Molecularly Imprinted Polymer Binding Research Articles

Machine learning-assisted Te–CdS@Mn3O4 nano-enzyme induced self-enhanced molecularly imprinted ratiometric electrochemiluminescence sensor with smartphone for portable and visual monitoring of 2,4-D

Here, a novel and portable machine learning-assisted smartphone-based visual molecularly imprinted ratiometric electrochemiluminescence (MIRECL) sensing platform was constructed for highly selective sensitive detection of 2,4-Dichlorophenoxyacetic acid (2,4-D) for the first time. Te doped CdS-coated Mn3O4 (Te–CdS@Mn3O4) with catalase-like activity served as cathode-emitter, while luminol as anode luminophore accompanied H2O2 as co-reactant, and Te–CdS@Mn3O4 decorated molecularly imprinted polymers (MIPs) as recognition unit, respectively. Molecular models were constructed and MIP band and binding energies were calculated to elucidate the luminescence mechanism and select the best functional monomers. The peroxidase activity and the large specific surface area of Mn3O4 and the electrochemical effect can significantly improve the ECL intensity and analytical sensitivity of Te–CdS@Mn3O4. 2,4-D-MIPs were fabricated by in-situ electrochemical polymerization, and the rebinding of 2,4-D inhibits the binding of H2O2 to the anode emitter, and with the increase of the cathode impedance, the ECL response of Te–CdS@Mn3O4 decreases significantly. However, the blocked reaction of luminol on the anode surface also reduces the ECL response. Thus, a double-reduced MIRECL sensing system was designed and exhibited remarkable performance in sensitivity and selectivity due to the specific recognition of MIPs and the inherent ratio correction effect. Wider linear range in the range of 1 nM–100 μM with a detection limit of 0.63 nM for 2,4-D detection. Interestingly, a portable and visual smartphone-based MIRECL analysis system was established based on the capture of luminescence images by smartphones, classification and recognition by convolutional neural networks, and color analysis by self-developed software. Therefore, the developed MIRECL sensor is suitable for integration with portable devices for intelligent, convenient, and fast detection of 2,4-D in real samples.

Fluorescent molecularly imprinted polymer particles for glyphosate detection using phase transfer agents

In this work, molecular imprinting was combined with direct fluorescence detection of the pesticide Glyphosate (GPS). Firstly, the solubility of highly polar GPS in organic solvents was improved by using lipophilic tetrabutylammonium (TBA+) and tetrahexylammonium (THA+) counterions. Secondly, to achieve fluorescence detection, a fluorescent crosslinker containing urea-binding motifs was used as a probe for GPS-TBA and GPS-THA salts in chloroform, generating stable complexes through hydrogen bond formation. The GPS/fluorescent dye complexes were imprinted into 2–3 nm fluorescent molecularly imprinted polymer (MIP) shells on the surface of sub-micron silica particles using chloroform as porogen. Thus, the MIP binding behavior could be easily evaluated by fluorescence titrations in suspension to monitor the spectral changes upon addition of the GPS analytes. While MIPs prepared with GPS-TBA and GPS-THA both displayed satisfactory imprinting following titration with the corresponding analytes in chloroform, GPS-THA MIPs displayed better selectivity against competing molecules. Moreover, the THA+ counterion was found to be a more powerful phase transfer agent than TBA+ in a biphasic assay, enabling the direct fluorescence detection and quantification of GPS in water. A limit of detection of 1.45 µM and a linear range of 5–55 µM were obtained, which match well with WHO guidelines for the acceptable daily intake of GPS in water (5.32 µM).

A biomimetic enzyme-linked immunosorbent assay (BELISA) for the analysis of gonadorelin by using molecularly imprinted polymer-coated microplates

An original biomimetic enzyme-linked immunoassay (BELISA) to target the small peptide hormone gonadorelin is presented. This peptide has been recently listed among the substances banned in sports by the World Antidoping Agency (WADA) since its misuse by male athletes triggers testosterone increase. Hence, in response to this emerging issue in anti-doping controls, we proposed BELISA which involves the growth of a polynorepinephrine (PNE)–based molecularly imprinted polymer (MIP) directly on microwells. PNE, a polydopamine (PDA) analog, has recently displayed impressive performances when it was exploited for MIP preparation, giving even better results than PDA. Gonadorelin quantification was accomplished via a colorimetric indirect competitive bioassay involving the competition between biotinylated gonadorelin linked to the signal reporter and the unlabeled analyte. These compete for the same MIP binding sites resulting in an inverse correlation between gonadorelin concentration and the output color signal (λ = 450 nm). A detection limit of 277 pmol L−1 was achieved with very good reproducibility in standard solutions (avCV% = 4.07%) and in urine samples (avCV% = 5.24%). The selectivity of the assay resulted adequate for biological specimens and non-specific control peptides. In addition, the analytical figures of merit were successfully validated by mass spectrometry, the reference anti-doping benchtop platform for the analyte. BELISA was aimed to open real perspectives for PNE-based MIPs as alternatives to antibodies, especially when the target analyte is a poorly or non-immunogenic small molecule, such as gonadorelin.Graphical abstractBiomimetic enzyme-linked immunosorbent assay (BELISA)

Molecularly Imprinted Electrochemical Sensor-Based Fe2O3@MWCNTs for Ivabradine Drug Determination in Pharmaceutical Formulation, Serum, and Urine Samples.

Ivabradine hydrochloride (IVR) is a medically important drug because of its ability to lower the heart rate. Techniques reported for IVR determination were expensive, laborious, besides being of poor selectivity. In this study, iron oxide @ carbon nanotube (Fe2O3@MWCNTs) nanocomposite and molecularly imprinted polymer (MIP) were synthesized and used in the fabrication of carbon paste electrodes (CPEs) for the potentiometric detection of IVR in biological and pharmaceutical samples. CPEs of the best sensor were formulated from graphite (41 wt%) as a carbon source, MIP (3 wt.%) as an ionophore, Fe2O3@MWCNTs (5 wt%) as a modifier, and nitrophenyl octyl ether (NPOE, 51 wt.%) as a conductive oil so-called plasticizer. The best sensor exhibits a Nernstian slope (response) of 56 mV decade–1 within the IVR concentration range from 1.0 × 10–3 M to 9.8 × 10–8 M with high selectivity against interfering species (ascorbic, maltose, glucose, lactose, dopamine, glycine) over those reported earlier. The use of Fe2O3@MWCNTs together with MIP in the electrode formulation was found to improve the limit of detection (LOD) from 630 to 98 nM along with high reversibility, a short response time of 30 s, and a good lifetime of more than 2 weeks. The sandwich membrane (SMM) method was used to quantify the H-bonding complexing strength of the MIP binding sites for IVR with Log βILn = 11.33. The constructed sensors were successfully applied for the IVR determination in blood serum, urine, and commercial formulations (Savapran®) with high sensitivity.

Stimulus-Responsive Imprinted Polymer-Based Potentiometric Sensor for Reversible Detection of Neutral Phenols.

Nowadays, polymeric membrane potentiometric sensors based on the molecularly imprinted polymers (MIPs) have been successfully developed for detection of various organic and biological species. However, it is difficult for these sensors to perform reversible detection of the targets due to the high affinities of the MIPs toward the targets. In this work, we propose a novel method for fully reversible potentiometric detection of neutral phenols based on the stimulus-responsive MIP as the selective receptor. Since such smart receptor can switch its recognition abilities according to the external environmental stimuli, the MIP binding sites in the polymeric membrane can be regenerated via the stimulus after each measurement. Thus, potentiometric reversible detection of the target can be achieved. As a proof of concept, the pH-responsive MIP is used as the selective receptor, which can be synthesized by using 4-vinylphenylboronic acid as the functional monomer. The boronate-affinity MIP can covalently bind with a cis-diol containing compound to form a five- or six-membered cyclic ester in a weakly alkaline aqueous solution, while the produced ester dissociates when the surrounding pH is changed to acidic. By using catechol as a model, the proposed smart sensor exhibits a significantly improved reversibility compared to the conventional MIP-based sensor. We believed that the stimulus-responsive MIP-based sensing strategy could provide an appealing way to design reversible MIP-based electrochemical and optical sensors.

Application of molecularly imprinted polymer designed for the selective extraction of ketoprofen from wastewater

A molecularly imprinted polymer (MIP) that is selective to ketoprofen was synthesized and applied in the adsorption of the target compound from water. The MIP was synthesized using a bulk polymerization method at high temperatures (60–80°C), where ketoprofen, 2-vinylpyridine, ethylene glycol dimethacrylate, toluene and 1,1´-azobis(cyclohexanecarbonitrile) were used as template, functional monomer, cross-linker, porogen and initiator, respectively. Non-imprinted polymer (NIP) was synthesized similarly to the MIP but in the absence of ketoprofen. From molecular dynamics simulation, the nature of interactions that occurred between the template and the functional monomer were found to be based on hydrogen bonding. This was confirmed experimentally, where a high extraction efficiency of ≥ 90% was obtained at acidic conditions (pH 5) due to the protonation of ketoprofen. A contact time of 45 min was sufficient for the maximum adsorption of ketoprofen from 10 mL spiked water using 8 mg of the adsorbent. MIP showed greater selectivity than NIP by achieving a relative selectivity coefficient of 7.7 towards ketoprofen in the presence of structurally related pharmaceuticals. Furthermore, the order of sorption onto the MIPs from water was ketoprofen > fenoprofen > gemfibrozil. From a modelling perspective, the Langmuir adsorption isotherm and pseudo-second-order kinetic model gave the best fit, with maximum adsorption capacity of 8.24 mg·g−1 and sorption rate constant of 0.25 mg·g−1·min−1 for MIP. This was translated to chemisorption of ketoprofen onto the homogeneous MIP binding sites. This work demonstrated the great potential of MIP in selective recognition of ketoprofen from wastewater relative to closely related compounds.

G-Quadruplex DNA with an Apurinic Site as a Soft Molecularly Imprinted Sensing Platform.

Molecularly imprinted polymers (MIPs) provide versatile sensor platforms to recognize targets by shape complementarity. However, the rigid structure of the classic MIPs compromises the signal transduction with necessary polymer and target modifications. Herein, we tried to use a flexible DNA that has a perfectly structured folding as the soft molecularly imprinted polymer (SMIP) for a straightforward sensor. As a proof of concept, the guanosine SMIP recognition was achieved by removal of a guanosine from a G-quadruplex-forming sequence (G4). The G4 folding structure with such an apurinic site (AP site) provides a well-defined MIP binding accommodation for guanosine according to the shape complementarity. The guanosine binding at the AP site subsequently leads to a conformation change suitable for remote readout using a G4-specific fluorescent ligand. The G4 sequence and AP site position were optimized for this SMIP behavior. Due to the G4 compact structure and the remaining hydrogen bonding pattern, nucleosides other than guanosine and negatively charged nucleotides exhibit no binding with the AP site, suggesting a high selectivity in the SMIP recognition. The proposed rationale was then convinced by the alkaline phosphatase-catalyzed GMP hydrolysis. Our work will inspire more interest in exploring nucleic acids as the SMIP frameworks due to their variant conformations and well-established molecular engineering.

Computational design of molecularly imprinted polymer for direct detection of melamine in milk

ABSTRACTA novel protocol for use of molecularly imprinted polymer (MIP) in analysis of melamine is presented. Design of polymer for melamine has been achieved using a combination of computational techniques and laboratory trials, the former greatly reducing the duration of the latter. The compatibility and concerted effect of monomers and solvents were also investigated and discussed. Two novel open-source tools were presented which are the online polymer calculator from mipdatabase.com and the application of the Gromacs modelling suite to determine the ideal stoichiometric ratio between template and functional monomer. The MIP binding was characterised for several structural analogues at 1–100 μM concentrations. The use of divinylbenzene (DVB) as cross-linking polymer and itaconic acid as functional monomer allowed synthesis of MIP with imprint factor (IF) of 2.25 for melamine. This polymer was used in high-performance liquid chromatography (HPLC) for the rapid detection of melamine in spiked milk samples with an experimental run taking 7–8 min. This approach demonstrated the power of virtual tools in accelerated design of MIPs for practical applications.

Potentiometric detection of chemical vapors using molecularly imprinted polymers as receptors.

Ion-selective electrode (ISE) based potentiometric gas sensors have shown to be promising analytical tools for detection of chemical vapors. However, such sensors are only capable of detecting those vapors which can be converted into ionic species in solution. This paper describes for the first time a polymer membrane ISE based potentiometric sensing system for sensitive and selective determination of neutral vapors in the gas phase. A molecularly imprinted polymer (MIP) is incorporated into the ISE membrane and used as the receptor for selective adsorption of the analyte vapor from the gas phase into the sensing membrane phase. An indicator ion with a structure similar to that of the vapor molecule is employed to indicate the change in the MIP binding sites in the membrane induced by the molecular recognition of the vapor. The toluene vapor is used as a model and benzoic acid is chosen as its indicator. Coupled to an apparatus manifold for preparation of vapor samples, the proposed ISE can be utilized to determine volatile toluene in the gas phase and allows potentiometric detection down to parts per million levels. This work demonstrates the possibility of developing a general sensing principle for detection of neutral vapors using ISEs.

Low-Range Detection of the Phosphate Group by a Molecularly Imprinted Polymer-Modified Carbon Paste Electrode

A series of size-selective polymeric sensors for the phosphate group was designed and synthesized using the molecularly imprinted polymer (MIP) technique based on the noncovalent interaction of the template dipentyl phosphate with the functional monomer methacrylic acid. Very low-range specific electrochemical detection of phosphate molecules was performed by square wave voltammetry with a modified carbon paste electrode (CPE). Calibration curves were obtained within the linear range of 20-300 nmol L <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-1</sup> for all modified CPEs, with the lowest detection limit determined as 8.82 nmol L <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-1</sup> . Potential inorganic interferents, such as carbonate, nitrate and sulfate ions, were investigated and no signal disturbance was observed for relative concentrations 100 times higher than the phosphate concentration. Furthermore, the modified electrodes also showed good selectivity for phosphate molecules containing alkyl chains up to five carbon atoms. The selectivity study confirmed that imprinted sites were successfully synthesized and only structures that are the same size or smaller than those of the template molecule are selected by maximizing intermolecular interactions at the MIP binding site. Moreover, the sensors presented good stability, maintaining the same degree of selectivity for several months. These sensors were also applied in the determination of phosphate in a cola soft drink.

Aging effect of a molecularly imprinted polymer on a quartz tuning fork sensor for detection of volatile organic compounds

The sensing stability and sensitivity of a molecularly imprinted polymer (MIP) selective to the adsorption of hydrocarbons was studied. The MIP was deposited on a quartz crystal tuning fork (QTF) resonator, whose chemical and physical properties were monitored over time, using Scanning Electron Microscopy (SEM), Brunauer–Emmett–Teller adsorption isotherm analysis (BET), and Fourier transform infrared spectroscopy (FTIR). In addition, kinetic binding analysis of the MIP-modified QTF sensor was carried out for the sensors stored and operated under ambient conditions (740mmHg, 20–23°C). Although the polymer was able to maintain its physical and chemical properties at microscopic, BET adsorption, and spectroscopic levels, the intrinsic adsorption properties of hydrocarbons onto MIP binding sites altered over time, which suggest that the 3-D conformational changes of the polymer binding sites occurring at nanoscopic/angstrom level may cause the sensitivity degradation in MIP. The changes were significantly reduced by stabilizing the polymer under low storage temperatures.

A microvolume molecularly imprinted polymer modified fiber-optic evanescent wave sensor for bisphenol A determination

A fiber-optic evanescent wave sensor for bisphenol A (BPA) determination based on a molecularly imprinted polymer (MIP)-modified fiber column was developed. MIP film immobilized with BPA was synthesized on the fiber column, and the sensor was then constructed by inserting the optical fiber prepared into a transparent capillary. A microchannel (about 2.0 μL) formed between the fiber and the capillary acted as a flow cell. BPA can be selectively adsorbed online by the MIP film and excited to produce fluorescence by the evanescent wave produced on the fiber core surface. The conditions for BPA enrichment, elution, and fluorescence detection are discussed in detail. The analytical measurements were made at 276 nm/306 nm (λ(ex)/λ(em)), and linearity of 3 × 10(-9)-5 × 10(-6) g mL(-1) BPA, a limit of detection of 1.7 × 10(-9) g mL(-1) BPA (3σ), and a relative standard deviation of 2.4% (n = 5) were obtained. The sensor selectivity and MIP binding measurement were also evaluated. The results indicated that the selectivity and sensitivity of the proposed fiber-optic sensor could be greatly improved by using MIP as a recognition and enrichment element. Further, by modification of the sensing and detection elements on the optical fiber, the proposed sensor showed the advantages of easy fabrication and low cost. The novel sensor configuration provided a platform for monitoring other species by simply changing the light source and sensing elements. The sensor presented has been successfully applied to determine BPA released from plastic products treated at different temperatures.

Towards water compatible MIPs for sensing in aqueous media

When synthesizing molecularly imprinted polymers (MIPs), a few fundamental principles should be kept in mind. There is a strong correlation between porogen polarity, MIP microenvironment polarity and the imprinting effect itself. The combination of these parameters eventually determines the overall binding behavior of a MIP in a given solvent. In addition, it is shown that MIP binding is strongly influenced by the polarity of the rebinding solvent. Because the use of MIPs in biomedical environments is of considerable interest, it is important that these MIPs perform well in aqueous media. In this article, various approaches are explored towards a water compatible MIP for the target molecule l-nicotine. To this end, the imprinting effect together with the MIP matrix polarity is fine-tuned during MIP synthesis. The binding behavior of the resulting MIPs is evaluated by performing batch rebinding experiments that makes it possible to select the most suitable MIP/non-imprinted polymer couple for future application in aqueous environments. One method to achieve improved compatibility with water is referred to as porogen tuning, in which porogens of varying polarities are used. It is demonstrated that, especially when multiple porogens are mixed, this approach can lead to superior performance in aqueous environments. Another method involves the incorporation of polar or non-polar comonomers in the MIP matrix. It is shown that by carefully selecting these monomers, it is also possible to obtain MIPs, which can selectively bind their target in water.

Molecularly imprinted polymers for selective extraction of synephrine from Aurantii Fructus Immaturus

In this work, molecularly imprinted solid-phase extraction (MISPE) has been used to selectively enrich, purify, or remove synephrine from Aurantii Fructus Immaturus. To this end, a molecularly imprinted polymer (MIP) was prepared by self-assembly from the template synephrine, the functional monomer methacrylic acid, and the crosslinker ethylene glycol dimethacrylate in 1:4:20 molar ratio. Subsequent molecular interrogation of the MIP binding sites revealed preferential structural selectivity for synephrine relative to other structurally related naturally occurring compounds (i.e. octopamine and tyramine ). This selectivity was subsequently exploited to achieve substantial sample clean-up of extracts of crude Aurantii Fructus Immaturus and Aurantii Fructus Immaturus stir-baked with bran. The purity of synephrine in the extracts after MISPE represented approximately 24.21-fold enrichment of the synephrine in the untreated extracts of Aurantii Fructus Immaturus stir-baked with bran. High recoveries (85-90%) from the samples proved that the method was valid for selective enrichment, purification, or removal of synephrine from Aurantii Fructus Immaturus.

Enrichment of (E)-Resveratrol from Peanut Byproduct with Molecularly Imprinted Polymers

Molecularly imprinted solid phase extraction (MISPE) has been employed to isolate and concentrate bioactive polyphenols from peanut press waste. To this end, a molecularly imprinted polymer (MIP) templated with the phytoalexin (E)-resveratrol has been prepared via self-assembly with the functional monomer 4-vinylpyridine (4VP) in a 1:3 molar ratio. Subsequent molecular interrogation of the MIP binding sites demonstrated preferential structural selectivity for (E)-resveratrol with respect to other structurally related naturally occurring compounds. This selectivity was subsequently exploited to achieve substantial sample cleanup of peanut press waste under aqueous conditions with significant enrichment of (E)-resveratrol (>60 fold) requiring minimal sample preparation.

Development of a rubber elongation factor, surface-imprinted polymer–quartz crystal microbalance sensor, for quantitative determination of Hev b1 rubber latex allergens present in natural rubber latex products

Molecularly imprinted polymers (MIPs) for screening to detect rubber latex allergens (Hev b1) in natural rubber based products were designed as artificial recognition polymeric materials coated onto a quartz crystal microbalance (QCM). The polymers were prepared using a stamp imprinting procedure after mixing optimum amounts of methacrylic acid–vinylpyrrolidone–dihydroxyethylene bisacrylamide and Hev b1 latex allergen proteins, obtained from rubber gloves. QCM measurements showed that the resulting polymer layers after removal of the proteins used in their preparation could incorporate structures and features down to nanometer scale of protein templates into the imprinted polymer much better than a non-specific control polymer under controlled sensor conditions and an optimized polymerization process. This selective polymer but not the non-selective polymer clearly distinguished between the latex allergen Hev b1 and proteins such as lysozyme, ovalbumin and bovine serum albumin, with a selectivity factor of from 2 to 4, and the response of the rubber elongation factors by an astonishing factor of 12. The imprinted cavities recognized specific binding sites and could distinguish among related hevein latex allergenic proteins isolated from fresh natural rubber latex; Hev b1, Hev b2, and Hev b3 with a selectivity factor of from 4 to 6. The different QCM measurements obtained presumably reflected slightly different conformations and affinities to the MIP binding sites. The sensor layers selectively adsorbed Hev b1 within minutes in amounts ranging from 10 to 1500 μg L −1 and with a detection limit of 1 μg L −1. This work has demonstrated that this new sensor provides a fast and reliable response to natural rubber latex protein, even after being extracted from the matrix of rubber gloves.

Selective detection of estradiol using a molecularly imprinted self-assembled monolayer on gold surface

Molecularly imprinted polymer (MIP) was synthesized to selectively detect estrogen-like chemicals depending on their shapes and binding characteristics to Estrogen Receptor (ER) active site. MIP was synthesized on self-assembled monolayer (SAM) formed by thiol-acrylate photopolymerization on Surface Plasmon Resonance (SPR) chip. The imprinting factor was calculated based on the shift of SPR angle at which the excitation of surface plasmons by light was minimum level. The imprinting factor, 4.3, was calculated by angle shift by SPR, which showed higher imprinting factor than the previous studies. We also validated the specificity of molecularly imprinted polymer loaded gold chip and compared the binding ability to estrogenicity known by in-vivo and in-vitro biological test. Molecular imprinting reflected the whole surface characteristics including three dimensional shape, types and location of functional groups, and distribution of interaction forces such as hydrogen bonding and van der Waals interaction. Therefore, MIP binding response could provide more insight on structure and estrogenic activity. Another purpose was to provide the basic data for future development of EDC screening array chip to find out various hormone activities at once.

Which molecularly imprinted polymer is better?

Molecularly imprinted polymers (MIP) have been successfully synthesized toward many different compounds in the last decades. The mechanistic details of selective binding at binding sites are not yet well understood. For this reason the characterization of MIP binding has been mostly phenomenological and this makes the transfer of results between different laboratories or between different types of applications difficult. In this paper we analyze the relationship between different types of characterization like isotherms, binding site models, chromatographic k and α values, etc. as they relate to different applications like HPLC, solid phase extraction (SPE), binding assays, batch extraction and sensors. It is shown that α values determined by elution chromatography depend on seemingly irrelevant factors as the length and diameter of the column, respectively. The determination of distribution ratios or partition coefficients is proposed as an easily understandable and useful quantity in the characterization of novel MIPs. Data used for the characterization of a MIP should be transferable between different applications but the qualification of MIPs as better or worse will depend on the application in case.

Zearalenone sensing with molecularly imprinted polymers and tailored fluorescent probes

A molecularly imprinted polymer (MIP)-based optode has been developed for zearalenone (ZON) mycotoxin analysis. The automated flow-through assay is based on the displacement of tailor-made highly fluorescent tracers by the analyte from a MIP prepared by UV irradiation of a mixture of cyclododecyl 2,4-dihydroxybenzoate (template, ZON mimic), 1-allyl piperazine (functional monomer), trimethylolpropane trimethacrylate (crosslinker) and 2,2′-azobisisobutyronitrile in acetonitrile (porogen). Three fluorescent analogues of ZON, namely 2,4-dihydroxybenzoic acid 2-[methyl(7-nitro-benzo[1,2,5]oxadiazol-4-yl)amino]ethyl ester (NBDRA), 2,4-dihydroxy- N-pyren-1-ylmethylbenzamide (PMRA) and of 2,4-dihydroxybenzoic acid 2-[(pyrene-l-carbonyl)amino] ethyl ester (PARA), have been molecularly engineered for the assay development. The pyrene-containing tracers also inform on the characteristics of the microenvironment of the MIP binding sites. PARA has been finally selected to optimize the ZON displacement fluorosensor, that shows a limit of detection of 2.5 × 10 −5 M in acetonitrile. A positive cross-reactivity has been found for β-zearalenol, but not for resorcinol, resorcylic acid, 17β-estradiol, estrone or bisphenol-A.

Molecularly Imprinted Solid‐Phase Extraction of Epicatechin from Tea Beverage

A new molecularly imprinted polymer (MIP) was prepared by using epicatechin as the template molecule. The synthesized MIP was characterized by infrared spectroscopy and scanning electron microscopy, and the MIP with 15–38 µm particle size was selected as a solid‐phase extraction (SPE) sorbent in this work. The maximum MIP binding capacity was 38 µg epicatechin per 100 mg polymer by cartridge test, with a recovery rate of 95.04%. It showed good selectivity and affinity for epicatechin compared with the structurally‐related compounds of quercetin and rutin. The tea samples were also directly applied onto the SPE cartridge and the collected fractions were analyzed by high‐performance liquid chromatography. The MIP cartridge enabled the selective extraction and preconcentration of epicatechin from tea samples.