal of the acaulin biosynthetic pathway.

Biotechnological production of mono- and diamines using bacteria: recent progress, applications, and perspectives.

Common plastics such as polyamides are derived typically from petroleum or natural gas. Fossil-based polyamide production often involves toxic precursors or intermediates. By contrast, bio-based polyamides offer a realistic alternative. Bio-based routes to monomeric precursors of polyamides such as diamines, dicarboxylic acids, and omega-amino acids have been developed. Recent advances in the metabolic engineering of the biotechnologically relevant Escherichia coli and Corynebacterium glutamicum for the production of monoalkylamines such as omega-amino acids as well as diamines are presented.

Poly(diphenylamine-co-aniline) copolymers for supercapacitor electrodes

Polyaniline, polydiphenylamine, and two copolymers with precursor monomers molar ratios of 1:1 and 3:1 (anilinium dodecyl sulfate (P1):diphenylamine) were synthesized via oxidative polymerization in a water/ethanol interfacial system. The morphology characterization and physicochemical properties showed that the copolymers share polyaniline or polydiphenylamine characteristics, depending on the monomer molar ratio. The electroactivity characterization indicated that the polydiphenylamine (PDPA) repeating units provided the copolymers with better cycling stability, whereas PAni repeating units reduced resistance and improved storage capacity, generating a synergistic interaction. Particularly, the copolymer with the highest content of P1, showed a specific capacitance of 341.93 F g−1, with a 74.5% capacitance retention after 500 cycles, which suggests a feasible application in electrodes for supercapacitor design.

Visible light-driven oxygen evolution using a binuclear Ru-bda catalyst

Binuclear ruthenium complexes bearing the 2,2'-bipyridine-6,6'-dicarboxylate (bda) ligand have been demonstrated to be highly active catalysts towards water oxidation with CeIV as an oxidant. However, the catalytic properties of ruthenium dimers have not yet been explored for visible light-driven water oxidation. Herein, the photocatalytic performance of a dipyridyl propane-bridged ruthenium dimer 2 was investigated in comparison with its monomeric precursor, [Ru(bda)(pic)2] (1), in CH3CN/phosphate buffer mixed solvent in a three-component system including a photosensitizer and a sacrificial electron acceptor. Experimental results showed that the activity of each catalyst was strongly dependent on the content of CH3CN in the phosphate buffer, which not only affected the driving force for water oxidation, but also altered the kinetics of the reaction, probably through different mechanisms associated with the O–O bond formation. As a result, dimer 2 showed significantly higher activity than monomer 1 in the solvent containing a low content of CH3CN, and comparable activities were attained with a high content of CH3CN in the solvent. Under the optimal conditions, complex 2 achieved a turnover number of 638 for photocatalytic O2 evolution.

New Spin on Organic Radical Batteries-An Isoindoline Nitroxide-Based High-Voltage Cathode Material.

Organic electrode materials are a highly promising and environmentally benign class of battery materials with radical polymers being at the forefront of this research. Herein, we report the first example of the 1,1,3,3-tetramethylisoindolin-2-yloxyl class of nitroxides as an organic electrode material and the synthesis and application of a novel styrenic nitroxide polymer, poly(5-vinyl-1,1,3,3-tetramethylisoindolin-2-yloxyl) (PVTMIO). The polymer was synthesized from the precursor monomer, 2-methoxy-5-vinyl-1,1,3,3-tetramethylisoindoline, and subsequent oxidative deprotection yielded the electroactive radical species. Cyclic voltammetry revealed a high oxidation potential of 3.7 V versus Li, placing it among the top of the nitroxide class of electrode materials. The suitability of PVTMIO for utilization in a high-voltage organic radical battery was confirmed with a discharge capacity of 104.7 mAh g-1, high rate performance, and stability under cycling conditions (90% capacity retention after 100 cycles), making it one of the highest reported organic p-dopable cathode materials.

Total Synthesis of Aurofusarin: Studies on the Atropisomeric Stability of Bis-Naphthoquinones.

An efficient annulation involving pyrone addition to a quinone and Dieckmann condensation was developed for rapid assembly of a γ-naphthopyrone monomeric precursor to the bis-naphthoquinone natural product aurofusarin. Dimerization was achieved through PdII -catalyzed dehydrogenative coupling. Further studies employing asymmetric nucleophilic epoxidation indicate that the atropisomers of aurofusarin and derivatives are not configurationally stable at ambient temperature.

Total Synthesis of Aurofusarin: Studies on the Atropisomeric Stability of Bis‐Naphthoquinones

AbstractAn efficient annulation involving pyrone addition to a quinone and Dieckmann condensation was developed for rapid assembly of a γ‐naphthopyrone monomeric precursor to the bis‐naphthoquinone natural product aurofusarin. Dimerization was achieved through PdII‐catalyzed dehydrogenative coupling. Further studies employing asymmetric nucleophilic epoxidation indicate that the atropisomers of aurofusarin and derivatives are not configurationally stable at ambient temperature.

Dynamic Changes of Intracellular Monomer Levels Regulate Block Sequence of Polyhydroxyalkanoates in Engineered Escherichia coli.

Biological polymer synthetic systems, which utilize no template molecules, normally synthesize random copolymers. We report an exception, a synthesis of block polyhydroxyalkanoates (PHAs) in an engineered Escherichia coli. Using an engineered PHA synthase, block copolymers poly[(R)-2-hydroxybutyrate(2HB)-b-(R)-3-hydroxybutyrate(3HB)] were produced in E. coli. The covalent linkage between P(2HB) and P(3HB) segments was verified with solvent fractionation and microphase separation. Notably, the block sequence was generated under the simultaneous consumption of two monomer precursors, indicating the existence of a rapid monomer switching mechanism during polymerization. Based on in vivo metabolic intermediate analysis and the relevant in vitro enzymatic activities, we propose a model in which the rapid intracellular 3HB-CoA fluctuation during polymer synthesis is a major factor in generating block sequences. The dynamic change of intracellular monomer levels is a novel regulatory principle of monomer sequences of biopolymers.

Synthesis of Silica-coated Iron Oxide Nanoparticles: Preventing Aggregation without Using Additives or Seed Pretreatment.

The Stober process is frequently used to prepare silica-coated iron oxide nanoparticles. This is usually achieved by seeding a reaction mixture consisting of water, ethanol and a catalyst with iron oxide particles and adding a silica precursor. The hydrolysis and condensation of precursor monomers results in the deposition of a silica layer on iron oxide particles. However, this process is accompanied by an increase in the ionic strength of the medium which promotes the rapid aggregation of iron oxide particles. A number of methods have been developed to prevent seed aggregation during the coating process. The majority of these methods include a pretreatment step in which the surface of iron oxide particles is modified in a manner that increases their stability in aqueous solutions. Here we suggest that by decreasing the initial concentration of the catalyst for a short period to minimize nucleation by reducing precursor hydrolysis rate and then gradually increasing the concentration to the optimum level to allow silica formation to proceed normally it may be possible to prevent aggregation without surface modification. The properties of the resulting nanoparticles as analyzed by transmission electron microscopy and magnetometry as well as their efficiency at extracting genomic DNA from different bacterial strains compared to that of a commercial extraction kit are also reported.